CONSTRUCTION OF TOWN HALL AT ADITYAPUR MUNICIPAL CORPORATION, JHARKHAND

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l. All kinds of soil.

Extra for earth work in hard soil as per specification and direction of E/I (Vide classification of soil item_B)

Filling in foundation trenches and plenth in layers not exceeding 150 mm thick well watered ,rammed,fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5M all complete as per building specification and direction of E/I

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Foundations,footings,bases of columns , etc for mass concrete

Columns, pillars, piers, Abutments, Posts, Struts

Lintel, beams, plinth beam, Gurder, basements and Centilevers.

Providing and laying in position specified grade of reinforced cement concrete,excluding the cost of centering,shuttering ,finising and reinforcement- all work up to plinth level,1:1.5:3(1 cement : 2 coarse sand : 4 graded stone aggregate 20mm normal size).

Reinforced cement concrete work min wall (any thikness), including attached pilasters, buttresses, plint and string courses, fillets, column,pillars, piers,abutments,posts and struts etc. above plint level up to floor five level, excluding cost of centering, shuttering ,finishing and renforcement: 1:1.5:3( 1 cement : 1.5 coarse sand (zone-III) :3 grade stone aggregate 20 mm normal size).

Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15 degree landing , balcony,shelves, chhajjas, lintel, bands, plain window sills,staircases and spiral stairs cases above plinth level up to floor five five level, excluding cost of centering, shuttering , finishing and renforcement: 1:1.5:3( 1 cement : 1.5 coarse sand (zone-III) :3 grade stone aggregate 20 mm normal size).

Providing TMT reinforcement of 8mm dia rods as per approved -do-TMT Fe 500(only valid for tata,sail,jspl,electrosteel,bokaro and vizag)

Providing TMT reinforcement of 10mm, dia rods as per approved -do-TMT Fe 500(only valid for tata,sail,jspl,electrosteel,bokaro and vizag)

Providing TMT reinforcement of 12mm,16mm dia rods as per approved -do-TMT Fe 500(only valid for tata,sail,jspl,electrosteel,bokaro and vizag)

Providing designation 75 A brick work in C.M. (1:3) in superstructure with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing 25mm thick water proof cement plaster -do-

Structural steel work in single section ,fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a primer coat of approved steel primer all complete

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing and fixing of Glass fiber reinforced cement panel with specification of compressive strength (ls 516) 35-55 Mpa pre mix and 40-66 Mpa, tensile strength 4-7 Mpa(pre mix), 6-11 Mpa(spray), Density(ASTMC-948) 1.8-2.0 gms/cum (pre-mix), 1.8-2.2 gms/cum(Spray), Impact strength 7-15 Kg/sqm(pre-mix), 7-20kg/sqm (spray), fibre content 2.5 to 3.5 %by weight (pre mix), 3-5 %by weight(spray), thickness- 25mm to 50mm as per specification of architect, weight 25 to 70kg/sqm depending upon the design, acid wash-stone finish/ smoother painted all complete as per approved design and as per supervisor incharge /Architect. Providing and fixing of Glass fiber reinforced concrete (G.R.C.) panels in approved size, pattern, design, thickness and color of M/s. JK BRIGHT make or equivalent. The panels should be made from 53 grade white portland cement manufactured by JK cement or equivalent, Quartz, fine silica sand, Alkali resistant glass fibre manufactured by NEG or equivalent, super plasticizers manufactured by BASF or equivalent, polymers manufactured by BASF or equivalent and U.V. resistant synthetic inorganic pigments should be used for pigmentation manufactured by BAYFERROX (germany) or equivalent. The material casting should take place in synthetic rubber /FRP mold manufactured by reckli or equivalent. The fixing of screens should be dry fixing i.e. to be done with stainless steel (SS-304)L shaped brackets, fasteners and pins.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

1:2:4 (1 Cement ;2 coarse sand (zone-III):4 grade stone aggregate 20 mm normal size)

Providing designation 75 A brick work in C.M. (1:3) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size).

Providing designation 75 A brick work in C.M. (1:3) in superstructure with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Reinforced cement concrete work in arches,archribs, domes , vaults,shells,folded plate and roofs having slope more than 150 up to floor five level, excluding the cost of centering, shuttering, finishing and renforcement, with 1:1.5:3(1 cement : 1.5 coarse sand (zone-III):3 graded stone aggregate 20mm normal size).

Roof slab

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinfoorced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Enginner-in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture . M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45degree angle on both side forming styles; and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10mm (5mm x 2 ) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge. Manufacturer’s specification & drawing. (ii)30 mm thick pre laminated PVC door shutters.

Using R2 series with frame (39mm & above) x (39mm & above) & sash (39mm & above) x (60mm & above) & mullion (39mm & above) x (60mm & above). (Height upto 1.2 meter; each openable shutter upto 0.8m width)

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 1000x1000 mm

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 -do-

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/l.

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/l.

Making plinth protection 50mm thik of cement concrete 1:3.:6 (1 cement :3 coarse sand :6 grade stone aggregate 20 mm normal size) over 75 mm thik ded dry brick ballast 40mm normal size well rammed and cansoldiated and grouted with fine sand including nessesary excavation leving and dressing & finishing the top smooth.

wash basin slab

providing and fixing at or near ground level precast cement concrete in kerbs,edgings etc.asper approved pattern and setting in position with cement motar 1:3 (1 cement :3 corse sand),including the cost of requirment centering,suttering complete.1:11/2 :3 (1 cement :11/2 coarse sand (zone-III):3 grade stone aggregate 20mm nominal size).

Extra for plaster work over exterior surface for each consecutive floor avobe first floor including cost of scafolding etc. all complete as per direction of engineer in charge.

Making 6mm X 6mm grooves in plaster surface over wall truely horizontal or vertical as specified at regular intervals at all heights including cleaning, finishing, scaffolding and curing with all leads and lifts of water all complete as per building specification and direction of E/I.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Suppling, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood- 50 x 20 mm

French spirit polishing : Two or more coats on new works including a coat of wood filler

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete : 25 mm dia

Providing and fixing of curtain with approved design and shade of curtain all complete as per supervisor incharge.

Providing and fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Rockwool conforming to IS: 8183,density 48 kg/ m3, 50 mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fixing, in position concealed G.I. section for wall paneling using board of required thickness fixed on the 'W' profile (0.55 mm thick) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. Board is fixed to the 'W' profile with 25 mm countersunk ribbed head screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-in-charge, the joints of the boards are finished with specially formulated jointing compound and 48mm wide jointing tape to provide seamless finish. Tapered edge calcium silicate board made with calcareous & siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with compressive strength 225 kg/ sq.cm, Bending strength 100 kg/sq.cm. 10mm thick

Providing& Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality:1.5 mm thick

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing of Glass fiber reinforced cement panel with specification of compressive strength (ls 516) 35-55 Mpa pre mix and 40-66 Mpa, tensile strength 4-7 Mpa(pre mix), 6-11 Mpa(spray), Density(ASTMC-948) 1.8-2.0 gms/cum (pre-mix), 1.8-2.2 gms/cum(Spray), Impact strength 7-15 Kg/sqm(pre-mix), 7-20kg/sqm (spray), fibre content 2.5 to 3.5 %by weight (pre mix), 3-5 %by weight(spray), thickness- 25mm to 50mm as per specification of architect, weight 25 to 70kg/sqm depending upon the design, acid wash-stone finish/ smoother painted all complete as per approved design and as per supervisor incharge /Architect. Providing and fixing of Glass fiber reinforced concrete (G.R.C.) panels in approved size, pattern, design, thickness and color of M/s. JK BRIGHT make or equivalent. The panels should be made from 53 grade white portland cement manufactured by JK cement or equivalent, Quartz, fine silica sand, Alkali resistant glass fibre manufactured by NEG or equivalent, super plasticizers manufactured by BASF or equivalent, polymers manufactured by BASF or equivalent and U.V. resistant synthetic inorganic pigments should be used for pigmentation manufactured by BAYFERROX (germany) or equivalent. The material casting should take place in synthetic rubber /FRP mold manufactured by reckli or equivalent. The fixing of screens should be dry fixing i.e. to be done with stainless steel (SS-304)L shaped brackets, fasteners and pins.

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 3 mm thick.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.

1:2:4(1 cement :2 coarse sand (zone=lll):4 grade stone aggregate 40 mm norminal size)

Providing designation 75B brick work in CM (1:6) in superstructure with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I

Providing 1.5 mm. cement punning including curing carrage of water withall leads and lifts as per building specification and direction of E/I

Supplying and fixing C.I. cover without frame for manholes : 560 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

Making soak pit 2.5 m diameter 3.0 m deep with 45x45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size ange 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer for all leads & lifts, all complete as per direction of Engineer -in- charge.

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. Basic Rates

From 0 - 50 meter

From 51 - 125 meter

Supply of 200mm dia X 2.00m long UPVC casing pipe conferming to IS : 12818 : 2016 (CML No. 5543459) latest revision including carriage.

Supplying all materials, labours, equipments for lowering blue UPVC casing pipes as casing for protecting the sides from falling during the process of drilling all complete including carriage of materials to work site.

Supplying all tools, equipments and labour and doing washing, flushing and development of drilled tube well to give clean and clear water all complete as per direction of E/I.

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/ Noryl Impeller) up to 20 stages

PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminium conductor for working voltage up to and including 1100 volts.(Conforming to IS:1554, part-1)

63 amp. Four pole, on load change over switch in sheet enclousre with side handle operation.

Medium density polyethylene pipe (MDPE pipe) in standard length with necessary Jointing material like mechanical connector i.e., thread/insert joint / quick release coupler joint / compression fitting joint or flanged joints confirming to ISO: 4427 : 1996

Polythene water storage tank of mark with cover and suitable locking system in double layer confirming to IS: 12701-1996 with latest revision.

Providing & fixing brass stop cock of approved quality all complete as per specification and direction of E/I.

(A) Brass stop cock

(b) 20 mm dia

(c) 25 mm dia

(d) 32 mm dia

(e) 40 mm dia

Providing & supplying in standard lengths High density polyethylene pipe (HDPE pipe) confirming to IS 4984 / 14151/ 12786 / 13488 (latest revision with necessary jointing material like mechanical connector i.e., thread / insert joint / quick release coupler joint / compression fitting joints or flanged joints ecluding coupler / specials and taxes)

25 mm dia

32 mm dia

Supplying and fixing G.I. fittings of approved make (conforming to I.S:-1879) all complete as per specification and direction of E/I.

(1) Elbow

25 mm dia.

32 mm dia.

40 mm dia.

(2) Tee (plain)

25 mm dia.

32 mm dia.

40 mm dia.

(3) Reducing Socket

25 mm dia.

32 mm dia.

40 mm dia.

(4) Nipple

25 mm dia.

32 mm dia.

40 mm dia.

(5) Plugs

25 mm dia.

32 mm dia.

40 mm dia.

(6) Reducing Tee plain (taking Larger Dimension)

25 mm dia.

32 mm dia.

40 mm dia.

(7) Union Socket

25 mm dia.

32 mm dia.

40 mm dia.

(8) Socket

25 mm dia.

32 mm dia.

40 mm dia.

(9) Bends

25 mm dia.

32 mm dia.

40 mm dia.

(10) Jam Nuts

25 mm dia.

32 mm dia.

40 mm dia.

Making long screw in G.I pipe including supplying and fitting jam nuts and extra socket etc. all complete as per specification and direction of E/I.

25 mm dia.

32 mm dia.

40 mm dia.

Cutting chazza or cornice for laying G.I. pipe and restoring the same with R.C.C. (1:2:4) brick work in cement mortar (1:4) and cement plaster (1:4) as per specification and direction of E/I.

Making holes in walls for laying G.I. pipes and restoring the same after pipe laying as per specification and direction of E/I.

125 mm thick wall

250 mm thick wall

R.C.C. Chazza

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware I.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of "Hindustan" " Parry" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l.

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l.

Supplying, fitting and fixing white glazed fires clay sink of approved make with overflow arrangements supported on C.l. or R.S. painted brackets 40 mm dia C.P. brass waste with C.P. brass chain and rubber plug, 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one end and 15 mm C.I. body brass spindle bib cock of approved quality of weight not less than 450 grms. including cutting wall and making good the same etc. all complete as per specification and direction of E/l.

Providing and fixing lead connection pipe with heavy quality brass coupling 2 Nos. at both ends etc. all complete as per specification and direction of E/l .

Providing and fixing N.P/C.P brass/P.V.C porcelain shower rose of 15mm inlet etc. all complete as per specification and direction of E/l

Providing and fixing male ended 15 mm dia brass bib cock of approved quality ( wt not less than 350 gms ) with extra socket all complete as per specification and direction of E/l .

Providing and fixing 15mm size C.P brass pillar cock (Weight not less than 350 gms) C.I body brass spindle pillar cock of approved quality as per spcification and direction of E/l.

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/l.

Glass shelf with C.P brass rail

Mirrors of 4 mm thick plate glass bevelled edge mirror including C.P brass revolving fittings, 3 mm plywood board and C P hinges to fix with mirror

i) C.P brass towel rail 20 mm x 600 mm with bracket container

ii) C.P brass shop dish container medium quality with screw and hinges etc.

(iii) C.P brass liquid shop container

Supplying fitting and fixing H.C.I, pipes with ear of approved make confirming to I.S.I. 1729 including supplying nails and bobins short pieces, cutting loose collars, lead and yarn for making lead chaulked joints, cutting pipes to size including earth work or scaffolding where neccessary etc. all complete as per specification and direction of E/l.

(a) 100 mm dia

(b) 75 mm dia

(c) 50 mm dia

Supplying and fixing H.C.I, fittings of approved make confirming to I.S.S. 1729 including supplying nails and bobins lead and yarn for making lead chaulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/l.

(A) H.C.I, single junction with door but without ear except socket

(i) 100mmdia(Wt. 10.5 Kg. app.)

(ii) 80 mm dia (Wt. 7 Kg. )

(B) H.C.I. Heal Rest Bend

(i) 100 mm dia (Wt. 5.5 Kg. app.)

(ii) 80 mm dia (Wt. 4 Kg. app.)

( C) 100mm dia H.C.I."P" TRAP with Anti syphonage Horn (Wt. 8.5 Kg. app.)

(D) H.C.I, double junction with door and ear

(i) 100 mm dia (Wt. 15.5 Kg. app.)

(ii) 80 mm dia (Wt. 15.5 Kg. app.)

(E) H.C.I, double inverted Jn.

( 100 mm x 50 mm x 50 mm size)

(F) H.C.I, offset with ear

(i) 100 mm dia (Wt. 6 Kg. app.)

(ii) 80 mm dia (Wt. 4 Kg. app. )

(G) H.C.I, bend with door and ear

(i) 100 mm dia (Wt. 6.5 Kg. app.)

(ii) 80 mm dia (Wt. 4.5 Kg. app.)

(H) H.C.I plain bend with ear

(i) 100mm dia (Wt. 5.5 Kg. app.)

(ii) 80 mm dia (Wt. 3.75 Kg. app.)

(J) Floor trap with gratinqs

(i) 100 mm dia

(K) Norton patent H.C.I, cowel

(i) 100 mm dia (Wt. 3.25 Kg. app.)

(ii) 80 mm dia (Wt. 2.25 Kg. app.)

(L) H.C.I. pass over

(i) 100 mm dia

(M) H.C.I, sinqle inverted junction with ear

(100 mm x50 mm)

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750 mm deep, 600 x 450 internal dimension having 250 mm wall thickness in cement mortar ( 1:6 ) including 12 mm cement plaster ( 1:4 ) with punning on inside and cement plaster (1:6 ) with 600 x 475 mm G.I. cover with frame (Weight not less than 36 Kg.) in foundation and refilling all complete as per specification and direction of E/l.

Providing & supplying in standard lengths High density polyethylene pipe (HDPE pipe) confirming to IS 4984 / 14151/ 12786 / 13488 (latest revision with necessary jointing material like mechanical connector i.e., thread / insert joint / quick release coupler joint / compression fitting joints or flanged joints ecluding coupler / specials and taxes)

110 mm dia

75 mm dia

140 mm dia

200 mm dia

Earth work in excavation ( as per I.S. 3114/1965 for laying of different types and sizes of pipes so as to give 1 m av. cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of E/l.

Earth work in back filling the trenches after laying different types and size of pipes with earth removed dufing excavation within initial lead and lift as per specification and direction of E/l. ( For classification of Soil item - A & B)

Providing & supplying in standard lengths High density polyethylene pipe (HDPE pipe) confirming to IS 4984 / 14151/ 12786 / 13488 (latest revision with necessary jointing material like mechanical connector i.e., thread / insert joint / quick release coupler joint / compression fitting joints or flanged joints ecluding coupler / specials and taxes)

Providing and fixing male ended 15 mm dia brass bib cock of approved quality ( wt not less than 350 gms ) with extra socket all complete as per specification and direction of E/l .

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge.

Providing & laying vitrified paring/Industrial tiles in different sizes with water absorption less than 0.08% and confirming to IS: 4457:2007, of approved make in all colors and shades, laid on 20mm thick cement mortar 1:4, jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete size of tile 300 X 300 X10mm sizes.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1KV grade of size exceeding 95 sqmm but not exceeding 185 sq mm direct in ground including excavation, sand cushioning, protective covering and refiling the trench etc as required.

PVC / XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminium conductor for working voltage up to 1100 volts. (Conforms to IS : 1554, part-1)

Supplying and making cable route marker with cement concrete 1:2:4 (1cement: 2coarse sand : 4graded stone agreegate 20mm nominal size) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10 cm including inscription duly engraved as required.

Providing & fixing M.V. danger notice plate of 250 mm X 150 mm, made of mild steel, at least 2mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

P/F G.I. lighting conductor finial :- providing and fixing of lighting conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

P/F G.I. lighting conductor tape in horizontal run:- providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lighting conductor complete as required.

P/F G.I. lighting conductor tape in vertical run:- providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lighting conductor complete as required.

Reverting, sweating and soldering of copper / G.I. tape with another copper / G.I. tape, base of finial or any other metallic object as required.

Providing fixing testing joint made of 20 mm X 3 mm thick G.I. strip 125 mm long with 4 nos G.I. bolts. Nuts chuck nuts and spring washers etc. complete as required.

Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal or cock and salt) complete etc. as required.

S/L 8 SWG G.I. wire in ground :- Supplying and laying 8 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required.

Providing & laying earth connection from earth electrode with 4mm dia copper wire in 15mm dia G.I. pipe from earth electrode, as required.

Silent type DG set of capacity 125 KVA with AMF panel IS/IEC-60034-1 IS: 1460 IS:13018

Earthing with copper earth plate 600mm X 600mm X 3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangements with watering pipes etc.(with charcoal or coke, salt) as required.

30 KVA online UPS three phase input and three phase output power system of input, voltage range 360V/380v/400v/485v AC, frequency range 40HZ-60HZ +/- 10%, output voltage range 415v +/- 1%, frequency range 50HZ +/- 1% power factor 0.8/3:1, Harmonic distortion- <2% THD(Linear load) : 5% THD (Non- linear Load)

MS battery rack suitable for 30-35 UPS battery installation.

100Ah tubular lead acid battery with 36 month replacement gurantee, IS:1652:1991

160 KVA Distribution Transformer

16 amps, double pole

32 amps, double pole

63 amps, double pole

32 amps, TP&N

63 amps, TP&N

25 - 100 amps, 10 KVA fixed thermal setting

25 - 100 amps, 16 KVA fixed thermal setting

125 amps, 16 KVA fixed thermal setting

Providing and fixing following capacity bus bar chamber with 4 strips of length 300 mm made of copper suitable for following capacity complete with all accessories including connections, earthing the body etc. as required

32 amps, 2 pole

63 amps, 2 pole

4 way ( 8 + 12 ), double door vertical type

8 way ( 8 + 24 ), double door vertical type

6/32 amps, single pole

40 amps, single pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Group A

Group B

Group C

Wiring for twin control points with 1.5 sq mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, 2 way with modular switch, modular plate, suitable GI box etc. as required.

Wiring for light/power plug with 2 X 4 sq mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, along with 1 nos 4 sq mm FR PVC insulated copper conductor single for loop earthing etc as required.

Wiring for light/power plug with 4 X 4 sq mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, along with 2 nos 4 sq mm FR PVC insulated copper conductor single for loop earthing etc as required.

2 X 1.5 sq mm + 1 X 1.5 sq mm earth wire

2 X 2.5 sq mm + 1 X 2.5 sq mm earth wire

2 X 4 sq mm + 1 X 4 sq mm earth wire

2 X 6 sq mm + 1 X 6 sq mm earth wire

2 X 10 sq mm + 1 X 6 sq mm earth wire

Supplying and fixing stepped type electronic fan regulator on the existing modulat plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate & switch box excluding modular plate etc. as required.

1 or 2 Module

4 / 5 Module

6 Module

8 / 9 Module

12 Module

Supplying and fixing suitable GI box with modular plate and cover in front on surface of in recess, including providing & fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch connection, painting etc. as required (For light plugs to be used in non residential buildings)

Supplying and fixing suitable GI box with modular plate and cover in front on surface of in recess, including providing & fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch connection, painting etc. as required (For light plugs to be used in non residential buildings)

Supplying and fixing 2 pin 5 amp. Ceiling rose on the existing junction box / wooen block including connection etc. as required.

Supplying and fixing Batten / angle holder including connection etc. as required.

Supplying and fixing ding dong sound call bell single phase 230 voltscomplete as required.

Supplying, Installation, testing & commisioning of following size ceiling fan 3 blades confirming to IS:374:2019 including the wiring down rods of standard length up to 30 cm with 1.5 sq mm FR PVC insulated copper wire suitable for 230V 50HZ, single phase supply etc. complete as required.

Installation of exhaust fan up to 450 mm sweep in the existing opening including making the hole to suit the size of the above fan making good the damage, connection, testing , commissioning etc. as required.

15" (380 mm ) metal exhaust fan

18/20 W LED Round Down light

1' X 1' LED Panel light

6 W COB based round LED light with multiple beam angles (36 degrees)

9 W COB based round LED light with multiple beam angles (36 degrees)

Approved make wall mounted decorative lamp with nickel / chrome finish with opal glass of lamp type E27 / E22 LED 7/9 W X 2 IS: 10322 part 5

S.I.T.C. of flowing rating reccess / surface mounted LED round / Square shade down light luminaire with pressure die cast housing for single phase supply voltage. Luminaire shall be confirming to IS: 10322 part-5 / section-2 or IEC:62722 with all neccssary accessories as required.

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

Steel circular hollow pole of standard specification for street lighting to mount light at 5m height above deck level.

S.I.T.C. of flowing rating LED street lighting luminaire with pressure die cast housing and toughned glass cover (IP 66 protection) in existing pole/pipe for supply voltage 100-270 V AC, 50HZ luminaire shall be confirming to IS: 10322 part-5/section-3 and shall be complete with all neccessary accessories as required.

S.I.T.C. of flowing rating approved make LED bollard fitting with rectangular shape of height 600 to 850mm power input-8/9 watt with die cast aluminium housing opel with PC diffuser, IP:65/54 protection, confirming to IS:10322 part 5 etc all complete as required.(excluding plinth charge)

Supply of 16 m high mast in two section construction S355 grade as per BS-EN 10025 top dia 150 mm, bottom dia 360mm, plate thickness 3mm, 20 side polygon, galvanisation as per BS EN ISO 1461, base plate dia 520 mm, base plate thickness 25mm , GI single spike lighting protection, maximum wind speed 47m/s with 6 nos foundation bolts of PCD 445 mm TS 600 / 24mm dia/850 mm long. Luminaire carriage: Material for 40NB ERW Class B-M.S. pipe dia of carriage ring 450mm(ID) with 8/12 arm, welded, 2 sections having carrying capacity up to 8 / 12 luminaires. Trailing cables : 5core 2.5 sqmm. pvc flexible copper conductor winch/powel tool: double drum, SWL 350 kg with 1HP 6 pole single speed integral motor rope : grade AISI 304, 7/19 Construction, dia 5mm, BLC 1450 X 2 having 2 nos continues rope. Aviation obstruction light : twin dome aviation obstruction lights LED type as required. but exceeding feeder pillar

For 16 mtr High mast light: ITC of the high mast and light fixture with the help of suitable tools and plants, wiring of luminaires with all wiring materials like PVC insulated PVC sheathed flexible cable of suitable copper conductor lugs, MCB and all labour & construction of shallow foundation with M25 grade concrete for the high mast considering safe soil bearing capacity of 10T/sq m for 16 M high mast light.

Outdoor stand mounted feeder Panel with 63 amp TP&N, MCB incomer, 63 amp TP contactor automatic switching of luminaires, power tool control Incommer out going terminal etc. as required. (High Mast light).

2.0 Tr 5 star split AC (inverter type) IS-1391-Part-1

Copper tube of size 3/8'' for split ac unit 1/1.5/2/3 tr capacity including nitride rubber insulation

Drain Pipe for AC

Outdoor stand for 2.0tr split AC

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and carriage upto 5 km complete (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) : 2.4.3 Screened through sieve of I.S. designation 4.75 mm

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Preparation of beds for hedging and shrubbery by excavating 60 cm deepand trenching the excavated base to a further depth of 30 cm, refilling theexcavated earth after breaking clods and mixing with sludge or manure inthe ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%),flooding with water, filling with earth if necessary, watering and finally finedressing, leveling etc. including stacking and disposal of materials declaredunserviceable and surplus earth by spreading and leveling as directed,within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Providing and displaying of Philodendron Burgundy plant mounted on moss stick 90 cm ht., well developed with full of fresh & healthy leaves from bottom to top in 25 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Philodendron emrald red colour plant, mounted on moss stick 90 cm ht., having 3 plants placed at equal distance, well developed with full of fresh & healthy leaves in 25 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Aglaonema Silver Queen having 30 cm to 45 cm. ht. with 12 to 15 leaves, multi suckers, fresh and healthy leaves, well developed in 25 cm dia Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Aglaonema ernesto (three in one), having ht. 45 cm & above with 12 to 15 leaves, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot.& as per direction of the officer-in-charge.

Providing and displaying of Aglaonema marentifolium variety having ht. 23 cm to 30 cm with 8 to 10 leaves, well developed, fresh and healthy with colorful leaves in 20 cm size of Earthen pot/Plastic pot. & as per direction of the officer-in-charge.

Providing and Displaying of Alpinia Variegated (three in one) plant having ht. 30 cm and above , with fresh and healthy variegated foliage in 25 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in charge.

Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Asparagus marrie, well developed 15 to 20 leaves, full of branches and foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Euphorbia milli hybrid variety, having ht. 30 cm to 45 cm with multi branch, full bloom, fresh and healthy leaves in 30 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge..

Supply and stacking of Delonix regia (Gulmohar) plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and displaying of Phoenix palm having ht. 75 cm to 90 cm with 10 to 15 or more leaves, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Supply and stacking of Nauclea cadamba (Kadam) plant of height 150-165cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.v

Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Michelia champa (Golden Champa) of height 90- 105 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Butea frondosa (Flame of Forest) of height 60-75 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of plant Bauhinia tomentosa (yellow) of height 60-75 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge

Providing and stacking of Iresine herbstii, of height 20-25 cm. full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Juniperus prostrata with 5 to 6 latral branches and green foliage in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)

Supply and stacking of Bignonia venusta (Golden shower) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Supply and stacking of Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara,Mohan,Scarlet Queen, Varigata, Glabra Formosa, Peruviana Odissi, Partha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) plant of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. .

Supply and stacking of Jasminum grandiflorum (chameli) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. .

Providing and stacking of Clerodendrum splendens of height 30 cm to 45cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Clerodendrum thomsoniae of height 30 cm.to 45 cm in 20 cm size of poly bag & as per direction of the officer-in-charge.

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) Open spaces(as per yard stick 1Mali =3.00Acre).

Bricks =10 km(7+3)

Sand=15 km(10+5)

Stone chips =30 km (25+5)

Cement (5km)

Steel (5 km)

Supplying,installing,testing and comissioning of MS Pipe line Medium grade conforming to IS-1239 including all fittings i.e. bend,elbows,tees,flanges,reducing socket,nuts and bolts,gaskets etc fixed with welded / screwed joints including necessary fittings,fixed with screwed or welded joints,hanged with clamps ,hanger supports,dash fasteners,bolts,nuts,rubber insertions etc including threading,cutting,welding,edge preparation,painting or approved colour over two coat primer,cutting and making good the wall /floor wherever required,complete as required or as directed by engineer incharge.

100 mm dia

80mm dia

65mm dia

50mm dia

40mm dia

32 mm dia

25 mm dia

Supplying,installing,testing and commissioning of C.I. butterfly valves as per BS 5155(PN 16) slim seal standard lever operated type with required flanges,nuts,bolts etc. complete

100mm nominal dia

80mm nominal dia

Supplying,installing,testing and commissioning of C.I. Non-return valves as per IS:5312(PN 16) swing check type with required flanges,nuts,bolts and gaskets etc. complete.

100 mm nominal dia

80mm nominal dia

Supplying,installing,testing and comissioning of Hydrant valve with 63 mm outlet/inlet GM instantaneous female coupling with rubber cap and chain conforming to IS:5290, including matching flange ,gasket,nuts & bolts complete.

Providing and fixing of of 63 mm dia 15 mtr long rubberised fabric stainless steel lined hose including male and female instantaneous type coupling approved by fire authority.(ISI Marked)

Providing and fixing of standard short size stainless steel branch pipe with nozzle 20 mm dia outlet with standard instantaneous type 63 mm dia coupling (ISI Marked)

Providing and fixing MS Hose Box (Single Door) with lockable arrangements to accommodate 1 reel hose of 15 mtr length and 01 no of branch pipe painted white inside and red outside with one key.

Providing and fixing swinging,wall mounting type First aid fire hose reel of approved quality and made from compressed steel sheet with dust cover,cast iron brackets including 30m long ,19mm nominal bore,high pressure braided rubber hose .Type hose guide,PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve,bolts,nuts,rubber insertion etc Painted in fire red colour including cutting and making the walls wherever required.( ISI Marked)

Supplying,Installing,Testing and Commissioning of quartz sprinkler bulbs along with necessary fittings.(ISI Marked)

Supply,Installation,Testing and Commissioning of Pressure gauges of suitable range for pump sets and pipe lines with siphon,fittings likes unions/collars/reducers etc. Glycerine filled pressure gauges to use on pump discharge lines.

Supply,installation,testing and comissioning of 4 way Fire Brigade inlet connection with 3 nos. 63mm dia built-in S.S Npn-return valves,instantaneous coupling type arranged on 150mm dia pipe manifold and connected to External Hydrant Ring as well as to the Fire water tank.

Providing and fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome-plated steel ball tested to a pressure not less than 16 Kg/sq.cm with threaded /flanged joints complete with nuts,bolts,gaskets,washers etc. 25mm dia

Supply,installation,testing and commissoning of MS Air Release Valve of 25mm dia of approved quality.

FOOT VALVE(150mm) Make-Kartar/Atasee/Eqv.

Pressure Switch

Supply, Installation, Testing and Commissioning of electric driven, horizontal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impellers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC supplywith IP 55 protection for enclosurewith F class insulation confirming to IS: 325 includingcommon base frame fabricated from min. 75X50 mm M.S channel, coupling with guard foundation bolts, pressure gauge, anti-vibration pads, cement concrete foundation etc. complete in all respect as required or as directed by engineer incharge. MAKE :- Kirloskar/KSB/PEW

MAIN FIRE PUMP,1650 LPM,36 M Head

JOCKEY PUMP,7.5 HP

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, having switchgears and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42 with 400 Amp aluminium bus bar as required. Make:- L&T /HoneyweEQV.

Supply and installation of conventional type Fire alarm and Control Panel (4 Zone) with 2x16 character LCD display ,Power supply ,battery charger,Inbuilt Battery box,12 MHZ speed ,Feather touch switch.(Tested by ERTL)

Providing and fixing MANUAL CALL POINT,Front protection glass cover,ABS housing with back box.(24 V)

Providing and fixing hooter 24 V suitable for the control panel.

Providing and fixing 2 Core 1.5 sq mm FRLS wires (In PVC conduits) Make: Polycab/Mescab.

Optical Smoke Detector+Base,Remote LED

CP PLUS IP DOME CAMERA

CP PLUS IP BULLET CAMERA

32 CH NVR 200 MBPS 2 SATA

HARD DISK 10TB Enterprises 24*7 Surveillance (WD) PURPLE

HARD DISK 4TB Enterprises 24*7 Surveillance (WD) PURPLE

CP PLUS POE With Gigabit

LG Monitor 42"

CAT6 CABLE DLINK 305 MTR (23AWG SOLID) (in Bundle)

D-LINK 6U RACK

D-LINK RJ 45 Connector (in Box)

CP PLUS IP DOME CAMERA

CP PLUS IP BULLET CAMERA

32 CH NVR 200 MBPS 2 SATA

HARD DISK 10TB Enterprises 24*7 Surveillance (WD) PURPLE

HARD DISK 4TB Enterprises 24*7 Surveillance (WD) PURPLE

CP PLUS POE With Gigabit

LG Monitor 42"

CAT6 CABLE DLINK 305 MTR (23AWG SOLID) (in Bundle)

D-LINK 6U RACK

D-LINK RJ 45 Connector (in Box)

Main Valance fixing arrangement using 40NB MS pipe, 2mm thick, 14 Mtr in length undergone through 7 tank process with various chemical treatment to keep them rust free duly powder coated with matt black texture finish with mounting brackets to suspend the arrangement.

Main curtain track system 17 Mtr long, centre parting with overlap of 0.9mtr provided with, Heavy duty extruded curtain track of 48x84mm, powder coated Track mounting brackets constructed of C track of dimension 40X50X40mm Electromechanical drive unit with 3PH INDUCTION MOTOR, 1.1KW, 3000RPM, 90B5 FLANGE MOUNT with GI wire ropes of 3mm in diameter constructed with 7 bundles of 7 strands with steel core at center Curtain holding Nylon wheel trollies consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of 200mm throughout the track.Nylon moulded 6201 Ball bearing Diverter pulley with with 90mm for outer diameter, 72mm diameter at groove base, 19mm pulley thickness & MS yellow passivated Routing pulleys with 165mm for outer diameter, 150mm diameter at groove base with 12mm pulley thickness.

Rear curtain track system 14 Mtr long, centre parting with overlap of 0.9mtr provided with, Heavy duty extruded curtain track of 48x84mm, powder coated Track mounting brackets constructed of C track of dimension 40X50X40mm Electromechanical drive unit with 3PH INDUCTION MOTOR, 1.1KW, 3000RPM, 90B5 FLANGE MOUNT with GI wire ropes of 3mm in diameter constructed with 7 bundles of 7 strands with steel core at center Curtain holding Nylon wheel trollies consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of 200mm throughout the track.Nylon moulded 6201 Ball bearing Diverter pulley with with 90mm for outer diameter, 72mm diameter at groove base, 19mm pulley thickness & MS yellow passivated Routing pulleys with 165mm for outer diameter, 150mm diameter at groove base with 12mm pulley thickness.

MS, Wing frame construction, made out of MS square pipe with 2mm in thickness powder coated of size H 7.5 Mtr x W 2 Mtr, provided with 1.5meter wing track of 48X84mm with gridmount brackets made of 40X50X40mm C track Pivotable 4 wheeled suspension trolley Adjustable floor locking screw jacks with rubber grips Inverted 4-Wheeler Trolley with Flexi Adaptor Clamp Extruded track Aluminium I Profile to be laid through out the dept of the stage

Cyclorma arrangement using aluminium extruded ''I'' track of 48 x 84mm duly powder coated in black texture finish to use as straight cyclorama track with MS fabricated Grid/wall mount bracket constructed of C track of dimension 40X50X40mm duly powder coated to hold the track, MS fabricated Tie down railing cut length 3 mtr duly powder coated to keep the cyclorama in drum tight arrangement, 2 wheeler trolley placed uniformly at specific interval of 200mm throughout the track, MS powder coated Leading edge frame to keep the cyclorama in drum tight arrangement of Size L 10 Mtr x 6Mtr.

MS Fabricated made up of 22SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish power junction box (PJB) to terminate the Motorized section power connections.

Well designed and engineered Wall mount 2 feeder motor control centre panel & Remote control panel with emergency trip necessary contactors and relays to control the motors system for curtains Mechanism. (MCCP/RCP - 2)

Fire retardant velvette fabric 100% (2 times of the finished dimension) gathering for main Valance as per the approved patern and colour, not less than 300 GSM, duly stitched along with and eyelets. Size : L 14 Mtr x H 1.5 Mtr.

Fire retardant velvette fabric with lining 100% (2 times of the finished dimension) gathering for main curtain as per the approved patern and colour, not less than 300 GSM, duly stitched along with eyelets. Size: L 9 Mtr x H 7.5 Mtr.

Fire retardant cotton fabric 50% (1.5 times of the finished dimension) gathering for frills as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size: L 10 Mtr x H 1.2 Mtr. ng

Supply and Installation of, square edge,Glassfibre corefully encapsulated ceiling tile of size 595x595x15mm having volume density 120Kgs/m3, weight 1.8 kg/m2 which is suspended by using 0.3mm thick Skelet Trelis metal grid system. Skelet Trelis metal grid system of 600x600mm module includes wall angle with unequal flanges of 15/19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Skelet Main T with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main Skelet Trelis at 600mm centers in the perpendicular direction to the Main Skelet. Finally Skelet CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CrossT in direction parallel to the Main T o result in 600x600mm module. Nubby square edge of size 595x595x15mm shall be placed into the grid size of 600x600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. Technical Parameters: - • Fire (Class) – 1 & P, • Acoustics – NRC 0.9 (For E900 Mounting), • Thermal conductivity (W/mk)– 0.066, • Climate (°C, RH) – 40, 95, • Light reflectance (%) – 85, • Green (VoC, RC %) – Low, 35. 595x595x15mm, Square edge (Grid system)

Supply and Installation of Ebony,square edge, Glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having volume density 120 Kgs/m3, weight 1.8 kg/m2 which is suspended by using 0.3mm thick Skelet Trelis Ebony metal grid system. Skelet Trelis Ebony metal grid system of 600x600mm module includes Skelet wall angle with unequal flanges of 15/19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Skelet MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T at 600mm centers in the perpendicular direction to the Main T. Finally Skelet CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CrossT in direction parallel to the Main T to result in 600x600mm module. Subtex Ebony square edge of size 595x595x15mm shall be placed into the grid size of 600x600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. Technical Parameters: - • Fire (Class) – 1 & P, • Acoustics – NRC 0.9 (For E900 Mounting), • Thermal conductivity (W/mk)– 0.066, • Climate (°C, RH) – 40, 95, • Light reflectance (%) – na

Supply and Installation of Strand, Kerfed edge Magnesite bonded pinewood fibre core tiles of size 600x2400x20mm, density 400 kgs/m3, weight 8kg/m2 installed by using Strut framework system with non-visible fasteners using H-Spline. The Strut framework systems includes Strut Cross Channel having thickness 0.55mm, length 3600mm, knurled web 25, depth. - 25mm and equal flanges 12mm is fastened to wall positioned horizontally in a regular manner at 600mm c/c with support of MC 45. H-Spline having sectional thickness 2mm and length 2400mm to be fixed perpendicular to the Strut Cross Channel at 600mm centers. The Kerfed edge panels shall be then inserted into the H-spline along their long edges of 2400mm against framework to perfect fit with staggered short edges. Technical Parameters: - • Fire (Class) – 1 & P, • Acoustics – NRC 0.87 (For 15mm thk C50 Mounting) • Thermal conductivity (W/mk)– 0.08, • Climate (°C, RH) – 50, 90, • Light reflectance (%) – Low light reflectivity, • Green (VOC, RC %) – Low, 30. Side and Rear Wall Specification Lower Reaches : - Panel 128x2430x16mm, T&G edge-

Supply & installation of Panels made of pinewood E1 grade fiberboard, melamine laminated finish, groove un-perforated slats - (2mm Slats @16mm pitch) / (2mm grooves @ 32mm centers), Non FR, size 128x2430x16mm, volume density of unperforated base board 800Kg/m3, weight 12Kgs/m2 installed by using Strut framework system. Strut framework system includes Strut aluminium core cross channel having thickness 0.55mm, length 3600mm, knurled web 40mm, depth 10mm and equal flanges 15mm is fastened to wall or framework behind vertically / horizontally at every 600mm c/c. Strut aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge &centre brackets is then fixed perpendicular to the Strut Cross channel with the help of fasteners at every 400mm centers. Slats of size 128x 2430x16mm in then fixed perpendicular to Strut CC18 with suitable edge & centre brackets. Short edges of the panel are staggered. Contractor to provide expansion joints of 3mm at every 4.86m length wise and 4.992m width wise. Technical Parameters: - • Acoustics – NRC 0.2, • Thermal conductivity (W/mk)– na, • Climate (°C, RH) – 50, 70, • Light reflectance (%) – 75 (Maple Arce), • Green (VOC, RC %) – Low, 25. Side and Rear Wall Specification Upper Reaches : - Strand 600x2400x20mm, Square edge-

Supply and Installation of Strand , square edge, magnesite- bonded superfine filament pinewood fibre tile of size 600x2400x20mm, density 400 kgs/m3, weight 8 kg/m2 installed by using Strut framework system. The Strut framework systems includes Strut Cross Channel having thickness 0.7mm, length 3600mm, knurled web 40, depth 22mm and equal flanges 15mm is fastened to wall positioned horizontally in a regular manner at 600mm c/c. Strand 600x1200x20mm panels are fastened to Strut Cross channel with suitable fasteners. Longer edges of the panel should be perpendicular to Strut Cross Channel. Fastners to be countersunk and paint finished with suitable colour Factory finish only. The system is backlined with the acoustical infill thermal bonded poly fiber. Technical Parameters: - • Fire (Class) – 1 & P, • Acoustics – NRC 0.91 (For 50mm thk E250* Mounting) • Thermal conductivity (W/mk)– 0.08, • Climate (°C, RH) – 50, 90 • Light reflectance (%) – 75 • Green (VOC, RC %) – Low, 30

Audio System

Supply, installation, testing & Commissioning of Compact Biamplified or triamplified 2/3 Way Line array loudspeaker set with Dual 8" LF drivers, Individual Module Frequency Range of 65 Hz - 18 kHz or better & Continuous Power Handling of >= 450W LF + 100W HF. The Loudspeaker shall have a Max. SPL (Peak) of >=127 dB (LF) and 131dB (MF-HF) or better. It should have Horizontal dispersion pattern of 90º or better, Vertical dispersion of the array shall be 50 degrees or better (at least 02 array modules or more).

Supply, installation, testing & Commissioning of 18" arrayable subwoofer with same footprints as Main Line array elements for Arraying in the frame, having a Freq. Range of 30 Hz - 200Hz. It should have an axial Sensitivity of > = 94dB (1W/1m) or more delivering a free field Max. Calculated SPL(peak) of >=127 db. The loudspeaker should have a nominal impedance: 4ohm or more and continuous Power Handling of 750W or more complete with installation as per the site requirement.

Supply, installation, testing & Commissioning of OEM array frames/ Hanging/ Mounting arrangement for Suspension of upto 16 Full range Array Modules and subwoofers within same array with a safety factor of 8:1 or better.

Supply, installation, testing and commissioning of 8 channel class D Networkable Power amplifier with a Max Output Power of 8x500W@8 ohms, or bridged mode output power of 4x 1000W @ 8/4 ohms. 20Hz - 20 KHz, SNR of 102dB and THD + N of <0.4% with built in protection such as Limiters, Temperature, DC, Short Circuit, Peak Current Limiters, Turn on delay etc. Built in DSP for Matrix routing, Speaker equalization, Delays, Array EQs etc complete with Ethernet Port for Network Control, programming and monitoring. Shall offer optional Network audio connectivity (Dante or CobraNet) through expansion s

Supply, installation, testing and commissioning of Audio Mixer with Analog Mixing Console and 32 mono inputs and four stereo inputs/returns with four groups, main stereo output and a dedicated mono output for centre clusters, 16 inputs suitable for multitrack recording, and six auxes for flexibility, effects and foldback, Complete in all respect as desired by the Engineer in charge of work at site. Make: Soundcraft/Yamaha.

SITC of wireless Lapel microphone, with (UHF) Diversity receiver ,12 Channel Preset or better , Display on Transmitter and Receiver , RF Power output 50mW or Better , Polar Pattern :- Omnidirectional, Carrier frequency range 500Mhz to 865Mhz, Frequency response 45–15kHz, Mute Button on Transmitter, Battery Operation time Minimum 8hr , Should have Charging Contact in Body pack Transmitter, Receiver dynamic range 106dB (A-weighted) switching bandwidth Minimum 40Mhz Or better.

SITC of wireless handheld microphone with (UHF) Diversity receiver ,12 Channel Preset or better , Display on Transmitter and Receiver , RF Power output 50mW or Better , Polar Pattern :- Cardioid , Carrier frequency range 500Mhz to 865Mhz , Frequency response 45–15kHz, Mute Button on Transmitter , Battery Operation time Minimum 8hr , Should have Charging Contact in Transmitter , Receiver dynamic range 106 dB (A-weighted) Or better, switching bandwidth Minimum 40 Mhz Or better.

SITC of Wired Vocal Microphone with On/Off switch, Transducer type: Dynamic, Polar pattern: Cardioid, Frequency response: 50 - 17,000 Hz, Open circuit voltage : 2.4 mV/Pa (-52.5 dBV) ±3 dB, Nominal impedance 600 Ω, Connection: XLR, 3-pin, male, etc. complete with installation as per the site requirement.

SITC of DVD player with HDMI out and USB input

SITC of 4 point mic junction boxes for stage floor, EIC Approved.

SITC of Miscellaneous Adapters, Connectors and other installation material

SITC of Light weight tripod alluminium Microphone stand with Long Arm, boom type & black anodized finish

SITC of Light weight tripod alluminium Microphone stand with short Arm, boom type & black anodized finish

SITC of 2 core 14 AWG/2.5 Sq mm, Twisted, unshielded Speaker cable with stranded annealed bare copper conductors, Semi-rigid PVC insulation, NEC CL3R, CEC CMG, RoHS compliant

SITC of 2 core 12 AWG/4 Sq mm, Twisted, unshielded Speaker cable with stranded annealed bare copper conductors, Semi-rigid PVC insulation, NEC CL3R, CEC CMG, RoHS compliant

SITC of 2 Pair Twisted, shielded balanced microphone Tactical cable with 24AWG or better 40 strand tinned copper conductors, Polyethylene dielectric insulation, 95% tinned copper braided overall shield, Evenly spaced conductors, Super-Flex pressured PVC matte jacket, NEC CM, CEC CM, RoHS compliant

SITC of 4 pair shielded/foiled TIA/EIA-568-C Category 6A cable with 23AWG or better Solid annealed bare copper conductors, High-density polyethylene insulation, Flame rated PVC jacket, Overall aluminum/poly foil shield with drain, NEC CMR, CEC CMR FT4, RoHS compliant.

SITC of 4 pair unshielded TIA/EIA-568-C Category 5e cable with 24AWG or better Solid annealed bare copper conductors, High-density polyethylene insulation, Flame rated PVC jacket, tested to 350 MHz, NEC CMR, CEC CMR FT4, RoHS compliant.

SIITC of 36-42 U Equipment rack with Hardware, Fans, Trays cable managers

SITC of DLP Solid state(Laser Phosphor)having, 8000 Lumens , 4K UHD Resolution, Illumination Life : 20000 hours. Contrast Ratio 2000000:1,Inputs: HDMI, should support 3D at 120Hz. VGA ,DisplayPort, HDBaseT, with lens etc. complete with lens and installation as per the site requirement ., should be complete with mounts and lens

Supply, installation, testing & Commissioning of 220'' Diagonal 4K Resolution Motorised Projection Screen (15.54 feet width x 9.7 feet height )

SITC of Projector mounting kit

SITC of 4K Wall Plate Type Transmitter & Box Receiver for 3xHDMI/USB 2.0

SITC of HDMI 2.0 HDBaseT Extension Set, Extend HDMI 2.0 signals up to 4K@60Hz / 4:4:4 up to 70m (4K 40m / 1080P 70m), Complete set Includes TX, RX, power supply, and IR flasher/emitter, Extends bi-directional IR. Flexible PoC (Power on either end), Supports HDR10, HDCP 2.2 compliant, Flexible power design (use power supply at TX or RX)

Udine Slider – Size: sliding and push back from 22 inch Height : 40 inch from base Arm rest : fome padded Back angel : 14 gauge Seat back density : PU material Cushion ply : tripal layer ply Cushion height : 18 inch from base Back frame ; iron / moulded 15 mm ply Spring for push back sliding :cushion seat,15 kg density with polyurethume Back :About 50 kg density with polyurethume Mechanism : push back 14- 16 gauge push back 15 kg fill welded with powder coating 50x25 Ms Tube of 15 kg using roling spring for push and back with height durability Total weight of chair : 26.5 kg Upholstery : fabric with foam lamination with 5 mm fabric lamination Arm rest handle with cup holder : PPCP injection moulded handle with height durability Installation : will install with existing floor with anchor fastners of length 6" of screws Color : cream fabric

Three seater chrome finish stainless steel chairs with foam back coution.

Folding steel chair with foam coution all complete.

Three Seater Sofas

Make up Chairs

Three seater sofa

Centre table

Wall clock

Gazebo - MFGZ-103 Wicker Gazebo Waterproof metal top Garden pavilion gazebo, 1. Alum. Frame+PE rattan, 2. Hand weaving & colorfast, 3. 2year outdoor warranty, 4. Easy to assemble.

Fountain- 8' dia bublling fountain with chrome finish nosseles all complete.

Supplying and fixing on wall of Painting canvas acrylic handmade with fibre frame

8 Passenger Lift

Madan Lal Bajaj Construction Pvt. Ltd.