Construction of 250MT Capacity cold storage at Veppili Sub Regulated Market in Erode District

Amount

Clearing the Light jungle in working spot as directed by the Departmental officers.

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Extra for every additional One meter lift or part there of over the initial lift

Supplying and filling in foundation and basement with Filling M sand in layers of not more than 15cm thick well watered, rammed and consolidated etc., complete as per standard specification.

Providing and Laying of well gravel in layer laying of 15cm thick using including labour charges of laying and compaction all tools and plants employed etc. complete.

Cement Concrete 1:4:8 (One cement,Four M sand and Eight hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two M sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers) - 50mm thick

Cement Concrete 1:5:10 (One cement, Five M sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers

Damp proof course with Cement Mortar 1:4 (One Cement and Four M sand) 12mm thick mixed with best approved quality water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used and finishing, curing etc. complete complying with standard specification.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require Only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.30 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Cement concrete 1:1-1/2:3 (One cement, one and a half M sand and three hard broken stone jelly) using 20mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc., and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc., shall be finished smooth with Cement Mortar 1:3 (One cement and three M sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers.

For foundation and basement

For Super structure in Ground Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick Work in Cement Mortar 1:5 (One Cement and Five M sand) using Ground moulded Chamber Burnt Bricks IInd class of size 9”x4 3/8”x2 ¾” including curing etc., complete complying with standard specification.

For foundation and basement

For Super structure in Ground Floor

Plastering with Cement Mortar 1:5 (One cement and Five M sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three M sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Providing and painting interior walls & ceiling with two coats of Plastic emulsion paint over one coat of primer including thorough scraping, clean removal of dirt. The rate includes cost of brushes, M sand paper, plaster of parries, putty wherever required and neat finishing etc.,

Providing and painting exterior walls with Two coats of exterior weather proof emulsion paint ove rone coat of primer including thorough scraping, clean removal of dirt. The rate includes cost of brushes, M sand paper, plaster of parries, putty wherever required and neat finishing etc.,

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Vacum dewatering on freshly laid and thoroughly vibrated concrete surface to produce a homogeneous and smooth concrete surface .Suction matshall be spread over the levelled fresh concrete surface and shall be connected by the suction hose to the vaccum pump for dewatering of surplus water in the concrete . After dewatering is complete , the concrete surface is trawled with minimum two passes to achieve a wear resistance concrete surface

Providing Groove cutting in flooring concrete for 10mm width and 20mm depth and filling the groove with combination of Anabond Tuffseald 2G and bitumen tar including cost of all materials and labours etc complete.

Supplying and fixing of rolling shutters with ISI mark shall be of pull and push type made out of 18/Gauge x3’’ lathe sections which consists of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below; Curtain; Shall be of 18/Gx3' lath sections cut to required size and filled with heavy cast iron/ M.S. Clips for 8'0"[2.45m] high rolling shutter lathe sections provided shall be not less than 37 numbers. Lock Plate; Shall be 10gaue M.S.Sheet reinforced with 40mmx 6mm M.S angles at the bottom and fitted with heavy latches of 12mm thick locking arrangements on either sides.

Gear operated type (from 8 m2 to 12 m2 area)

Supplying and fixing of M.S. grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including cutting the members, welding, grinding, one coat of priming coat using best approved quality red oxide primer, dismantling of walls / concrete if necessary, fixing and finishing the dismantled portion to original condition etc., complete complying with standard specification.

Fabricating and supplying and erecting the required number of trusses with structural steel members like MS angle,Tubular sections, channels, MS plates for all truss members including cleats to receive the purlines all cutting drilling holes welding and fixing of members with necessary bolts nuts anchor bolt of approved quality hoisitn aligning and glazing the trusses inposition as per plan. The rate should include the cost painting the members with one coat of red oxide primer and zinc chromate and 2 coats of enamel painting etc., complete complying with standard specification and an directed bya the departmental officers.

Fabricating supplying and erecting the Pre-engineered steel building structure using Galvanised structural steel sections, conforming to Grade 50 with yield strength of 345MPa baseplate, Sag Rods, struts including cleats to receive 'Z' and 'C' purlins, cutting, drilling holes, welding, grinding fixing the members with nessary bolts nuts, anchor bolt of approved quality, hoisting, aligning and placing the 'I' sections in position as per the design got approved from the department, fixing purlins with Sag Rods, supporting the purlins from the beams on both sides. The welding should be done with submerged arc welding to full length. The rate inclusive of the cost of painting the memebers with one coat of primer of Zinc chromite and enamel paint etc., complete complying with standard specification and as directed by the departmental officers, etc., complete.

Double Skin roof sheet Top sheet : Supply & fixing of Colorbond profile sheet of nominal.1072 mm overall width and nominal 28 mm deep ribs with subtle square fluting in the five pan at nominal 203 mm centre-to-centre. The end rib shall be designed for anti- capillary action, to avoid any seepage of water through the lateral overlap. The feed material shall be of (0.45BMT) base metal thickness (0.50 mm Total Coated Thickness (TCT)(0.53 TPT) total painting thickness Hi-Tensile steel with min. 550 Mpa yield strength, metallic hot dip coated with Zinc- Aluminum alloy (55% Aluminum, 45% Zinc) as per AS 1397 – ZINCALUME® AZ150 (Min 150 gms/sq.mt total on both sides) with Super Durable Polyester colorbond steel quality paint system of approved color, suitable for exterior application conforming to AS/NZS 2728 type-4 / IS15965 class 3 . The sheet shall have a total coating thickness of 35 microns, Insulation : Supply & fixing of Rockwool 50mm thick, 64kg/m3 with 0.05 mm thick aluminium foil 1.1mt.wt Bottom sheet : BARE ZINCALUME profile sheet of nominal.1072 mm overall width and nominal 28 mm deep ribs with subtle square fluting in the five pan at nominal 203 mm centre-to- centre. The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap. The feed material shall be of (0.45BMT) base metal thickness (0.50 mm Total Coated Thickness (TCT) Rate including all material, all labour charges,all lead, lift, transportation, taxes etc complete and measured per unit of laid areas.

Single Skin Supply & fixing of Colorbond profile sheet of nominal.1072 mm overall width and nominal 28 mm deep ribs with subtle square fluting in the five pan at nominal 203 mm centre-to-centre. The end rib shall be designed for anti- capillary action, to avoid any seepage of water through the lateral overlap. The feed material shall be of (0.45BMT) base metal thickness (0.50 mm Total Coated Thickness (TCT)(0.53 TPT) total painting thickness Hi-Tensile steel with min. 550 Mpa yield strength, metallic hot dip coated with Zinc- Aluminum alloy (55% Aluminum, 45% Zinc) as per AS 1397 – ZINCALUME® AZ150 (Min 150 gms/sq.mt total on both sides) with Super Durable Polyester colorbond steel quality paint system of approved color, suitable for exterior application conforming to AS/NZS 2728 type-4 / IS15965 class 3 .

Supplying and fixing of Galvolume sheet flashing approved quality with necessary U or J bolts and nuts GI washers etc., complete complying with standarad specification.

Supplying and fixing of profile colour coated Galvalume Eave Gutter of size 217x16.8x154mm made of colour sheet 1.00mm thick with yield strength of 550 MPA of high tensile / C.R. sheets of approved quality for roofing with nessasary fixing arrangemennts with the 'C' purlins provide at the edges 160mm dia rain water downfall pipe etc., complete as directed by the departmental officers.

Supplying and fixing corrugated Poly Carbonate sheet of size 3mx1.06m on the roof inbetween the colour coated Galvolume sheets for propre llighting with nessary scrws and EPDM rubber washers, etc., as complete Complying with standard specification and as directed and specified by the departmental officers.

Supplying and fixing of Gal volume sheet ridge pieces approved quality with necessary U or J bolts and nuts GI washers etc., complete complying with standarad specification

Providing Pre construction of Anti termite Treatment for the Construction of building including all chemicals as per standard specifications. Labour charges for preparing the areas for treatment, spraying chemicals and other incident charges etc.,complete. The rate shall be inclusive of giving anti termite treatment to the building for the following four stages including breaking the termite moulds, making holes with crow bars at an interval of 30 cms to a depth of 50 cms in the pheriphery of building and pouring chemicals etc., complete as per ISI 6313 ( Part 2) 2001. The antitermite chemical chloropyriphos 20 EC used should form 0.5% concentrate for the entire operation etc., as directed by the Engineer in charge and including cost of chemicals labour transportation etc.,

Stage 1: Spraying Anti termite treatment chemical solution for the foundation before laying the foundation concrete at bottom and sides of the foundation.

Stage 2: Spraying Anti termite treatment chemical solution to the grade beam level, spraying has to be done for the grade beam, brick masonry in the super structure in contact with back fill earth.

Stage 3: Spraying Anti termite treatment chemical solution on M sand for the flooring before laying the flooring concrete; the treatment has to be carried out on the M sand filling in basement and after leveling operation is over.

Stage 4: Spraying Anti termite treatment chemical solution around the building on outside by making crow bar holes at an interval of 15 cms to a depth of 30 cms before laying the plinth projection. These holes have to be closed after the treatment.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Making groove of size 25X10mm in plastered tandar the rate shall include necessary labour, scalfllolding, etc to complete as per standard specirfications.

Plastering and finishing of 12mm thick elevation border (upto 100mm wide) with cement motar 1:4 ( one cement four fine M sand) in all heights including edges finishing etc complete., Rate including all materials labour, lead, lift, scaffolding, tax, transportation etc to complete as direction by engineer in-charge.

Providing, applying & finishing 2mm thick self levelling Epoxy Floor Coating over a coat of Epoxy Primer for flooring. ( Epoxy Top Coat application by Combined With Resin and Harner Material to getting desire Color as approved by the engineer incharge).,

Supplying and fixing of PVC prefabricated M sandwich 100mm thick puf panels with rigid puf injected CFC free polyurethane foam as insulation and precoated GI sheet 0.50mm thick on both sides as skin materials and having density of 40 Kg/m3 for wall panels of cold room and precooling room complete as directed by the departmental officials

Supplying and fixing of PVC prefabricated M sandwich 100mm thick puf panels with rigid puf injected CFC free polyurethane foam as insulation and precoated GI sheet 0.50mm thick on both sides as skin materials and having density of 40 Kg/m3 for ceiling panels of cold room and precooling room complete as directed by the departmental officials

Supplying and fixing of PVC prefabricated M sandwich 100mm thick puf panels with rigid puf injected CFC free polyurethane foam as insulation and precoated GI sheet 0.50mm thick on both sides as skin materials and having density of 40 Kg/m3 with vapour matt for flooring panels of cold room and precooling room complete as directed by the departmental officials

Supplying and fixing of Main Sliding Door size 2400x3000x80mm with manual opening anti condensate self limiting, regulating energy saving door, Human safety door release, Heavy duty latches for cold room with necessary locking arrangements complete as directed by the departmental officials

Supplying and fixing of pvc strip curtain Suitable for Cold room door complete

Supplying and fixing of 6 feet Air curtain Suitable for Cold room door complete

Supplying and fixing 100 mm puf panels accessaries and flashing complete

Supplying and fixing vapour proof 22W LED moister proof light fiiting complete (or) IP65 rating LED focus light.

BLUELEAF PROJECTS PRIVATE LIMITED