Construction of building for Brahmaputra Studies Centre at Gauhati University campus

Amount

CIVIL WORKS

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. A) Up to a depth of 2.00m below the existing ground level. a) In ordinary soil

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. a) With earth or silt or sand obtained by head load with lead upto 90m and lift upto 2m

(c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

CEMENT CONCRETE WORKS - PLAIN CEMENT CONCRETE WORKS Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). a) In prop 1cement: 3 sand :6 coarse aggregate by volume

REINFORCED CEMENT CONCRETE WORKS Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) II. Using Batching Plant/ RMC/ Truck mounted batching plant including Transit Mixer and Concrete Pump e)M35 grade concrete

Extra for using plasticiser in concrete if admixture, plasticiser etc are not included in the item rate e) M35 grade concrete

SHUTTERING , FORMWORKS TIMBER SHUTTERING (FORMWORK) Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. (b) Using 25mm thick plank

Sides of tie beams, grade beams etc. at or below ground level. (b) Using 25mm thick plank

PLYBOARD SHUTTERING (FORMWORK) Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face Ground Floor

First Floor

Second Floor

Terrace / Third Floor

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. a) For depth not exceeding 1.0M. Ground Floor

First Floor

Second Floor

Third / Terrace floor

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness. Ground Floor

First Floor

Second Floor

Third / Terrace floor

Vertical surface such as walls (any thickness), parapet walls, partitions and the like including attached pilasters, butresses, plinth and string courses and the like. Ground Floor

First Floor

Second Floor

Vertical ties, fins, sun breaker, louvers, bands, dropwalls etc. Ground Floor

First Floor

Second Floor

Staircase with sloping or stepped soffits including risers and stringers but excluding Landing. Ground Floor

First Floor

Second Floor

MASONRY WORKS Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete : 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rateincludes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/200/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

FLOORING AND FLOOR FINISHING Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) a) Normal range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make ii) Of size 600mmx600mm and above

b) Executive range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make i) Of size 800mmx800mm and above

c) Delux range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make i) Of size 1000mmx1000mm and above

c) Delux range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make ii) Of size 1200mmx1600mm and above

Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). iii) Of size300mmx600mm and above

Providing polished granite slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). (i) Executive Quality (ii) With White cement

(iii) Deluxe Quality (ii) With White cement

Base mortor extra Plaster area for the above work

TERRAZO FLOORING 40 mm thick marble chips flooring rubbed and polished to granolithic finish with under layer of 32 mm thick cement concrete in prop. 1:2:4 (1 cement:2coarse sand:4 graded stone aggregate of 10 mm and down graded) and top layer 8 mm thick with marble chips of any colour or combination of colours and 1 mm to 4 mm nominal sizes laid in cement marble powder mix 3:1 (3 cement:1marble powder by weight) in proportion 4:7 (4cement marble powder mix :7 marble chips by volume ) including providing cement slurry including curing etc. complete. (b) Pigment of any light shade with white cement in top layer

PAVER Providing SUN ROCK HIGH CTS/DEVI paver block/tiles of concerete grade M30 or above of approved quality size, shape of specified thikness over a labelling bedding layer of 30mm compacted sand over a base course of WBM or PCC (Base course to be paid separately) including cutting where necessary finished with spreading, sweeping, jointing sand and com[action the paver using vibrating compactor as specified and directed SUN ROCK HIGH CTS/DEVI paver d) 40 mm thick

Providing Polished granite tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). (ii) With White cement

VINYL FLOORProviding & installing of Homogenous Vinyl flooring of Approved make as per manufacture specification over finished flooring surface. Supplying and fixing Imported Anti-static Vinyl flooring with HOMOGENEOUS FLEXIBLE vinyl rolls of approved make & shade 2mm thick of standard sizes as per IS:3462 / BS:3261 of manufacturers specification over the existing floor. The rate shall include all cuttings and wastages, cutting and providing tile above electrical trunking, cost of all materials including skirting with edge capping to the approved patterns to be fixed over rcc and masonary surfaces, pvc coving, adhesives of SR-505 FEVICOL of M/s.PIDILITE Industries Ltd., make etc; including welding of joints, complete. Only laid area will be measured for payment. Rate quoted shall be for the complete finished work including all the materials and labour mentioned above. (basic cost Rs.1250/Sqm).

40 mm thick cement concrete floor consisting of 25 mm under layer of cement concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 12.5 mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse aggregate of size 10mm down) finished with a floating coat of neat cement finish using cement slurry for bond @ 2.75 kg. per square metre of floor area , wearing layer is to be laid in panels including curing etc. complete as directed.

PLASTERING WORKS 10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. a) In cement mortar 1:3 Ground Floor Ceiling Plastering

First Floor Ceiling Plastering

Second Floor Ceiling

Terrace floor ceiling

Sunshade plastering GF

Sunshade plastering FF

Sunshade plastering SF

Sunshade plastering TF

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side b) In cement mortar 1:4 Ground Floor inside wall plastering

First Floor inside wall plastering

Second Floor inside wall plastering

Third Floor inside wall plastering

Extra over item no 6.2.1 to 6.2.3 for providing and mixing water proofing materials in cement mortar in prop as recommended by the manufacturer including curing complete as directed. Ground Floor inside wall plastering

First Floor inside wall plastering

Second Floor inside wall plastering

20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. A) On rough side (backing coat 15 mm and finishing coat 5mm thick) c) In cement mortar 1:5 Ground Floor external wall plastering

First Floor external wall plastering

Second Floor external wall plastering

Third Floor inside external plastering

ROOFING & ROOF TREATMENT Providing and fixing of leak proof,fire retardant and Uv resistant skylighting galzing with Lexan polycarbonate sheet fixed with specially designed Domal management system confirming to IS:737 alloy & temper 6063 - T6 with a UTS of 180 to 200 mpa and weight of 1.03 kg/mtr. approx with EPDM rubber gasket of specific gravity as per ISO 2781,age resistant as per ASTM - D573 hardness as per 2240 & tensile strength as per ASTM 412 including the silicon sealent GE Bayer Weathersil NY as per drawing and directed by the Engineer in charge. (b) Polycarbonate Sheet (Multiwall) (iii) 10 mm thick

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including

Metal Fin: Designing, providing & fixing the Aluminium PVDF finished of approved colour and perforated (as per the drawing) metal Fin of 75 to 100 mm wide with thickness not less than 5mm thick. Thickness of coating shall be not less than 30 microns. Aluminium fin to be fixed in to the glazing mullion by using continuous aluminium extruded PVDF finished bracket (Thickness not less than 5.0mm) with SS 316 fasteners, bolts & nuts & sealant and as per drawing. Rate shall include the cost of all materials, accessories etc complete. System to be designed to with stand design wind pressure of 150Kg/Sqm confirming to IS 875 part 3 and other load parameters specified in Technical specification. Refer Particular Specification Item. No. 22.01.

WOOD WORKS: WOODEN FLUSH DOOR WITH ALEXA SYSTEM-100 FRAME PROFILES Supply & Fixing of Wooden/Flush Door (Single Leaf) of 40mm thick with DORMA Alexa System-100 X25mm frames all around the door. Alexa DP100-DG WD Door Profile frame with seals with DORMA Hinges (3Nos) & Pure 8998 Lever Handle 271 Lock package/TGDI H350 Pull Handle 278 Dead Lock package and DORMA TS 89 Slide Channel Door closer with (as per EN 1154) necessary seals to be provided all around the door frames. In case of Glass overall panel Alexa OHPDP100-DG Over Panel Door profile to be used. The Alexa profiles shall be suitable for Wooden/Flush Door thickness upto 45mm.The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing. Approved Manufacturer: Profiles/Frames: DORMA, Glass : Saint Giobain/Asahi

Providing, fitting and fixing factory made Santro Flush door shutters having core & cross bands fabricated from seasoned 1st class timber, 25mm core battens, 2.5mm to 3.5mm uniformly thick cross bands, styles & rails made from hardwood timber of width not less than 50mm, fixed to the door frames (chowkath) with necessary hinges, screws, bolts etc. as specified and directed at all levels (Door fixtures and fittings to be measured and paid seperately.) (b) 35mm thick

Aluminum Frame made of 10mm X45mm X2.5mm section of approved brand (HINDALCO/NALCO/BALCO/JINDAL/Other equivalent primary producer) ,Hardwares (pivot, tower bolt, aluminium door handle, lock angle, cleat etc.), vision glass for the above doors

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix,suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc.complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of60 minutes fire rating conforming to IS:3614 (Part-II), tested and certifiedas per laboratory approved by Engineer-in-charge, with suitable mounting wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete

Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ openingwith M.S. flats at required spacing in frame all round, squre or round M.S. bars with round headed bolts and nuts or screws. I . Plain grill (c) Fixed to Brickwork/P.C.C/R.C.C.

Supplying and installing uPVC- sliding door made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC multichambered sections of wall thickness 2.8mm with corners fusion welded, fully reinforced with Galvanized steel 2mm including interlock profile, glazing bead, grooving bead, brush seal, locking arrangement, aluminum sliding track, stainless steel rollers, sealing wedge block, Espag, int handle, pop up handle, keeper, drain cap, fisher screws, packing pieces with all necessary stainlessness screws etc. complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers and with suitable water draining system. Fittings ROTO / GQ or Equivalent. Application of silicon sealant from inside / outside of Dowcorning / GE or equivalent. (I) 2 Track Sliding door with Flyscreen using uPVC section of size 88mm x 50mm x 2.8mm thick wall for frame, 37mm x 75mm x 2.8mm thick wall for glass sash, 25mm x 49mm x 2.8mm thick wall for flyscreen sash, Interlock: 43mm x 23mm (Glass Panel) (WINSTA KOMMERLING/ FINESTA/ ENCRAFT) ii) Using 5mm clear toughened glass

Supplying and installing uPVC- Casement Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC sections of wall thickness 2.4mm, multichambered with corners fusion welded, fully reinforced with Galvanized steel 1.5/2mm including glazing bead, folding gasket, glazing gasket, friction stay, Espag handle, Espag, keeper, drain cap, run up block, fisher screws, packing pieces with all stainless steel screws complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets,bridging wedges and glass packers and with suitable water draining system. Fittings ROTO / GQ or Equivalent. Application of Silicon sealant from Inside / Outside of Dowcorning / GE or equivalent. b) Double leaf Side hung Window with a fixed Mullion (2 Panels) using uPVC profile size of 58mm x 57mm x 2.4mm thick wall for frame, 58mm x 68mm x 2.4mm thick wall for glass sash, 58mm x 74mm x 2.4mm thick for mullion. With 5mm clear float glass

Supplying and installing uPVC- Fixed Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC multichambered sections of wall thickness 2.4mm with corners fusion welded, fully reinforced with galvanized steel 1.5/2mm including glazing bead , grooving bead, drain cap, fisher screws, packing pieces, necessary stainless steel screws etc. complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers and with suitable water draining system. Application of Silicon sealant from inside / outside of dowcorning / GE or equivalent. With 5mm clear glass (a) Fixed window using uPVC sections of size 58mm x 52mm x 2.4mm thick wall for frame and 58mm x 68mm having 2.4mm thick wall for glass sash having reinforcement of 1.5mm thick in both frame & sash. (WINSTA KOMMERLING/ FINESTA/ ENCRAFT)

(f) ProVent openable Top hung Window using uPVC section of size 37mm x 43mm x 2.2mm thick wall for frame, 37mm x 56mm x 2.2mm thick wall for glass sash With 5mm clear float glass (WINSTA KOMMERLING/ FINESTA/ ENCRAFT)

PAINTING WORKS: Providing two coats of acrylic water based wall putty/ wall filler of Asian Paints/ Berger/ Dulux over concrete/ cement plaster/ brick walls and ceilings both internal and external after removing all the loosely adhering material from the wall/ ceiling surface with the help of emery stone, putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department. For ceiling and inside walls

Wall painting (two coats) with acrylic emulsion paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Extra over item no 13.4.1 above for every subsequent coat of wall painting with acrylic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac). (i).Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Extra over item no 13.4.1 above for painting with acrylic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on celling and on sloping roof. (i).Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

EXTERIOR PAINTS / COATINGS:Applying one self-priming coat of acrylic emulsion coating of Unicem "Rakshak" brand by thinning 1ltrs of paints with 1ltrs of water over freshly plastered wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth as specified and directed by the department. c) Asian paint/Berger paint/ICIJ&n/Nerolac

Finishing wall with two coats of acrylic emulsion exterior coatings of Unicem "Rakshak" brand of required shade by thinning 1ltr. of paint with 750ml of water to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials as specified and directed by the department. c) Asian paint/Berger paint/ICIJ&n/Nerolac

PAINTING ON STEEL AND OTHER METAL SURFACE Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. a). With ready mixed "red-lead/ red oxide" primer.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (i).Surfaces over 100mm in width or girth. a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

REINFORCEMENT Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (ii)Super Ductile (SD) TMT reinforcement bars Ground Floor

First Floor

Second Floor

Third / Terrace floor

ROLLING SHUTTER Providing and fixing in position collapsible M.S. shutters with vertical channels 20mmx10mmx2mm braced with flat iron diagonals 20mmx5mm size with top and bottom rails of T-iron 40mmx40mmx6mm with 38mm dia steel pulleys complete with bolts and nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any two or all of the following sections (i) Square section (ii) Rectangular Hollow section of specification RSH/SHS and (iii) M.S. circular hlollow section of Grade 210 including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S. code 4923 : 1997

Steel support for STRUCTURAL GLAZING system

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixingrequired door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately).

STURCTURAL GLAZING SYSTEM Semi unitized glazing system with Vision, Vision on Spandrel panel (System with Segmented Glass): Designing, providing and fixing Semi Unitized structural glazing vision panel & vision on spandrel panel structurally held in position by Structural sealant and factory fabricated with Aluminium adaptor of suitable size in order to satisfy the structural design criteria specified in the Technical specification. In general, the system comprising Aluminium anodized extruded frames confirming to IS 8147 and anodizing AC 25 grade confirming to IS 1868 & Adapters supported on the brackets (spanning 3.0 to 3.2 M), Toggle cleats, HDG brackets & SS anchors and bolts, flashing etc having with Insulated glass of 24 mm thick having 6 mm thick Reflective coated low E glass on # 2 surface with SKN 754 of Saint Gobain make or Solarban 70 XL(2) Solar blue of PPG make or Excel 40 Blue Pearl of Asahi make as outer pane and 12 mm airgap and 6 mm thick glass uncoated clear as inner pane of same make. Both panes are shall be heat strengthened. Rate shall exclude the cost of supply of top hung window hardwares and insulation, which will be measured and paid separately under the respective item below. Rate shall include the cost of supplying & fixing of glass, fixing of Top hung window hardwares, Offsite proto type test, visual mock up and field water test etc. System to be designed to with stand design wind pressure of 150Kg/Sqm confirming to IS 875 part 3 and other load parameters as per specifications

PILE TEST Routine test for test loading to 1.5 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load) for 500mm dia pile

Routine test for test loading to 1.5 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load) for 600mm dia pile

Initial test for (500mm dia pile capacity 36 ton) test loading to 2 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Initial test for (600mm dia pile capacity 44 ton) test loading to 2 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Integrity testing of pipe using low stain/sonic integrity test/sonic Eco test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud dust and shipping lean concrete lumps etc. and use of computerised equipments and high skilled trained personnel for conduction the test and submission of results, all complete as per direction of engineer

PILING WORKS MACHINE DRIVEN PILES Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.5.1) C) UNIFORM PILE - iii) Concrete Grade M30 i) Pile dia 500 mm

iii) Pile dia 600 mm

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) (A) TMT bar made of Primary producer (From Primary producer)

WATERPROOF SURFACE PREPARATION Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels.

WATER PROOFING OF CHAJJAS, ROOF SLABS, TERRACES, SUNKEN SLABS, SEPTIC TANK,OH TANK, RAFT SLAB IN BASEMENT, WALLS ETC. (A) Supplying, mixing, laying and applying the following waterproofing systems over Raft slabs, Roof slabs, Terraces etc. including curing complete as specified and directed by the Department at all levels.: (i) 1mm thick single coat of Master Crete M-81 of Choksey Chemicals /Dr. Sealkit Sealcrete (Asian Chemicals)/ mixed with cement in the ratio 1:2 as a prime coat. (ii) 3mm thick Polymer modified mortar - Cement sand mortar (in prop 1:3) mixed with Master Crete M-81/Dr. Sealkit Sealcrete (Asian Chemicals) @ 15% by weight of cement. (iii) 1mm thick coat of Master Crete M-81 /Dr. Sealkit Sealcrete (Asian Chemicals) mixed with cement in the ratio 1:2 as final coat. (B) Using RHEOMIX 131 OF BASF

Supplying, providing, mixing and laying over waterproofing layers/ coatings with concrete screed of average 30mm thick or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with 10mm and down well graded aggregates and admixed with a normal plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department.

Providing, supplying, mixing, laying 8mm thick cement Plastering in prop.1:6 over R.C.C. surfaces mixed with integral waterproofing compounds like Master Proof IWP-1 of Choksey Chemicals /Dr. Sealkit No.1 (Asian Chemicals) /Rheomac 707 of BASF@ 0.2% by weight of cement conforming to IS:2465 as specified and directed by the Department complete.

Providing, supplying, mixing and champhering the edges along joint of wall/ parapet wall and raft/ roof slab having champhered dimension of 150mm x 150mm with cement sand mortar (prop.1:4) mixed with Master Proof IWP-1 of Choksey Chemicals /Dr. Sealkit No. 1 of (Asian Chemicals)/ RHEOMAC 707 of BASF@ 0.2% by weight of cement over a primer coat on the area to be champhered with a combination of 100% acrylic Polymer Master Crete M-81/Dr. Sealkit Sealcrete (Asian Chemicals)/ RHEOMAC 115 of BASF of Choksey Chemicals and cement in the ratio 1:2 to be applied by brush as specified & directed by the Department complete.

ANTI TERMITE TREATMENT Pre construction anti - termite treatment at the bottom of foundation pits and walls on either side up to a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches etc. by applying the emulsion @ 5 (five) litres per square meter of the surface area before starting construction work (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

Pre construction anti - termite treatment in the back fill in immediate contact with the foundation structure after completion, column, wall etc. to a depth of 450mm and width 300mm (when required refill in 200mm thick layers) applying the emulsion @ 5 (five) litres per square meter towards the concrete and masonry walls so as to ensure earth in contact with the structure well treated - with chemical (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

HANDRAILS Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Supplying and fixing Terracotta clay Jolly

sunken filling Toilets Supplying and filling the sunken slab area by BRICK-BATCOBA by adding CICO NO:1 or approved equivalent admixture at the rate specified in the manufacturer's specification after entire completion of laying pipes, sanitary fittings etc. Rate shall include for preparation of surface, protecting the laid pipes and sanitary fittings, finishing the surface smooth to receive the top coat of water proofing application etc. complete and all as directed.

Providing and fixing PVC (6 Kg/sqcm class) pipe of specified dia below and approved make as water down take pipe with all specials, accessories and joints with solvent cement solution according to manufacturer’s specification. 200 mm dia

160 mm dia

110 mm dia

Single /Double leaf to required sizes and approved make shakti met-dor or equivalent which consists of frame, shutter, infill and finish as detailed below and conforming to IS 277. Door frame shall be single rebate profile of size 100 x 57 mm made out of 1.20mm minimum thick galvanized steel sheet (18 gauge ). Frames should be mitered and field assembled with self tabs. Door frames should be prepared for suitable hardware as scheduled and should have necessary reinforcement to withstand regular wear and tear. All provision should be mortised, drilled and tapped for receiving the hardware. Rubber door silencers should be provided on the striking jamb. All door frames should be provided with backplate and anchor fasteners for installation on a finished plastered masonry wall opening. Once the frame is installed it should be grouted with cement & sand slurry. Door leaf should be 46mm thick flush double skin door with vision panel of suitable size. Door leaf shall be manufactured from 0.8mm (22 guage) minimum thick galvanised steel sheet. The internal construction of the door should be rigid with steel stiffeners/ pads and reinforcement. The infill material shall be resin bonded honeycomb core.(Contd.)

All doors should be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, shaft locks, flush pull and tower bolt etc. The edges should be interlocked with lock seam. For pair of doors astragals will be provided as required. 450x750mm Vision lite wherever applicable should be of size fixed with rubber beeding. The glass should be 4mm clear toughned glass. All doors and frames shall be finished with polyurethane aliphatic grade powder coating minimum of 50 microns of approved colour. The door leaf and frame shall have passed minimum 500 hours of salt sprey test. Rate should include supply and installation of door and hardware as a complete assembly as mentioned in the door and hardware schedule. Steel DoorSD Single leaf 600x1500mm without vision panel with frame on Four sides & hardware set Hinges BB 4330, 5 Knl, 2 Ball bearing butt hinges size 4" x 3" x 3mm SS 304 Mortice Shaft Dead lock with Allen key 8681, SSS Flush Pull Handle 1208, OVAL, SSS

Steel Door SD 1 Single leaf 750x1500mm with 450x750mm vision panel with frame on Four sides & hardware set Mortice Shaft Dead lock with Allen key 8681, SSS

Steel Door SD 2 Single leaf 1200x1500mm with frame on Four sides & hardware set

Providing and fixing Modular Toilet Cubicals with the following speicifications MODLE TYPE - MERINO TITAN STANDARD SERIES (2100mm HEIGHT) or Equivalent Thickness of Compact Laminate : 12 mm Thickness of Compact Laminate : 12 mm Color of HPL Boards: As per Merino Cubicle Shade Card Size of Cubicle : As per drawing Overall Height Of Cubicle : 2100 mm (Including bottom Gap of 130mm) Accessories: Standard – Merino Make Stainless Steel - 304 Grade accessories)

SANITARY AND PLUMBING

Providing fitting and fixing Vitreous china wall hang water closet (European type W.C pan 400mm high) with seat and lead , P Trap , CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) a) Parryware make (i) Pal Walvit Pan (inclusive of seat cover and fittings) (white/coloured) (Cat. No. C844K)

Supplying, fiting and fixing concealed cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) A) Parryware make (i) Rios with Chorme Push Plate (Cat no.8174/ Cat. No.C813726)

urinal Providing fitting and fixing vitreous china flat back type lipped front urinal basin of with automatic flushing cistern with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. A) Parryware make a) White (i) Integrated EFS-Smart DC (Cat No.C8182) / Integrated EFS-Smart AC with power source (Cat No.C8195)

Supplying fiting and fixing glass division plate of Jaquar make including fitting and fixing compete as directed and specified.

Wash Basin Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) (A) Parryware Make (i) Chester 550 x 445 (Cat. No.C8469) (white/coloured)

KITCHEN SINK (STAINLESS STEEL) Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately (B) Nirali (i) Glister Jumbo (Bowl Size - 610 x 460 x 254) Glossy

MIRROR Providing fitting and fixing Decorative Mirror complete as directed and specified. (A) Parryware Make (a) Size 800mm x 600mm

(a) Double Arm Wall Mounted reversible plain / Magnifying (3X) Pivotal Mirror (Cat. No.ACN-1193N)

SHELF Providing fitting and fixing Glass Shelf complete as directed and specified. Glass shelf with C.P. guard rail (i) Agmeco make (a) Cubin (Cat. No.SQ-00104)

(iii) Jaquar make (a) Continental 550 mm long (Cat. No.ACN-1171N)

Providing, fitting and fixing CP soap tray / soap dish complete as directed and specified. (i) Jaquar Make (a) Continental (Cat.No.ACN-1331N)

Providing, fitting and fixing Liquid soap dispenser and liquid soap container complete as directed and specified. (ii) Agmeco Make (a) Liquid soap container Capsule Type (Cat.No.LSC-0001)

Providing, fitting and fixing CP towel rail complete as directed and specified. (a) Jaquar make (ii) Continental 600mm (Cat.No. ACN-1111N)

Providing, fitting and fixing Chrome Plated towel rack complete as directed and specified. (i) Continental 600mm long with hanger (Cat.No. ACN-1181N)

Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified. (a) Jaquar make (i) Continental towel ring square (Cat.No. ACN-1121)

Providing, fitting and fixing Chrome Plated robe hook complete as directed and specified. (a) Jaquar make (i) Continental (Cat.No. ACN-1191N)

Providing, fitting and fixing Chrome Plated tumbler holder complete as directed and specified. (a) Jaquar make (i) Continental (Cat.No. ACN-1141N)

TOILET PAPER HOLDER Providing, fitting and fixing Chrome Plated TOILET PAPER holder complete as directed and specified. (a) Jaquar make (ii) Continental toilet paper holder with flap (Cat.No. ACN-1153N)

Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified. (i) 32mm (HT/FT) (Cat.No.ALD-705 / 709)

Providing, fitting and fixing Chrome Plated bottle trap complete as directed and specified. (a) Jaquar make (ii) Bottle trap (with internal partition) 32mm size with 300mm long wall connection pipe (Cat.No. ALD-769B)

Supply, Installation, Testing & Commissioning of Divertor- Grohe make single lever concealed Bath Shower mixer (diverter). Crome plated (CP) both overhead shower and spout option. Grohe BauFlow Cat no-29065000

Supplying fitting and fixing Chrome Plated (C.P.) shower 15mm dia. Of approved brand as directed and specified. (Pipes will be measured and paid separately) VI) Grohe make: Bau over head shower with arm 3 adjustable spreys with wall flenge Cat No- 27398000 (i) Shower arm light casted with wall flange

Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as C9directed and specified. (G.I. & C.P pipes will be measured and paid separately) Jaquar brand a) Continental / Clarion i) Sink cock with swinging casted spout

BIB COCK Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) (c) Two way long body bib cock with wall flange

PIPES Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and specified. (Note: Ball valve and union will be charged extra and does not comes under Accessories) Concealed by chiselling or breaking brick wall /CC/R.C.C and making good to damages. (b) 20 mm OD

(c) 25 mm OD

(d) 32 mm OD

Providing and fixing Chlorinated Polyvinyle Chloride (CPVC) Pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipe (A) Exposed or in trenches a) 32 mm nominal outer dia pipe

a) 40 mm nominal outer dia pipe

b) 50 mm nominal outer dia pipe

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. i)50mm diameter

iii)75mm diameter

v)110mm diameter

a)In exposed surfaces or in trenches. i)110mm diameter

(ii) 160mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm

(ii) 110mm dia.

(iv) 75 mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

(iv) 75 mm dia.

(v) 50mm dia

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

(iv) 75 mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

(iv) 75 mm dia.

(v) 50mm dia

Supplying fiting and fixing 45degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

(iv) 75 mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

(iv) 75 mm dia.

(v) 50mm dia

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

(iv) 75 mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

(iv) 75 mm dia.

(v) 50mm dia

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

(iv) 75 mm dia.

Supplying fiting and fixing PVC single ‘Y’ of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia

(ii) 110mm dia.

(iv) 75 mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

(iv) 75 mm dia.

(v) 50mm dia

Supplying fiting and fixing PVC single ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm dia.

(ii) 75 mm dia.

Supplying fiting and fixing PVC coupler of (Supreme / Prince)or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110 mm dia

(iii) 75 mm dia

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (i) 110 mm dia

(iii) 75 mm dia

COWEL Providing fitting and fixing 50mm dia. HCI cowel with cement caulking complete as directed and specified.

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. (i) 160mm dia. PVC cowel of ISI make

(ii) 110mm dia. PVC cowel of ISI make

(iv) 75mm dia. PVC cowel of ISI make

GRATING Providing fiting & fixing (300x230)mm C.I. yard gully hinged Grating complete as directed and specified.

C.P. Grating (ii) 110mm dia

STOP COCK Supplying fitting and fixing stop-cock of approved brand of size as mentioned below and directed and specified (G.I. & C.P. pipes will be measured and paid separately) I) Brass stop cock (heavy) of Sant make (i)15mm dia

Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) (i) Angular stop cock with wall flange

Organic Waste Disposal System 3HP single Phase vertical multistage high pressure centrifugal pump set 8 stage (Crompton Greaves/Aquatic/CRI/V-Guard make) 2900 rpm with DOL Starter (Crompton Greaves/Control & Switch Gear/BCH/L&T / Siemens make0. - For Domestic water transfer pump

2 HP single Phase jet monoblock two stage pump set(Crompton Greaves/Aquatic/CRI/V-Guard/Calma make) 2900 rpm with DOL Starter (Crompton Greaves/Control &Switch Gear/BCH/L&T/Siemens make).

VALVE Supplying and fitting ball valve as specified and directed. a) 25 mm dia. (gun metal)

b) 20mm dia. (gun metal/Copper)

Supply, fixing of CP press matic pillar cock for wash basin with necessary accessories complete all. Make . Jaquar / Hindware/ Greha

Valves Supply and fixing of gun metal ball valve with complete accessories all. a) 50 mm

Supply and fixing of auto release urinal matic wash basin piller cock with necessary flanges complete all.

Providing, fixing, testing and commissioning of PVC multi inlet floor trap of self cleansing design moulded or fabricated, if not available in size mentioned below, with or without vent arm arm jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste including making good the floors. 110mm dia inlet 75mm dia out let

Providing, fixing, testing and commissioning of stoneware gully trap (ISI brand only) of 150 x 150 mm size with 100 mm dia outlet making excavation pit in all kinds of soil excluding soft rock and hard rock to a size of 600 x 600 mm and laying of 100 mm thick 1:4:8 mix cement concrete bed and constructing chamber with internal clear dimension of 300 x 300 mm using brick work 115 mm thick in cement mortar 1:6 up to a height of 300 mm above gully trap or up to 100 mm above paving level, plastering internal and external surface with cement mortar 1:4 to 15m thick finishing to smooth inside surface with necessary benching and channeling providing 150 x 150 mm size cast iron grating, including 40 mm thick precast RCC cover slab, clearing the surplus material, earth etc. complete. Notes: Rate is excluding for earthwork and backfilling. It shall be measured separate and paid for. 150mm x 150mm size `P/S' trap

Rain water harvesting recharge pit with necessary 160 mm dia bore hole pipe with necessary pebbels, grating complete all.

Providing and fixing Constructing storm water catch basin internal clear dimension as mentioned below with 230 mm thick brick masonry wall using 1st class table moulded brick in 1:4 over a bed of 150 mm thick 1:4:8 PCC in cement motar 1:5 (1cement: 5 fine sand), precast perforated RCC top slab in 1:2:4 Mix (1 cement: 2 coarse sand: 8 graded stone aggregate),with angle iron frame, inside plastring 15 mm thick with CM 1:3 (1cement: 3 fine sand) finished very smooth with floating coat of neat cement & making channel in (1cement: 2 coarse sand: 4 gradedstone aggregate) neatly finished complete as per standard design and as per drawing. (The rate shall include necessary earth work excavation in all types of soil excluding soft and hard rock, back filling including consolidation disposing the excess earth to all leads curing, finishing etc., and back filling and completion) Inside size of 600 x 600mm & depth not exceeding 900mm including providing 600 x 450mm precast perforated RCC cover with 50 x 50 x 6mm thick with MS L angle frame.

Supply and fixing of water meter of 50mm dia to measure the water quantity including the sifing support and gasket flanges.

Constructing grease trap chambers in 230mm thick brick masonary in cement mortar 1:5. Clear internal dimensions 1500mm x 900mm constructed over a hed of cement concrete 1:3:6, 150 thick 1/2 no. hanging baffle in in 50mm thick RCC of suitable size, aluminium perforated tray of size 500 x 400 x 150 (deep) fabricated out of 14 gauge sheet, with 40mm wide top flange supported on all four sides with 40 x 40 MS angle fixed to wall Anchor fasteners plastering inside, outside and bottomof bitumastic paint etc., complete, depth of chamber not exceeding bottom of chamber with cement mortar 1:3, providing and fixing one No. CI frame & cover size 900 x 600 weighing not less than, 125 K gms and another frame and cover size 600 x 600 weighing not less than frame and cover size 600 x 600 weighing not less than 75 Kgms providing CI steps at 300mm C/C, vertically at two corners of chamber, painting all CI items and MS items with two coats of bitumastic paint etc., complete, depth of chamber not exceeding 1200mm.

Construction of brick masonry inspection chambers of internal clear dimension as mentioned below by using first class table moulded modular bricks 230 mm thick wall in cement mortor joints in 1:4, over CC 1:4:8 bed 150 mm thick including providing precast RCC top slab in 1:2:4 Mix (1 cement: 2 oarse sand: 8 graded stone aggregate), with angle iron frame, inside plastering 15mm thick with CM 1:3 (1 cement::3 fine sand) finished very smooth with floating coat of neat cement & making benching and channelling in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 gradedstone aggregate) neatly finished complete as per standard design and as per drawing and specifications. (The rate shall include necessary earth work excavation in all types of soil excluding soft and hard rock, back filling including consolidation disposing the excess earth to all leads curing, finishing etc., and back filling and completion) Inside size of 900 x 900mm & depth not exceeding 1500mm including providing 600 x 600mm RCC cover.

1400mm dia circular manhole with 560mm dia RCC cover for depth above 1500.

Supply and fixing of MS grating with FRP Paint of 300 X 300 mm with necessary fixng accessoires complete all.

Supplying and Erection PVC Floor Clean Out Dia 110mm to125mm and depth of 150mm to 300mm, Inlet 40mm to 90mm and outlet 75mm to 90mm dia Made of PVC Make making holes, cutting the surfaces, laying cement concrete in 1:2:4 mix with 20mm stone jelly, restoring the damaged portions to their original condition, providing and Erection square shape

Supply, installation, testing and commissioning of pressure booster pump with necessary pressure tank, pump, limit switch, pressure gauge complete all.-Maximum pressure of remotest point is 3.5 kgs. -1000 liters per minit

ELECTRICAL WORKS

Wiring to 5 a pin Amps plug point with 1.5 s. mm. P.V.C. insulated single core unsheathed industrtial (Multistrand)cable FR conforming to IS- 694:1990 with flexiable bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/(RR cable or Euivalent Make as approved by the Deptt.)in surface /recessed ISI marked steel conduit pipe (AKG or euivalent as approved by the Deptt .) wiring system including 5 pin 6 Amps flush type plug socket and 6 Amps F/ T switch (Anchor penta /Gold medal / color kany.com /Havell or euivalent make as approved by the Deptt.) GI/ MS switch board (I.S.I. marked) with phenolic laminated sheet cover including earth continuity with 1.5 s.mm. cable to third pin of the plug socket etc. as reuired complete, when placed elsewhere. a) Short point up to 3.00 metre.Length.

b) Medium point up to 6.00 metre.Length.

Wiring to 5/6 pin16 Amps plug point with 4s. mm. P.V.C. insulated single core unsheathed industrtial (Multistrand)cable FR conforming to IS- 694:1990 with flexiable bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/(RR cable or Euivalent Make as approved by the Deptt.)in surface /recessed ISI marked steel conduit pipe 20mm. dia. (AKG or euivalent as approved by the Deptt .) wiring system including and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps F/ T switch (Anchor penta /Gold medal / color kany.com /Havell or euivalent make as approved by the Deptt.) make), GI/ MS switch board (I.S.I. marked) with phenolic laminated sheet cover including earth continuity with 2.5 s.mm. cable to third pin of the plug socket etc. as reuired complete. a) Extra long point up to 15.00 metre. Length.

b) Extra long point up to 20.00 metre . Length.

Wiring for drawing sub -main line with P.V.C. insulated single core unsheathed industrtial (Multistrand)cable FR conforming to IS- 694:1990 with flexiable bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/(RR cable or Euivalent Make as approved by the Deptt.) ISI marked steel conduit pipe including earth continuity in surface/ recessed conduit wiring system. a) With 2 x 2.5 sq.mm .+ earth continuity with 1 x 1.5 s. cable in 20 mm.dia . Rigid Steel conduit.

b) With 2 x 4 sq.mm .+ earth continuity with 1 x 2.5 s. cable in 20 mm.dia . Rigid Steel conduit.

Wiring for drawing sub -main line with P.V.C. insulated single core unsheathed industrtial (Multistrand)cable FR conforming to IS- 694:1990 with flexiable bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/(RR cable or Euivalent Make as approved by the Deptt.) ISI marked steel conduit pipe including earth continuity in surface/ recessed conduit wiring system. a) With 3 x 2.5 sq.mm .+ earth continuity with 2 x 1.5 s. cable in 20 mm.dia . Rigid Steel conduit.

b) With 3 x 4 sq.mm .+ earth continuity with 2 x 2.5 s. cable in 20 mm.dia . Rigid Steel conduit.

Supply and fixing of 19 mm dia 1.50 mm to 2.00mm average wall thickness heavy rigid PVC IS:9537 Part- III conduit (Berlia /AKG/Precision/Presto plast/ Polycab/MW Or euivalent make as approved by the Deptt.) on surface system including paint etc as reuired:

Supply and fixing of 25 mm dia 1.50 mm to 2.00mm average wall thickness heavy rigid PVC IS:9537 Part- III conduit (Berlia /AKG/Precision/Presto plast/ Polycab/MW Or euivalent make as approved by the Deptt.) on surface system including paint etc as reuired:

Supply and fixing of 32 mm dia 2.00mm average wall thickness heavy rigid PVC IS:9537 Part- III conduit (Berlia /AKG/Precision/Presto plast/ Polycab/MW Or euivalent make as approved by the Deptt.) on surface system including paint etc as reuired:

Supplying and Fixing 19mm dia ISI marked steel conduit pipe (AKG or euivalent as approved by the Deptt.) on surface including painting etc. as reuired.

Supplying and Fixing 25mm dia ISI marked steel conduit pipe (AKG or euivalent as approved by the Deptt.) on surface including painting etc. as reuired.

Supplying and Fixing 32mm dia ISI marked steel conduit pipe (AKG or euivalent as approved by the Deptt.) on surface including painting etc. as reuired.

Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrtial (Multistrand)cable FR conforming to IS- 694:1990 with flexiable bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/(RR cable/Nicco/ Anchor or Euivalent Make as approved by the Deptt.) in existing surface conduit wiring system including connection as reuired. a) with 2 x 1.5 sq.mm. copper condutor cable.

b) with 3 x 1.5 sq.mm. copper condutor cable.

c) with 2 x 1.5 sq.mm. + earth continuity with 1 x 1.5 s. mm. copper condutor cable.

d) with 2 x 4 s. mm. + earth continuity with 1 x 2.5 s. mm. copper condutor cable.

Wiring for Co - axial / Jelly Flooded (Unarmoured) (FINOLEX /RR CABLE /NICCO / ANCHOR make ) cable in existing surface conduit wiring system including connection etc as reuired. a) Co - axial Jelly Flooded (Unarmoured) RG 11 (Copper)

Supplying and Fixing 18 S .W .G Sheet steel metal boxes of the following sizes in surfaces Wiring system with suitable size of 3 mm thickness phenolic laminated sheet cover on the front face of the boxes including painting etc. as reuired and specified by the department. a) 100 mm x 100 mm x 60 mm deep (Normal size)

b) 100 mm x 150 mm x 60 mm deep (Normal size)

c) 100 mm x 175 mm x 60 mm deep (Normal size)

d) 100 mm x 150 mm x 60 mm deep (Normal size)

e) 100 mm x 200 mm x 60 mm deep (Normal size)

f) 100 mm x 250 mm x 60 mm deep (Normal size)

g) 100 mm x 300 mm x 60 mm deep (Normal size)

h) 100 mm x 350 mm x 60 mm deep (Normal size)

i)100 mm x 350 mm x 60 mm deep (Normal size)

Supplying with fitting and fixing sheet steel , phosphatised,powder painted dust & vermin proof Double door (IP-43) surface mounting SPN MCB DB incorporated with bas - bar,Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as red. complete with making necessary connection as approved , specified and directed by the deptt. a) 6 way SPN double door

b) 8 way SPN double door

c) 12 way SPN double door

Supplying with fitting and fixing MCCB incomer and MCB Outgoiing sheet steel , phosphatised,powder painted Double door (IP-43) surface mounting vertical TPN MCB DB incorporated with bas - bar up to 250A ,Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as red. complete with making necessary connection as approved , specified and directed by the deptt. (ABB,Schneider MG legrand, Hager, Crabtree Xpro make) a) 4 way TPN ( 4 + 12 ) Double door

b) 8 way TPN ( 4 + 18 ) Double door

Supplying with fitting and fixing 7 segment sheet steel, phosphatised, powder painted surface mounting double door TPN DB (IP 43) incorporated with bas - bar up to 250A ,Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as red. with provision for FP MCB / RCCB / RCBO as sub incomer and SP MCB as out going complete with making necessary connection as approved, specified and directed by the deptt. a) 4 way TPN ( 8 + 12 +12 ) Double door

b) 6 way TPN ( 8 + 12 +18 ) Double door

c) 8 way TPN ( 8 + 12 +36 ) Double door

Supplying with fitting and fixing 7 segment sheet steel, phosphatised, powder painted surface mounting double door TPN DB (IP 42) incorporated with bas - bar up to 250A ,Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as red. common for MCB / Isolator etc. with phase segregation and separation between incoming and outgoing , making necessary connection as approved , specified and directed by the deptt. a) 4 way double door

b) 6 way double door

c) 8 way double door

Supplying with fitting and fixing SPN 10KA 240/ 415V 50Hz MCB of the following capacity complete with making necessary connection as approved ,specified and directed by the deptt. a). C Series (ABB ,Schneider MG , legrand , Hager , Crabtree Xpro make) 6 to 32A

b) . D Series (ABB ,Schneider MG , legrand , Hager , Crabtree Xpro make) 6 to 32A

Supplying with fitting and fixing DP 10 KA 240/ 415V 50Hz MCB of the following capacity complete with making necessary connection as approved ,specified and directed by the deptt. C Series (ABB ,Schneider MG , legrand , Hager , Crabtree Xpro make) a) .6 to 32A

D Series (ABB ,Schneider MG , legrand , Hager , Crabtree Xpro make) a) .6 to 32A

Supplying with fitting and fixing TP 10 KA 240/ 415V 50Hz MCB of the following capacity complete with making necessary connection as approved ,specified and directed by the deptt. C Series (ABB ,Schneider MG , legrand , Hager , Crabtree Xpro make) a) .6 to 32A

3.D Series (ABB ,Schneider MG , legrand , Hager , Crabtree Xpro make) a). 6 to 32A

Supplying with fitting and fixing TPN 10 KA 240/ 415V 50Hz MCB of the following capacity complete with making necessary connection as approved ,specified and directed by the deptt. C Series (ABB ,Schneider MG , legrand , Hager , Crabtree Xpro make) a) .6 to 32A

3.D Series (ABB ,Schneider MG , legrand , Hager , Crabtree Xpro make) a) .6 to 32A

Supplying with fitting and fixing 4P 10 KA 240/ 415V 50Hz MCB of the following capacity complete with making necessary connection as approved ,specified and directed by the deptt. C Series (ABB ,Schneider MG , legrand , Hager , Crabtree Xpro make) a) 6 to 32A

D Series (ABB ,Schneider MG , legrand , Hager , Crabtree Xpro make) a) 6 to 32A

Supplying with fitting and fixing 30/100 / 300 mA sensitivity 240/ 415V 50Hz DP RCBO of the following capacity complete with making necessary connection as approved ,specified and directed by the deptt. 30mA sensitivity DP RCBO (ABB ,Schneider MG , legrand , Hager , Crabtree Xpro make) a) .25A

30mA sensitivity 4P RCBO (ABB ,Schneider MG , legrand , Hager , Crabtree Xpro make) a) 25A

Supplying with fitting and fixing panel mounting open execution 25KA 415V 50Hz 4P MCCB (Ics = Icu ,adjustable lr setting 0.7) (without encloser)of the following capacity complete with making necessary connection as approved ,specified and directed by the deptt. a) 40A

Supplying with fitting and fixing panel mounting open execution 35 /36 KA 415V 50Hz 4P MCCB (Ics = Icu ,adjustable lr setting 0.7) (without encloser)of the following capacity complete with making necessary connection as approved ,specified and directed by the deptt. 35/36 KA 415V 50 Hz 4P MCCB (Schneider, legrand, Sismens, Hager make) a) 160A

Supply with installation & commissioning of ready made maintenance free CPRI approved chemical earthing system with 50mm dia .3.00 Metres length corrosion free Sinngle pipe tectnology .Copper CHEMRODE ELECTRODE complete with RESLOW Grounding Minerals 25K and Advance Earth Pit cover including excavation of earth pit and construction of brick earth chamber including plastering both inner & outer surface of brick wall as specified and directed by the deptt.

Supply, installation & commissioning of Advanced Lightning protection system by using High pulse Voltage ESE lightning condutor with Optimized Pulse Rod (ABB or euivalent make) as specified and directed by the deptt (as per NFC 17 -102 STANDARD & IEC Std 60 - 111989)

Supply installation & testing of copper plate earth station with 600mm x600 mm x 3 mm copper earth plate with necessary 40 mm dia . G.I. medium duty watering pipe with G.I. Fittings such as Socket, Tee, elbow ,nipple and 50 mm x 40 mm G. I. reducing socket for funnel including locking arrangement with 300mm x 300 mm x 6 mm C.I. hinged cover plate complete with digging of earth pit,construction of brick earth chamber including plastering both inner & outer surface of brick wall as specified and directed by the deptt.

Supplying & laying of 8 SWG Copper. Earth from earth Electrode ( below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved , specified and directed by the deptt.

Supplying & laying of 8 SWG G.I…Earth drawn through 15mm dia. Medium uality G.I. pipe from earth Electrode ( below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved , specified and directed by the deptt.

Supplying & laying of 25 x6 mm size G.I. strips drawn on surface from earth electrode to electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc including riveting ,soldering & making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 32 x 6 mm size G.I. strips drawn on surface from earth electrode to electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc including riveting ,soldering & making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 50 x 6 mm size G.I. strips drawn on surface from earth electrode to electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc including riveting ,soldering & making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 40 x 6 mm size Copper strips drawn on surface from earth electrode to electrical switch gears, machineries etc complete with supply of Brass nuts & bolts, screws etc including riveting ,soldering & making necessary connection as approved, specified and directed by the deptt.

3 & 1/2 Core A2XFY a) 35.00 Sq.mm. 3 & 1/2 Core armoured U.G. cable

b) 50.00 Sq.mm. 3 & 1/2 Core armoured U.G. cable

c) 70.00 Sq.mm. 3 & 1/2 Core armoured U.G. cable

d) 95.00 Sq.mm. 3 & 1/2 Core armoured U.G. cable

e) 120.00 Sq.mm. 3 & 1/2 Core armoured U.G. cable

f )150.00 Sq.mm. 3 & 1/2 Core armoured U.G. cable

g) 185.00 Sq.mm. 3 & 1/2 Core armoured U.G. cable

h) 240.00 Sq.mm. 3 & 1/2 Core armoured U.G. cable

i) 300.00 Sq.mm. 3 & 1/2 Core armoured U.G. cable

4 Core A2XWY A2XFY a) 4.00 Sq .mm .4 Core armoured U.G. Cable

b ) 6.00 Sq .mm .4 Core armoured U.G. Cable

c) 10.00 Sq .mm .4 Core armoured U.G. Cable

d) 16.00 Sq .mm .4 Core armoured U.G. Cable

e) 25.00 Sq .mm .4 Core armoured U.G. Cable

Supply and laying of following numbers and size of Stranded compact Circular Aluminium Conductor , condutor Screen with extruded semi conducting compound ,XLPE insulated ,insulation screening with extruded semi conduting compound in combination with Copper tape (0.3kA for 1se ,AL flat strip / round armoured and over all PVC Sheated cable confirming to IS 7098/ (PART -1 1985 with latest amendment , laid in ground/ partially in air (as reuried for termination over ground including excavation of cable trench up to depth of 120cm, refilling, protective brick covering ,Sand cushioning etc complete handling of surplus spoil ,debris et to proper place as specified and directed by the deptt. (Nicco / Havells / RPG/CCI/ Polycab/ Gloster/ Finolex make or euivalent). 11 KV (E) 3 X 240.00 Sq.mm 3 Core U.G. armoured cable

SUPPLYING FITTING AND TESTING OF (DOWELLS/COMET make) DOUBLE COMPRESSION BRASS GLANDSWITH NICKEL - PLATED WEATHERPROOF (CBW) Size: 8 - 10, 3/4 "

WEATHERPROOF (CBW) Size: 1Size: 2.5 - 16, 3/4 "

WEATHERPROOF (CBW) Size: 16.5 - 18, 3/4 "

WEATHERPROOF (CBW) Size: 16.5 - 18, 1 "

WEATHERPROOF (CBW) Size: 18.5 - 20, 1 "

WEATHERPROOF (CBW) Size: 20.5 - 23, 1 "

WEATHERPROOF (CBW) Size: 23.5 - 26, 1- 1/4 "

WEATHERPROOF (CBW) Size: 26.5 - 30, 1- 1/2 "

WEATHERPROOF (CBW) Size: 30.5 - 33, 1- 1/2 "

WEATHERPROOF (CBW) Size: 33.5 - 37, 1- 1/2 "

WEATHERPROOF (CBW) Size: 37.5 - 41, 2 "

WEATHERPROOF (CBW) Size: 41.5 - 46, 2 "

WEATHERPROOF (CBW) Size: 56.5 - 60, 2 -1/2 "

WEATHERPROOF (CBW) Size: 60.5 - 66, 3 "

SECTION – A: Ht Panels & Transformer Design, manufacture, testing at works, transportation to site, unloading, storing, erecting, testing & commissioning of 11KV, 630A, 26.2KA Single VCB PANEL (OUTDOOR TYPE Protection class - IP-66) of Floor mounting type, undrilled gland plates at bottom, complete with internal wiring, ferrules, name plates, painting etc., conforming to the technical specification for HT panels & comprising of the following. 1Set - 11kV, 630A, 26.2kA Draw out type TP VCB with Spring Charging Motor & Close/ Trip Coil Each set comprising of following CT's for metering - 120-60A/5A - 5A, Cl 0.5, 15VA CT's for protection - 120-60A/5A - 5A, Cl 5P15, 15VA 3phase 11kV/√3 / 110V/√3, Cl-0.5, 100VA Drawout type resin castin type.Breaker T/N/C switch Protection relay for 51,50, 51N, 50N, 95, 27,59, 86 (All relays shall be numerical type with all built in standard features for protection, recording, event logging, etc.) 12KV, 10KA surge arrester Metering with 1 RS-485 port & 1 ethernet modbusTCP interface / BACNET over IP with Digital type Ammeter ,Voltmeter & EM 6400 110V AC / 110VDC Power pack with continuous & stored energy R,Y,B,ON,OFF, Trip,CB spring charge, trip circuit Healthy indication Lamps (LED)- 110V AC Push button for trip circuit healthy, Emergency trip Space Heater with switch & thermostat, Power outlet with switch 20A Plug & Socket with control by 20A SPN MCB, lamp with door switch. Earth Leakege relay with CBCT Suitable window Annunciator with RS 485 port. Hooter .Yard work

Supply & erection of M.S. gate of size 3000mm wide & 2000mm height with all accessories,earthing of gates with braided copper including necessary civil works.Gate shall be painted with 2 coats of anticorrosive primer & 2 coats of Aluminiun enamel paint.

Supply & erection of M.S. gate of size 2000mm wide & 2000mm height with all accessories,earthing of gates with braided copper including necessary civil works.Gate shall be painted with 2 coats of anticorrosive primer & 2 coats of Aluminiun enamel paint.

Supply & spreading of 40mm blue metal filling upto 150mm depth over a river sand layer Rate shall include cleaning & levelling of the yard as required at site. (from existing ground level of 150mm height)

Supply & erection of 2.5mtr long (65X65X6mm ISA angle with aluminium paint) for fencing with necessary concreting & all accessories as required.

Supply & fixing of GI chain link fencing of height 2mtr. With necessary clamps,fasteners,binding wires,earthing of fencing at all sides with suitable GI wires including all accessories as required.

Charges towards digging, excavation of normal soil , cable trenches of required size for 800mm wide x 1200mm deep trench, providing sand bed, warning tap, RCC truff etc., Back filling the same for laying HT cables inside / outside building as per drawing.

Charges of manhole chamber sizes of 1200mm x 1200mm as above sl.no: 1.7 e & including necessary four side brick required.

Charges towards digging, excavation of normal soil , cable trenches of required size for 600mm wide x 1200mm deep trench, providing sand bed, bricks, warning tap, truff etc., Back filling the same for laying lT / LTcables inside / outside building as per drawing.

Charges of manhole chamber sizes of 1000mm x 1000mm as above sl.no: 1.7 f & including necessary four side brick required.

Supply, unloading, handling, safe keeping, Installation, testing and commissioning of 1000kVA, 11KV/433V, DYN11 Outdoor, ONAN type transformer with OLTC & RTCC panel. The tapping on HV for HV variation shall be of (+5)% to (-15)% in step of 1.25% by OLTC. Necssary phase and neutral CTs, control switches and transformer Protection relays should be provided such as Transformer Buchholz relay, OLTC surge relay, Oil temperature relay, winding temperature relay, magnetic oil level gauge and pressure relief valve with NO/NC, Auxiliary relays as per standards. The transformer should be complied Energy efficiency Level-3 as per IS-1180. The primary and secondary winding material shall be of copper. All hardware shall be hot dipped galvanised. The copper flexible strip shall be provided at every gasketted joint for earthing continuity purpose. The Transformer shall be provided with cable termination box on primary side to terminate 3C 240Sqmm XLPE Al. Ar. 11kV HT cable and on secondary side with 2500A Sandwich type aluminium busduct with all accessories as per the detailed specification and drawing enclosed.

SECTION – B: LT BUSDUCTS All installation works should be as complete and as directed by Employer / Empolyer's representative. The rate includes necessary connected minor civil works if required and necessary supports as required at site. No extra payment will be made for the same. LT BUSDUCTS Design, supply, erection, testing and commissioning of 1600 Amps 50kA indoor sandwich type aluminium 4Pole busduct and with suitable support from ceiling as per the detailed specification enclosed. The busduct shall have 2Rnus of external body earth conductor along full length of busduct. The busduct should be with straight run, 90 deg. horizontal and Vertical bends., busbar trunking fittings (elbow, tees, end End (Cable) feed Box, end covers, horizontal fixing devices,etc.) The horizontal runs of busbar trunking system shall be supported by hangers at every 2 metre. Vertical runs of busbar trunking system shall be supported by hangers not more than 4m apart. The busduct shall run from transfromer secondary to Main Power Control Center(MPCC). The bus duct shall be fabricated as per the detailed specification enclosed.

Design, supply, erection, testing and commissioning of 1600 Amps 50kA indoor sandwich type aluminium 4Pole busduct and with suitable support from ceiling as per the detailed specification enclosed. The busduct shall have 2Rnus of external body earth conductor along full length of busduct. The busduct should be with straight run, 90 deg. horizontal and Vertical bends., busbar trunking fittings (elbow, tees, end End (Cable) feed Box, end covers, horizontal fixing devices,etc.) The horizontal runs of busbar trunking system shall be supported by hangers at every 2 metre. Vertical runs of busbar trunking system shall be supported by hangers not more than 4m apart. The busduct shall run from transfromer secondary to Main Power Control Center(MPCC). The bus duct shall be fabricated as per the detailed specification enclosed.

Design, supply, erection, testing and commissioning of 1600 Amps flexible joints suitable for sandwich type TPN aluminium bus duct at end terminals including all accessories.(RYB+N=1 set)

Design, supply, erection, testing and commissioning of 1600 Amps Phase cross changeover box suitable for sandwich type TPN aluminium bus duct including all accessories. (it will operate in case of phase change over is required as per site condition) (RYB+N=1 set)

SECTION – C : LT PANEL BOARDS All installation works should be as complete and as directed by Employer / Employer's representative. As mentioned in SLD, MFM shall be provided in all panels incomer and MPCC panel's outgoings with necessary CTs, PTs, control switches and all other necessary accessories as per the specification and drawing. All the meters should have RS 485 modbus output for BMS integration and also All ACB & MCCB should have dedicated potential free contacts to monitor breaker's (ON/OFF) & TRIP status from BMS system. Each merter's RS 485 modbus output and above said potential free contactors shall be wired up to the terminal block which should be placed at marshalling feeder / common feeder of each panel section. Each terminal block should have 20 percent spare space. NOTE:- 1) All MCCB feeders shall be fixed type 2) All the breakers which is above 250A rated breaker should be provided with Microprocessor based release​​ and 250A & below the rated breaker should be provided with thermal magnetic release. 3) All starter feeders and fire fighting panel feeder should be provided with breaker which is suitable for motor application. 4) All breakers should have minimum kA rating as mentioned in BOQ. On non availability of specified breaker, immediate higher rating breaker must be provided. 5) All live parts should be shrouded by FRP transparent polycarbonate sheet of 2mm thick (Contd.)

Incomers 1set of 1600Amps 4Pole 50kA electrical draw out type Air circuit breaker with shunt release shutter assembly, door interlock and all other accessories. (Transformer) 2sets of 800Amps 4Pole 50kA electrical draw out type Air circuit breaker with shunt release shutter assembly, door interlock and all other accessories.(DG Set) 2sets of 250Amps 4Pole 50kA MCCB with shunt release shutter assembly, door interlock and all other accessories.(future solar ) Instruments Panel Providing TNC switch, emergency lockable push button, Maximum demand controller with RS485, Ammeter, Voltmeter, Instantaneous over current, earthfault relay (2 O/C+ 1 E/F), Restricted earth fault relay(64R) and necessary CTs, PTs, control MPCB/MCB/ ELCB/RCBOs, RYB Indication lamps and “ON/OFF/Trip/Reset" indicating lamp, voltage surge protection with emergency lockable push buttons. 2500A NCT shall be provided in the Transformers side of the neutral and also refer the specification and SLD. Bus coupler 1set of 1600Amps 4Pole 50kA electrical draw out type Air circuit breaker with shunt release shutter assembly, door interlock and all other accessories.(Contd.)

Outgoings 630A TPN MCCB, 50kA – 2Nos 250A TPN MCCB, 50kA – 9Nos 160A TPN MCCB, 50kA – 2Nos 100A TPN MCCB, 50kA – 1No Both incomers and buscoupler shall be interlocked with electrical and mechanical arrangements by hardware control wiring alongwith PLC (Programmable Logic Controls). Also providing protection relays and meters with necessary CT / PT, control MCB/ MPCB/ RCBO, hooter etc. and all as per the detailed specification and drawings enclosed. The PLC should have suitable communication port for BMS integration. The panel should have the provision to receive the pipe lines for proposed panel gas flooding system Both incoming and outgoing breakers should be provided with built-in microprocessor based release with overload,short circuit and earth fault releases and CBCT with earth leakage relay for monitoring, alarming (with help of hooter with flasher) and tripping function . Incoming metre for both incoming feeder shall be with demand controller, Harmonic THD and individual harmonic display+ Regular parameters like V, I, KVA, KVAR, KW, KWH, KVARh, PF, Freq, Max, AVG etc. All Outgoing Feeders in Main panel shall be with MFM monitoring V,I, KWH, KVARH, PF with RS 485 BMS integration. All the metres to be wired and terminated at common metre chamber / marshalling feeder of each panel section. 1600Amps 4P 50kA Aluminium busbars:- All the neutral busbars shall have the same capacity of phase busbars.

Design, Supply, testing and commissioning of cubicle type floor mounting switch board comprising of the following, the board shall be fabricated as per the detailed specification enclosed.GF PANEL Incoming 250A 4P MCCB 36kA with all connected accessories – 1 No incomer Outgoing 100A TPN MCCB 25kA - 3Nos. 63A TPN MCCB 25kA - 11Nos. 32A TPN MCCB 25kA - 4Nos. With necessary aluminium busbars, interconnections, providing Combined Digital type Mulitifunction Meter with RS485, RYB phase indication lamps, surge protection devices with necessary CTs, control MCB/MPCB/RCBOs etc. at incoming feeder. Also providing ON,OFF & TRIP indication lamps in all incoming & outgoing feeders with control MCBs / MPCB etc. All MCCBs should have two (spare) potential free contactor for monitoring breaker ON, OFF & TRIP status through BMS and all as per the specification and drawings. 250 Amps 4P 36kA aluminium busbars:- All the neutral busbars shall have same the capacity of phase busbars.

Design, Supply, testing and commissioning of cubicle type floor mounting switch board comprising of the following, the board shall be fabricated as per the detailed specification enclosed. 1st & 2nd floor panel & RECP panel Incoming 250A 4P MCCB 36kA with all connected accessories – 1 No incomer Outgoing 100A TPN MCCB 25kA - 3Nos. 63A TPN MCCB 25kA - 6Nos. 32A TPN MCCB 25kA - 4Nos. With necessary aluminium busbars, interconnections, providing Combined Digital type Mulitifunction Meter with RS485, RYB phase indication lamps, surge protection devices with necessary CTs, control MCB/MPCB/RCBOs etc. at incoming feeder. Also providing ON,OFF & TRIP indication lamps in all incoming & outgoing feeders with control MCBs / MPCB etc. All MCCBs should have two (spare) potential free contactor for monitoring breaker ON, OFF & TRIP status through BMS and all as per the specification and drawings. 250 Amps 4P 36kA aluminium busbars:- All the neutral busbars shall have same the capacity of phase busbars.

Design, Supply, testing and commissioning of cubicle type floor mounting switch board comprising of the following, the board shall be fabricated as per the detailed specification enclosed. Utility panel Incoming 160A 4P MCCB 36kA with all connected accessories – 1 No incomer Outgoing 100A TPN MCCB 16kA - 3Nos. 63A TPN MCCB 16kA - 5Nos. 32A TPN MCCB 16kA - 4Nos. With necessary aluminium busbars, interconnections, providing Combined Digital type Mulitifunction Meter with RS485, RYB phase indication lamps, surge protection devices with necessary CTs, control MCB/MPCB/RCBOs etc. at incoming feeder. Also providing ON,OFF & TRIP indication lamps in all incoming & outgoing feeders with control MCBs / MPCB etc. All MCCBs should have two (spare) potential free contactor for monitoring breaker ON, OFF & TRIP status through BMS and all as per the specification and drawings. 160 Amps 4P 36kA aluminium busbars:- All the neutral busbars shall have same the capacity of phase busbars.

Design, Supply, testing and commissioning of cubicle type floor mounting switch board comprising of the following, the board shall be fabricated as per the detailed specification enclosed. Pump panel Incoming 250A 4P ATS With 250A 4P MCCB 36kA with all connected accessories – 1 No incomer Outgoing 63A TPN MCCB 16kA with Star / Delta starter - 8Nos. 32A TPN MCCB 16kA with Star / Delta starter - 4Nos. With necessary aluminium busbars, interconnections, providing Combined Digital type Mulitifunction Meter with RS485, RYB phase indication lamps, surge protection devices with necessary CTs, control MCB/MPCB/RCBOs etc. at incoming feeder. Also providing ON,OFF & TRIP indication lamps in all incoming & outgoing feeders with control MCBs / MPCB etc. All MCCBs should have two (spare) potential free contactor for monitoring breaker ON, OFF & TRIP status through BMS and all as per the specification and drawings. 250 Amps 4P 36kA aluminium busbars:- All the neutral busbars shall have same the capacity of phase busbars.

SECTION-E :UPS AND BATTERIES Supply, Installation, Testing and commissioning of 15KVA UPS system 3 phase input and three phase output and as per the detailed specification enclosed. Supply, Installation, Testing and Commissioning of 2V, VRLA (SMF) Sealed Maintenance Free Batteries to support 15KVA for 15 minutes complete with intercell connectors & copper cables, battery stand made out of Powder Coated MS Angles with adequate supports to carry the load of the batteries. The vendor shall submit dimensional GA drawing of complete UPS system, battery rack with batteries,Service bypass Panel and Battery bank calculations along with offer.

Supply, Installation, Testing and commissioning of 40KVA UPS system 3 phase input and three phase output and as per the detailed specification enclosed. Supply, Installation, Testing and Commissioning of 2V, VRLA (SMF) Sealed Maintenance Free Batteries to support 40KVA for 15 minutes complete with intercell connectors & copper cables, battery stand made out of Powder Coated MS Angles with adequate supports to carry the load of the batteries. The vendor shall submit dimensional GA drawing of complete UPS system, battery rack with batteries,Service bypass Panel and Battery bank calculations along with offer.

SECTION-E : SWITCH AND SOCKETS: 1No 20A 240V 3 pin industrial type polycarbonate plug & socket with 20A SP MCB (C-Curve) in a suitable size enclosure fixed in open / recessed system.(MULTIPURPOSE)

1No 20A 240V 3 pin industrial type polycarbonate plug & socket with 20A DP MCB (C-Curve) in a suitable size enclosure fixed in open / recessed system.( CANTEEN / CAFETERIA)

1No 20A 240V 3 pin industrial type polycarbonate plug & socket with interlocking arrangement and controlled by 20A DP MCB (D-curve) in a suitable size enclosure fixed in open / recessed system.(SERVER RACK )

Design, supply,fixing, testing and commissioning of 32A 5pin industrial type socket controlled by 32A 4P RCBO 30mA in a suitable size enclosure fixed in open system.(CAR CHARGING)

Supply, fixing, testing and commissioning of 2 nos. 6/10/13A Universal Socket controlled by 1 No. of 10A switch and space provision for2Nos of RJ45 & 1No. of RJ11 socket in suitable size POP UP Box (8M) on floor /table with suitable Flush-mounting boxes for installation in concrete floors / table top, Colour shall be Brushed stainless steel finish and suitable metal back box, necessary earthing terminals provided at the back box for safety.

a) Supply and fixing of 1/2module modular box

SECTION – F: SAFETY & MISCELANIOUS ITEM All installation works should be as complete and as directed by Employer / Employer's representative. The rate includes necessary connected minor civil works if required and necessary supports as required at site. No extra payment will be made for the same. Supply and laying of 2.0mm thick 1000mmx2000mm wide chequered rubber mat with ISI mark suitable for 440V installation .(IS 15625)

Supply and fixing of LT cable route indicator made out of MS flat and angle iron. The cable route marker shall be fixed at both the ends of cable at joints and 15mtrs spacing for straight runs.

Supply and fixing of HT cable route indicator made out of MS flat and angle iron. The cable route marker shall be fixed at both the ends of cable at joints and 15mtrs spacing for straight runs.

Supply and providing shock treatment chart in English and Hindi duly framed with 2mm thick glass in front & 6mm thick ply on back as required

Supply and fixing of GI fire buckets with round bottom, each set comprising 4Nos.fire buckets of 9Kg capacity including supply of M.S pedestal stand with hooks suitable for holding of 4Nos of fire buckets, painted with Post Office Red oil paint and letter FIRE on each bucket and filling with sand complete as required.

Supply and providing St. John make first aid box 18SWG MS sheet duly painted as approved by Indian red cross soceity complete with all first aid medicines.

Supply & Fixing HT danger notice plate 250mm x 200mm made of MS steel 2mm thick & Vitreous enameled white on both sides and with inscriptions in signal Red on front side as required by the electrical authorities.

Supply & Fixing LT danger notice plate 200mm x 150mm made of MS steel 2mm thick & Vitreous enameled white on both sides and with inscriptions in signal Red on front side as required

Supply and erection of fire extinguisher Co2 4.5 Kg. confirm to IS norms.

Supply & Fixing of MS sheet board of size 500mm x 300mm of 16 SWG with Entry Restricted To Authorised Persons Only near the Main entrance of the Substation. The lettering shall be Black painted on Yellow Back ground.

Supply and Erection of Fire resistant Mortar with fire resistance class S90 according to testing standard DIN 4102 Part 9 DIBT approval Z- 19.15 – 2046 suitable to seal the openings with all kinds of cables, pipes and cable support system in steel and , aluminium and plastic profiles ( Except hollow core conductors). The residual openings shall be closed with filler. (Equivalent to Pyromix of OBO Bettermann - Model: MSX - S1)

Supply and Erection of Fire Protection foam from with fire resistance class to EI120 according to testing standard EN 1366 PART 9 approval ETA -11/0527, VKF 22552,22553,22554,22555 suitable to seal the openings with a combination insulation cables, pipes and the cable trays. (Equivalent to Pyrosit NG fire protection foam of OBO Bettermann) -350ml tube

Supply and fixing of 50mm dia PVC HMS conduit with all necessary accessories like junction boxes, bends, couplers, fixing material like clamps, screw etc.

Supply and fixing of 75mm dia PVC HMS conduit with all necessary accessories like junction boxes, bends, couplers, fixing material like clamps, screw etc.

Supply and fixing of 60mm dia SWR (steel wire reinforced) PVC flexible conduit with all necessary fixing accessories and suitable glands.

Supply and fixing of 110mm dia SWR (steel wire reinforced) PVC flexible conduit with all necessary fixing accessories and suitable glands.

Towards professional charges for filing application, follow up with State Electricity board department, getting the load sanction of power, load release letter and certificate for installations loads. The rate shall including arragning inspection to the respective department at site.

Towards professional charges for preparation of drawings in necessary formats for approval, follow up and arranging approval of drawings, scheme by Local electricity authority / Electrical Inspectorate (CEIG), arranging inspection, obtaining safety certificate clearance from electrical Inspectorate for the installation and arranging power connection. The Rate shall be including preparation and submission of as built drawings of entire installation of the works executed need to be submitted in the blue print of A1 size as required in 6Sets of hard copy and two set sets of soft copy in CD. The rate shall inclusive of all Machinaries and Equipments supplied and installed by Other agency also.

Cable Trays & MS Supports Supply & installation of Hot -dip galvanized cable rack system made of 2mm thick sheet steel folded with two longitudinal side rails connected by rungs at regular intervals of following sizes with necessary Tee's, Vertical/ Horizontal Bends, expansion anchor fasteners, coupler plates, coupling fasteners, including supply & grouting of supports as required at site. The supports should be painted with black enamel paint over a coat of anti corrosive primer. (Tray shall be measured along the central axis of the cable tray, 1000mm above sizes are fabricated by MS items). Note: Cable try shall be required two colours as per site condition. a) 750mm width Ladder Tray 100mm Height

b) 600mm width Ladder Tray 100mm Height

c) 450mm width Ladder Tray 50mm Height

d) 300mm width Ladder Tray 50mm Height

SECTION – J: LIGHTING LUMINAIRES & FANS All installation works should be as complete and as directed by Employer / Employer's representative. Samples to be submitted and get approval fom Architect / Consultant before procurement For LED light fittings, the complete luminaire should have a warranty for 5 years which includes the housing + LED + Driver Supply, Fixing, testing and commissioning of the following light fittings with all other necessary accessories. The rate shall be inclusive of suitable MS supports,GI Clamps and gripple make cable with crimp arrangement ,and chain suspenders .The height of the hanging arrangement shall be as per drawing and with all accesories to fix the hangers at purlin, rafter beam ,MS supports and walls with required clamps nuts & bolts to be considered. Also the rate includes necessary connected minor civil works if required and necessary supports as required at site. No extra payment will be made for the same. Supply, fixing, testing and commissioning of LED Cove light.Similar to Philips - Smart LED Flexible Cove (For Board Room, Huddle space etc,) Basic Rate - Rs. 235/-

Supply, fixing, testing and commissioning of LED 15W Suface mounted Tubler type Down light LED Light fitting

Supply, fixing, testing and commissioning of LED 15W Recess mounted type Down light LED Light fitting Philips Make DN296B LED15S-6500 PSU WH

Supply, fixing, testing and commissioning of LED 20W Surface mounted Batten type LED Light fitting Philips Make BN021C LED20S PSU CW GR S2

Supply, fixing, testing and commissioning of LED 10W Suface mounted Tubler Down light type LED Light fitting Philips Make DN295B LED10S-6500 PSU WH

Supply, fixing, testing and commisioning of Decorative lighting Special Light fitting (shapes as per Architectural Design Basic Rate 75000

Supply, fixing, testing and commisioning of Decorative lighting Special Light fitting (shapes as per Architectural Design ) Basic Rate 15000

Supply, fixing, testing and commisioning of Decorative lighting Special Light fitting (shapes as per Architectural Design Basic Rate 25000

FIRE ALARM SYSTEM

Supply, Installation , Testing and Commissioning of Addressable Input / Output Module Brand : ( Morley / Firelight / Appollo or Equvilanet as approved by the Dept.)

Supply, Installation , Testing and Commissioning of Addressable Loop Isolator Brand : ( Morley / Firelight / Appollo or Equvilanet as approved by the Dept.)

Supply, Installation, Testing & Commissioning of intelligent,plug in photo electric smoke detectors having features like integeral communication, dual LED for 360 Degree viewing angle, walk test with address display etc. UL/LPCB Approved, Make: Honeywell / Morely IAS .Model :MI-PSE or Equivalent as approved by the Dept

Supply, Installation, Testing & Commissioning of intelligent plug in Thermal Detectors having features like integral communication, dual LED for 360* viewing angle, walk test with address display etc. UL/ LPCB approved, :HONEYWELL or equivalent as approved by the Deptt.)

Supply, Installation, Testing & Commissioning of response indicator to give visual indiction of detection of smoke - RED colour LED for indication. Make - (Agni Suraksha, or equivalent as approved by the Deptt. ) System Sensor.

Supply, Installation, Testing, commissioning of Panel, Maximum 10 Loops Dual Processor, 8 loops with Nerworkable, No Loops Fitted, Requires loop card and network card additionally for networking, Zone Indication, Colour graphical LCD display, Integrated PSU with Battery Charger Brand: (MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)

Supply, Installation, Testing, commissioning of Loop card for Addressable Panels make-(MORLEY/FIRELINE/Apollo or equivalent as approved by the Deptt.)

Supply & Fixing of 2 X1.5 Sq. mm PVC Insulated Copper Armoured Cable on surface / recess/ above false Ceiling etc. As required (ISI Marked)

BELL RELAY MODULE: Supply, Installation, Testing, and Commissioning of "Addressable Bell Relay Modules”, UL Listed. Bell relay module shall be used for activating Notification devices. The module should be supported independently of their attachment to wirings using necessary mounting GI 4 X 4 Junction Box with cable gland, clamps/brass screws etc.

Supply, Installation, Testing & Commissioning of Monitor Module. UL / LPCB approved, make - Honeywell, MORLEY IAS or equivalent as approved by the Deptt. With housing box

Supply, Installation, Testing & Commissioning of Manual pull station with addressable interface, built in LED with key reset facility. UL/LPCB listed. Make: (HONEYWELL, MORLEY IAS or equivalent as approved by the deptt.)

Supply, Installation, Testing, and Commissioning of “24V / 5A Power supply unit”, for power the hooter cum strobe modules. The vendor shall specify the capacity and quantity as required based on their respective technical requirements. The Power supply unit should be supported independently of their attachment to wirings using necessary wall & column mounting support, clamps/brass screws, etc.

Supply & Fixing of 2 X1.5 Sq. mm PVC Insulated Copper flexible Cable with PVC conduit necessary pipe fittings. Cable joints on surface / recess/ above false Ceiling etc. As required (ISI Marked)

PUBLIC ADDRESS SYSTEM

Supply and fixing of 25 mm dia 1.50 mm to 2.00mm average wall thickness heavy rigid PVC IS9537 Part -III Consduit (Berlia / AKG/Precision /Presto Plast /MW or equivalent Make as approved by the Dept.) on surface system including paint etc as required

Crown (Or Equivalent as approved by the Deptt). Supplying , Installation,Testing, Programming and commissioning of audio equipment, Duel channle power amplifier, 550 W @ 2Ohm,350W @ 4ohm,215 W@ 8ohm per channel

JBL (Or Equivalent as approved by the Deptt.) Supply, Installation , Testing ,programming and commissioning of Audio equipment, 4" Open ? Back ceiling speakers . 70V,/ 100V taps at 6W , 3W,1.5W (Plus 0.75W at 70V), high 93 dB sense, 60 Hz to 18 kHz, for non-plenum applications, 1.2kg.

Supply & Fixing of 2 X1.5 Sq. mm PVC Insulated Copper Armoured Cable on surface / recess/ above false Ceiling etc. As required (ISI Marked)

FIRE PROTECTION SYSTEM

5 HP Three phase vertical multistage high pressure centrifugal pump set 12 stage (Crompton Greaves / Aquatic /CRI/ V - Guard / Cal,a make)with starter delta Starter(Crompton Greaves)

10 HP Three phase Centrifugal monoblock pump set (Crompton Greaves / A/ Aquatic /CRI/ V - Guard / Cal,a make) 2900 rpm A class insulation with Star Delta Starter (Crompton Greaves/ Control & Switch Gear /BCH /L&T /Siemens make ) Fully Automatic citation.

Providing,Fixing,Testing & Commissioning of Mild Steel Black Pipe(IS:1239part-I) Heavy class including cutting, screwing, welding etc. and providing all fittings viz forged steel screwed fitting upto 50mm dia and bolt welded above 50mm dia flanges, bends, tees, reducers, elbow, clamps, hangers etc including cutting holes and chases in brick or RCC walls/ slabs and making good the same to the approval of Engineer-in-charge/ consultant complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade including steel work complete as required. (Make:TATA/JINDAL/NEZONE) a) 200 mm dia

b) 150 mm dia

c) 100 mm dia

d) 80 mm dia

f) 50 mm dia

i) 25 mm dia

Supplying & Fixing Cast iron body Non Return valves complete with matching flanges, rubber insertion, nuts, bolts and washer etc. (IS:5312) of following sizes complete as reqd. (Make:Koley/Kalpana/Audco) (b) 100 mm dia

(c) 80 mm dia

Supplying & Fixing,cast iron body Butterfly Valves with matching flanges, rubber insertion, nuts, bolts and washer etc (IS:13095) of following size complete as reqd. (MAKE:KOLEY/KALPANA/AUDCO) (c) 100 mm dia

(d) 80 mm dia

Providing ,Fixing,Testing & Commissioning of G.M. Stop Valve ISI Marked screwed type tested to 30Kg/cm2 pressure as per IS:778-1984 of following sizes complete as reqd. (a) 50 mm dia

(b) 25 mm dia

Providing ,erection,Testing & Commissioning of Pressure Switch (MAKE:INDFOSS)

Providing,erection testing & commissioning of pressure gauge 100 mm dia (0-10Kg/cm2)

Supplying fitting and fixing M.S.angles, M.S. flat, M.S. bolts and nuts including painting with red lead paint one coat complete as directed.

Supplying and placing ferrocement water tanks of circular/rectengular shape over stagging with manhole cover with locking and clearing arrangement including providing pads of size as required for inlet and outlet pipes complete as directed.(Stagging should be measured and paid separately). 1000 Lt capacity water tank

INTERNAL HYDRANT SYSTEM

Providing,Fixing,Testing & Commissioning of Mild Steel Black Pipe(IS:1239part-I) Heavy class including cutting, screwing, welding etc. and providing all fittings viz forged steel screwed fitting upto 50mm dia and bolt welded above 50mm dia flanges, bends, tees, reducers, elbow, clamps, hangers etc including cutting holes and chases in brick or RCC walls/ slabs and making good the same to the approval of Engineer-in-charge/ consultant complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade including steel work complete as required. (Make:TATA/JINDAL/NEZONE) a) 100 mm dia

b) 80 mm dia

c) 50 mm dia

d) 25 mm dia

Supplying & Fixing,cast iron body Butterfly Valves with matching flanges, rubber insertion, nuts, bolts and washer etc (IS:13095) of following size complete as reqd. (MAKE:KOLEY/KALPANA/AUDCO) (c) 100 mm dia

(d) 80 mm dia

Supplying, Installation, Testing & Commissioning of First Aid Hose reel drawn with 30 Mtrs. Long rubber hose and G.M shut off nozzle, 25mm dia Gate valve, Union pipe complete set confirming to IS: 884.

Providing ,Fixing ,Testing & Commissioning of air Release Valve a) 25 mm dia

EXTERNAL HYDRANT WORKS

Providing & Fixing of Gun Metal fire Brigade Connection (inlet collection head) consisting of 63mm instantaneous type male coupling with built in check valves and 150 mm dia flanged outlet complete with bolts, nuts and rubber insertions as per IS:904-1983 complete as reqd. MAKE: ESSEL/WINCO/NEWAGE a) 04 way

Providing,Fixing,Testing & Commissioning of Mild Steel Black Pipe(IS:1239part-I) Heavy class including cutting, screwing, welding etc.complete with all fittings (butt welded) viz flanges, bends, tees, elbows, reducers etc including excavation (upto 1.5 m Deep), back filling and removal of surplus soil & providing anti corrosive treatment(coating and wrapping) as per IS:10221 with 4 mm thick tape complete as reqd. (MAKE:TATA/JINDAL/NEZONE) a) 100 mm dia

Supplying and laying of following size NP2 class RCC Hume pipe i/c collars jointed with stiff mixture of cement morter 1:2 ( 1 cement:2 fine sand) across the road including cutting the road ( if reqd) digging the trench, refilling the same after laying pipe, ramming the soil etc as reqd. (a) 300 mm dia

Supplying fitting and fixing M.S.angles, M.S. flat, M.S. bolts and nuts including painting with red lead paint one coat complete as directed. a) M. S. Angles…….

Supply, installation, testing & commissioning of Diesel Engine driven common stand by pump, horizontal centrifugal end suction back pull type with gland packing and capable to deliver 1620LPM at 70MWC to ensure a minimum pressure of 3.5 Kg/Sqcm at the farthest or topmost hydrant / sprinkler. Fire pump shall have C.I. casing, CS diffusers, bronze impeller (hard finished and dynamically balanced) and S.S. (304) Shaft with mechanical seal. The installation shall be complete with necessary pressure gauge with gun metal shut off cock on delivery side. The pump shall coupled to suitable HP of Diesel engine radiator water cooled type with speed of 1800 RPM approx. and complete set shall be mounted on common base frame. Batteries & battery leads with stand, Fuel tank ( for 6 Hrs. operation ) and other standard accessories, (as recommended by manufacturer) and foundation bolts, etc. complete

CONTROL PANEL FOR FIRE PUMPS

Supply, Installation, testing & Commissioning of Booster pump with necessary control system complete all.

1100 V GRADE POWER / CONTROL CABLES Supplying, installing, testing and commissioning of FRLS, PVC outer sheathed, steel armored, aluminium conductor, 1100 v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The rate shall excludes tray & Hume pipes. The minimum size of the cables shall as mentioned below. a) 3.5 C x70 /90 sq. mm Aluminium cable for main pumps

b) 4 C x 16 sq. mm. Aluminium cable for Jockey pumps

c) 12 C x 2.5 sq. mm. Aluminum cable Diesel engines

d) 2 C x 2.5 sq. mm Copper armored for Instrumentation

e) 3 C x 2.5 sq. mm Copper armoured cables For start / stop push buttons

CABLE TRAY Supplying and installing of perforated G.I. sheet cable tray with necessary angle iron suspension supports, anchor fasteners etc. complete. Maximum height of suspension shall Not exceed 500 mm. Size of the tray shall be suitable for laying the above mentioned cables. a) 40 x 200 x 40 mm

Supplying, installing, testing and commissioning of G.I. Earthing strips of 50 mm x 6 mm thick, strip shall be run on floor / ceiling / walls, from the equipment to the nearest Earth pit with necessary accessories as required. (Earth pit shall be executed by other agencies). a) 50 mm x 6 mm thick - GI strip

Supplying, installing, testing and commissioning of Cast Iron (CI) foot valve as per IS:5312 (PN 16) with required flanges, nuts, bolts and gaskets etc. complete. a) 100 mm Nominal dia

b) 80 mm Nominal dia

Supplying, installing and commissioning Cast Iron flanged "Y" type Strainer with SS mesh, suitable flanges, nuts, bolts, gaskets etc. complete. a) 100 mm dia.

Supplying, installing, testing and commissioning of additional length of exhaust pipes M.S. Medium grade Class B with mineral wool insulation with aluminium sheet with long radius bend from residential silencer with necessary clamps, fixtures, civil works and 2 coat painted with heat resistant, rust proof, bituminous paint of approved colors to full height, in stages of following sizes including suitable rain guard for top. Fixing shall be done with proper GI clamps, expansion bolts, support angle of size 40X25X3mm , also painted, fixed on the wall / inside the duct etc. .... complete, as instructed by the Engineer. 150 mm dia M.S. Medium grade with mineral wool insulation with aluminium sheeting.

Supplying, installing, testing and commissioning of precharged air vessel (size 450 mm dia & 2000 mm height) for pressurization of hydrant / sprinkler system complete with adequate pressure switches (as per design / requirement) with valves to operate as per operating sequences including 25 mm dia drain valve, air release valve with stop cock on the top, 25 mm dia inlet with isolating valve duly painted from inside and outside complete as required. Shall be installed at the Plant room

Diesel tank 200 Litres with Stand and level identification tubes

Battery set with stand

FIRE EXTINGUISHERS

Supply, Installation, Fixing of DRY CHEMICAL POWDER Fire Extinguisher confirming to IS: 2171 with ISI mark and CO2 cartridge will be confirming to IS: 4947 with ISI mark, Powder will be confirming to IS: 4308 with ISI Mark (5 KG) BRAND : FIRESTOP / FIREND / FIRE SHIELD

Supply, Installation, Fixing of CARBON DIOXIDE Fire Extinguisher confirming to IS: 2878 with ISI Mark.(4.5 LITERS) BRAND: FIRESTOP / FIREND / FIRESHIELD

Supply, Installation, Fixing of MECHANICAL FOAM (AFFF) Fire Extinguisher confirming to IS: 10204 with ISI Mark and CO2 Cartridge will be confirming to IS: 4947 with ISI mark, (AFFF) will be confirming to IS: 4989 with ISI Mark.(50 LITERS) BRAND : FIRESTOP / FIREND / FIRE SHIELD

5KG MODULAR TYPE CLEAN AGENT FIRE EXTINGUISHER: Supply, Installation of 5 kg modular type ceiling mounted clean agent gas extinguisher, with MIG welded M.S body type 2mm thick with adapter / flange for fixing in ceiling and below part of automatic sprinkler releasing nozzle(brass) and pressure indicator with all mounting accessories. (The vertical hanging support height for the cylinder to be as per site condition)

VIDEO SERVILANCE SYSTEM

Supplying Installation testing and Commissioning of - 1/3" Super HAD CCD II, 600 TVL Dome Camara, Min illumination : 0.15 Lux @ F1.2, Built in fixed lens: 8 mm, Compact Dome Camara (8mm) , 600TV lines resolution (SAMSUNG or equivalent PELCO/ HONEYWELL / PANASONIC make)

Supplying installation testing and commissioning of -16 Chanel CIF Real Time DVR, upto 400 (PAL) fps recording rate, Max 4 internal HDD (HDDx4) , 4 Audio Inputs, 1 Channel Audio Output, DVR-RW (SUMSUNG or equivalent PELCO/ HONEYWELL/ PANASONIC make )

Supplying installation testing and commissioning of Hard Disk For DVR 2 TB (SEAGATE / WD make)

Supplying installation testing and commissioning of Power Suppy SMPS Based 12V For 16 Camera (PROTEK make)

Supplying installation testing of UTP CAT 6 without PVC conduit

Supply and fixing of 25 mm dia 1.50 mm to 2.00mm average wall thickness heavy rigid PVC IS9537 Part -III Consduit (Berlia / AKG/Precision /Presto Plast /MW or equivalent Make as approved by the Dept.) on surface system including paint etc as required

Supplying installation testing and commissioning of 24 port L2 PoE Switch

CIF(352x288): PAL. c.6-step quality level adjustable Capabillity of streaming: a.Each channel supports dual streams; each stream's parameter can be set individually. b. Each channel supports multi cast capability. c. Bit rate of each stream can be set to be variable or constant. Multiple simultaneous functions: a. Live viewing b. Recording c. Local Playback d. Network transmission e. Back-up Multiple control options: a. Standard PC mouse. b. Front panel control buttons. c.Control Centre software. Search functions: a. Date/time search b. Event search c. Channel search PTZ control: a.RS485 Interface b. Support Pelco P/D protocol, Scan dome protocol, Diamond protocol, Manual Export and back up of video via USB device or network. Easy to use features. a. Digital 200m or live and playback images. b. Support 4 clannels simultaneous payback locally. c. Exported video for legal disputes without the need for additional software. Multi-level of user IDS for security : Administrator and multi-level management.

VENTILATION SYSTEM

Supply, Installation, Testing and Commissioning of cabinet type single skin fan section, Drive Package, plenum chamber for suction ducts connections, bird screen, etc.Cost shall be necessary starter panel, control and power cabling of 100 meters complete all. a) 3000 CFM @ 40 mm SP - Toilet Exhaust

Supply, installation, testing and commissioning of round duct in line fans - 300 mm dia of 150 cfm complete all.

Supply, Installation, Testing and Commissioning of factory fabricated GSS Ducting with supports, flanges (TDS) as specified of the following sizes. Duct fabrication shall be SMACNA a) 24 G

Supply, Installation, Testing and Commissioning of Insulated / Uninsulated flexible duct with necessary supporting threaded rods, anchor fasteners , clamps & tapes a) 100 mm dia

Supply, installation, testing and commissioning of 150 mm dia. Aluminium powder coated toilet exhaust valves

Supply, Installation, Testing and Commissioning of spigot & Butterfly Dampers of sizes a) 100 mm dia

Supply, Installation, Testing and Commissioning of Aluminium powder coated Fresh air louvers non vision type with nylon mosquito net, pre filter, etc as per the specifications.

ELEVATORS

SITC of Passenger Elevator of Reputed and Approved Make of 8-passenger capacity and of Gearless - Machine Roomless Type. Supplying installation , testing and commissioning of 8 passenger (544 kg.)/ lifts having contract speed of 1 MPS serving different floors in the lift shaft as per detailed specification enclosed and as under : 1. No . Of Elevators - 1 NO. 2.Type - Passenger Elevator 3.Capacity Passenger - 8 Persons -544kg 4.Speed -1.0 Metre / sec (approx.) 5. Type of Drive - Variable Voltage variable Frequency Drive with Microprocessor based Simplex Full Collective Control. 6. Location of Machine room - N.A 7.Available Travel - 12.9 Metres. (Maximum) 8. Serving - Ground floor to 2nd floor 3 Stops 3 Levels 3 Openings 9. Well Size (Required) : as per Drawing 1800mm WIde x 1600 Deep (over plaster) approx. 10. Power supply 415 V three - phase 50 cycles AC 11. Auxiliary Required Single - phase 220 V 50 Cycles AC 12. Car size (Clear inside) : as per app. model 1300mm Wide x 1100mm Deep x 2300mm Height (Contd.)

13.Required Pit Depth -1400 mm approx. (Mandatory) 14.Required Head Room - 4000mm min. 15. Car Enlcosure - Stainless Steel Hairline Finish 16. Flooring - 20mm recessed Granite of app. shade 17.Electric Light - RL20F 18. Fan - Axial flow-1000 cu.M/hour 19.No. of Entrances - one location - Front . 20. Car Entrance Automatic power operated Centre Opening Stainless Steel Door 21.Landing Entrance Automatic power operated Centre Opening Stainless Steel Door : S.S Hairline Finish : 2-hr FIre rated 22.Clear opening 800mm Wide x 2100mm High 23. Indicators : Car & Landings : S.S Hairline Finish Direction & Position indicator 24. Car Operating Panel : Full height S.S Hairline Finish 25. Other Features Battery Operated Emergengy Alarm and Light . OSG Electronic Switch .Call Registration LEDs, 2 Station Intercom system, Full-height Infra -red Light curtain Door Safety. Automatic Rescue Device . Lift Annoucement System, Pit Ladder, Door Frames on all Landings, 2 hours Fire-rated Landing doors, S.S Round tubular Handrail (rear side), 4mm Mirror.

SITC of Goods / Freight Elevator of Reputed and Approved Make of 2000kgs capacity and of Gearless - Machine Roomless Type. Supplying installation , testing and commissioning of 8 passenger (544 kg.)/ lifts having contract speed of 1 MPS serving different floors in the lift shaft as per detailed specification enclosed and as under : 1. No . Of Elevators - 1 NO. 2.Type - Service / Goods / Freight Elevator 3.Capacity Passenger - 8 Persons -544kg 4.Speed -0.5 Metre / sec (approx.) 5. Type of Drive - Variable Voltage variable Frequency Drive with Microprocessor based Simplex Full Collective Control. 6. Location of Machine room - N.A 7.Available Travel - 12.9 Metres. (Maximum) 8. Serving - Ground floor to 2nd floor 3 Stops 3 Levels 3 Openings 9. Well Size (Required) : as per Drawing 2600mm Wide x 3000 Deep (over plaster) approx. 10. Power supply 415 V three - phase 50 cycles AC 11. Auxiliary Required Single - phase 220 V 50 Cycles AC 12. Car size (Clear inside) : as per app. model 1500mm Wide x 2500mm Deep x 2600mm Height

13.Required Pit Depth - 2000 mm approx. (Mandatory) 14.Required Head Room - 4200mm min. 15. Car Enlcosure - M.S Painted Finish 16. Flooring - Steel Chequered Plate 17.Electric Light - Square LED Spot Light (L54) 18. Fan - Cross flow-270 cu.M/hour 19.No. of Entrances - one location - Front . 20. Car Entrance Automatic power operated Centre Opening (4 Panel) 21.Landing Entrance Automatic power operated Centre Opening Door : M.S Painted : 2-hr FIre rated 22.Clear opening 1400mm Wide x 2400mm High 23. Indicators : 7 segment-38mm display 24. Car Operating Panel : Partial Height with ATS-IN 25. Other Features Battery Operated Emergengy Alarm and Light . OSG Electronic Switch .Call Registration LEDs, 2 Station Intercom system, Full-height Infra -red Light curtain Door Safety. Automatic Rescue Device . Lift Annoucement System, Pit Ladder, Door Frames on all Landings, 2 hours Fire-rated Landing doors, Buffer Rails. Note: i. Rate should include the cost for obtaining lift operating license from the competent authority and rectification of technical defects as pointed out during the inspection by licensing authoruty ii. Approved Brand/Manufactures-All the lift Manufactures as approved under category-A of CPWD works manual.

RAJSHEKHAR CONSTRUCTIONS PVT. LTD.

Shree Gautam Construction Co Ltd