Development of Childrens Park and Open Air Gym at Municipal Committee Basohli.

Amount

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables, etc. (not exceeding 1.5m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms including getting out excavated earth incl. disposal of surplus excavated earth as directed by Engineer-in-charge, including all leads and lifts. a) All Kind of soil.

Providing and laying cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: a) 1:4:8 (1 cement:4 coarse sand:8 graded stone aggregate 40mm nominal size).(including all leads and lifts carriages of material by MT / HL)

Brick work with common burnt clay (non modular) bricks of class designation 7.5 in foundation and plinth including curing in cement mortar 1:4 (1 cement:4 coarse sand). (including all leads and lifts carriages of material by MT / HL)

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. a) In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. a) With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/ liter

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge.

Supply and laying (River Bed Material) R.B.M. including watering ramming and consolidation manually capacity including all leads and lifts carriage of material by M.T. / H.L (complete job).

Supplying and stacking of good earth at site including royalty (earth measured in stacks will be reduced by 20% for payment) (including all leads and lifts carriages of material by MT / HL)

Providing and fixing M.S. flat iron tree guard 60 cm dia. and 2 m high above ground level formed of 4 nos. 25x6 mm, 2.25m long and 8 nos. 25x3 mm 2 m long vertical M.S. flats riveted to 3 nos.25x6 mm MS flat iron rings in two halves, fixed together at site with required 6 no. of 8 mm dia. and 30 mm long bolts including painting two coats with paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD/PWD/any other approved name The tree guard shall be suitably fixed to the ground by embedding four legs of the tree guard in pits of suitable dia. and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction on direction of Officer-in-charge.

(Air Walker) :Providing, designing and fixing of air swing in pair of size 1100x550x1480 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia at pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated. All pipes are welded with joints as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all wielding points prior to finishing. Pedal and base plate cover shall be made of plastic with rounded edges to prevent any impact of injury and UV resistant. Bearing used shall be maintenance free, duly oil sealed and self-lubricated. All open ends of pipe to be closed by GI LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J-shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, color on meta, seat and base cover plate and fixing of equipment.

(Horse Rider Station: Providing, designing and fixing of horse rider station of size 1000x600x1200mm fabricated with main post of 114mm dia and 2.5mm thick and .5mm thick and rest of the pipe 40mm dia at pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated. All pipes are welded with joints as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all wielding points prior to finishing. Pedal and base plate cover shall be made of plastic with rounded edges to prevent any impact of injury and UV resistant. Bearing used shall be maintenance free, duly oil sealed and self-lubricated. All open ends of pipe to be closed by GI LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J-shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, color on meta, seat and base cover plate and fixing of equipment.

(Leg Press) :Providing, designing and fixing of Leg press in pair of size 2000x550x1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia at pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated. All pipes are welded with joints as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all wielding points prior to finishing. Pedal and base plate cover shall be made of plastic with rounded edges to prevent any impact of injury and UV resistant. Bearing used shall be maintenance free, duly oil sealed and self-lubricated. All open ends of pipe to be closed by GI LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J-shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, color on meta, seat and base cover plate and fixing of equipment.

(Exercising Bar) :Providing, designing and fixing of Exercising Bar of size 1800x600x1700 mm fabricated with main post of 114mm dia and 2.5mm thick allat pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated. All pipes are welded with joints as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all wielding points prior to finishing. Pedal and base plate cover shall be made of plastic with rounded edges to prevent any impact of injury and UV resistant. Bearing used shall be maintenance free, duly oil sealed and self-lubricated. All open ends of pipe to be closed by GI LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J-shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, color on meta, seat and base cover plate and fixing of equipment.

(Arm Wheel) :Providing, designing and fixing of Arm Wheel in pair of size 1800x600x1700 mm fabricated with main post of 114mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated. All pipes are welded with joints as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all wielding points prior to finishing. Pedal and base plate cover shall be made of plastic with rounded edges to prevent any impact of injury and UV resistant. Bearing used shall be maintenance free, duly oil sealed and self-lubricated. All open ends of pipe to be closed by GI LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J-shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, color on meta, seat and base cover plate and fixing of equipment.

(Cycle) :Providing, designing and fixing twister of rowing machine of size 850mmx490mmx1300 mm fabricated with main post of 114mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated. All pipes are welded with joints as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all wielding points prior to finishing. Pedal and base plate cover shall be made of plastic with rounded edges to prevent any impact of injury and UV resistant. Bearing used shall be maintenance free, duly oil sealed and self-lubricated. All open ends of pipe to be closed by GI LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J-shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, color on meta, seat and base cover plate and fixing of equipment.

(Waist and Back Relaxer) :Providing, designing and fixing of waist and back relaxer of size 1050x830x1500 mm fabricated with main post of 114mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated. All pipes are welded with joints as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all wielding points prior to finishing. Pedal and base plate cover shall be made of plastic with rounded edges to prevent any impact of injury and UV resistant. Bearing used shall be maintenance free, duly oil sealed and self-lubricated. All open ends of pipe to be closed by GI LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J-shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, color on meta, seat and base cover plate and fixing of equipment.

(Twister Tripple) :Providing, designing and twister of size 1400x1400x1350 mm fabricated with main post of 114mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated. All pipes are welded with joints as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all wielding points prior to finishing. Pedal and base plate cover shall be made of plastic with rounded edges to prevent any impact of injury and UV resistant. Bearing used shall be maintenance free, duly oil sealed and self-lubricated. All open ends of pipe to be closed by GI LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J-shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, color on meta, seat and base cover plate and fixing of equipment.

MultiPlay System Area: 8mx9m Safe Area:9mx11m 1. Sq. Deck 5’ ht 1.The platform should be made up of Fiber Reinforced Plastic with anti-skid surface with thickness of 4-5mm. The top canopy is made of Fiber Reinforced Plastic with a minimum thickness of 2-3mm. Roto flag is attached on top. 2.Square Deck 3’ ht with Canopy: The platform should be made up of Fiber Reinforced Plastic with anti-skid surface with thickness of 4-5mm. the top canopy is made of Fiber Reinforced Plastic with a minimum thickness of 2-3mm. roto flag is attached on top. 3.Bowl Slide 3’ ht: The bowl slide chute should be made up of fiber glass reinforced plastic (FRP) molded one and is of attractive color and shade. The design of FRP bowl slide has minimum permissible joints suitable for children such that child does not fall down while sliding down. The FRP slide is 3-4mm thick. There is a suitable handgrip on the side of the slide. The landing support is made up of 25 NB GI pipes. The slide entry is also made of LLDPE in Rotational molding process. 4.FRP Bridge 8’ Long: The FRP Bridge should be made from Fiber Reinforced Plastic of 4-5mm thickness. It has railing made from Rotational molding process with support of 20 NB GI pipes. 5.FRP Tunnel 6’ Long: The tunnel should be a pipe shaped module of specific dia made from Fiber Reinforced Plastic of 3-4mm thickness. 6.Swinging Bridge 8’ Long: The swinging bridge is made of rotational molded planks and is suspended with galvanized chains. The frame is of 80 NB pipes with railing made from LLDPE & is supported by 20 NB GI pipes. 7.Spiral Slide 5’ height: Spiral slide chute is made of fiber reinforced plastic having shell thickness of 4-5mm. The slide is supported on 80 NB GI pipe. The landing module is supported by 20 NB pipe. The railing is made up of LLDPE in Rotational molding process. It is support by 20 NB GI pipe. 8.FRP Ladder: The ladder is made up of FRP with a thickness of 3-4mm. The top surface of the ladder should be such that it should not deserve any kind of skiddy movement. 9.Rock Climber 5’ ht: The rock climber is made up of Fiber Reinforced Plastic (FRP). The rocks are molded on same platform. The climber is supported by 25 NB pipe at the bottom for ground support. 10.Wave Slide 5/ ht: The wave slide chute is made up of 4-5 mm thick of Fiber Reinforced Plastic. The wave shape is given in such a manner that it will not give any jerk or bump to the rider. Rotational molded slide entry is provided at top of the slide. The chute has its end such as it causes safe landing of the child. The landing portion is horizontal with respect to the ground. The supports provided are made up of25 NB GI pipe. Foundation: The equipment is required to be fixed in open ground which may include excavation of earth and suitable concrete foundation to bear the load of the equipments with the children. Besides adjoining area has to be filled with sand to prevent the children from getting hurt. The filling of the sand should be minimum of 6 inches. Work has to be completed as per direction of the engineer-in-charge and specified notes.

FOUR SEATER ARC SWING 1.80 NB pipe bended & welded together to form a strong frame to with stand both the pitching & yawing moment. The with a flange & ISA 80 NB pipe is hot dip galvanized pipe of height 2900 mm conforming to IS 1239 with GI thickness of 60u. 2. 50 NB Top Pipe with two Arc Swing Flanges welded at both its ends. Pipe can with standing torsional stress created due to swinging motion. These 50 NB top pipes (2 Nos. for Four Seater Arc Swing) are hot dip galvanized pipe of length 2950 mm conforming to IS 1239 with GI thickness of 60u. 3. Special swing clamps made up of two parts are joined together with M6 Allen bolts along with S-Hook & a specially designed swing pin. The S-Hook is specially designed to house a bearing for smooth & noiseless swinging. The clamps are made from injection molded Nylon-6 plastic, FOUNDATION AND INSTALLATION: the equipment is required to be fixed in open ground which may include excavation of earth and suitable concrete foundation to bear the load of the equipment’s with the children. Besides adjoining area has to be filled with sand to prevent the children from getting hurt. The filling of the sand should be minimum of 6 inches. Work has to be completed as per direction of the engineer-in-charge and specified notes.

MULTI SEATER SEE-SAW 1.Ergonomically designed Rotational Molded seat should be 300 minimeterx190milimeterx70milimeter. 2.See saw Lever should be made from 80 NB Galvanized Pipe conforming standards IS 1239 with strong load carrying capacity.4. See Saw stand should be with special Nylon-6 bush enclosed in a seamless pipe hinged to 50 NB Support pipe. The stand is fixed with ISA for strong foundation grip. 5. The roto products should be manufactured using material LLDPE (Linear Low Density Polyethylene) of Grade-36RA045 (Food Grade Plastic) with density 963 kg/m. The material is added with antioxidant & 12% UV for protecting the product from color fading. The material is tested with weatherability test, carbon test, M.F.I. (Melt Flow Index) test, fatigue test. The mold is fixed to three arm bi-axial rotational molding machine & kept in the oven for about 20 minutes up to temperature of 180-210 Degrees. The overall product obtain is a seam – less to ensure perfect blend of uniform thickness & durability. FOUNDATION AND INSTALLATION: the equipment is required to be fixed in open ground which may include excavation of earth and suitable concrete foundation to bear the load of the equipment’s with the children. Besides adjoining area has to be filled with sand to prevent the children from getting hurt. The filling of the sand should be minimum of 6 inches. Work has to be completed as per direction of the engineer-in-charge and specified notes.

Carriage of the following materials by Mechanical Transport from source to site of work incl. loading, unloading and stacking complete :- a) Sand from Kathua for an average lead of 80.00 Km. by M.T. b) Stone aggregate (Crusher bajree) below 20mm nominal size from Kathua for an average lead of 80.00 Km. by M.T. c) Bricks from Kathua for an av. lead of 80.00 km. by M.T.

Soni Construction

ARJUN SONI GOVT CONTRACTOR

SUNITA SONI