GE/PKT-68/2019-20

Amount

Taking down chowkats or frames n. exc 1.5 Sqm each (without takaing off shutters) from frames complete all as specified and directed.

Taking down chowkats or frames exc 1.5 Sqm to 4.00 Sqm each (without takaing off shutters) from frames complete all as specified and directed.

Demolition of brick work built in cement mortar and removing unserviceable material exc at distance 100 mtr complete all as specified and directed.

Demolition of cement concrete(unrinforced), in any position and paving n.exc. 15 cm thickness( below or above ground level) including tile/ terrazzo floor complete all as specified and directed.

Taking down cement plaster from wall / ceiling of any description including terrazzo skirting/dado on brick or stone walls etc including raking out joints, hacking for key and scrubbing down with water etc.all as specified and directed.

M & L pressed steel frame of PBI sheet 1.25 mm thick (size of frame 125 x 60 mm) for doors with one or more rebates including necessary lugs, hinges, lock/ strike plate , hold fast etc complete all as specified& directed .

S&F steel window/Ventilator factory made box type and shutter (double shutter both side) with sash bar made out of section using flash butt welding, hinges shall be provided to both shutters complete including all fittings including grills, glazing (glass pane) , guaging(wire mesh) and two coat synthetic enamel paint over a coat of red oxide primer all as per drg No CEPZ/TD/245/01 Sh 1/1, CEPZ-TD/246/01 Sheet 1/2 and Sheet 2/2 all as specified and directed by Engr-in-Charge.

S & F 30 mm flush shutters,solid core construction, with block board core and plywood face panels, commercial type on both sides and with lipping etc fixed to chowkhats as spcified and as directed..

S&F mild steel barrel tower bolt 150 mm long stove enameled black ,with bright bolt and fixed complete all as specified and directed.

S&F mild steel sliding door bolt plate type, stove enameled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 300mm long complete all as specified and directed.

S&F mild steel pressed handle oval type stove enameled black 150mm long complete all as specified and directed.

M&L for brick work with sub class 'B' burnt brick, straight or curved or plan exc 6 mtr mean radius built in cement mortar 1:6 in one brick thick wall complete all as specified and directed.

M&L for brick work with sub class 'B' burnt brick, straight or curved or plan exc 6 mtr mean radius built in cement mortar 1:6 in one brick thick wall but except bricks (old brick reuse recd from demolition) complete all as specified and directed.

Dismantling timber scantling 40 Sq cm and over in section, in any position framed work complete all as speified and directed.

S & F mild Roof truss(framed), trussed,purlin, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or fat section) including distance piece, cleats etc. complete all as specified and directed.

Dismantling old plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings etc complete all as specified and directed.

M & L for Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L for Pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall/for vellygutter , fixed with self tapping screws in ridge as specified & directed.

M & L for 50 mm thick PCC 1:2:4 type B-1 using 20 mm graded aggregates as in floor/ plinth protection/ path etc finished even and fair complete all as specified and directed.

M&L for three coat of white wash on wall incl prepration of new plastered surface etc complete all as specified and directed.

M&L for providing PCC type B-1, 1:2:4 using 20mm graded stone aggregate in copings, water throughs,backfilling of chowkhets, holdfast,bed blocks of truss/purline and like incl weathering, slightly rounded or chamferred angle and throating complete all as specified and directed.

Preperation of old steel surface and applying two coat of synthetic enamel paint over 10cm width or girth complete all as specified and directed.

Preperation of new wooden surface and applying two coat of synthetic enamel paint over and including a coat of pink primer complete all as specified and directed.

M & L for plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in sub base of floor 75 mm thick or as specified and directed.

S & F mild steel plates (Plain or chequered) channels, square cut or notched (ordinary or counter sunk) forming holes, without any attachment of Fe-410-0 W (Gde E-250 quality) -A complete all as specified and directed.

S & F Mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nuts length of bolt exc 5 cm but n.exc 10 cm and dia of neck 5 to 10 mm) as directed by Engr-in-Charge

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

Demolation of Stone slabs and tiles of any description or thickness in floors laid bedded and pointed in any mortar, aprons etc complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. nexc 10 sqm area on plan and n exc 1.5 m in depth and getting out any type of soil etc complete all as specified and directed.

M&L for PCC 1:5:10 type E-2 using 40mm grded crushed stone agg as in fdn filling and mass concrete complete all as specified and directed.

S&F TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips for reinforcement complete all as specified and directed.

All as per item no. 31.00 here-in-before but 8 mm dia as in stirrups.

M&L for form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and similar work nexc 20cm thick but exc 10cm for fair finished surface complete all as specified and directed.

M&L for form work to edges of concrete flats , break in floors, openings in concrete wall , floors and roofs and sides of RCC/PCC bends in walls fair finished surface complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone agg) as in floor sub base for receiving tiles etc complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars,dovetailed or welded etc complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2((40 mm graded agg) as in plinth protection finished even and fair etc complete all as specified and directed.

S&F factory PVC solid door shuter 30mm thick (style) consisting of frame made out of MS tubes for top, lock and bottom rails M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm stuck inside with solvent cement for syiles and plain colour pvc sheet for top rail, lock rail and bottom rail panelling of plain colour sheet to be fitted in the MS frame welded/sealed to the stiles and rail with suitable PVC sheet beading and jointing togather with solvent cement at site as per specification & drawing.

S&F factory made pvc door frame of size 50mmX47mm with a wall thickness of 5mm made cut of extraded 5mm pvc foam sheet measured at corners and jointed with 2 nos of 150mm long bracket of 15X15mm square tube. The verticle door profile to be reinforced with 19X19mm MS square tube of 19 guage EPDM rubber gascate weather seal to be provided throught the frame. The frame to be fixed to the wall using MS screw of 65/100mm hold fast complete all as per manufactures specification & all as directed by Engg-in-charge

S&F Aluminium anodied, barrel tower bolts of extruded section 125 mm long etc complete all as specified and directed.

S&F Aluminium handles, cast type, anodised 125 mm long etc complete all as specified and directed.

S&F stainless steel but hinges medium weight cold rolled 100mm long etc complete all as specified and directed.

M&L for three coat of white wash on ceiling including preparation of new surface etc complete all as specified and directed.

Returning, filling including spreading levelling, watering and well ramming in layers nexc 25cm complete all as specified and directed.

Removal of excavated soil to a distance nexc 50m and depositing where directed at a level nexc 1.5m above the starting point complete all as specified and directed.

S&F PVC flushing cistern 10 ltrs capacity low level PVC valveless, syphonic action type, white, with inlet, ball valve, float and handle including brackets and connection to WC and flush pipe complete all as specified and directed.

S&F PVC connection 450mm long with PTMT nuts screwed for iron pipe of 15mm bore complete all as specified and directed.

S&F viterous china squatting pan, Orissa pattern, size 580x440 mm white, with integral foot rest etc including fixing in PCC (1:3:6) complete all as specified and directed.

Material and labour 75 mm thick for PCC 1:4:8 type D2 (40 mm graded stone agg) for sub base for floor/plinth protection etc all as specified and directed

S&F Rotational moulded polyethylene PVC water storage tank 1000 ltr (Cylindrical vertical with closed top) ISI marked hoisted and fixed in position all as specified incl ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia icluding tank nipple 20mm dia etc complete all as specified and directed.

S&F Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors 100 mm bore etc complete all as specified and directed.

All as per srl item no. 51.00 here-in-before but 75 mm dia complete all as specified and directed.

S&F Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to wall 75 mm bore etc complete all as specified and directed.

S & F CI Bends (any radius), diminishing pieces or tapers (larger bore measured) suitable for 100 mm bore pipes etc complete all as specified and directed.

S & F 100 mm CI Bends (any radius) with duck's foot or heel rest etc complete all as specified and directed.

S&F 100 mm branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches etc complete all as specified and directed.

S& F 75 mm dia cast iron cowls etc complete all as specified and directed.

M&L for non skid ceramic tiles coloured 7 to 8mm thick (square or rectangular) area of each tile exc. 0.11 Sqm but not exc 0.18 Sqm in floors set and jointed in neat cement slurry and pointed in white cement to match the colour over and including 15 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including screed bed in CM 1:4 ,10 mm thick etc complete all as specified and directed.

M&L for hard core of broken stone or boulder of gauge n.exc 63mm deposited,spread and levelled in layers n.exc 15 cm watered and well rammed to a true surface complete all as specified and directed.

S&F Cast iron floor trap with dia of outlet 75 mm CP grating including jointing to waste pipe fixed in PCC M-15 (Nominal mix) complete all as specified and directed.

S&F Brass CP mixer wall/basin for mixing hot & cold water screwed down for 15 mm dia iron pipe and fixed complete all as specified and directed.

S&F 15mm CP fancy type long nose Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, high pressure screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

S&F angle cock/stop valve cast copper alloy with crutch or butterfly handle, screwed down, high pressure, screwed for iron pipe 15mm bore complete all as specified and directed.

Supply, laying and testing GI water tubing, 40mm dia, medium grade, ISI marked with screw and socket joints with all fittings, fixtures like bend, sockets, unions, nipples etc laid in trenches, floor, including making alterations of existing tubing if necessary complete all as specified and directed.

Supply, laying and testing GI water tubing, 25mm dia, medium grade, ISI marked with screw and socket joints with all fittings, fixtures like bend, sockets, unions, nipples etc laid in trenches, floor, including making alterations of existing tubing if necessary complete all as specified and directed.

Supply, laying and testing GI water tubing, 20 mm dia, medium grade, ISI marked with screw and socket joints with all fittings, fixtures like bend, sockets, unions, nipples etc fixed to wall or laid in trenches, floor complete all as specified and directed.

Supply, laying and testing GI water tubing, 15 mm dia, medium grade, ISI marked with screw and socket joints with all fittings, fixtures like bend, sockets, unions, nipples etc fixed to wall or laid in trenches, floor complete all as specified and directed.

M&L for rendering 15 mm thick on fair face of the brick work in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering CM (1:6), 15mm thick on other than fair faces of brick work finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 05 mm thick on concrete ceilling surface in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed.

Cleaning of all foreign material such as fungus, mass, dust etc by brushing and dusting, sprinkling water on surface, surface shall be levelled with bending layer of 20 mm thick in CM (1:4) mixed with water proofing admixture as per manufacturer's insturctions and applying Polymer APP modified membrane with non-woven polyster reinforcement/mat with thermal insulation with white mineral gravel finished on upper side of weight not less than 3.5 kg/sqm and thickness not less than 3mm laid by torch application method with overlap 100 mm on length side and 100 mm on the width side over and including a coat of hot blown bitumen 85/25 @ 1.2 Kg/sqm on prepared surface complete all as specified and directed

S&F shower arm 15 mm size, 195 mm long with bend of 45 degree with flange of PTMT any colour. (minimum weight 40 gms complete all as specified and directed.

S&F chromium plated brass tublar towel rail, 20mm dia, 60cm long between flanges type D, complete all as specified and directed.

S&F shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minium weight 300 gms) complete all as specified and directed.

S&F vitreous China wash basin,ovel shape counter sunk type white or in matching colour of tiles ,size 550x450 mm excluding taps,but including 32 mm dia waste coupling chromium plated brass and PVC waste pipe 750 mm long( Minimum), chain and plug and porcelain stopper, brackets for fixing any size, including cutting for and pinning in ends or erecting stand complete all as specified and directed.

S&F Half stall Vitreous China urinals, (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (inclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe complete all as specified and directed. (Minimum weight 60gms)

S & F 100 mm dia cast iron sanitary connection socket to fit WC outlet etc complete all as specified and directed..

M & L for RCC 1:1.5:3 with using 20 mm graded stone agg for foundation , inclu raft ,footing, foundation beam, plinth beam bases for column etc complete all as specified and directed.

M & L for RCC 1:1.5:3 with using 20 mm graded stone agg for column, pillars, piers complete all as specified and directed.

M&L for RCC 1:1.5:3 using 20 mm graded aggregate 20mm as in slab supported on walls, beams, column in floors, roofs, benching, balconies, cacopies, deck slabs etc complete all as specified and directed.

M&L for RCC 1:1.5:3 using 20 mm graded stone aggregate as in lintel /lintal beam/beam up to 1.5m clear span including form work complete all as specified and directed.

M&L for cement concrete in foundations, fillings and mass concrete type D-2, 1:4: 8 (40mm graded stone agg) complete all as specified and directed.

M&L for form work to side of concrete foundation , footing base of column, raft and raft beams, side and soffits of foundation and plinth beams rough finished and flat surface of concrete etc complete all as specified and directed.

M&L for form work to side of pillars, post, strut , pier, col rough finished and flat surface of concrete etc complete all as specified and directed.

M&L for form work to sides and soffits of floor or roof beams, beam haunching , girders, bressummers, lintels, cantilever, shelves inclu support overhangs rough finished and flat surface of concrete etc complete all as specified and directed.

M&L for form work to edges of concrete slabs, flat complete, rough finished surfaces of concrete n exc 20cm wide complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone agg.) in bed blocks, foundation of column etc complete all as specified and directed.

S&F Steel work in tublar roof trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to I.S.1161-1979 grade St-240 all as specified and directed.

M&L for applying two coats of synthetic enamel paint over and including a coat of red oxide primer on new steel surfaces over 10 cm width or girth including preparation of surface complete all as specified and directed.

M & L for 100 mm thick plain cement concrete type D-2 1:4:8 (40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade and including 25 mm thick sand cushion complete all as specified and directed

M&L PCC (1:2:4) type B-1(20 mm graded stone agg. ) as in floor, 50mm thick, finished even and smooth with out using extra cement complete all as specified and directed.

S & F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n. exc 5 cm long and 11 to 15 mm diameter of neck etc complete all as specified and directed

S&F MS framed work such as doors, gates, road sign board, of angle or other section, with gusset plates, rails, braces, etc complete , drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging, also fastening and fixing complete all as specified and directed

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out soft/loose soil etc complete all as specified and directed

M & L for cement concrete coloured chequred tile 30cm X30cmX 25mm thick machine pressed set and jointed and pointed in neat cement slurry in floors with grey cement and pigment as required (coloured made in PVC mould with vibration process) prelaminated for glossy finish laid over and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for 100 mm thick concrete bed to drain pipes incl packing under and haunching against the sides of pipe after they are laid and tested in Cement concrete 1:3:6 Type C-2 for bore of pipe 160mm complete all as specified and directed

S&F unplasticisted PVC drainage pipe 160mm dia type 'B' with wall thickness 4mm (min) of pressure rating 4KN/Sqm laid in tranches and jointed with cement solvent including testing complete all as specified and directed.

M&L precast cement concrete type B-1 1:2:4 (20mm graded stone agg) in cover slabs, set in CM 1:4 etc complete all as specified and directed

Cutting into existing manholes for connecting new drains internal dia 150 to 160 mm making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed

Material and labour for Cement concrete 1:2:4 type B1 (20 mm graded stone agg) as in benching of manholes and similar work incl form work and finishing all exposed surfaces all as specified and directed

M&L for brick with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar (1:4) in one brick thick wall complete all as specified and directed.

M&L for RCC M-30 design mix as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M30 design mix (20mm graded stone aggregates) as in Columns, pillars, piers, posts and struts complete all as specified and directed

M&L for RCC M30 design mix (20mm graded stone aggregates) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M&L for RCC M30 design mix (20mm graded stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 using old sized bricks in one brick thick wall complete all as specified and directed.

M&L 75mm subbase cement concrete type B- 2 1:2:4 (40mm graded stone aggregate) as in floor finished even and smooth without using extra cement complete all as specified and directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering comlete all as specified and directed

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces using CM 1:4 finished even and smooth w/o using extra cement all as specified and directed

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces using CM 1:6 finished even and smooth w/o using extra cement complete all as specified and directed

M&L for preparation of new plastered surfaces of wall applyng two coats of cement base paint over and including a coat of primer complete all as specified and directed including curing before and after providing of each coat complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and treating the surface with a coat of cement based wall care putty to make surface smooth including two coats of distempering on wall with distemper oil emulison (any tint) complete all as specefied and directed.

S&F for rotational moulded polyethylene water storage tanks 500 ltr capacity (cylindrical vertical with closed top) ISI marked hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

M&L for granite (Black 18/19mm thick) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F Powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.) for each shutter complete all as specified

S&F Powder coated anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F solid PVC door/window wooden grain printed frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube, supplying and fixing in operating as per specifications given in SSR 2010 (Part-II) complete all as specified and directed.

S&F factory Made Solid PVC flush door shutter with wood free EPS core, 28 to 30mm thick (stiles), with 2mm thick prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F aluminium alloy, anodised 250 mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F aluminium anodised, 150 mm long barrel tower bolt of extruded section complete all as specified and directed.

S&F 150 mm long aluminium handles , cast type, anodised complete all as specified and directed.

S&F extruded aluminium alloy with galvanised mild steel pin anodised Butt hinges 100mm type B-21 complete all as directed

S&F Sheet glass 4mm thick n. exc 0.5sqm each pane in doors/windows complete all as specified and directed

S&F Door closer hydraulically regulated, CI body designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F 40mm Gun-metal, gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 25mm Gun-metal, gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 15mm Gun-metal, gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply and fix concealed stop cock chromium plated fancy type cast copper alloy screwed down high pressure ,with crutch or butterfly handle screwed both ends for iron pipe or for union of 15 mm bore complete all as spd & directed

S&F 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as spd & directed

M&L for Dark shaded Vitrified Endura tiles 30cm x 30cm x 10mm thick, set jointed and pointed in cement slurry mixed with pigment to match the shade in floors pointed in white or coloured cement along with screed bed of 15mm thick in CM 1:4 complete all as specified and directed

M&L for providing cement concrete type B0(12.5mm graded stone aggregate) in kerbs(rubber moulded table vibrated smooth finish or mud stops, rounded of chamfered on edges water toughs and the like including weatering slightly/rounded or chamfered angles and throughting as directed

M&L for RCC 1:2:4 type B-1 nominal mix (12.5mm graded stone aggregate) as in slab supported on walls beams and columns in floors and roofs and shelves and the like complete all as spd & directed

M&L for providing precast cement concrete louvres and jallies, 25mm thick set in CM 1:4 type C0 1:3:6 (12.5 mm graded aggregate) (measured solid), including all mould- ings but excluding frame complete all as spd & directed.

Preparing surfaces of walls of plastered or unplastered surfaces on old surfces washing rubbing down and stopping of plastering surfaces with one coat putty and applying two coats of plastic emulsion paint complete all as spd & directed

S&F sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x460 mm and bowl size 410mmx330mmx 160mm complete all as specified and directed.

S&F Plate rack made of stainless steel 1.00 mm thick of size 600 mm (ht) x 900mm (width) x 250mm (depth) fixed to wall with and including nuts & bolts of suitable size for fixing in wall complete all as specified and directed.

S&F vitreous China wash basin, white or in matching colour of tiles , flat back, size 550x450 mm excluding taps,but including 32 mm dia waste coupling chromium plated brass and PVC waste pipe 750 mm long( Minimum), chain and plug and porcelain stopper, brackets for fixing any size, including cutting for and pinning in ends of brackets or erecting stand as directed by Engineer-in-Charge

S&F Pillar taps, cast copper alloy 15 mm bore, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed as specified and directed.

Supply and fix CP bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 15mm size and fixed as specified and directed.

Cutting holes exc 150 Sq cm but not 400 sq cm into or through brick walls built in any type of mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required.

Material & labour for Cutting existing steel tubing for alterations or additions (Each cut measured) including threading of existing pipes placing new Tee of required size tapping connection for new pipe linecomplete all as specified and directed by the Engr-In-Charge. (cost should be inclusive of earthwork)

Construction of brick masonry valve pit chamber of inner dimension 450x450x700 mm suitable for valves up to 100 mm dia size, with PCC 1:4:8 type D-2 for foundation, brick work in CM 1:6 in one brick thick wall, rendering on internal surface & upto 15 cm below GL on external surface in CM1:4, 15 mm thick, 25mm thick coping in PCC1:2:4 type B-1, including necessary earth work, P/O MS sheet cover of thickness 3.15 mm on 50x50x6.0 mm angle iron frame with locking arrangement, including one 50 mm lock, painting over MS surfaces with two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as spd & directed

Taking down old unserviceable copper/aluminium point wiring (light, fan, socket , power socket and bulk head fittings) on surface wiring on wooden batten/casings & caping complete, including fixture and fittings such as switches, ceiling roses,pendents holder, regulators and sockets by unscrewing carefully from boards etc and making good disturbed surfaces of walls, as per existing finishes complete all as spd and directed.

M & L for point wiring for one light/one fan controlled by one switch with 1.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable with and including PVC concealed conduit heavy duty 20 mm dia having thickness not less than 1.8 mm with all fittings including anodised pressed steel sunken box having thickness not less than 2mm with 3mm thick bakelite laminated sheet ISI marked for switches and sockets , including 1.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly, including cutting chiseling for concealed piping and making good disturbed surface to match with the existing surface complete all as specified and directed.Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green)

All as per srl item No 151.00 here-in-before but for 5 pin 5 amps socket outlet on independent board complete all as specified and directed.

All as per srl item No 151.00 here-in-before but for 5 pin 5 amps socket outlet on same board with other switch complete all as specified and directed.

M & L for point wiring with 2.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable in and including PVC concealed conduit heavy duty 20mm dia having thickness not less than 1.8 mm with all fittings including anodised pressed steel sunken box having thickness not less than 2mm with 3mm thick bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 2.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly including cutting chiseling for concealed piping and making good disturbed surface finishing the surface to match with the existingsurface complete all as specified and directed.Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black,Earth- Green)

S & F socket outlet 2 in 1, 3 pin 5 amps flush type 240 volts complete all as specified and directed.

S & F switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed.

S & F switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed.

S & F socket outlet 2 in 1, 5 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S & F switch socket combination 2 in 1, 5 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S & F lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

S & F ceiling rose 65 x 50mm three terminals complete all as specified and directed.

Supply and fixing ceiling fan regulator electronic socket type 5 stage speed variation ISI marked complete all as specified and directed.

S&F in replacement sleek LED mirror light fitting 2 feet long 1x10 W including LED tube 2 feet long of same make having ballast , bipin holder, connector block etc. complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 Sqmm 3 core complete all as required at site or directed.

S&F Decarative ultra slim wall mounted linear LED 10 W lighting fixture with co extraude polycorbanate complete all as specified by Engg-in-charge.

S & F in replacement of CFLs with LED smart Lamp, B22 type ,14 watt, complete all as specified and directed.

S & F CFL fitting 1x 11 W atractive wall/ceiling mounted type with metalic channel and white reflector suitable for mirror fitting with ballast complete with all accessories pre- wired twisted flexible copper conductor cable with suitable size complete all as spd & directed

S & F energy saving decorative LED box type with Led Rod 20 watt (4 Feet), 230 volts, 6500 K energy efficient tube light fitting extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories prewired and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings. (Note power factor should not be less than 0.95) complete all as spd and directed.

M & L for sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 4 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases for fixing DB and making good distributed wall surfaces to match with existing specification .

M & L for sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases for fixing DB and making good distributed wall surfaces to match with existing specification .

M & L for MCB Single Pole 240 volts any rating from 20 to 40 amps, with rupturing capacity 10 KA, 'C' curveincluding providing thimble for out going cables complete all as spd & directed

M & L for MCB SPN 240 volts any rating from 6 to 40 amps, with rupturing capacity 10 KA, 'C' curve including providing thimble for out going cables complete all as spd & directed

M & L for MCB DP 240 volts of rating 32 amps with rupturing capacity 10 KA, 'C' curve including providing thimble for out going cables complete all as spd & directed

M & L for earthing complete with galvanised steel earth plate electrode , 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level)with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point , GI tubing 15 mm bore light grade protection pipe , GI watering pipe 20mm bore light grade with funnel and wire mesh , charcoal ,salt packed around the earth plate and PCC chamber in PCC 1:2:4 type B-1 with 3.15mm thick MS sheet cover including suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover including earth work in any type of soil , removal of surplus soil to a distance n.exc 50m and connecting , testing on completion complete all as shown on electric plate No 03 of SSR -2009 Part I complete all as specified and directed.(Note: Excavation and earth work is deemed to be included in the rates quoted).

S&F Storage type Electric water heater (Geyser) capacity 25 litrs BEE 5 Star rating PVC BODY with complete accesoiries complete all as spd and directed.

S&F stop valves, cast copper alloy, screwed down, high pressure with crutcher butterfly handle, screwed both ends for 15mm bore dia of pipe complete all as spd and directed.

S& F Bib taps cost copper alloy, fancy type with crutch of butter fly handle ,screwed down, high pressure screwed for 15mm dia pipe complete all as spd and directed.

Suplly, laying and testing 15mm dia GI pipes "Medium Grade" including fittings laid in wall or in ceiling or in floor complete all as spd & directed.

S&F PVC connection for hot & cold water 450 mm long, 15mm dia with brass adopters complete all as specified and directed.

M & L for providing/ cutting the round/ square hole of required size in wall finishing the same for distrubed surfaces complete all as spd and supply and fixing propeller type AC ventilating fans, Single phase, 230 volts 250 mm sweep complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 1.5 sqmm copper cable from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as spd and directed.

S&F in replacement sub Main Wiring with two PVC insulated unsheathed multistranded flexible copper conductor cable of size 2x4 sqmm and one PVC insulated multistranded unsheathed flexible copper conductor 4 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in and including non metallic PVC concealed conduit complete and making good to disturbed surface of wall/floor with cement mortar and finishes to match with existing surface all as specified and directed by Engineer-in-charge including taking down of existing un serviceable sub main wiring complete all as spd and directed.

S & F bldg secuirty light fitting energy saving high efficiency LED street light fitting 30 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 32 mm dia light grade GI pipe bent to shape having length not less than 1.5 mtr fixing with clamp etc and making connections using cord flexible 3 core copper cable of size 23/ .0076 from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage.

S&F exhaust fan double ball bearig complete 240/230 volts 300 mm sweep 230V single phase AC , 50 Hz with louvers Including all electrical connection, with flexible cable and cutting of hole to wall and making good the disturbed surface as per existing complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft/loose soil for laying of cable, pole foundation,stay,laying of pipe etc complete all as specified and directed.

Returning filling in, including spreading ,leveling ,watering and well ramming in layers not exc 25 cm thick complete all as specified.

M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable punned down upto 18 cm complete all as specified. Note: Punned thickness 18cm shall be considered for payment purpose.

M&L for Brick covering as mechanical protection to cable with well burnt sub class 'B' bricks old size, laid with length perpendicular to length of cable complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 mtr and deposting where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified.

M&L for XLPE insulated, armoured, heavy duty electric cable with aluminum conductor, 1100 volts grade, of cross-sectional area 10 Sqmm, 2 core including taking down of old UNSV cable complete all as specified.

S&F of GI tubing medium grade of 40mm nominal bore of pipe in trenches/under road/under culvert/ under paths/ under floor or wall/pole in new position with screwed sockets joints together with all tube fittings (such as bends, elbow, tees, short piece connections, back nuts, dimnishing piece, caps, plugs and union etc) complete all as specified and directed.

Dismantling of fencing wire of any type or any description, complete all as specified and directed.

Dismantling of RCC Posts, strut (Wood or Steel or RCC) etc. of any section including taking out embeded in concrete, brick and masonary portion and making good disturbed surface, complete all as specified and directed.

Dismantling structural steel work including doors gates but excluding framed truss etc complete all as specified and directed.

Site clearance by clearing away all grass vegetation, saplings, shrubs, brushwood,vegetation growth etc and removing rubbish up to 1.5 mtr away from the face of the wall along the perimeter of the wall to have clear working space complete all as specified and directed.

M&L for PCC 1:3:6 Type C-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed by Engr-in-charge.

S& F Galvanised Mild Steel Barbed Wire, 2 strand of 2 mm dia and barbed with 2mm dia barbs of 75mm spacing and straining and fixing to any type of standard rails straining bolt etc or tying with and including galvanised wire stapples or steel pins all as specified and directed. Note :- (Each line of wire & straining bolt shall be measured and paid separately.)

Fixing and restraining rescuring including making good staples old Galvanised Mild Steel Barbed Wire, and straining and fixing to any type of standard rails straining bolt etc or tying with and including galvanised wire stapples or steel pins all as specified and directed. Note :- (Each line of wire & straining bolt shall be measured and paid separately.)

S&F mild steel work as in post and struts in fencing incl cutting to shape as directed drilling holes, notching for wire etc, flat iron fillet for securing wire mess etc including necessary drilling, bolting etc and similar work conforming to Fe-290 grade E-165 with end bar shouldered and / or riveted or forged into spike, framed, complete all as specified and directed.

S&F framed work in doors or gates in angle or other section with gusset plates, rails, braces etc complete drilling for fixing and steel sheeting or other covering etc conforming to fe-290 Gde E-165 complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over and including one coat of red oxide primer on steel surfaces of any description, not otherwise described over 10Cm width or girth including preparation of new steel surfaces all as specified and directed.

M&L for applying one coats of synthetic enamel paint on steel surfaces of any description, not otherwise described over 10Cm width or girth including preparation of old steel surfaces all as specified and directed.

Excavating in post holes soft/loose soil(or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, etc complete all as specified and directed.

Notes :- (a) The contract sum shall be arrived at after deduction of amount of Schedule of Credit. (Rs. 30,487.00). (b) PERFORMANCE SECURITY :- (Refer condition 19 of IAFW-2249) The performance security for an amount equivalent to 5% (Five percent) of the accepted contract sum shall be delivered by the successful bidder within 28 days from the date of intimation letter of acceptance and all provisions shall be applicable as per condition 19 of IAFW 2249

M/S RUDRA CONSTRUCTION CO

RD Engineers

GANDOTRA CONSTRUCTION CO

kay gee construction co

M/S Raghuvanshi Builders

M/S SALARIA BUILDERS

V K Sharma and Sons