IMPROVEMENT TO COOK HOUSE OF AIRMAN MESS AND CONNECTED AREAS AND PROVISION OF MULTI PURPOSE SHED AT CERTAIN OMQ AND SMQ AREAS AT HQTC(U)

Amount

Surface dressing n exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in soft/ loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/ loose soil complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheeting 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/J hooks and bolts as reqd complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheeting 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/J hooks and bolts as reqd complete all as specified and directed.

M&L Machine pressed precast conctete glossy finish interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade and pointed with grey cement mixed with pigment to match complete all as specified and directed.

All as per item No 5.00 here-in-before but except paver block using/re-laying old serviceable interlocking paver block including taking down old paver block,levelling the surface as required at site complete all as specified and directed.

M&L 75 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) for hard standing including finishing the surface even and fair complete all as specified and directed.

M&L Plain cement concrete (1:3:6), type C2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

S&F mild steel tubular trussed, purlins, fencing posts,crane gantries rails and fastenings including special shaped washer etc complete using ERW or induction butt welded tubes Conforming to IS 1161-1979 grade St -240 including distance pieces, cleats , nut & bolt any size & length etc complete all as specified and directed.

S&F Mild steel screw bolts, diameter of neck in 16 to 20mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10cm and n exc 15cm long complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc1.5 m in depth and getting out in soft/ loose soil complete all as specified and directed.

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils in soft/loose soil complete all as specified and directed.

M&L for PCC type D2 ,1:4:8 (Using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for Providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) type C1, 1:3:6 ( 20 mm graded aggregate) and setting in mortar 1: 6 , complete in walls complete all as specified and directed.

M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L Sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L 100 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) for floor including finishing the surface even and smooth with using extra cement complete all as specified and directed.

M&L Coloured designed chequered cement concrete tiles of a size 300x300x25mm thick with white cement & pigment in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match and including a 15 mm thick screed bed of cement mortar (1:6) complete all as specified and directed.

M&L Preparation of new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide priming complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in Cement mortar 1:6, finished even and smooth with out using extra cement complete all as specified and directed.

M&L for Preparing new plastered surfaces and applying three coat of white wash on surfaces on walls complete all as specified and directed.

Taking down of chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from the frames) and set aside or removing from site complete all as specified and directed.

Taking down of chowkats or frames exc 1.5 sqm but n. exc 4.0 sqm each (without taking off shutters from the frames) and set aside or removing from sitecomplete all as specified and directed.

Taking down shutters of any description exceeding 1 sq. m but not exceeding 2.0 sq.m each complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sq. M but not exceeding 2 Sq. M each and refixing in same opening after easing and adjusting all as specified and directed.

S&F Factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws,etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in- Charge. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Glass shall be paid separately

S&F Factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Glass or wiremesh shall be paid separately

S&F factory made uPVC white colour fixed glazed window/ ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Glass shall be paid separately.

S&F Powder coating (minimum thickness of powder coating 50 micron) aluminium frame for partition, doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.

S&F Powder coating (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, sliding /side hung type without sash bars, aluminium sections weighing not less then 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and as directed. Note : sheet Glass and SS wiremesh shall be measured & paid separately.

S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F Mild steel, plain, black sheet in hearths; covering to door shutters; covering to door chowkats (frames);chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and as directed.

S&F 5.50mm thick sheet glass ordinary quality and glazing with EPDM rubber/ neoprene gasket etc exc 0.50 Sqm in each panes complete all as specified and as directed.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples including beads complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutter,with particle board core , 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and as directed.

S&F 150 mm alluminium anodised barrel tower bolts of stove enameled black, with bright bolt and fixed complete all as specified and as directed..

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed..

S&F 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F in repair 300 mm size mild steel rat tail rod pattern springs including roller and roller plate complete complete all as specified and as directed.

M&L Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed..

S&F in repairs Powder coated fancy type Stainless Steel curtain rod 25mm dia with suitable SS brackets with suitable wooden round base and fancy type end top matching to curtain rod of make as approved by GE complete all as specified and as directed. Note:[ Additional supporting bracket shall be provided if length is exceeding 1.2m and rate quoted shall include for the same ]

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc.,disposal of unserviceable materials, debris and rubbish to a distance complete all as specified and as directed.

M&L for Pre-cast cement concrete block masonry with solid blocks type C1, 1:3:6 ( 20 mm graded aggregate) exc. 10 cm in width and setting in mortar 1: 6 complete all as specified and as directed.

M&L for Providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) type C1, 1:3:6 ( 20 mm graded aggregate) and setting in mortar 1: 6 , complete in walls all as complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement including mixing of water proofing compound wherever required as per manufacturers instructions complete all as specified and as directed. Note: (WPC shall be measured & paid separately). .

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in Cement mortar 1:6, finished even and smooth with out using extra cement. complete all as specified and as directed.

M&L for Rendering 10 mm thick on fair faces of concrete surfaces in cement mortar 1:3 in ceiling of chajja,roof projection,shelve etc and finished even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound of approved quality complete all as specified and as directed.

Dismantling structural steel work including doors, gates and similar works but excluding framed truss etc complete all as specified and as directed.

S&F mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Conforming to Fe-290 Gde E-165 including distance pieces, cleats,nut & bolt any size & length etc complete all as specified and as directed.

M&L for Plain Cement Concrete Type B0 , 1:2:4 (using 12.5 mm graded stone aggregate) cast in situ in cills and other similar bands, plinth courses, parapets, copings, hold fast ,bed plates ,filling hollow section of pressed steel frame and the like including use and waste of form work,weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

Dismantling ceiling boards (fibre, pulp, insulation, etc or insulation boards/slabs/ blankets, any thickness, including cover fillets etc complete all as specified and as directed.

S&FGl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and as directed.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wiremesh complete with designer ceiling (with part ply,laminate and cove) complete all as specified and as directed. Note: Fillets, metal frame work and G.I. wire mesh paid separately.

M&L for two coats of distemper oil emulsion white or tinted incl over a coat of arclic primer with 1mm thick wall care putty, including preparation of new surface on ceiling complete all as specified and as directed.

Demolition of Stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Demolition of cement concrete(unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and as directed. General notes for Item No 61.00 to 63.00: All the debris / demolished material shall be removed from site to outside AF campus at contractors risk and cost in accordance with all applicable federal state and local regulations as and when directed by Engineer in charge.

M&L 75 mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) in plinth protection, finished even and smooth w/o using extra cement complete all as specified and as directed..

M&L for 40 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in flooring,finished even and smooth w/o using extra cement all as specified and directed.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound, grade 'A' complete all as specified and as directed.

M&L non skid ceramic tiles Coloured 7 to 8mm thick (square/rectangular) area of each tile exc 0.11sqm but n.exc 0.16 sqm, in in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed 15mm thick in CM 1:6 complete all as specified and as directed.

M&L Coloured Glazed Ceramic tiles 300 x 450 x 7mm thick on vertical surfaces such as skirting, dados and risers to steps etc including 10mm thick backing coat in CM 1:4 complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and including a 15 mm thick screed bed of cement mortar 1:6 complete all as specified and as directed.

M&L for Grinding with carborandum stones of 120 grit fitted in the machine in first phase and further second phase with carborandum of grit 220 to 350 and Oxalic acid powder shall then be dusted at 33 grams per square meter on the surface and the surface rubbed with machine fitted hessian bobs or rubbed hard with pad of woolen rags to kota stone slab, marble tiles, granite stone, terrazzo tiles etc. as in floor/ skirtng etc including cleaning the surfaces complete all as specified and as directed.

M&L RCC 1:2:4, type B1 using 20 mm graded stone aggregate as in pre-cast cover slabs for shelves and similar articles incl necessary form work set in CM 1:4 complete all as specified and as directed.

S&F Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and bindingwith and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L Granite slab work 18 to 20mm thick in floors steps, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over & including screed bed 15mm thick in CM 1:6 including cutting recess opening for the sink portion and embedding complete all as specified and directed.

M&L Granite slab work 18 to 20mm thick in floors steps, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over & including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for sand sand cushioning with clean river sand duly clear of residual , organic and deleterious materials spread evenly to uniform thickness complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying through mechinical means two coats of oil bound distember (white or tined) over a coat of approved primer to obtain uniform surfaces including making good the surface complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying through mechanical means two coat of exterior emulsion paint over one coat of primer on complete all as specified and directed.

M&L for preparing of new plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old decorated surface of walls including washing, rubbing down and stopping of distempered and painted surfaces and applying through mechnical means one coat of distemper oil emulsion complete all as specified and as directed.

M&L for preparation of old decorated surface on ceiling including washing, rubbing down and stopping of distempered and painted surfaces and applying through mechnical means one coat of distemper oil emulsion complete all as specified and as directed.

M&L for preparation of old decorated surface of walls including washing, rubbing down and stopping of distempered and applying through mechnical means one coat of cement paint complete all as specified and directed.

M&L for Preparation of old painted surface of any description not otherwise described wood and wood based surfaces over 10 cm width of girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for Preparation of old painted surface of any description not otherwise described steel surfaces over 10 cm width of girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for applying Bitumen blown any grade, applied hot, two coats, to concrete surfaces at the rate of 1.5 kg per sq m including cleaning the surfaces complete all as specified and as directed.

Dismantling water tanks exc 500 ltrs and n exc 1000 ltrs complete all as specified and as directed.

S&F Rotational moulded polyethylene water storage tanks of white colour triple layered (ISO certified) (cylindrical vertical with closed top ) hoisted and fixed in position all as specified in Sch “A” of capacity 1000 liter, including 20 mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed.

S&F in repairs Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore complete all as specified and as directed.

Taking up or down 15mm dia steel tubing connections, including cleaning for re-fixing or removal to store complete all as specified and as directed..

S&F Tubes, ‘Medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors of 20 mm bore pipe line, including cutting holes or grooves in brick wall/rcc and making good with cement mortar 1:3, complete all as specified and as directed.

Taking up or down 20 mm dia steel tubing connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

S&F Tubes, ‘Medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors of 15 mm bore concealed pipe line, including cutting holes or grooves in brick wall/rcc and making good with cement mortar 1:3, complete all as specified and as directed.

S&F in repairs 15mm long body bib taps long shank cast copper alloy with crutch or butterfly hadle secrwed for iron piper or for brass ferrule complete all as specified and as directed.

S&F in repairs 15mm fancy Pillar taps, cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repairs Stop valve / Angle cock 15mm bore fancy type chromium plated screwed down high pressure, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repairs PVC connection 15mm size 450mm long with CP PTMT nuts complete all as specified and as directed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

S&F in repairs Vitreous china wash down water closet (Pedestal pattern, ETWC), white including fixing bolts, 110mm PVC (SWR) 'P’ trap, Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets Flush pipe of polyethylene of low or higdensity or PVC 32 mm dia, for low level cistern complete all as specified and as directed.

S&F in repairs wash hand basin Vitreous china, light colour / white of size 565mmx420mmx140mm including brass chromium plated waste coupling, chain, plug, porcelain rubber stopper, brackets, 32mm bore PVC waste pipe of appropriate length inlcluding making necessary connections complete all as specified and directed.

S&F in repairs sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repairs Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms /40mm-60 gms) ccomplete all as specified and as directed.

Taking down drain water pipes including all fittings any size and pattern with fittings complete complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 110mm bore complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls110mm bore complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal with access door 75 mm bore complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 75mm bore complete all as specified and as directed.

S&F in repairs PVC (SWR) floor trap 75mm dia outlet, plain/hole with grating including jointing with solvent cement complete all as specified and as directed.

S&F PVC (SWR) bends any radius 75mm bore complete all as specified and as directed.

S&F PVC (SWR) bends any radius with access doors 75mm bore complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal with access door 75 mm bore complete all as specified and as directed.

S&F PVC (SWR) vent cowl 75mm bore complete all as specified and as directed.

S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solventcement and fixed in cement concrete complete all as specified and as directed.

Taking down carefully copper/aluminium point wiring (light fan socket or power) complete including fittings such as switches, ceiling rose, pendants, regulators, sockets, light fittings complete as directed and removing retrieved materials and making good the disturbed surface complete all as specified and as directed.

Taking down ceiling fan from ceiling, painting of ceiling fans complete, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and refixing of ceiling fan including provision of of cable from ceiling rose to fan connector complete all as specified and as directed.

M&L for taking out Geyser from the old location of any capacity, and re fixing along with fixing arrangement including required fixing materials in new location on any type of walls complete all as specified and as directed.

S&F in repair exhaust fan, steel body AC single Phase 230V of size 450mm sweep with, blades, and frame and louvers complete all as specified and as directed.

S&F Point wiring with cable of PVC insulated FRLS copper multistranded conductor 1.5 sqmm 1100 volts grade in and including heavy grade PVC Casing Caping Pipe ISI marked with all accessories and fixing arrangements on wall/ceiling/floor etc. including fixing top cover /PVC junction boxes fixing on wall surface for housing switches/sockets/regulators etc. with and including 1.5 sqmm PVC insulated multistranded copper earth continuity conductor connecting to the common earth dolly etc complete all as specified and directed for the following :-

One light point controlled by one single pole 5 Amps switch.

One fan/ exaust fan point controlled by one single pole 5 Amps switch.

One switch socket outlet point 5 Amps on independent board.

One switch socket outlet point 5 Amps on same board with other switches.

All as per item No 118.00 here-in-before but using copper conductor 2.5 sqmm PVC insulated unsheathed FRLS cable with copper conductor PVC Casing Caping Pipe ISI marked of size 2.5 sqmm PVC insulated unsheathed continuous earth continuity for 3 pin 15 amps switch socket outlet independently complete all as specified and as directed.

S&F Point wiring complete with Multi stranded copper conductor size 1.5 sqmm PVC insulated, unsheathed,FRLS cable , 1100 volts grade conforming to IS 694 multistranded , drawn in and including rigid PVC surface type conduit Concealed in walls/ floors/ ceiling etc with and including fixing of metal flush boxes of suitable size and modular white plate with frame for mounting of fittings, modular type switches, regulator and also including 1.5 sqmm PVC insulated unsheathed copper cable green in colour as continuous earth continuity conductor and connecting to earth dolly,cutting chasis to the wall s/ floors/ ceiling and repairing with existing surface after work ,complete all as specified and directed.

One light point controlled by one way switch.

One ceiling/Exhaust fan point controlled by one way switch.

One 3 pin socket point 5 Amps on independent board.

All as per item No 124.00 here-in-before but using copper conductor 2.5 sqmm PVC insulated unsheathed FRLS cable with copper conductor size 2.5 sqmmm PVC insulated unsheathed continuous earth continuity for 3 pin 15 amps socket outlet independently complete all as specified and directed.

S&F PVC ceiling rose 65 x 50 mm surface type with 3 terminals complete all as specified and directed.

S&F Modular swich one way 6 Amps, 230 volts complete all as specified and directed.

S&F Modular Fan step regulator, 120W - 2 module complete all as specified and directed.

S&F Modular socket, 6 Amps 2/3 pin combined two module, 230 volts complete all as specified and directed.

S&F Modular socket, 6 A/16 Amps 2/3 pin combined two module, 230 volts complete all as specified and directed.

S&F Modular swich one way 16 Amps one module, 230 volts complete all as specified and directed.

S&F Modular white cover suitable with frame 2 module complete all as specified and directed.

S&F Modular white cover suitable with frame 3 module complete all as specified and directed.

S&F modular white cover suitable with frame 4 module complete all as specified and directed..

S&F modular white cover suitable with frame 6 module complete all as specified and directed..

S&F modular metal flush board 1/2 module complete all as specified and directed.

S&F modular metal flush board 3 module complete all as specified and directed.

S&F modular metal flush board 4 module complete all as specified and directed.

S&F modular metal flush board 6 module complete all as specified and directed.

S&F in repair LED lights fitting 4 feet, 1 x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F Sub main wiring with Two single core PVC insulated FRLS cable with copper conductor multistranded 1100 volts grade 2.50 sqmm in and including non-metallic rigid PVC casing and capping and accessories and fixing arrangements fixed to surface on wall, floor or ceiling etc including 2.50 sqmm PVC insulated FRLS multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC casing capping and two run of copper conductor together taken as one length for measuring unit length complete all as specified and directed.

S&F Sub main wiring with Two single core PVC insulated cable with copper conductor multistranded 1100 volts grade 4.0 sqmm in and including non-metallic rigid PVC casing and capping and accessories and fixing arrangements fixed to surface on wall, floor or ceiling etc including 4.00 sqmm PVC insulated multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC Conduit and two run of copper conductor together taken as one length for measuring unit length.

S&F Sub main wiring with Two single core PVC insulated cable with copper conductor multistranded 1100 volts grade 6 sqmm in and including non-metallic rigid PVC casing and capping accessories and fixing arrangements fixed to surface on wall, floor or ceiling etc including 6.00 sqmm PVC insulated multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC Conduit and two run of copper conductor together taken as one length for measuring unit length.

Taking down ceiling fan circulators, sealing cable end, dismantaling blades, and removing fan including painting and refix the same including connecting up and provision of cable from ceiling rose or connector to fan complete all as specified and directed.

S&F in repair DB, TPN 12 ways, Double door type with 100 Amps MCB complete all as specified and as directed

S&F in repair Sheet metal enclosure, single pole and neutral 8 Way double door type MCB DB's with copper busbar complete all as specified and directed.

S&F in repair DB, SPN 4 ways, single door type complete all as specified and as directed.

S&F in repair 240V, 10 KA 'B' curve MCB SP of current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

S&F 415V, 10KA 'C' curve MCB TPN of current carrying capacity in the MCB DB complete with connection testing and commissioning of capacity 40 to 63 Amps complete all as specified and directed.

SRI GANESH ENTERPRISES (BID ID -3074358)

chowdeshwariconstructionco (BID ID -3073696)

M/S J S PRAKASAM (BID ID -3087174)

S SELVALAKSHMI ENGINEER AND CONTRACTOR (BID ID -3073319)