SPL REP TO CC 31 A AND PROVN OF 08 TOILETS AT CAMP AREA UNDER GE(AWC) MHOW.

Amount

Excavation in over area, not exceeding 1.5 M wide and not exceeding 1.5 m depth for foundation, etc., and getting out in hard/dense soil, complete all as specified and as directed.

Excavation in trenches, exceeding 1.5 M wide and not exceeding 3.0 M depth for foundation, etc., and getting out in hard/dense soil, complete all as specified and as directed.

Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out hard/dense soil, complete all as specified and as directed.

Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point, complete all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soils, complete all as specified and as directed.

M&L Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete, complete all as specified and as directed.

M&L cement concrete type D2 1:4:8 ( 40 mm graded aggregate) 75 mm thick, complete all as specified and as directed.

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface all as specified and as directed.

M&L Treating the soil under plinth protection at the rate 5 litres of emulsion per square metre of surface area all as specified and as directed.

Use & Waste of flat Form work to sides of concrete flat foundations rafts etc, complete all as specified and as directed.

Use & Waste of for flat Square, rectangular or polygonal Form work to sides of pillars, posts, struts, columns and stanchions, complete all as specified and as directed.

Use & Waste of Form work to sides and soffits of floor/plinth or roof beams, lintels, cantilevers, shelves including supports etc, complete all as specified and as directed.

M&L for RCC design mix M-25 as in foundation, footing, plinth beam etc, complete all as specified and as directed.

M&L for RCC Design Mix M-25 as in colums, posts and struts, complete all as specified and as directed.

M&L for RCC Design Mix M-25 as in slabs supported on walls etc, complete all as specified and as directed.

M&L Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as specified and as directed.

Description same as per Item No. 16.00 but 5mm dia and over upto and including 10mm dia in stirrups, spacers,distribution and binders, complete all as specified and as directed.

S&F Joist, channel, angle or tee , square or rectangular sections, beam , etc fixed indipendently including cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting plates with bolts and nuts , providing and fitting angle cleats, fish plates, gusset plates etc, complete all as specified and directed. Note :- Fabrication like cutting , welding, bending , or any other nature of work shall be at site or shop including in above rate.

S&F Mild steel bolts.purpose made.with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut, complete all as specified and as directed.

S&F Plates (plain or chequered) channels , square or beams cut or notched (ordinary and counter sunk) forming holes, without any attachments or with rivited, bolted ot welded attachments, etc confirming to Fe 410-W(Gde-E-250)quality-A complete all as specified and directed. Note - The rates quoted shall deemed to be include cutting to require size and welding or boulting to Beam , post, rafter shall be extended at site, rate included in this item.

M&L Plastering 15 mm thick in two layers of 10 mm thick in bottom and 5 mm thick in CM 1:4 mixed with WPC on top layer on Fair Faces of Brick Wall, Cement block wall or on Concrete Surfaces, Surface Finished Even and Smooth without using Extra Cement complete all as specified and as directed. Note:- WPC will be measured and paid separately.

Supply only Integral water proofing compound, complete all as specified and as directed.

M&L Moorum / Red Bajari filling in floor or pavings, laid in layers n. exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for Hard core, broken stone / boulders to gauge n exc 63 mm complete all as specified and as directed.

M&L 75 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) in Plinth protection including finishing the surface even and smooth without using extra cement, complete all as specified and as directed.

M&L non-skid / mat finish coloured joint free ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:4 complete all as specified and directed.

M&L glazed ceramic coloured tiles size 300mm x 450 mm x 6-7 mm thick (Colour and design of tiles as approved by GE) on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and and including 10 mm thick plaster in cement mortar 1:4 complete all as specified and directed.

S&F powder coated aluminium ventilator cross section conforming to IS 63.5x38.10x1.5mm consisting of two partitions upper portion shall have louvers with 3mm thick pin headed glass and aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56m fixed with aluminium beads and securing on outer face of frame and lower portion of ventilation shall be fixed with 3mm thick pin headed glass with IDPE rubber gasket including aluminium beads, including preparation of jombs all around in CM 1:3 finishing even and smooth complete all as specified and directed.

M&L providing factory made 100% solid WPC (wood polymer composite) door frame 90 mm X 45 mm (straight) single rebated, made form wood polymer composite) Single extruded process) material compressing of virgin PVC polymer of K value 57-60 (suspension grade). calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nor toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treaded star headed screws having minimum frame density of 780 kg/ cbm. Manufactured by ISO 9001-2015 certified company , having good screw holding capacity (screw withdrawal strength of (Min 990 N) minimum compressive strength of 58 N/mm square, modulus elasticity 900N/mm square and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof & fire retardant & fixed in position with SS dash fasteners / hold fast of required dia the and lenght, all as directed by the engineer-in-charge. material test certificate and authentication should be compulsory provided by the manufacturing company (hold fast or dash fasteners shall be paid separately).

M&L providing factory made 24 mm Thick 100% solid WPC (Wood Polymer Composite) Plain/ laminated flush door shutter of required size comprising of virgin PVC resin of K value 57-60 (suspension Grade) calcium carbonate and natural fibers (wood powders/ rice husk/ wheat husk) and non toxic additives made from extrusion process WPC foam sheet single extruded (inner) with density not less than 650 kg/cbm. Manufacturred by An ISO 9001-2015 certified company having good screw holding capacity (screw withdrawal strenght of 2000N (Face) & 1100 N (Edge), minimum compressive strength of 50N/mm square, modulus of elasticity 850N/mm and resistance of spread of flame of class A category with property of being termite/ borer free. water / moisture proof and fire retardant and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws. all as per direction of engineer-in-charge, material test certificate and aughentication should be compulsory provided by the manufacturing company for WC/ bathroom/ toilet/ kitchen/ balcony doors.

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, 100 mm length of bolt, ISI marked complete all as specified.

S&F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and as directed.

S&F 150 mm size aluminium handles cast type, anodised ISI marked , complete all as specified and as directed.

S&F 250 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed, complete all as specified and as directed.

S&F 1000 Ltrs capacity rotational moulded polyethylene water storage tanks, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I , complete all as specified and as directed.

S&F ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (Minimum weight 210 gms), complete all as specified and as directed.

Supplying and laying of 16 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches, complete all as specified and as directed.

Supplying and laying of 20 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified.

S&F PVC connection 15 mm dia 600 mm long with PTMT nuts at both ends complete all as specified and directed.

S&F over head shower with arm & flnge of chromium plated with or without swivel joints, any size, including fixing to 15mm dia steel pipe for required length or union complete all as specified and directed

S&F vitreous china wash basin flat back of size Min size 550x400mm counter top incl brackets, cutting for and pinning in ends or brackets, 32 mm dia waste coupling, botal trap and down pipe also,etc, complete all as specified and directed.

Supply only pillar tap Suitable forItem No. 41.00, single lever mixer complete all as specified and directed.

S&F vitreous china squatting pan “ORISSA PATERN” of size 580 mm X 440 mm, white, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc complete all as specified and directed.

S&F 15 mm Stop cock / angle cock chromium plated with high pressure crutch or butterfly handle screwed with both ends for iron pipe or PVC connection complete all as specified and directed.

S&F 15 mm Bib tap fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F Gun-metal, globe of gate balve /flush cock of 20mm bore with iron wheel head, screwed both ends for iron pipe etc all as specified.

S&F brass chromium plated towel rail 20 mm outer dia Bracket type, 60 cm long between flanges with and including chromium plated brass screws and wooden / plastic cleats, complete all as specified and as directed.

M&L providing pre-cast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab of manholes, septic tank, soak well etc set in cement mortar 1:4 with plain fair faces including chamfered weathering, throating etc including necessary use and waste of form work , complete all as specified and as directed.

M&L preparation of new painted Brick, stone, concrete, AC or plastered surfaces of of walls any description over 10 cm width or girth , not otherwise described and applying one coat of primer and two coats of exterior emulsion paint (Apex or Weather coat) white or tinted inluding external wall putty, complete all as specified and as directed.

M&L cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate for the 150 mm internal dia of pipe complete all as specified and directed.

Supplying, laying, jointing and testing reinforcedbconcrete pipes, class NP 2 laid in trenches and jointed cement mortar 1:1 complete all as specified and directed.

S&F PVC (SWR) Floor trap/Nahani trap plain or multi with stainless steel grating incl joining to waste pipe with solvent cement joint dia of outlet 75 mm bore complete all as specified and directed.

S&F 110 mm dia bore. PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor/ trenches complete all as specified and directed.

S&F 110 mm dia bore. PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls complete all as specified and directed.

S&F 110 mm dia bore PVC (SWR) junction single, single (T) equal or unequal with solvent rubber ring joints, fixed complete all as specified and directed.

S&F 110 mm dia bore PVC (SWR) vent cowl rubber ring joints, fixed complete all as specified and directed.

S&F 110 mm dia bore PVC (SWR) bends any radius with solvent rubber ring joints, fixed complete all as specified and directed.

S&F 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor/ trenches complete all as specified and directed.

S&F 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F 75mm dia bore PVC (SWR) bends any radius with solvent rubber ring joints, fixed complete all as specified and directed.

S&F 75mm dia bore PVC (SWR) junction single, single (T) equal or unequal with solvent rubber ring joints, fixed complete all as specified and directed.

S&Fmild steel chromium plated grating (round)125mm dia fixed over floor/Nahani trap complete all as specified.

S&F in repairs powder coated steel peg set having 06 Nos spikes fixed to wall complete all as specified and directed (Make as spproved by GE)

S &F Deck sheet area mezzanine (TR 60) 0.9 mm all asper specified and directed by Engn-in-charge.

S &F 90 mm EPS panel including all locking arrangement, gap filling with polymer mortar, fiber taping in all respect as directed by manufacturer specification. Note:- (i) This item is factory made pre-fabricated sandwich panel system made out of cement or calcium silicate boards and cement mortar with EPS (Expanded Polysterene)granules balls and act as wall panel. (ii) For familirisation of this material, bidders are requested to visit Light House Project at Indore MP at following address Kanadia Ext Sonyogitegani Mendal Indore MP. (iii) Fiber taping for joints and filling with polymer / epoxy based mortar in joints to be carried out on both sides of the joints, and quoted rate includes this provision. (iv) The quoted rate includes all minor details / requirements while executing this item. Make:- Rising Japan Infra Mumbai LLP or other equivalent make as approved by GE.

M& L Seamless calcium silicate ceiling 12mm made out of 1800 x 1200 mm size board of siliceous and calcareous materialreinforced with cellulose fibre fixed tothe ceiling section with 25 mm longself drilling and tapping screws having phillips head with under headcutter at 200 mm centre to centre,including finshing the joint of faceboard with specially formulatedjointing compound and 48 mm widefibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately), complete all as specified and as directed.

M&L Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, complete all as specified and as directed.

M&L Preparation of new painted Brick, stone, concrete, AC or plastered surfaces of of walls any description over 10 cm width or girth , not otherwise described and applying one coat of primer and two coats of plastic emulsion paint complete all as specified and directed including 3 mm thick putty, complete all as specified and as directed.

M&L preparation of new steel surface and apply one coate of red oxide and two coats of synthetic enamel paint complete all as per specified and directed.

M&L for 100 mm thick PCC in concrete type C- 2, 1:2:4 (using 40mm graded aggregate) as in sub base floor, complete all as per specified and directed.

M&L 60mm thick Machine pressed precast concrete interlocking paver block (Glossy Finish) of M-35 grade any shape and size confirming to IS 15658-2006, laid, jointing and pointed in neat cement slurry over & including dry sand cushioning 40 mm thick, complete all as per specified and directed. Note:- Sand cushioning included in this item.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Demolition of Stone slabs and tiles(granite/kotastone) of any description or thickness laid bedded or pointed any mortor in floors,kitchen slabs,shelves aprons etc. complete.

Demolition of Concrete (Unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L 75mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) used as sub base under floor finishes laying (kota/Marble/tiles etc) complete all as specified and directed.

M&L 20mm thick Screed bed or bedding layer of cement mortar 1:4 thick for laying floor finishes (Kota/Marble/Granite/ etc) complete all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. Note:- Screed bed shall be measured and paid separately.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Pre- painted galvalume aluminum zinc coating GI based corrugated steelsheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding towall, fixed with self tapping screws as specified

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and as directed.

M&L Rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces of wall complete all as specified and directed.

M&L Rendering 10mm thick in CM 1:6on fair faces of brick work or concrete surfaces of ceiling complete all as specified and directed.

M&L for preparation of New surfaces of wall and applying two coat of white wash complete all as specified and directed.

M&L for preparation of New surfaces of ceiling and applying two coat of white wash complete all as specified and directed.

M&L 20-25mm thick Granite (of any type) work (table rubbed and polished) laid over 20mm thick bedding in CM 1:4 in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in C:M 1:4 Complete all as specified and directed.

M&L Plain fillets. Square rectangular or triangular in section exc 13 n exc. 25SqCm, clean sawn, secured with nails or brads.M&L,fixed with screw complete all as specified and directed.

Dismantling boarding, any description, fixed in any position h fixed with screws, complete all as specified and as directed.

M&L 12mm thick Veneered decorative ply wood, grade I (with BWR resin) decorative veneers on both faces for kitchen cupboard complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 30 mm for kitchen cupboard complete all as specified and directed.

S&F 125mm long Aluminium handles, cast type, anodised complete all as specified and directed.

M&L100 mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) used as plinth protection complete all as specified and directed.

Taking down Chowkhats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames complete all as specified and directed.

M&L Anodised aluminium window and ventilator shutters, side hung type without sash bars, Aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified

Taking up or down 15 mm steel tubing and connections, including removal complete all as specified

Taking up or down 20 mm steel tubing and connections, including removal complete all as specified

S&F 15mm bore steel Tubes, medium grade galvanised, with all fitting;laid in wall complete all as specified and directed.

S&F 20mm bore steel Tubes, medium grade galvanised, with all fitting;laid in wall complete all as specified and directed.

S&F Galvanised steel wire cloth. 0.63 mm nominal dia of wire and average width of aperture 1.40mm for window and door complete all as specified and directed.

Complete removal of existing treatment and applying two coat of cement base paint on old surface of wall complete all as specified and directed.

Taking down carefully copper/aluminium point wiring of lights,fan,bell ,sockets and power point complete all as specified and as directed.

Point wiring with 1.5 Sqmm (nominal cross sectional area ), single core, PVC insulated with multistranded PVC unsheathed FR LSH copper conductor cable in and including rigid non- metallic PVC concealed conduit of suitable size medium grade ISI marked complete , including one continuity earth wire of PVC insulated, unsheathed 1.5 Sqmm (nominal cross sectional area ) FRLSH copper conductor connected to all fittings, common earth and connected to earth dolly including including modular metal flush box , cover plate and cover frame of suitable size incl taking down carefully copper/alluminium point wiring light, fan, sockets , all fittings and accessories and making good disturbed surface of walls and floors etc. complete all as specified and directed forOne light / fan /bell controlled by one, one way switch 5/6 Amps.

Description same as per Item No. 104.00 here in above but for One 3 pin, 5/6 amps socket outlet point on independent board controlled by one, one way 5/6 amps switch

Description same as per Item No. 104.00 here in above but One 3 pin, 5/6 amps socket outlet point on same board controlled by one, one way 5/6 amps switch

Point wiring with 2.5 Sqmm (nominal cross sectional area ), single core, PVC insulated with multistranded PVC unsheathed FR LSH copper conductor cable in and including rigid non- metallic PVC concealed conduit of suitable size medium grade ISI marked complete including one continuity earth wire of PVC insulated, unsheathed 1.5 Sqmm (nominal cross sectional area ) FR LSH copper conductor connected to all fittings, common earth and connected to earth dolly for one three pin 15/16 amps socket out-let point on an independent board including modular metal flush box , cover plate and cover frame of suitable size incl taking down carefully copper/alluminium power point wiring switches , sockets , and making good disturbed surface of walls and floors etc. complete all as specified and directed.

S&F Ceiling rose three terminals surface bakelite type, ISI AC, 50 HZ, 230V complete all as specified and directed.

S&F modular switch 1 way 6 A , 1 module, ISI complete all as specified and directed.

S&F modular socket 6 Amps 2/3 pin combined 2 module, ISI complete all as specified and directed.

S&F switch modular type 16 A, 1 module, ISI complete all as specified and directed.

S&F socket modular type multipurposes 6/16 A, 2 module, ISI complete all as specified and directed.

Supply and fixing surface /wall mounted LED batten (other than slim channel) poly carbonate housing for retrofit LED tube T-8 type upto 1x22 watt, 4 feet long pre wired incl integrated electronic driver complete with all connected accessories all as specified and directed.

Supply and fixing ultrabright LED polycarbonate tube liight 4 ft long 20 watts with THD <= 15% very high efficiency suited for T-8 tube light luminaire with system efficacy >= 120 Lm/W. High quality polycarbonate end cap in white finish and snap fitted to the housing complete all as specified and directed.

Supply and fixing wall mounted LED tube light fitting 10 watts comprising batten of extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver 10 W LED 2 feet long ,THD less than 15% complete all as specified and directed.

M&L for LED Bulk head fitings 6 - 13 watts designed for modern homes available with premium quality diffuser for glarefree light and easy to install snapfit installer complete including taking down of old CFL/bulb bulk head fitting, making good of surfaces all as specified and directed.

S & F LED bldg security light fitting 30 watt lumen output >= 100lm/W made up of pressure die cast aluminium housing with acylic cover as diffuser with IP-66 protection complete incl GI pipe 1.2 mtr length bend into size fixed on wall with saddles and screws all as specified and directed.

S&F MCCB ,DB VTPN wall mounted double door 6 way IP43, IK 09, 415 volts with facility to provide MCCB 3 pole 125 Amps 25 KA as incomer and SP/TP MCB's/Isolator as outgoing including removed old U/S DB in the wall again fixing the new DB and wall finising complete all as specified and as directed.

S&F MCB DB SPN 12 way IP43, IK 09, double door with 200 Amps rated bus bar ,230 volts, 50 Hz complete all as specifed and directed.

S&F MCB DB SPN 8 way IP43, IK 09, double door with 200 Amps rated bus bar ,230 volts, 50 Hz complete all as specifed and directed.

S&F MCCB 3 pole 415 V 125 A, 50 Hz with rupturing capacity 25KA, Ics=100% Icu complete all as specified and directed.

Supply & Fix MCB SPN 40 Amps current rating 'C' series 10 KA breaking capacitycomplete all as specified and directed.

Supply & Fix MCB TP 40 Amps current rating 'C' series 16 KA breaking capacitycomplete all as specified and directed.

Supply & Fix MCB SP 6 to 32 Amps current rating 'C' series 10 KA breaking capacity complete all as specified and directed.

Sub main wiring with 2 single core,6 Sqmm, PVC insulated PVC unsheathed stranded FR LSH copper conductor cable in and including PVC concealed/ surface conduit of earth wire with 1 x 6.0 Sq mm copper cable fixed along with the sub main in PVC conduit and connecting to earth dolly complete including taking down old sub main wiring, complete all as specified and directed. Note:- 3 runs of copper conductor + 1 run of pvc conduit shall be measured 1 RM

Sub main wiring with 2 single core,4 Sqmm, PVC insulated PVC unsheathed stranded FR LSH copper conductor cable in and including PVC concealed/ surface conduit of earth wire with 1 x 4.0 Sq mm copper cable fixed along with the sub main in PVC conduit and connecting to earth dolly complete including taking down old sub main wiring all as specified and directed. Note:- 3 runs of copper conductor + 1 run of pvc conduit shall be measured 1 RM

Taking down existing exhaust fan/ceiling fan of any sweep after disconnecting necessary connection from ceiling rose to fan and deposit to MES store yard complete all as specified and as directed

S&F in replacement of exhaust fan non metalic single phase 230 volt of size 250 mm sweep with louver all as specified and as directed

S&F Exhaust fan non metalic single phase 230 volt of size 250 mm sweep with louver all as specified and as directed.

M&L for painting of ceiling fan 1200 mm sweep complete with synthetic enamel paint by spraying , filling cavities with filler, one coat after cleaning all dust incl hanging into its original position, changing of conopies,connection wires all as directed.

S&F Exhaust fan , steel body AC single phase 230 volt of size 300 mm sweep complete with blade, frame and louvers all as specified and directed incl making/alteration of hole wherever necessary making good disturbed surface, painting to match with existing surfaces.

S & F for energy efficient exhaust fan of 450 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making altration and well finishing to to existing brick wall for fan base compelte all as specified and directed.

Supply and fix Sheet metal enclosure, SPN, with two pin and earth metal plug and socket, 20 Amps, 240 Volts, including one MCB SP 20 Amps complete all as specified and as directed.

Supply and fix Sheet metal enclosure, TPN, with two pin and earth metal plug and socket, 20 Amps, 240 Volts, including one MCB TP 40 Amps C series complete all as specified and as directed.

Supply , fixing rigid non metallic PVC conduit fixed conceiled/on wall wherever necessary with all connected accessories 20 mm dia incl pulling of existing electric cable inside conduit complete all as specified and as directed

S&F fan regulator stepped electronic, modular type 02 module ISI as specifed and directed.

M&L for removal of Geyser any capacity and refixing the same after plastering and painting work, connecting cable to metal flush box with suitable metallic plug top , cleaning the geser , removing dust particle incl making good of disturbed sufrace complete all as specified and directed.

S&F water heater storage type of 5 Star rating, capacity 25 liters with , glass coated heating element to protect the heating element from oxidation and carbonization. The geyser should be tough enough to withstand pressure upto 8 bars . The inner tank should have a minimum 7 years warranty . The geyser should have company fitted and warrented ELCB or shock safe plug including PTMT connections 15 mm size with nuts and length of 450 mm with all accessories such as safety valve, thermostate incl fixing arrangements. complete all as specified and as directed. Note:- Additional warrenty on models having warrenty less than 07 years will not be accepted.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sq. mm 2 core in trenches / under PCC/interlocking tiles incl making good of surface with PCC/ cementing all as as directed at site

M&L for replacing PCC cable cover class LV , flat size 250x150x40 mm size complete all as specified and directed

M&L of locally available river sand in trenches below and above / around UG cable for cable protection, in duct under & above the cables including punning around cable complete all as specified and directed. Note - Punned thickness shall only be measured and paid.

Replacement of Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in ground vertically to a depth not less than 2.25 meters deep below ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level connect to galvanised earth lead wire of 4.0 sqmm size by means of bolts, nuts, check nuts and washers of galvanized iron or steel up to 7.5 meter length including connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber, 40 mm thick RCC cover 1:2:4 mix with 6mm dia nominal reinforcement @ 150 mm c/c both ways etc complete all as shown in electrical plate No 3, connected to earthing test point complete including testing on completion all as specified.

M/S Ashish Construction

ram prashad chotelal batham

M/S GARG CONSTRUCTION

M/s Hansraj Shivhare