REPAIRS TO FENCING, DRAIN, CULVERTS, FOOTPATH,BOUNDARY WALL, GATES AND OTHER MISCELLANEOUS WORKS IN DOMESTIC AREA AT AFA HYDERABAD

Amount

Dismantling existing barbed wire/plain wire/ chain link fencing any type from RCC/Steel/Wdn posts complete etc all as specified and as directed.

Dismantling existing fencing posts (RCC / wooden post) of any description including embedded portion inside the ground, incl. getting out and removing soil to a distance not exceeding 50 m complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L Cement concrete (1:3:6) type C2 (using 40 mm graded stone aggregate) in foundation, post holes, filling and mass-concrete complete all as specified and directed

M&L for precast cement concrete 1:2:4, type B1 (using 20 mm graded stone aggregate), as in RCC fencing post or in simillar works etc with plain fair faces including necessary form work and set in CM 1:6, complete all as specified and as directed.

M&L for MS TMT bars 6 to 8 mm dia cut to length bent to shape required including cranking, bending, spirally for hooping for columns, cover slabs, in pre cast works, etc, by hooking ends and binding with MS wire (annealed) not less than 0.90 mm dia complete all as specified and as directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia etc all as specified and as directed.

S & F of MS flat as used in tie bar, wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and directed

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 15cm and n exc 22.5cm long, dia of shank 11 to15mm, all as specified and as directed.

S&F of MS galvanised chain link fencing of size 50mm x 50mm x 3.80mm fixed to any type of fencing posts with straining bolts, stiffener rods etc. including provision of binding wire if required etc complete all as specified and as directed by Engineer-in-charge.

M&L for mild steel round bars 10 and over dia as required, made to shape for securing chain link fencing etc., and similar works conforming to Fe-290 Gde E-165 and including preparation and applying two coats of synthetic enamel paint over a coat of red oxide primer before fixing etc complete all as specified and as directed

S & F Mild steel work in framed grills and hung gates, including Pintle hinges, stops, hand made sliding bolts etc. and similar work confirming to Fe 290 Gde E-165, etc complete all as specified and as directed.

M&L for preparation and applying two coats of synthetic enamel paint over a coat of red oxide primer on newly treated steel surfaces of any description, exc 10 cm width or girth etc complete all as specified and as directed. .

M&L in repair Concertina coil super barb - bladed profile of dia 610 mm of weight not less than 8.50 kgs per coil of 7.5m of length fixed to angle iron brackets or masonry surfaces with necessary accessories like straining wires, fixing clips etc complete all as specified and as directed. Note :- Concertina coil shall be measured linearly of fencing length. The number of spirals shall not be less than 51 in 7.5 m length of each coil.

Removing and refixing existing old concertina coil of 600mm dia weighing approx 8.5kg/7.5m or stacking already fallen concertina coil and refixing the same at position including stacking properly, restraining etc complete all as specified and directed

S&F in repairs, Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

Removing and Restraining, resecuring, Refixing of old existing Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings or untangle fallen old barbed wire and straining and refixing to any type of standard rails straining bolts, including making good , securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed Note:- Each line wire to be measured

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for etc and removal of debris off the premises complete all as specified and as directed. (Reinforcement cut as required to facilitate demolition)

Excavation in trenches not exc. 1.5 mtr wide and not exc. 1.5 mtr in depth and getting out in soft/loose soil for foundation, trenches etc. all as specified and as directed.

Demolition of brick work or stone/boulders, pcc block masonry built in Cement Mortar or cement lime mortar including all quoins, arches, pillars etc excluding ashlar facings, dressed stone work and precast concrete articles and removing the unserviceable debris off the premises complete all as directed.

Demolition of cement concrete (unreinforced) of any description and in ground floors and pavings n exc 15 cm thickness (below or above ground level) any position and disposed off to a distance exc. 50 mtrs and not exc. 250 mtrs all as directed by Engr-in-Charge.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc. and removing the rubbish off the premises complete all as directed.

M & L for Plain Cement Concrete (1:4:8) Type D2 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete all as directed.

M & L for Pre-cast cement concrete block masonry with solid blocks, Type C1 1:3:6 (20mm graded stone aggregate) exc. 10 cm in width and setting in cement mortar 1:6, complete all as directed.

M&L for Brickwork (Except bricks) with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as directed. Note: (Serviceable bricks obtained from dismantling item No.20 shall be made use of).

M&L for walling of random rubble masonry uncoursed, well bonded, bedded and solidly hearted in cement mortar 1:6 complete all as specified and as directed.

M&L for forming fair finished drain or channel 30 to 60cm inner girth in cement concrete, using extra cement , including forms, moulds, mitred/stopped ends etc all as specified and as directed.

M&L for PCC 1:2:4 (type B) (using 20 mm graded stone aggregate) as in copings, benching, Kerb, cills, bands, bed plates etc including weathering, slightly rounded or chamfered angles and throating etc all as directed by Engr-in-Charge

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement all as directed by Engr-in-Charge.

M&L for Rendering 15 mm thick on fair faces of stone masonry surfaces in CM 1:6 finished even and smooth without using extra cement all as directed by Engr-in-Charge.

M&L for preparing new plastered wall surfaces and applying Two coats of white wash all as directed by Engr-in-Charge.

M&L for precast cement concrete 1:2:4, type B1 (using 20 mm graded stone aggregate), as in cover slabs, shelves or in simillar works etc including necessary form work and set in CM 1:6, complete all as specified and as directed.

S&F Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, etc complete all as specified and as directed.

Returning , filling in including spreading, levelling , watering and well ramming in layers not exc 25cm in soft/loose soil etc all as specified and as directed.

Removing excavated soil to a distance n exc 50m and depositing where directed at a level n exc 1.5m above the starting point etc all as specified and as directed.

M&L for PCC (1:4:8) type D2 (Using 40 mm graded stone aggregates) for sub base of floor, 75 mm thick all as directed.

M&L Colour Chequred cement concrete tiles 30 cm x 30 cm x 25 mm thick with grey cement and pigment set jointed and pointed in neat cement slurry to match, in floors, laid over and including screed bed in CM (1:6), 15 mm thcik complete all as specified and as directed.

M&L machine pressed precast concrete ( with grey cement and pigment ) interlocking paver block any shape and size conforming to IS-15658- 2006 of 60 mm thickness M-40 grade laid over and including 25 mm thick (Avge) sand filling including watering and consolidation complete all as directed.

M/L PCC 1:2:4, type B2 (Using 40 mm graded stone aggregates) for 100 mm thick path/ flooring, finished even and smooth without using extra cement all as directed.

M&L PCC 1:3:6, type C-2 (using 40 mm graded stone aggregates ) for plinth protection 75 mm thick, finished even and smooth without using extra cement all as directed.

M&L for Forming construction (dummy) joints 65 mmx10 mm wide filled with sealing compound grade A. all as specified and directed.

Demolition and breaking up drain pipes of 300mm dia(Salt glazed ware, AC or Reinforced concrete) set in cement mortar and removing debris off the premises all as specified and directed

M&L for Reinforced concrete pipes of dia 300 mm, class NP2, laid and jointed complete with collars all as specified and directed

M&L for Cement concrete (1:4:8) type D-2 (Using 40 mm graded stone aggregates) Concrete bed to drain pipes of bore dia 300mm including packing under and completely surrounding pipes with concrete after they are laid and tested; complete all as specified and as directed.

Raking out joints to random rubble uncoursed or brought up to courses built in cement mortar complete all as specified and as directed.

M & L for flush pointing to random rubble masonry uncoursed or brought up to courses in cement mortar 1:4 complete all as specified and as directed.

Deepika Enterprises

M.chandraiahsons

Sneha Associates

S J REDDY