Loading…
Loading…
Tender Value
₹3.2 Cr
EMD Value
₹6.4 L
Closing Date
2 Jul 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
DEN 2
15 conditions · 3 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover.
The tenderer shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
75 conditions · 21 needing a document upload
" No post tender correspondence will be done with the participant tenderer(s) for deficient credentials noted during scrutiny of tender/offer nor any credential will be accepted after opening of the tender and the offer shall be decided on the basis of submitted/Credentials downloaded with offer only"
If it is NOT mentioned in the submitted tender that tender is being submitted on behalf of a Sole Proprietorship firm / Partnership firm / Joint Venture / Registered Company etc., then the tender shall be treated as having been submitted by the individual who has signed the tender.
After opening of the tender, any document pertaining to the constitution of Sole Proprietorship Firm / Partnership Firm / Registered Company/ Registered Trust / Registered Society/HUF etc. shall be neither asked nor considered, if submitted.Further, no suo moto cognizance of any document available in public domain (i.e., on internet etc.) or in Railway's record/office files etc. will be taken for consideration of the tender, if no such mention is available in tender offer submitted
No post tender correspondence will be done with the participant tender(s) for deficient credentials noted during scrutiny of tender/offer nor any credential will be accepted after opening of the tender and the offer shall be decided on the basis of submitted/Credentials downloaded with offer only.
Tenderers attention is invited to clause I of Section VII and other relevant clauses of Section I and II whereby in case of non- submission/non compliance, the tender offer is likely to be rejected.
The tenderer/s shall submit a duly filled Tender form TENDER FORM (First Sheet) as per "ANNEXURE-I" OF STANDARD TENDER DOCUMENT"
BID Security (Bank Guarantee Bond from)-Annexure-XXII, The original Bank Guarantee should be delivered in person to the official nominated as indicated in the tender document before closing date for submission of bids (i.e.excluding the last date of submission of bids)
The tenderers shall submit a copy of certificate stating that all their statements/documents submitted a longwith bid are true and factual. Standard format of certificate to be submitted by the bidder is enclosed as Annexure-V. In addition to Annexure-V, in case of other than Company/Proprietary firm, Annexure-V (A) shall also be submitted by the each member of a Partnership Firm/ Joint Venture (JV)/Hindu Undivided Family (HUF)/ Limited Liability Partnership (LLP) etc. as the case may be. Non submission of above Certificate(s) by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested/digitally signed by which they/he is qualifying the Qualifying Criteria mentioned in the Tender Document.
The following documents should be specified for submission along with tender:
A. List of Personnel, Organization available on hand and proposed to be engaged for the subject work.
B. List of plant Machinery available on hand own and proposed to be inducted own hired to be given separately for the subject work.
C. The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work each costing not less than the amount equal to 60% of advertised value of the tender. Description of work, organization for whom executed, approximate value of contract at the time of award, date of award and date of scheduled completion of work, Date of actual start, actual completion and final value of contract should also be given.
D. List of works on hand indicating description of work, contract value, and approximate value of balance work yet to be done and date of award.
The tenderers whether sole proprietor , a limited company or a partnership firm he/they should submit authentic proof in terms of partnership deed, proprietorship documents etc. along with the tender. If he/they want to act through agent or individual partners should submit a power of attorney duly stamped and authenticated by Notary Public or by Magistrate in favour of specific person whether he/she/they are partners of the firm or any other person specifically authorizing him/her name to submit the tender, sign the agreement , receive money, witness measurements, sign measurement books , compromise, settie, relinquish any claims, preferred by firm and also sign No Claim Certificate and refer all or any disputes arbitration.
Bid Security: (a)Subject to exemptions provided under para 4(iv)) of this document, the tender must be accompanied by a Bid Security as mentioned in tender documents, failing which the tender shall be summarily rejected. (b)The Tenderer(s) shall keep the offer open for a minimum period of 60 days (in case of two packet system of tendering 90days) from the date of closing of the Tender. It is understood that the tender documents have been issued to the Tenderer(s) and the Tenderer(s), is / are permitted to tender in consideration of the stipulation on his / their part that after submitting his / Their tender subject to the period being extended further, if required by mutual agreement from time to time, he will not resile from his offer or modify the terms and conditions thereof in a manner not acceptable to North East Frontier Railway. Should the tenderer fail to observe or comply with the foregoing stipulation, the amount deposited or Bank guarantee bond submitted as Bid Security for the due performance of the above stipulation, shall be forfeited to the Railway. (c)If his tender is accepted, (i)the Bid Security mentioned in sub para(a) above deposited in cash through e- payment gateway will be retained as part security for the due and faithful fulfillment of the contract in terms of Clause 16 of the Standard General Conditions of Contract; (ii)the Bid Security mentioned in sub para(a) above submitted as Bank guarantee bond, will be encashed as part security for the due and faithful fulfillment of the contract in terms of Clause 16 of the Standard General Conditions of Contract. The Bid Security of other Tenderers shall, save as herein before provided, be returned to them, but the Railway shall not be responsible for any loss or depreciation to the Bid Security that may happen thereto while in their possession, nor be liable to pay interest thereon. (d)In case Contractor submits the Term Deposit Receipt/Bank Guarantee Bond towards either the Full Security Depositor the Part Security Deposit equal to or more than Bid Security, the Railway shall return the Bid Security so retained as per sub para(c) above, to the Contractor.
The following documents should be specified for submission along with tender:
A. List of Personnel, Organization available on hand and proposed to be engaged for the subject work.
B. List of plant Machinery available on hand own and proposed to be inducted own hired to be given separately for the subject work.
C. List of Works completed in the last three financial years giving description of work, organization for whom executed, approximate value of contract at the time of award, date of award and date of scheduled completion of work, Date of actual start, actual completion and final value of contract should also be given.
D. List of works on hand indicating description of work, contract value, and approximate value of balance work yet to be done and date of award.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Clause regarding GST - (a) Tenderer should furnished their GSTIN numbers representing the States in which they are registered for GST, along with address of Registered Office, place of business in State etc. (b) The contract is under GST act & rules as applicable time to time. (c) All the bidders/tenders should ensure that they are GST compliant and their quoted tax structure/rates are as per GST Law.
l) The tenderer(s) are required to submit the test report of the stone ballast conforming to railways specifications as given in the condition no.7.2.2 of section-VI along with their offer, issued from the approved laboratory as listed in condition no 7.1.1(a) of section-VI in the tender documents otherwise their offer shall be summarily rejected. (This item will be applicable only for the tenders of supply of ballast) (Mandatory).
The tenderers whether Sole Proprietor, a limited company or a partnership firm he/they should submit authentic proof in terms of partnership deed, proprietorship documents etc. along with the tender. If he/they want to act through agent or individual partners should submit a power of attorney duly stamped and authenticated by Notary Public or by Magistrate in favour of specific person whether he/she/they are partners of the firm or any other person specifically authorizing him/her name to submit the tender, sign the agreement, receive money, witness measurements, sign measurement books, compromise, settie, relinquish any claims, preferred by firm and also sign No Claim Certificate and refer all or any disputes arbitration.
(a) At the time of creation of any new tender in IREPS works module, an option has been provided to the tendering authority for obtaining Bid Security Declaration in lieu of Bid Security/Earnest Money Deposit. In case this option is selected, the Bid Security/Earnest Money Deposit amount for the tender shall be NIL. (b) If the tendering authority decides to take Bid Security/Earnest Money Deposit, it shall be mandatory for the tendering authority to provide reasons, and upload the approval of competent authority for the same. The Competent Authority shall be the next higher authority to the authority competent to finalise the particular tender. (c) In case Bid Security Declaration in lieu of Bid Security/Earnest Money Deposit is allowed against a tender, the provision has been made in IREPS for the bidder to mandatorily submit the following declaration along with his offer : If the bidder fails to submit the Bid security declaration, the bid will be rejected irrespective of winning the bid and qualifying for the tender.
Special repairs to leaky roof and other miscellaneous works in the Railway quarters under ADEN/BPG.
SCL-ENGG-43-2026
SCL-ENGG-43-2026
Open
Works - General
12 Months
Hojai, Assam
₹0
₹6.4 L
2 Jul 2026
8 Jun 2026
18 Jun 2026
125 items across 2 schedules · ₹97,65,815.9 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil. | cum | 40 | 260.3 | 10,412 |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. | cum | 110 | 196 | 21,560 |
| 3 | 1:1 1/2:3 (1 Cement: 1 1/2 coarse sand (zone- III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 5 | 8,340.85 | 41,704.25 |
| 4 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 15 | 7,878.5 | 1,18,177.5 |
| 5 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 10 | 7,178.75 | 71,787.5 |
| 6 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 20 | 9,045.75 | 1,80,915 |
| 7 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 15 | 10,852.95 | 1,62,794.25 |
| 8 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 100 | 392.15 | 39,215 |
| 9 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm | 30 | 736.4 | 22,092 |
| 10 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm | 30 | 961.3 | 28,839 |
| 11 | Thermo-Mechanically Treated bars of grade Fe- 500D or more. | Kg | 1350 | 107.85 | 1,45,597.5 |
| 12 | Cement mortar 1:4 (1 cement : 4 coarse sand) | cum | 5 | 7,370.65 | 36,853.25 |
| 13 | Cement mortar 1:4 (1 cement :4 coarse sand) | Sqm | 80 | 1,123.8 | 89,904 |
| 14 | Kiln seasoned and chemically treated hollock wood | cum | 10 | 83,378.05 | 8,33,780.5 |
| 15 | Kiln seasoned and chemically treated hollock wood | cum | 16 | 71,337.85 | 11,41,405.6 |
| 16 | 30 mm thick shutters | Sqm | 80 | 2,676.85 | 2,14,148 |
| 17 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 25 | 3,167.95 | 79,198.75 |
| 18 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 100 | 2,172.1 | 2,17,210 |
| 19 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). | Each | 250 | 228.85 | 57,212.5 |
| 20 | 250x16 mm | Each | 50 | 260.6 | 13,030 |
| 21 | 150x10 mm | Each | 150 | 82.55 | 12,382.5 |
| 22 | 100x10 mm | Each | 150 | 64.7 | 9,705 |
| 23 | 125 mm | Each | 100 | 66.25 | 6,625 |
| 24 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer- in-Charge. | Metre | 180 | 492.7 | 88,686 |
| 25 | 30 mm thick plain PVC door shutters | Sqm | 60 | 3,182.95 | 1,90,977 |
| 26 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 300 | 133.7 | 40,110 |
| 27 | 1:6 (1cement : 6 coarse sand) | Sqm | 50 | 965.55 | 48,277.5 |
| 28 | 40 mm thick with 20 mm nominal size stone aggregate | Sqm | 50 | 614.2 | 30,710 |
| 29 | 6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 : 2000 | Sqm | 1850 | 921.95 | 17,05,607.5 |
| 30 | 75 mm diameter | Metre | 30 | 248.8 | 7,464 |
| 31 | 110 mm diameter | Metre | 20 | 377.4 | 7,548 |
| 32 | 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) | Sqm | 100 | 1,355.8 | 1,35,580 |
| 33 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 3500 | 738.65 | 25,85,275 |
| 34 | Ridges plain (500 - 600mm) | Metre | 350 | 532.35 | 1,86,322.5 |
| 35 | 1:4 (1 cement: 4 fine sand) | Sqm | 650 | 347.05 | 2,25,582.5 |
| 36 | 1:4 (1 cement: 4 fine sand) | Sqm | 200 | 425.55 | 85,110 |
| 37 | New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre | Sqm | 1000 | 185.65 | 1,85,650 |
| 38 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture | Sqm | 500 | 176.25 | 88,125 |
| 39 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture | Sqm | 80 | 170.7 | 13,656 |
| 40 | Old work (one or more coats) | Sqm | 5000 | 62.7 | 3,13,500 |
| 41 | Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface | Sqm | 2750 | 120.75 | 3,32,062.5 |
| 42 | Providing and laying in situ seven course water proofing treatment with APP (Atactic poly- propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). | Sqm | 1500 | 730.55 | 10,95,825 |
| 43 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) | cum | 10 | 2,434.25 | 24,342.5 |
| 44 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | cum | 10 | 3,551.25 | 35,512.5 |
| 45 | In cement mortar | cum | 20 | 2,060.2 | 41,204 |
| 46 | Of area 3 sq. metres and below | Each | 140 | 367.2 | 51,408 |
| 47 | Of sectional area 40 square centimetres and above | cum | 16 | 4,459.1 | 71,345.6 |
| 48 | G.S. Sheet | Sqm | 3500 | 164.95 | 5,77,325 |
| 49 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. | Sqm | 1000 | 54.65 | 54,650 |
| 50 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | Each | 10 | 6,767.4 | 67,674 |
| 51 | 610x510 mm bowl depth 200 mm | Each | 10 | 4,940.8 | 49,408 |
| 52 | PN - 16 Pipe, 20mm OD (SDR-7.4) | Metre | 100 | 272 | 27,200 |
| 53 | PN - 16 Pipe, 25mm OD (SDR-7.4) | Metre | 100 | 318.35 | 31,835 |
| 54 | PN - 16 Pipe, 32mm OD (SDR-7.4) | Metre | 60 | 362.9 | 21,774 |
| 55 | 15 mm nominal bore | Each | 20 | 406.85 | 8,137 |
| 56 | 20 mm nominal bore | Each | 20 | 462.5 | 9,250 |
| 57 | 15 mm nominal bore | Each | 20 | 85 | 1,700 |
| 58 | 15 mm nominal bore | Each | 20 | 97.75 | 1,955 |
| 59 | 15 mm nominal bore | Each | 30 | 506.8 | 15,204 |
| 60 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | Kg | 50 | 495.05 | 24,752.5 |
| 61 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | Kg | 120 | 598.6 | 71,832 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TD-SCL-ENGG-42of2026.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .