PETTY REPAIR FOR ATTENDING DAY TO DAY EM EXTERNAL WATER SUPPLY COMPLAINTS IN COD DEPOT AREA 505 ABW FODDER LINE 1811 PNR COY 226 ASC SUPPLY ESD DEPOT I II FOL DEPOT AREA KIRBY PLACE ME LINE 17 SIKHLY OF UNDER AGE U WATER SUPPLY NO 1 UNDER GE U WA

Amount

Attending day to day external water supply compliants of all nature i.e. leakage in water supply pipe lines, fittings/fixture, over flow of overhead tank, no water supply compliants including ( excavation work due to no water supply ) from various areas as per compliant register etc complete all as specified and as directed.

Attending of Electric supply compliant of day to day maintenace of existing LT Panels including connecting electrical accessories / spares of water supply installation ,electrical fitting with lights , short circuits in Pump house as per compliant register complete all as specified and as directed. Note ;- Ser No . 1 & 2 Material required for attending complaints shall be measured & sparately under respectvie items here - in- after.

Note ;- Ser No . 1 & 2 The rates quoted by the contractor shall also deemed to be included for the following. :- (i) The complaints shall be attended and the defects shall be rectified by a team of matric qualified having minimum 03 years experienced electrician/Plumber as applicable assisted with adequate No of helpers as directed by Engineer-in-charge (ii) The complaints shall be attended & defect shall be rectified within 08 hrs commencing from date and time of notifying the complaint failing which a penalty @ Rs 50/- per complaint per day (08 hrs) shall be levied upon/imposed on the contractor and recovery shall be made from contractor's dues. (iii) In case , after checking & attending the defect, it is not possible to rectify the defect within 08 hrs, the facts shall be brought to the notice of Engineer-in-charge by the contractor/his rep. If Engineer-in- charge is satisfied with contractors view, no recovery will be made.

(iv) While attending the complaint of water supply if earth work is required then the same shall be measured and paid seperately under appropriate item of Sch 'A'. However , no extra payments shall be made for dewatering (v) Cutting of GI pipe in position and threading is also deemed to be included in the job rate (Fittings and fixtures will be measured and paid separetely under respective items of sch A. (vi) All T&P required for attending the complaints shall be provided by the contractor without any extra. (vii) The Pipe Fitter shall always be in possession of die set complete with cutters,Taps, Pipe wrench ,Chain wrench, Caulking tools, complete set of spanners and ladders etc ,as required at site (viii) The Electrician shall always in possession of all Electrician tools, LT Megger, Earth Tester, Multimeter , Crimpling tool, insulation tape, Hand gloves etc required at site. (ix) Rate for taking down/out existing & fittings & fixtures and refixing to make it functional shall be into account.

Supply only of the following items :-

Supply only GI socket Med grade ISI marked of following sizes :

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply only GI Elbow Med grade ISI marked of following sizes :

15 mm bore

20mm bore

25mm bore

40mm bore

50mm bore

Supply only GI Union Med grade ISI marked of following sizes :

15 mm bore

20mm bore

25mm bore

40mm bore

50mm bore

Supply only GI Nipple Med grade ISI marked of following sizes :

15 mm bore

20mm bore

25mm bore

40mm bore

50mm bore

Supply only GI Reducer socket Med grade ISI marked of following sizes :

20mm x15 mm bore

25mmx15mm bore

25mmx20mm bore

50mmx40 mm bore

Supply only GI Tee Med grade ISI marked of following sizes :

15mm x 15mm x 15 mm bore

20mm x 20mm x15 mm bore

20mm x 20mm x 20 mm bore

25mm x 25mm x 15 mm bore

25mm x 25mm x 20 mm bore

25mm x25mm x25 mm bore

40mm x40mmx15 mm bore

40mm x 40mm x 20 mm bore

40mmx40mmx25 mm bore

40mm x 40mm x 40 mm bore

50mm x 50mm x15 mm bore

50mm x 50mm x 20 mm bore

50mm x50mm x25 mm bore

50mm x 50 mm x 40 mm bore

50mm x 50mm x 50 mm bore

Supply only GI solid plug heavy duty ISI marked of following sizes :

15 mm bore

20mm bore

25mm bore

40mm bore

50mm bore

Fixing only PTMT Float valve with epoxy coated aluminium rod and high density plastic ball complete of following sizes : Note : PTMT Float valve shall be issued under Sch 'B as free for laying/fixing only.

15 mm bore

20mm bore

25mm bore

50mm bore

Fixing only Gun metal gate valve with iron wheel head screwed both ends for iron pipe as per IS-778 compete, ISI marked of following sizes : Note : Gun metal gate valve shall be issued under Sch 'B as free for laying/fixing only.

15 mm bore

20mm bore

25mm bore

40mm bore

50mm bore

Supply only following items :

Supply only Lead Pig bar

Supply only Spun yarn

Nuts, bolts and washers 25 to 150mm of 6 to 20mm dia

15mm bore Bib tap of PTMT, any tint, high pressure screwed for made/Female threaded for pipe of size 15mm bore

Laying & fixing in replacement of GI pipe mediun grade ISI mark including all fittings in old/new positions in trenches/wall/floor complet and making good the distributed surfaces as per existing complete all as specified and as directed of following sizes. Note : GI steel tubing shall be issued under Sch 'B as free for laying/fixing only.

15 mm bore

20mm bore

25mm bore

40mm bore

50mm bore

Excavation in trenches not exc 1.5 metres wide and not exc1.5 metres deep for pipe line in soft/loose soil, getting out and levelling of bottom surface to required level complete all as specified and as directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed.

Removing excavated material from site to a distance not exc 50 metres away and depositing where directed not exc 1.5 metres from the starting point complete all as specified and as directed.

Supplying and laying well burnt bricks sub class B for protection of cable for complete all as specified and as directed.

Supply and laying for sand cushioning to cable with a layer of sand 8 cm deep before laying and 15cms deep after the cable (punned down to 18cms depth after laying and stretching of cable) complete all as specified and as directed

Surface dressing of uneven surfaces of natural ground, rough excavated surfaces not exceeding 15 cm deep and filled area where ordered shall be trimmed to an even surface horizontal or stopping, by removing vegetation and by scrapping high patches and filling low patches with the scrapping soil to given an even and neat look to the site complete all as specified and as directed.

Testing of drinking water being collected from local source (bore wells/shallow wells/under ground sumps) in the area under AGE(U) W/S No I and submission of detailed test reqport to the office of Engineer-in-Charge. (i) Carrying out minimum essential testing of water as per IS 10500-1991 mandatory for chemical colour, odour, taste, tubidity, PH value TDS total hardness, iron, chloride, fluride and residual free chlorine and Bacteriological total Collie from organisms per 100 ml (MPN) and E Collie in 100 ml) and to this office with specific recommendation regarding suitability of water for drinking purpose. (ii) Collection of water from different sources of water ie Sump, bore wells & shallow wells in sterilized bottle and testing in Govt Approved laboratory as mentioned in specification. Note :- Rate quoted shall also deemed to be included for the followings : - (i) Cost of sterilized battle as required. (ii) To and for transportation charges for collection of samples from source(sump/bore well/shallow wells)

Supply only switch /sockets ISI marked of following items :

Switch piano flush type 5/6 Amps singal pole one way, 240 volts

Switch piano flush type 15/16 Amps singal pole one way, 240

Socket outlet 2 in 1, 3/5 pin, 5/6 Amps 240 volts

Socket outlet 2 in 1, 3/5 pin, 15/16 Amps 240 volts

Switch socket combination 2 in 1, 3/5 pin, 5/6 Amps 240 volts

Switch socket combination 2 in 1, 3/5 pin, 15/16 Amps 240 volts

Supply only electrical of following items :

MCB SP 10 to 32 Amp, 240 volts

SPN 40 Amp , 240 volt

TP 63 Amp , 415 volt

PVC insulation tape role 15mm wide, 10 Running meter long

PVC insulated multistranded copper conductor wire of size 1.5 Sqmm, 1100 volts grade

PVC insulated multistranded copper conductor wire of size 2.5 Sqmm, 1100 volts grade

supply only in replacement of 1100 volts grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connections twin core cable flat or circular 4 sqmm complete all as specified and as directed

LED bulb of 7/9 watt

Surface Decorative ultra Slim Round Profile LED Lighting fixture and Extruded Policarbonate, Environmental friendly , Energy Efficient 18 Watt connection complete all as specified and as directed.

Supply and fixing in replacement PVC insulated multistranded Aluminium conductor 1100 volts grade, cross sectional area 25 Sqmm, 3.5 core as in trenches or through floors, fixed on panels/walls with fixing arranements compete all as specified and as directed.

Supply and fixing in replacement PVC insulated multistranded Aluminium conductor 1100 volts grade, cross sectional area 35 Sqmm, 3.5 core as in trenches or through floors, fixed on panels/walls with fixing arranements compete all as specified and as directed.

Supply and fixing in replacement heat shrinkable jointkit suitable for XLPE cable insulated screened PVC bedded armoured electric power cable heave duty 1100 volts grade, with straded aluminium conductor, cross sectional area 25/35 Sqmm, 3.5 core after taking down/out faulty portion as exists compete all as specified and as directed.

Supply and fixing in replecement of 3 pole power contactor 25 Amp 415/440 volts 50 HZ type ML 1.5 Cat part No SS91851

Supply and fixing in replecement of 3 pole power contactor 32 Amp 415/440 volts 50 HZ type ML 2 Cat part No SS90701

Supply and fixing in replecement of Bimetal over load realy for ML 1.5 Starter type 10-16 Amp Cat Part No SS91858OOBO

Supply and fixing in replecement of Bimetal over load realy for ML 2 Starter type range 13-21 Amp Cat Part No SS91859OOCO

Supply and fixing fully automatic Star delta starter type ML in FASD ML 1.5 Cat part No SS91855

Supply and fixing fully automatic Star delta starter type ML in FASD ML 2 Cat part No SS90705

Suppply & fixing in replacement MCCB 160 Amps, 4 pole , breaking capacity 36 KA, connection complete all as specifed and as directed

Suppply & fixing in replacement MCCB 100 Amps, 3 pole , breaking capacity 25 KA, connection complete all as specifed and as directed

Suppply & fixing in replacement MCCB 63 Amps, 3 pole , breaking capacity 16 KA,connection complete all as specifed and as directed

Suppply & fixing in replacement analog type time switch FM 1/Quartz daily 240 volts , AC, 50 Hz code J 6107B 204 connection complete all as specifed and as directed.

Supply and fixing in replacement 60 watt LED street light New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 including making connections with GI pipe 0.6mtr angle braket fixing on wall and connectng to ceiling rose with apropriate wire complete all as specified and as directed

Supply and installation of flanged ends Water Meter woltman type 100 mm , including testing and making good connection with flanged ends, with gasket rubber sheet and nut & bolts etc ISI Marked fixing in horizontal/incline/vertical position, including taking out unserviceable complete all as specified and as directed

Supply and Fixing in replacement of CI Foot valve of following size , Flanged ends, Swing type opration with rubber sheet as per IS-4038 including taking out unserviceable of following sizes complete all as specified and directed Note :- Flanged joints comlete with jointing material shall deemed to be included in the unit rate of this items.

80 mm bore

100 mm bore

150 mm bore

Material and labour including jointing and testing of cast iron sluice valves class PN-1.0, conforming to IS14846 flanged ends drilled having stainless steel spindle with cast iron wheel at top complete with nuts, bolts, washers and rubber gaskets including taking out unserviceable sluice valve and removal from site for the follwing sizes complete all as specified and as directed.

80 mm bore

100 mm bore

150 mm bore

Supply and fixing jointing and testing of cast iron Non return valve without by pass arrangment swing type confirming to IS 5312 flanged ends pressure rating PN 1.0 complete including taking out unserviceable NRV complete all as specified and as directed. Note - Flanged joints complete with rubber jointing materail shall deemed to be included in the unit rate of this item

80 mm bore

100 mm bore

150 mm bore

Supplying , laying , jointing, welding and testing MS Pipe (Heavy class 'C') IS : 1239/3589, of followiing sizes laid in trenches or in Horizontal/Vertical/inclined position or laying on floors for connections for suction, to header and connected to out going water main CI/DI pipe line, for following size including taking out the old unserviceable pipes :- Note:- MS Flanges incl fabrication work will be measured and paid separately.

80 mm dia

100 mm dia

Supply and fixing in replacement Rubber or fiber board gasket for flanged joint suitable for 80/100 mm bore pipe compete all as specified and as directed.

Supply and fixing in replacement of MS flange 80/100 mm bore ,16mm thick duly welded with flange joint including nuts bolts ,washer ,Rubber or fiber board gasket joint of size 100mm size

An amount of Rs 39736/- shall be deducted from BOQ on account of schedule of credit

SM CONSTRUCTION COMPANY

Deven Associates

ARJUN CORPORATION

Ashok Enterprises

P S TRADERS

DHAIRYAE ENTERPRISES

Yadav Enterprises

PUJA ELECTRICALS