E1-0231-2025-ECMC-Additional works to Urban Primary Health Care Centre building at Rangampalayam in ward no 56

Amount

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Designing the Semi Unitised Structural Glazing System with open groove joint as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got approved by the Dept. Officials.) Design the framing system (i.e. male & Female frame) to support vision panels, spandrel panels either with glass or aluminium composite panel, openable, window panels on a continuous framing supported between floors. Also design the split framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated / Monolithic glass, groove width in the system both in horizontal and vertical shall not be more than 20mm. Glazing of panel shall be done only at factory at the controlled atmosphere

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

Water inlet & Outlets

40mm upvc pipe

50mm upvc pipe

32mm upvc pipe

25mm upvc pipe

25mm CPVC Pipe

25mm PVC Pipe

20mm PVC Pipe

40mm upvc Bend

40mm upvc Elbow

40mm upvc Coupling

50mm x 40mm Reducer

50mm Tank Connector

50mm G.M. Gate valves

50mm Coupling

50mm UPVC Elbow

50mm UPVC Tee

50mm UPVC Bend

40mm x 32mm Reducer

32mm UPVC Elbow

32mm UPVC Tee

32mm UPVC Bend

32mm UPVC Coupling

32mm G.M. Gate valves

32mm x 25mm Reducer

32mm FTA

32mm UPVC MTA

25mm UPVC Elbow

25mm UPVC Tee

25mm Brass Elbow

25mm UPVC Coupling

25mm CPVC Elbow

25mm PVC Tee

25mm PVC Elbow

20mm PVC Tee

20mm PVC Elbow

25x20mm PVC Reducer

SS Elbow Action Tap of size 15mm

CP Two Way Bib Cock with Health Faucet

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75mm PVC Pipe

110mm PVC Pipe

160mm PVC Pipe

75mm PVC Elbow

75mm PVC Tee

75mm Aircowl

75mm PVC Bend

75mm PVC Door Elbow

110mm PVC Bend

110mm PVC Elbow

110mm PVC Aircowl

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Supply and Fixing Of PVC Water Tank including all Cost of Labour and Material Charges.

Supply & installation of 1.5 TR split type ac unit air-conditioner with copper coil AC Unit Including cost of all materials at site including cost of 5/8" and 3/8" copper pipe 3 metres length with necessary fitting arrangements etc complete

Supply and laying of 5/8" and 3/8" Copper pipe (Extra beyond 3 metres supplied with AC unit) etc complete

Supply and installation of 5 KVA capacity Automatic Voltage Stabilizer with time elay relay (V-Gurad / Equivalent) etc complete

Earthing arrangements with Maintenance Free earthing with Copper rod of 17.2 mm dia and 3m length with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the std specification and as directed by the Departmental Officers.(M-2568/SOR 2024-25)

Supply and run of 25mmx6mm tinned copper flat with necessary clamps/ supports on wall/ floor/ground for earth connection SD 77

Supply and run of 4 core 16sq.mm PVC copper UG cable includding all cost of Labour and Material and Labour Charges

Supply and run of 4 core 10sq.mm PVC copper UG cable includding all cost of Labour and Material and Labour Charges

Supply and fixing of 12 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100A 4P MCB switch as incoming and 4 nos. 32A 3P MCB,24 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End. SD 597

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 3 nos. 32A 3P MCB , 15 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End SD 585

Supply and fixng of Vertical TPN Distribution Boards (with MCCB Incomer); Double Door; IP43, as per IS 8623 III; Impact resistance IK09; Frame MCCB Incomer & Single Phase/Three Phase MCBs as Outgoing (for power loads exceeding 100A)LOWER END 12 Way, MCCB + 36 Modules (M-1922 SOR 2024-25)

Supply and fixng of 63 Amps Porcelain Fuse Unit (500V) including all Labour and Material Charges (M-1393 SOR 2024-25)

Supplying and Fixing of ACP Cutting Letters of Necessory size and colour of the following sizes including all cost of labours and transport charges.

Emblem (15”)

Supply and fixing of country wood scantling wrought and put up for frames of door and windows including fixing holdfast and all labour charges cost and conveyance of all charges etc., complete as per standard specificationmaterials to site and all labourpipes shall be got approved by Executive Engineer before use on works.

Supplying and fixing door shutters for Medium Density Fibre board of exterior grade, Both side Pre laminated including external lipping with Kiln dried soft wood of 35mm thick conforming to IS 12406 / 1989 with 35 x 12mm T.W. on all edges with necessary adhesive and C.P. screws, including fixing of aldrops, tower bolts, hinges and lock strike plates, putty, fevical, varnish for T.W. lipping with thinner colouring agent etc., The rate includes cost of materials and cost for aluminium furniture fittings such as 6 nos Alu. hinges 125mm, 1 no Alu. aldrop 250 x 16mm, 2nos Alu. tower bolt of 300x12mm and 1 no Alu. tower bolt of 200x12mm, 3 Nos Alu. Handles, 2 nos door stopper with rubber bush incase of Single leaf door inclusive of labour charges for fixing in position etc., complete. All Aluminium furniture fittings are to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1968 for anodic film thickness of not less than 15 microns, The rate is inclusive cost of fevical and fixing charges, transportation, loading, unloading and all other incidential charges, handling charges etc., complete complying with standard specification.

Supply and fixing of Designed Glass including all cost of labour and material and transportation charges

Supply and fixing of 18W 4 Feet LED Fitting with LED Including all Labour Charges.

Supply and fixing of fancy glass shade and 15 W LED Bulb SD 80

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1metre down rod with fan clamp with side plates and cross arm of size 450mm (18") SD 106

Supply & Installation of Decorative type 230V 30 Watts LED Downlight along with Drive Unit Suitable for Elevation Area including transportion unloading and shifting,scaffolding Charges

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position best quality approved make Stainless Steel Sink - 600mm x 450mm x 200mm

Manufacturing, Supplying and Fixing of Stainless Steel Handrails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and FILLING GRAVEL Supplying and filling in foundation and basement with filling crushed stone sand in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification.

Cement Concrete 1:4:8 (One Cement, Four crushed stone sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and laying of Interlocking Paver Block Stone 60mm thk. Over a base layer of crushed stone sandfilling incl. Cost of materials laying and Labour charges etc.,

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 20mm thick in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing fine polished cuddapah slab of following thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 25GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with spag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown olour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the executive Engineer before use on work

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

V DHAMODHARAN (BID ID -1332685)