Development and upgradation of Batadrava Than at Barduwa, Nagaon for the year 2024-25 (Phase-III)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil:: Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of Engineer in- charge.

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 400 mm dia piles

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).

Supplying and stacking at site. 63 mm to 45 mm size stone aggregate

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density.

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level, Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level, Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). 0.91mm Aluminium color coated profile with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm. (Brand: Manaksia, Everlast or as per direction of Engineer-in-Charge)

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : (Brand: Manaksia, Everlast) Ridges plain (500 - 600mm)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

WPC DOOR FRAME Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Celestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In-charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 65 x 150 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws Second class teak wood 35 mm thick

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

Tile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete. Marble tiles (polished) Raj Nagar 8 mm thick

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) : : Along external wall where the apron (existing) is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete::: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) ::: Treatment of soil under existing floors using chemical emul sion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:::With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) : ::Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole : : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing plain multipurpose cement board (Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). 6 mm thick Cement fiber board as per IS: 14862

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes

LPG Cooktop, 4 Buerner, Size:32"X32"X34"

Providing and fixing of 2mm thick UV resistant, colored multi wall polycarbonate sheet in roofing/cladding at any height of level with necessary screw and aluminum snap beading , EPDM beading on MS steel structure (Which shall be paid separately) all complete.

Terracotta Mesh /Tiles: Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta ventilated tiles of height 250/ 300/ 400mm and length of 250/ 300/ 400mm of approved texture,design and pattern having Flexural Strength/ Modulus of Rupture of 14 N/m² (or Equivalent) and maximum water absorption of 10% (or less) tested as per ISO 10545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to a supporting MS rectangular/square pipe section of size 80x60x2mm, 50x50x2mm, 40x40x2mm and 25x25x2mm respectively as per site requirement.

Berge Board: Providing and fixing CNC finished WPC board by organic fibres and/or inorganic synthetic fibres roofing accessories in all colours with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete as per site requirement.

Providing and fixing shingles in slopped chajja

Floor Matt of size 1.750 m X 0.700 m as approved made on sea Grass Rolling Matt eco friedly foldable korai matt, Madurkathi / River Grass / Korai grass and jute threads; 100% natural; No Chemical. Size: This River grass mats for home has been measuring in Length-5.10 feet or 70inch, Width-2 feet or 24inch, Weight-Approx.-900gm

Wooden Moulded Bidd Providing & fixing of the wooden cove bidd with dimensions of 0.075 m x 0.075 m cutting depth refers to how deep the bit can cut into the wood. This specification is essential for determining the thickness of the cove profile you can create. Common cove bits may have a cutting depth of around 0.127 m to 0.025 m (0.0254 m). The shank diameter is the size of the cylindrical part of the bit that fits into the router collet. Common shank diameters for cove bits are 0.0635 m and 0.0127 m. Cover bits typically have two flutes, which are the cutting edges that run along the length of the bit. The number of flutes can affect the smoothness of the cut.

Planters Pot: Providing and Displaying pot for medium sized flower plant / Seasonal/Ornamental/Herbs with natural colour, well developed, fresh & healthy with good foliage as per direction of the officer-in-charge.

Supply and fixing of VOX-infratop, False ceiling of panel sizes 340mm x 2700 mm, resistant to moisture & water. It is durable, scratch resistant EN 438-2 P-25, non flammable EN 13501-1 BS to fire C-S3:D0, in accordance with regulation (EU) no. 305/2011 under the sole responsibility of Manufacture. Increase the sound insulation EN ISO 140-4 EN ISO 717-1 of the room, thermal conduction EN 12664, UV resistance EN-ISO 4892-2 EN 20105-102, Global migration to food substance, No Emmission of Harmful substance.

Supply and fixing of MS Grill work at building porch/ corridor's side slab beam bottom and at the railing fitting area, designed and decorated as per design recommended by Architechture/consultant. Design must be CNC cut and polished as per requirement. (Cost of paint will be extra)

Supply and fixing of WPC made flower pattern at the Head of designer column at building corridor area, designed and decorated as per design recommended by Architechture/consultant. Design must be CNC cut and polished as per requirement. (Cost of paint will be extra)

In situ making of designer column as per Architectural Design or Design Consultant from existing RCC coulmn using extra cement morter adding layers of G.I. chicken mesh (Cost of paint etc will be extra)

In situ making of designer chajja as per Architectural Design or Design Consultant from existing RCC Chajja using extra cement morter adding layers of G.I. chicken mesh (Cost of paint etc will be extra)

Supply and fixing of Cast Iron Made Designer Chair installed at outdoor of the building (Lawn area, Pedestral Area etc), as per the the design and decoration provided and recommended by Architechture/consultant. (Cost of paint etc will be extra)

SANITARY INSTALLATION INDIAN TYPE WATER CLOSET: Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

EUROPEAN TYPE WATER CLOSET: Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

URINAL: Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

WASH BASIN: Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: : White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

BOTTLE TRAP: Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

MIRROR: Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

GLASS SHELF: Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl ,plugs etc., complete.

TOILET PAPER HOLDER: Providing and fixing toilet paper holder :C.P. brass

WASTE COUPLING: Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified. a) Jaquar Make (i) 32mm (HT/FT) (Cat.No.ALD-705 / 709)

SOAP TRAY: Providing, fitting and fixing S.S soap tray / soap dish complete as directed and specified. (i) Jaquar Make, (a) Continental (Cat.No.ACN-1331N)

TOWEL RAIL: 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

TOWEL RAIL: Providing, fitting and fixing CP towel rail complete as directed and specified. (a) Jaquar make (ii) Continental 600mm (Cat.No. ACN-1111N)

COWEL: Providing fitting and fixing PVC cowel of ISI make complete as directed and specified (ii) 110mm dia. PVC cowel of ISI make

GRATING: C.P. Grating (ii) 110mm dia

BIB COCK: Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. : 15 mm nominal bore

STOP COCK: Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. : 15 mm nominal bore

VALVE:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : : 25 mm nominal bore

VALVE:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : : 32 mm nominal bore.

VALVE:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore

VALVE:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 80 mm nominal bore

VALVE: Providing and fixing 25 mm nominal bore ball valve (brass) of approved quality, High or low pressure, with 150mm dia of pragya or equivalent plastic floats complete :

C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. INTERNAL WORK: Concealed work, including cutting chases and making good the walls etc : 20 mm nominal outer dia Pipes

C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. INTERNAL WORK: Concealed work, including cutting chases and making good the walls etc. : 25 mm nominal outer dia Pipes

C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. : 32 mm nominal outer dia Pipes

C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work: 25 mm nominal dia Pipes

C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work: 32 mm nominal dia Pipes

C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work: 40 mm nominal dia Pipes

C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work: 50 mm nominal dia Pipes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 or other ISI approved including joining ,fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (iv) 75mm dia.

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 or other ISI approved including joining ,fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 or other ISI approved including joining ,fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (iv) 75mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (iv) 75 mm dia.

Supplying fitting and fixing 87.5 degree PVC bend with door of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fitting and fixing 87.5 degree PVC bend with door of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia.

Supplying fitting and fixing 87.5 degree PVC bend with door of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

Supplying fitting and fixing 87.5 degree PVC bend with door of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (iv) 75 mm dia.

Supplying fitting and fixing 45 degree PVC bend of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fitting and fixing 45 degree PVC bend of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia.

Supplying fitting and fixing PVC Plain single tee of or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fitting and fixing PVC Plain single tee of or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

Supplying fitting and fixing PVC Plain single tee of or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (iv) 75 mm dia.

Supplying fitting and fixing PVC single tee with door of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fitting and fixing PVC single tee with door of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia.

Supplying fitting and fixing PVC single tee with door of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

Supplying fitting and fixing PVC single tee with door of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (iv) 75 mm dia.

Supplying fitting and fixing PVC single ‘Y’ of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fitting and fixing PVC single ‘Y’ of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia.

Supplying fitting and fixing PVC single ‘Y’ of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

Supplying fitting and fixing PVC single ‘Y’ of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (iv) 75 mm dia.

Supplying fitting and fixing PVC single ‘Y’ with door of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm dia.

Supplying fitting and fixing PVC single ‘Y’ with door of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 75 mm dia.

Supplying fitting and fixing PVC single ‘Y’ with door of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (i) 110mm dia.

Supplying fitting and fixing PVC single ‘Y’ with door of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 75 mm dia.

Supplying fitting and fixing PVC double ‘Y’ plain of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 75 mm dia.

Supplying fitting and fixing PVC double ‘Y’ plain of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (i) 110mm dia.

Supplying fitting and fixing PVC double ‘Y’ plain of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 75 mm dia.

Supplying fiting and fixing PVC cross ‘T’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm x110mm

Supplying fiting and fixing PVC cross ‘T’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 75 mm x 75mm

Supplying fiting and fixing PVC cross ‘T’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (i) 110mm x110mm

Supplying fiting and fixing PVC cross ‘T’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 75 mm x 75mm

Supplying fitting and fixing PVC coupler of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110 mm dia

Supplying fitting and fixing PVC coupler of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iii) 75 mm dia

Supplying fitting and fixing PVC coupler of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (i) 110 mm dia

Supplying fitting and fixing PVC coupler of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (iii) 75 mm dia

Supplying fitting and fixing PVC reducer of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iii) 110 mm x 90 mm

Supplying fitting and fixing PVC reducer of or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 110 mm x 75mm

Supplying fitting and fixing PVC socket plug of or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified. (a) 110 mm

Supplying fitting and fixing PVC socket plug of or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified. (b) 75 mm

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : : 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design: 150 mm dia. R.C.C. pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design::250 mm dia. R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface I recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B

Wiring for light/power plug with 2x2.5 Sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit alongwith 1 No. 2.5 Sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as directed for LP power point ( having 2 nos. 5A switch and 2 nos. 5A socket and LP points )

Wiring for 15/16A power plug with 2x4 Sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit alongwith 1 No. 4 Sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved : 3 Module (125mmX75mm) for LP1- light power Point in rooms and Common place

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved : 1 Module (75mmX75mm) for call bell switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved. : 2 Nos. 5/6amp modular switch for LP2 - TV/ Computer Point.And LP1 and existing switch boards

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved. : 2 nos. 5/6 amps modular socket forLP2- TV Point. And LP1 and existing switch boards

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved. : 15/16 amps modular switch for Geyser and PP and for common lighting switch

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved: 2 x 1.5 Sq.mm + 1 x1.5 Sq.mm earth wire from 15A commmon switch lighting points of corridor and stage lighting as directed.

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved : 2 x 2.5 Sq.mm + 1 x 2.5 Sq.mm earth wire from DB to SB and common switch lighting / fan system as directed

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved : :2 x 6 Sq.mm + 1 x 6 Sq.mm earth wire for sub main from TPN to SPN DB

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved : :2 x 6 Sq.mm + 1 x 6 Sq.mm earth wire for sub main from MDB to TPN DB

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) as required.- for each floor power distribution for hostel and guest house rooms. : 4 way (4 + 12), Double door

Supplying and fixing following way, single pole and neutral ways surface/ recess mounting,MCB distribution board, 240 V, on surface/ recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) as required. - : 8 way Double door for rooms

Supplying and fixing following way, single pole and neutral ways surface/ recess mounting,MCB distribution board, 240 V, on surface/ recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) as required. - : 12 way Double door

Supplying and fixing following way, single pole and neutral ways surface/ recess mounting,MCB distribution board, 240 V, on surface/ recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) as required. - : 16 way Double

Supplying and fixing 5 amps to 32 amps rating, 240 / 420 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. : 10 amps to 32A Single pole

Supplying and fixing 5 amps to 32 amps rating, 240 / 420 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. : 32 amps DP

Supplying and fixing 5 amps to 32 amps rating, 240 / 420 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required : 32A Triple pole for TPN DB incomming

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side as required for each electrical room door .

Installation, testing and commissioning of ceiling fan including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. High Speed Heavey Duty 450 mm sweep

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. High Speed Heavey Duty 300mm sweep

Supply and Installation of 3 blade 1400 mm sweep white Summer Breeze ceiling fan. Make ; Orient or equivalent Havells or CGL make as approved.

Supply and Installation of 3 blade 1200 mm sweep white Summer Breeze ceiling fan. Make ; Orient or equivalent Havells or CGL make as approved.

Supplying and fixing stepped type elctronic fan regulator on the existing modular plate switch box excluding modular plate as required.

Supply of 150mm high speed exhaust fan having automatinc lovour shutter. Make ; Orient Ventilator HS or equivalent Havells, CGL or Panasomic make as approved.

Installation, testing and commissioning of prewired, flourescent fittings / all type of LED indoor ceiling fittings , complete with all accessories and tube etc. directly on ceiling/wall/ False ceiling, including connections with 1.5 sq.mm. PVC insulated, copper conductor, single core cable etc. as required.

Down light square shaped surface mounted 12 watt ,NW (6.5K) LED light fitting. Make - CGL Pearl Nios LCDSPLN-S-12NW 12W CDLor equivalent Surya, Siska, Havells, panasonic as approved for corridor and staircase lighting.

Column Light in alluminium die cast with modern artistic design and white PC diffuser suitable for retrofit LED lamps

UFO LED BOLLARD : Providig and fixing contemporary UFO shape design IO 65 LED bollard wiyh minimum upward light component, ensuring excellent distribution and high system lumen efficacy

SPIKE LIGHT : Supply of Environmental friendly, compact, light weight, energy saving, IP66 LED spike light using COB LED as light source.

1 x 20 W LED 6500K retrofitting polycarbinateT8 tube with in built driver and heat sink double sided connection with compact commercial batten suitable for T8 LED tube Make ;CGL Cat Ref. LT820865 and for batten unilite DMLN1LT8-16 or equivalent Siska or Havells , phillips, bajaj as approved. for small class room lighting

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supply and installation of 12W LED NW bulb on existing angle holder as required. Make ; Siska, Surya, Havells as approved.

Supply of 3 mtrs height street light pole with base plate, arms , nuts & bolts as required for installation of the street light as mentioned above and as directed.

Earthing : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia cover plate having locking arangement and watereing pipe with charcoal / coke and salt as required for panel earthing and transformer body earthing.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing earth bus bar joint made of 20mmx3mm thick 125 mm long with 6 nos. G.I bolts , nuts, chuck nut and spring washers etc. complete as requried

UNDER GROUND CABLE WORKS FOR POWER SUPPLY : Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmoured cable conforming to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEI Or equivalent as approved: 4 Core, 95 sq.mm. Aluminiun conductor XLPE ARMOURED Cable. From Transformer to MDB

Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmoured cable conforming to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEI Or equivalent as approved: 3 Core, 4 sq.mm. Aluminiun conductor XLPE ARMOURED Cable.for out door lighting

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioC70:C80ning, protective covering and refilling the trench etc as required. : Up to 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioC70:C80ning, protective covering and refilling the trench etc as required. : Up to 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. : Up to 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.: Upto 95sq. mm

Supply and making cable end termination with brass compression glands and crimped aluminium lugs following sizes of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade of the following sizes as required.: 4C X95 sq. mm (19mm)

GI PIPES : Supplying and embedding following G.I pipe of medium class for cable entry / road crossing of cable etc. including bending the pipe as required shape as required. b) 40 mm dia

Supply and installation of IP55 Poly carbonate SMC box size 230mmx170mmx105mm door fixed hinged (make - syntex) with 5A SP MCB DIN bar, Earth bar ect. as reqiored with necessary anchor fastner required to fit the box on the wall at required position or as directed .

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.: Above 4.5 metre and upto 6.5 metre (for decorative stright light pole ) as diected.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.for transformer neutral grounding.

Supplying and laying double run 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection terminating with nut, bolt, spring, washer etc. as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. For Lightning Arrester Earthing

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Providing and fixing of G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads. 900 lpm at 35 m Head

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia

100 mm dia

80 mm dia

25 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

b) 100 mm dia with lever

c) 80 mm dia with lever

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm dia

b) 100 mm dia

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket 30 meter

Providing and fixing SS/ Brass ball valve full bore type tested for 20 kg/cm2 with lever and screwed female ends. (Make: Kitz / Zolloto /RB) a) 25 mm dia full bore type

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange a) 150 mm dia

b) 100 mm Dia

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :2 way-100 mm dia M.S. Pipe

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 4 Zone

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in A.B.S. box with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required

Providing and fixing fire hose cabinet fabricated from 4mm thick composite Alum Sheet (in Red colour) fixed on wall with powder coated (in red colour) Extruded Alum. window Section single glazed front door and locking arrangements, painted "FIRE HOSE" written on front including necessary supports approximate size 300 mm Height x 300 mm Width x 250 mm depth. including PCC, MS support, brick work as per drwaing and design and as per the consultant.

Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia as per IS 12992 rated for 20 Kg/Sq.cm ( Make: SB /Newage / Steelage / Sukan)

Supply & Fixing of Fire extinguisher. A) ABC type 4 kg

Supply & Fixing of Fire extinguisher. B) CO2 type 4.5 kg

Supply & Fixing of Fire extinguisher. C) Aqueous Film Forming Foam (AFFF) 9 Ltrs Capacity

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood 50 x 20 mm

RWP : Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.: 110 mm diameter

PAINTING PIPE:Painting (two or more coats) on rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. : 100 mm diameter pipes

PAINTING PIPE : Painting (two or more coats) on rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. : 150 mm diameter pipes

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing bolts including nuts and washers complete.

Dining Table: Supply and installation of Dining Table as supplied by the supplier (Make: Godrej Interior, Model: Mayson ...)

Dining Table : Supply and installation of Dining Table as supplied by the supplier (Make: Godrej Interior, Model: Mingle pod ...)

Dining Table : Supply and installation of Dining Table as supplied by the supplier (Make: Godrej Interior, Model: Bliss ...)

Chair : Supply and installation of Dining table Chair as supplied by the supplier (Make: Godrej Interior, Model: Bliss ...)

Study Table: Supply and installation of Study Table as supplied by the supplier (Make: Godrej Interior, Model: Chocolate ...)

Chair : Supply and installation of Study table Chair as supplied by the supplier (Make: Godrej Interior, Model: OXBO Mid Back ...)

Bed : Supply and installation of Double Bed With Two Side Table as supplied by the supplier (Make: Godrej Interior, Model: Aero ...)

Bed Mattress : Supply and installation of Bed Mattress as supplied by the supplier (Make: Godrej Interior, Model: Ortho ...)

Bed Side Table : Supply and installation of Bed Side table as supplied by the supplier (Make: Godrej Interior, Model: Aero...)

Pillow : Supply and installation of Pillow as supplied by the supplier (Make: Godrej Interior, Model: Nixy...)

Bed: Supply and installation of Single Bed With Side Table as supplied by the supplier (Make: Godrej Interior, Model: Adriana...)

Bed Mattress : Supply and installation of Single Bed Mattress as supplied by the supplier (Make: Godrej Interior, Model: Ortho ...)

Bed Side Table : Supply and installation of Bed Side Table as supplied by the supplier (Make: Godrej Interior, Model: Adria...)

Pillow : Supply and installation of Pillow as supplied by the supplier (Make: Godrej Interior, Model: Nixy...)

Wardrobe : Supply and installation of Wardrobe as supplied by the supplier (Make: Godrej Interior, Model: Adria...)

3 seater Sofa : Supply and installation of 3 seater Sofa as supplied by the supplier (Make: Godrej Interior, Model: Broadway...)

2 seater Sofa : Supply and installation of 2 seater Sofa as supplied by the supplier (Make: Godrej Interior, Model: Orlando...)

1 seater Sofa : Supply and installation of 1 seater Sofa as supplied by the supplier (Make: Godrej Interior, Model: Broadway...)

L shape Sofa : Supply and installation of L shape Sofa as supplied by the supplier (Make: Godrej Interior, Model: Colloseum...)

Center Table: Supply and installation of Center Table as supplied by the supplier (Make: Godrej Interior, Model: Bloom ...)

Corner Table: Supply and installation of Corner Table as supplied by the supplier (Make: Godrej Interior, Model: Edward...)

Executive Table : Supply and installation of Executive Table with attached ERU and Pedestal (1650 W x 700 D x 743 H) (Main Desk) (1000 W x 450 D x 743 H (ERU) (Make: Godrej Interior, Model: Trident Middle...)

Chair : Supply and installation of High Back Chair as supplied by the supplier (Make: Godrej Interior, Model: Bravo...)

Chair : Supply and installation of Visitor's Chair as supplied by the supplier (Make: Godrej Interior, Model: Bravo...)

Back Unit : Supply and installation of Back Unit as supplied by the supplier (Make: Godrej Interior, Model: Aristo...)

Executive Table : Supply and installation of Executive Table with attached ERU and Pedestal (2350 W x 2350 D x 750 H) (Make: Godrej Interior, Model: Aristo...)

Chair : Supply and installation of High Back Chair as supplied by the supplier (Make: Godrej Interior, Model: Emerald...) (Annex-27)

Chair : Supply and installation of Visitor's Chair as supplied by the supplier (Make: Godrej Interior, Model: La Sede...)

Executive Table : Supply and installation of Executive Table with pedestal (1500 W x 750 D x 743 H) (Make: Godrej Interior, Model: Trident Junior...)

Chair : Supply and installation of High Back Chair as supplied by the supplier (Make: Godrej Interior, Model: Bravo...)

Computer Table Chair : Supply and installation of Computer Table as supplied by the supplier (Make: Godrej Interior, Model: Stylo...)

Chair : Supply and installation of Mid Back Chair as supplied by the supplier (Make: Godrej Interior, Model: Oxbo...)

Providing,Supplying and Installation of Godrej factory made modular kitchen cabinets with ISO 9001:2015,ISO 14001:2015,OHSAS 18001:2007,BIFMA registration certificate and Greenguard certified manufactururer. (2200X2700)

Kaff Hob (2 Triple Ring Burner,1 Dual Ring Burner with AutoIgnition)

Kaff Chimney 90 CM

Kaff Sink 60 CM

Aqua Grand, Swift Copper RO Water Purifier For Home +UV+UF+TDS Adjuster+ Alkaline Mineral RO Technology .

SS side table withTwo Shelves, Size: 72"X18"X34"+6"

SS Hot Gas plate, Size: 36"X30"X34"

LPG Cooktop, 4 Buerner, Size:32"X32"X34"

SS Trolly, Three Selves, Size:16"X16"X34"

Counter Chillar Unit, 3 Door, Size:72"X30"X34"

SS Dish Storage rack, Size:72"X18"X34"

Overhead Shelves with Heating system Provided, Size:72"X12"X18"+12"

Work table with two shelves, Size:45"X30"X34"

LPG Cooktop, 3 Burner, Size:72"X24"X34"+6"

MS Single burner stock pot, Size:24"X24"X24"

Service Table with Two Selves, Size:72"X24"X34"

2 Door Refrigeration Unit, Size:600 LTR

Deep Refrigeration Unit, Hard Top, Size:200 LTR

Mixer Grinder (Wet Type), Size:5 LTR

Deep Fryer, Single Unit, Size:5 LTR

SS Soiled Table for dish, Size:40"X24"X34"

3 SINK UNITE, Size:66"X24"X34"+6"

SS Dish Rack, 5 Shelves, Size:30"X24"X66"

SS Pot Wash Sink, Size:36"X36"X30"+6"

SS Pot Rack 3 Shelves, Size:48"X24"X66"

SS HOOD WITH SS FILTER, Size:96"X36"X24"

SS HOOD WITH SS FILTER, Size:36"X36"X24"

SS HOOD WITH SS FILTER, Size:72"X36"X24"

SS HOOD WITH SS FILTER, Size:60"X36"X24"

GI DUCT FOR HOT AIR AND FRESH AIRAPPROX, Size: 80'

EXHUAST FAN HEAVY DUTY, Size:18"

FRESH AIR GRILL, Size:12"X6"

GAS PIPE LINE 6 CYLINDER WITH 6 PO APPROX, Size: 70'

SS RACK 5 SHELF, Size:36"X18"X72"

SS PALLET, Size:60"X24"X6"

ONION/POTATO BIN, Size:18"X18"X36"

Providing and fixing of 2mm thick UV resistant, colored multi wall polycarbonate sheet in roofing/cladding at any height of level with necessary screw and aluminum snap beading , EPDM beading on MS steel structure (Which shall be paid separately) all complete.

Supply, Installation and Commissioning of a Desktop Computer of Model No. :- S500MC511400088W Intel Corei5- 11400 Processor / 8 GB DDR4 Ram / 512GB SSD Drive / Preloaded Microsoft Windows 11 SL Home / Monitor 19.5" Wired Keyboard and Wired Mouse / 3 years Limited Warranty

Supply, Installation and Commissioning of MultiFunction (Print.Scan.Copy). Scanner type-Flatbed Printer Output-Monocrome, Connectivity - USB. Original Toner Cartridge., Page size- A4 Duplex Printmanual Print resolution-Up to 600x600 DPI (1200 DPI effective).Input 150 Sheets Output 100 Sheets. Duty Cycle -30,000 pages per month, Dual digit numeric LED display

Curtain: Providing and fixing of good quality window / Door curtain cloth including 3 Nos of 50 mm fixture for each curtain pipe holder of pipe of size 20 mm as per Engineer in Charge

Curtain: Providing and fixing of good quality window / Door curtain cloth including 3 Nos of 50 mm fixture for each curtain pipe holder of pipe of size 20 mm as per Engineer in Charge

Terracotta Mesh /Tiles: Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta ventilated tiles of height 250/ 300/ 400mm and length of 250/ 300/ 400mm of approved texture,design and pattern having Flexural Strength/ Modulus of Rupture of 14 N/m² (or Equivalent) and maximum water absorption of 10% (or less) tested as per ISO 10545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to a supporting MS rectangular/square pipe section of size 80x60x2mm, 50x50x2mm, 40x40x2mm and 25x25x2mm respectively as per site requirement.

Berge Board: Providing and fixing CNC finished WPC board by organic fibres and/or inorganic synthetic fibres roofing accessories in all colours with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete as per site requirement.

Providing and fixing shingles in slopped chajja

Floor Matt of size 1.750 m X 0.700 m as approved made on sea Grass Rolling Matt eco friedly foldable korai matt, Madurkathi / River Grass / Korai grass and jute threads; 100% natural; No Chemical. Size: This River grass mats for home has been measuring in Length-5.10 feet or 70inch, Width-2 feet or 24inch, Weight-Approx.-900gm

Floor Cushion of size 0.900/0.600 X 0.600 m as approved made on sea Grass Rolling Matt eco friedly foldable korai matt, Madurkathi / River Grass / Korai grass and jute threads; 100% natural; No Chemical.

Wooden Moulded Bidd Providing & fixing of the wooden cove bidd with dimensions of 0.075 m x 0.075 m cutting depth refers to how deep the bit can cut into the wood. This specification is essential for determining the thickness of the cove profile you can create. Common cove bits may have a cutting depth of around 0.127 m to 0.025 m (0.0254 m). The shank diameter is the size of the cylindrical part of the bit that fits into the router collet. Common shank diameters for cove bits are 0.0635 m and 0.0127 m. Cover bits typically have two flutes, which are the cutting edges that run along the length of the bit. The number of flutes can affect the smoothness of the cut.

Mirror: Providing & Fixing of Mirror with 6mm thick commercial ply backing

Steel Dustbin: Supplying & Fixing of Stainless Steel Mesh Dustbins Round Shape 11 Liter, Durable Bin, Multipurpose Wastebasket with dimension of 0.250 m x 0.350 m

Photo Frame: Providing & fixing in position second class teak made Photo Frame at all height with sizes 10-20 mm thick, maximum 900 mm in length and maximun 900 mm in wide, in approved colour, texture and finish with necesasary profiled edges fixed with SS screws, in each tile to frame work made of second class teak wood of size 20x15 mm in centre of each tile and bottom and top of work height. 4mm plywood material shall be laid over backside of the photoframe as per site requirement.

Providing & fixing in position second class teak made Photo Frame at all height with sizes 10-20 mm thick,maximum 1500 mm in length and maximun 1200 mm in wide, in approved colour, texture and finish with necesasary profiled edges fixed with SS screws, in each tile to frame work made of second class teak wood of size 20x15 mm in centre of each tile and bottom and top of work height. 4mm plywood material shall be laid over backside of the photoframe as per site requirement.

Planters Pot: Providing and Displaying pot for medium sized flower plant / Seasonal/Ornamental/Herbs with natural colour, well developed, fresh & healthy with good foliage as per direction of the officer-in-charge.

Supply and fixing of VOX-infratop, False ceiling of panel sizes 340mm x 2700 mm, resistant to moisture & water. It is durable, scratch resistant EN 438-2 P-25, non flammable EN 13501-1 BS to fire C-S3:D0, in accordance with regulation (EU) no. 305/2011 under the sole responsibility of Manufacture. Increase the sound insulation EN ISO 140-4 EN ISO 717-1 of the room, thermal conduction EN 12664, UV resistance EN-ISO 4892-2 EN 20105-102, Global migration to food substance, No Emmission of Harmful substance.

Supply and fixing of MS Grill work at building porch/ corridor's side slab beam bottom and at the railing fitting area, designed and decorated as per design recommended by Architechture/consultant. Design must be CNC cut and polished as per requirement. (Cost of paint will be extra)

Supply and fixing of WPC made flower pattern at the Head of designer column at building corridor area, designed and decorated as per design recommended by Architechture/consultant. Design must be CNC cut and polished as per requirement. (Cost of paint will be extra)

In situ making of designer column as per Architectural Design or Design Consultant from existing RCC coulmn using extra cement morter adding layers of G.I. chicken mesh (Cost of paint etc will be extra)

In situ making of designer chajja as per Architectural Design or Design Consultant from existing RCC Chajja using extra cement morter adding layers of G.I. chicken mesh (Cost of paint etc will be extra)

Supply and fixing of Cast Iron Made Designer Chair installed at outdoor of the building (Lawn area, Pedestral Area etc), as per the the design and decoration provided and recommended by Architechture/consultant. (Cost of paint etc will be extra)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface I recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B

Wiring for light/power plug with 2x2.5 Sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit alongwith 1 No. 2.5 Sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as directed for LP power point ( having 2 nos. 5A switch and 2 nos. 5A socket and LP points )

Wiring for 15/16A power plug with 2x4 Sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit alongwith 1 No. 4 Sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved : 3 Module (125mmX75mm) for LP1- light power Point in rooms and Common place

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved : 1 Module (75mmX75mm) for call bell switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved. : 2 Nos. 5/6amp modular switch for LP2 - TV/ Computer Point.And LP1 and existing switch boards

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved. : 2 nos. 5/6 amps modular socket forLP2- TV Point. And LP1 and existing switch boards

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved. : 15/16 amps modular switch for Geyser and PP and for common lighting switch

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved: 2 x 1.5 Sq.mm + 1 x1.5 Sq.mm earth wire from 15A commmon switch lighting points of corridor and stage lighting as directed.

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved : 2 x 2.5 Sq.mm + 1 x 2.5 Sq.mm earth wire from DB to SB and common switch lighting / fan system as directed

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved : :2 x 6 Sq.mm + 1 x 6 Sq.mm earth wire for sub main from TPN to SPN DB

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved : :2 x 6 Sq.mm + 1 x 6 Sq.mm earth wire for sub main from MDB to TPN DB

Installation, testing and commissioning of ceiling fan including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Supplying and fixing stepped type elctronic fan regulator on the existing modular plate switch box excluding modular plate as required.

Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing, commissioning etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Earthing : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia cover plate having locking arangement and watereing pipe with charcoal / coke and salt as required for panel earthing and transformer body earthing.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing earth bus bar joint made of 20mmx3mm thick 125 mm long with 6 nos. G.I bolts , nuts, chuck nut and spring washers etc. complete as requried

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioC70:C80ning, protective covering and refilling the trench etc as required. : Up to 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioC70:C80ning, protective covering and refilling the trench etc as required. : Up to 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. : Up to 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.: Upto 95 sq. mm

Supply and making cable end termination with brass compression glands and crimped aluminium lugs following sizes of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade of the following sizes as required.: 4C X95 sq. mm (19mm)

GI PIPES : Supplying and embedding following G.I pipe of medium class for cable entry / road crossing of cable etc. including bending the pipe as required shape as required. b) 40 mm dia

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.: Above 4.5 metre and upto 6.5 metre (for decorative stright light pole ) as diected.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. For Lightning Arrester Earthing

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Providing and fixing of G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Supply, fitting and fixing of ceiling suspended slim panel high lumen output LED lighting fixtures of Havell make ( Cat. Ref. Venus NEO 2x2 PLR 36WLED857G2), 36W fittings or equivelent make of PHILIPS/Havell's/ Jaquar as per prior approval of Deptt .

Supply, fitting and fixing of ceiling surface mounted downlighter fixtures of Havells make of 9W Panel Light (Round) 9W 6" fittings or equivelent make of PHILIPS/Havell's/ Jaquar as per prior approval of Deptt.

Supply, fitting and fixing of ceiling surface mounted downlighter fixtures of Havells make of 6W COB Light (Round) 6W fittings or equivelent make of PHILIPS/Havell's/ Jaquar as per prior approval of Deptt.

SITC of LED Batten Light 20W

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. High Speed Heavey Duty 450 mm sweep

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. High Speed Heavey Duty 300mm sweep

Supply and Installation of 3 blade 1400 mm sweep white Summer Breeze ceiling fan. Make ; Orient or equivalent Havells or CGL make as approved.

Supply and Installation of 3 blade 1200 mm sweep white Summer Breeze ceiling fan. Make ; Orient or equivalent Havells or CGL make as approved.

Supply of 150mm high spped exhaust fan having automatinc lovour shutter . Make ; Orient Ventilator HS or equivalent Havells, CGL or Panasomic make as approved.

Supply, fitting and fixing of Bulk Head Light fixtures with necessary CG boxes if required of Havells make ELLIPSE NEO 13.5 W( Jeta compacto 50 watt/Jeta Neo 70 Watt) fittings or equivelent make of Jaquar /Philips as per prior approval of Deptt .

Providing, Installation Testing and Comissioning of Main Panel for the Kitchen Building as per design with incommer 320A MCCB and Outgoings as per requirement

Supply and Installation of 3 blade 1200 sweep very silent very powerful double bearing ceiling fan. Make ; Orient Aeroquiet or equivalent Havells or CGL make as approved. For guest house room and common room.

Supply of 300 mm high spped exhaust fan. Make ; Orient air flow or equivalent Havells, CGL or Panasomic make as approved. For Toilets

Supply of 450 mm industrial heavy duty high spped (1400 rpm) exhaust fan . Make ; Orient or equivalent Havells, CGL or Panasomic make as approved. For Toilets

Down light square shaped surface mounted 12 watt , NW (6.5K) LED light fitting. Make - CGL Pearl Nios LCDSPLN-S-12NW 12W CDLor equivalent Surya, Syska, Havells, panasonic as approved for corridor and staircase lighting.

Column Light in alluminium die cast with modern artistic design and white PC diffuser suitable for retrofit LED lamps

UFO LED BOLLARD : Providig and fixing contemporary UFO shape design IO 65 LED bollard wiyh minimum upward light component, ensuring excellent distribution and high system lumen efficacy

SPIKE LIGHT : Supply of Environmental friendly, compact, light weight, energy saving, IP66 LED spike light using COB LED as light source.

1 x 20 W LED 6500K retrofitting polycarbinateT8 tube with in built driver and heat sink double sided connection with compact commercial batten suitable for T8 LED tube. Make; CGL Cat Ref. LT820865 and for batten unilite DMLN1LT8-16 or equivalent Syska or Havells, Phillips, bajaj as approved for small class room lighting

Supply and installation of 12W LED NW bulb on existing angle holder as required. Make; Syska, Surya, Havells as approved.

Supply and installation of 3 mtrs height street light pole with base plate, arms , nuts & bolts as required for installation of the street light as mentioned above and as directed.

UNDER GROUND CABLE WORKS FOR POWER SUPPLY : Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmoured cable conforming to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEI Or equivalent as approved: 4 Core, 95 sq.mm. Aluminiun conductor XLPE ARMOURED Cable. From Transformer to MDB

Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmoured cable conforming to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEI Or equivalent as approved: 3 Core, 4 sq.mm. Aluminiun conductor XLPE ARMOURED Cable.for out door lighting

Supply and installation of IP55 Poly carbonate SMC box size 230mmx170mmx105mm door fixed hinged (make - syntex) with 5A SP MCB DIN bar, Earth bar ect. as reqiored with necessary anchor fastner required to fit the box on the wall at required position or as directed

BRACKET LIGHT : Of havells Floretine WL 1LS E27 ABR

Design, manufacture, supply, installation, testing and commissioning of cubicle type panel fabricated out of 14 SWG CRCA sheet steel , floor mounted totally enclosed switch baord suitable for use of 415 volts , 3 phase, 50HZ complete with aluminium bus-bar and all accessories including supply and fixing of following incoming and outgoing switchgears. The sheet steel shall undergo minimum 7 tank treatment followed by finishing powder coating of min 60 micron thickness. Incomer: FP 125 A 50 KA Ics= 100% Icu MCCB with microprocessor based release with buit in E/F Protection, extended rotary handle and spreader terminal - 1 Nos. Digital Ammeter 0-200A 3 Phase 4 Wire Accuracy Class 1 as per IEC 62053-21 Bezel dimension (W X H)=96 X 96 mm: 1 No. Digital Voltmeter - 0-500V 3 Phase 4 Wire Accuracy Class 1 as per IEC 62053-21 Bezel dimension (W X H)=96 X 96 mm : 1 Nos. CT 200/5 240V 3 Phase 4 wire Freq 50Hz+/- 5% Accuracy Class 0.5S : 1 Set SP MCB with 10KA breaking capacity of rating 6 Amp : 03 Nos RYB Indicating Lamps : 1 set, BUS BAR : 800 A TPN AL. bus bar with coloured heat shrinkable PVC sleeve-1 Set, Outgoings: 63 A 3P MCCB, 25 KA - 2 Nos , 40 A 3P MCCB, 25 KA - 6 Nos , 32 A TP MCB, 25 KA - 1 No.. B - series, 32 A DP MCB, 25 KA - 4 No.. B - series , EARTH BUS.

Supplying and fixing 12 Watt Down lights for common area including connection etc. as required.

Supplying and fixing 06 Watt Down lights for toilet including connection etc. as required.

Supplying and fixing 10 Watt LED batten light(Mirror light) including connection etc. as required.

Supplying and fixing 2x3 Watt Up Down lights including connection etc. as required.

Supplying & fixing LED bollard light including connection etc. as required.

Supplying & fixing Gate top light including connection etc. as required.

Supplying & fixing Wall light including connection etc. as required.

Supplying & fixing Spot light (projector series) including connection etc. as required.

Supplying & fixing ventilating fan 250 mm including connection as required.

Supplying & fixing Hensel cable junction box (KF 1610 G)

Supplying & fixing Hensel cable junction box (KF 1006 G)

Providing & laying 1.1 KV grade XLPE insulated aluminium armoured conductor cable on surface of the wall of building with required size of aluminium shadle and screw etc. as required. a) 3.5 Core 120 Sqmm Cable

b) 3.5 Core 50 Sqmm Cable

c) 3.5 Core 35 Sqmm Cable

d) 4 Core 16 Sqmm Cable

Providing & laying 1.1 KV grade copper unarmoured conductor cable on surface of the wall of building with required size of aluminium shadle and screw etc. as required. a) 4 Core 4.0 Sqmm Cable(Un Ar)

b) 3 Core 4.0 Sqmm Cable(Un Ar)

c) 3 Core 2.5 Sqmm Cable(Un Ar)

d) 3 Core 1.5 Sqmm Cable(Un Ar)

Providing & fixing Acoustical Veneer Wall Paneling. The work will also include all cost for creation of niches for installation of AV equiments and electrical fittings wherever required. The veneer and polish shade and finish will be as per consultant. The cost will include all accessories or any material which may be required to complete the work as per specification, drawings and as directed by the consultant.

Providing & fixing Acoustical CNC Jali Cut laminated MDF board Column Cladding. The work will also include all cost for creation of niches for installation of AV equiments and electrical fittings wherever required. The veneer and polish shade and finish will be as per consultant.

Providing & fixing Acoustical Board Paneling having 20mm thk x 600mm x 600mm fire resistant Wood Wool Board fixed over a Framework consisting of 48x36x34mm, 0.55mm thick Drywall stud channel at 600mm c/c with floor channel 50x32mm at bottom and top including all accessories and fittings filled with 50mm thk 1000 GSM environment and human health friendly polyester wadding to be held in position with chicken mesh of 18mm 24SWG. Leaving a minimum 50 mm airgap. The wood wool board will be finished with matt enamel spray paint complete as per consultants drawings & instructions. The paint shade and finish will be as per consultant.

Providing & fixing of 100mm X 15mm Teak Wood Skirting on joiney of wall panelling with floor, duly polished. The wooden skirting will be finished with PU Matt / Glossy Polish complete as per consultants drawings & instructions. The polish shade and finish will be as per consultant.

Providing & fixing of double leaf Acoustic Doors 76mm thick, STC 45. Acoustic Door having infill of Rockwool 64kg/ M3 density, Sandwiched between One Calcium Silicate Boards without asbestos, Brucite and Meerschaum having a density not more than 1150kg/ M3 along with Sound dempening Sheet and Commercial Ply both side with heat activated intumescent fire seal strip of size 10x4mm and EPDM Gaskets around the frame are used to enhance acoustic properties. 1mm thick Mica laminates facing on both sides in desired shade and colour. Hard Wood Door frame size is 125x90mm with double rebate. Door Hardware Provision as per choice of Architect/client's approval. Door Hardware like SS Hinges, Door closer, SS Handle 300mm, Dead Lock, Tower Bolt, Automatic Drop Down Seal all inclusive.

Providing & Fixing of Glass Fibre Acoustical Suspended Ceiling System with Square Edge Tiles of size 600 X 600 mm and 15 mm thickness. The tiles shall have sand texture visual with acoustical punchers, Humidity Resistance (RH) of 95%, NRC 0.9(Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥84% as per ASTM E-1477, Thermal Conductivity k = 0.052- 0.057W/mK, Colour white/Black, Fire Performance of class 0/1as perBS 476 Part 6/7 and Class A as per ASTM E84 with 15 mm bevelled Tegularedge and8mm drop in module size of 600 x 600mm. It shall be suitable for Green Building application, with Recycled content of 49%. The tile shall have certifications from GRIHA and GreenPro thereby confirming that it is an environment friendly product. The tile shall be laid on 15 mm wide T - section flanges colour Black (matching to tile color) having roll formed double stroke rotary stitching on all Tgrid

Under Deck Insulation: Providing and Fixing a layer of 50mm thick mineral wool insulation pads of density 48kg/cum below roofing sheets, fixed with chicken wire mesh & steel wires.

Providing and fixing Carpet Tiles flooring 500mmx500mm having nylon/PP tufted /10" Loop pile construction, back to back modified bitumin backing having a denisty of atlest 4100 g/m2, having a pile height of 6mm, confirming to EN98, suitable for wet cleaning using wet vaccum cleaner duly pasted to the ready floor base as per on manufactures sepecifications. The shade & design of the carpet will be confirmed by the consultant.

Providing and fixing of Manual Roller Blinds comprising of Sunscreen fabric (Basket Weave) with Openness factor 5% having composition of 22% Polyester and 78% PVC of weight 475gsm±5% & thickness 0.68mm±5% and having fire resistance standard – DIN(4102) & BS Test,B2 & BF 5867 part2(Type B) Tensile strength (Warp 170N±10%, Weft 125N±10% as per ISO 544674). Color fastness 6-7/8 (ISO 105 B02-1994) Xenon Arc Lamp. The control clutch drive unit engineered heavy duty chain drive pulley operating system consisting of gear clutch housing and locking plug containing minimum 6 ribs and inserted at minimum of 37mm into roller tube. It is self lubricating Exclusive clutch with safety pins for secure bracket installation and unlocking pin for quick manual removal. Universal clutch is most convenient for large windows down to the smallest windows. It shall be driven by a ball chain pulley with ball chain and can be positioned at Right hand or Left hand side of the shade

20 KVA On-Line UPS System (DELTA/ Orion or equivalent make as approved by the Deptt.) with PWM-IGBT technology 360V AC Input (300V – 470V A 3 Ph input- 3 Ph output With Isolation Transformer 70KW output with 0.85 output PF 30 min backup using SMF battery

Panasonic Standard Throw (0.91 to 2.5) Multimedia Projector (MMP) With 1920 x 1080 (Full HD) Resolution

Wireless Presentation Device Karmer via Connnect

Installation accessories for Video System

Wall Mount speakers 800-Watt Column Speakers

Power Amplifier

18-Channel Digital Mixer

Head Worn Microphone

Handheld Vocal Microphone

Cables and Connectors

Installation Charges

HVAC: Providing and Fixing 5 Star Rating of BEE Air Cooled Split Type Air Conditioners complete with indoor unit (IDU), Outdoor unit (ODU), surface / concealed coper Refrigerant piping with insulation (EP Foam pipe section) up to 3 Mtr. (IDU to ODU) copper power cable up to 4 Mtr. (at least 3CX 2.5 Sqmm, PVC Insulation, FRLS copper wire) (IDU to ODU), R-22/R-410 Refrigerant , PVC drain pipe (dia 15mm) Remote, suitable for 400/230V +10% of 50 Hz, 1/3 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with scroll/reciprocating/ rotary compressor, with ODU Stand. 1 TR Capacity

1.5 TR Capacity

2 TR Capacity

2.5 TR Capacity

3 TR Capacity

Providing and fixing extra copper piping with insulation after 3Mtr.

Providing and fixing square link cage (25x25mm, 18 gauge) with MS angle (35X35X5 mm) including primer with paint, welding etc and all other required accessories and work.

Providing and fixing Stabilizer (240V, 50 HZ, 5KW), 16 Amp 3 pin top and all accessories and work

Providing and fixing wall mounted ODU stand for split air conditioning and all accessories etc.

PVC Drain Pipe.

Supplying, Installation, testing and commissioning of 64Ch Digital NVR, Supports IP Cameras upto 12 Megapixels, All channel 4K resolution, 64 Channel Sync playback, 2 HDMI 1080p output, 64 Ch Audio and 1 mic in/out ports, 8 x 10 TB SATA, 2 USB, 1 RJ45 & 1, Incomming bandwidth support 300 MBPS & RS485 Ports and centralized video management system. product should be BIS approved, NDAA Compliant.

Supply, Installation, Testing & Commissioning of 5 MegaPixels Fixed Type Bullet Camera - 3.6mm Fixed Lens - H.265 Compression - Upto 30mtr IR - Triple Stream - IP65 / IK10 Rated - NDAA Compliant - InBuilt SD Card Slot

Supply, Installation, Testing & Commissioning of MegaPixels Fixed Type Dome Camera - 2.8mm Fixed Lens - H.265 Compression - Upto 30mtr IR - Triple Stream - IP65 / IK10 Rated - NDAA Compliant - InBuilt SD Card Slot

8TB Survillance HDD, 7200RPM, Designed for 24/7 Usage.

HDMI Cable 15 MTR long.

55" LED DISPLAY FULL HD (4k DISPLAY)

6 core un-armoured multi mode optical fiber cable.

UTP CAT6A Cable (400 mtr)

Supplying, Installation , Testing and Commissioning of EPABX system equipped with 16 analog extensions , 4 CO Line having system features like-Programmable class of service for (STD/ISD/LOCAL) dialing as per need,Caller ID information for both internal and external callers ,Voice prompts ,Call forwarding,Brokers Call,Automatic call transfer,Conference call,Call pick up, etc.

Operator Console with DSS 40 keys, Speaker Phone.

Supply of Gsm Gateway 2 port To Provide redundent voice Link

Push Button Telephone Desk Phone with CLI.

Supplying, installation , testing and commissioning of 20 pair locking facility waterproof rectangle steel/PVC MDF Box with krone module having each krone connection slot have to accept upto wires of equal diameter complete as required.

10 Pair DP Box with Modules, expandable upto 20 Pairs

a) 2 Pair 0.5 mm sheathed telephone cable

b) 10 Pair jelley filled 0.50mm flexible telephone cable.

Enterprise Grade Inbuilt controler base Dual Band (2.4 & 5 GHz) Indoor Access Point :Proposed Access Point must be multifunctional high performance 802.11ac wave 1 or better.Must support 2x2 multiple-input multiple-output (MIMO).Must supports up to 1.2Gb/s wireless data rate and up to 64 simultaneous clients association in single Access Point.

Supplying & fixing 1 no RJ45 UTP CAT 6 outlet with 1 no, 1 module white plate & 1 no. 1 module metal flush (Legrand - Mosaic) including connection etc. as required.

L2 Full managed Ethernet stand alone chassis provides 24 PoE RJ-45 10/100/1000 BaseT, 1Gig BaseX combo and 2 SFP Gigabit uplinks ports. 1U by 1/2 rack form factor, internal AC power supply ( 370W PoE budget), fan less on 19" rack mount kit, power cord, manuals/software access cards, RJ-45 to DB-9 adaptors and rubber tabletop feet. (HP/CISCO/ALCATEL)

L2 Full managed Ethernet stand alone chassis provides 24 RJ-45 10/100/1000 BaseT, 1Gig BaseX combo and 4 SFP Gigabit uplinks ports. 1U by 1/2 rack form factor, internal AC power supply, fan less on 19" rack mount kit, power cord, manuals/software access cards, RJ-45 to DB-9 adaptors and rubber tabletop feet. (HP/ CISCO/ALCATEL)

24U Rack/800x1000/CKD/Castor T2/19" Adp/Perforated Doors/Side Panels, Horz. Cable Organiser Box Type, Shelf/1000, Shelf/Key Board/19"Rty/1000, Mounting Hardware-CR (Pack of 10), PDU 1Ph, 230V, 32A, 12 x 5/15A IRP 16A MCB x 2 Circuites - 7.3KVA, ITE / Server Rack Air Circulation module/Tower Mount/360CFM, Cable Basket/36U/100/NRS1

Supply, installation and commissioning of Server and storage system for digitization.

5 kVa Online UPS system with 120 minute battery back up on full load with necessary warrenty on battery and in system

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required 150 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia

100 mm dia

80 mm dia

25 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

b) 100 mm dia with lever

c) 80 mm dia with lever

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm dia

b) 100 mm dia

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket 30 meter

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 18.18.3 25 mm nominal bore

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads 2280 lpm at 56 m Head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 56 m Head

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 2280 lpm at 56 m Head

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange a) 150 mm dia

b) 100 mm Dia

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :2 way-100 mm dia M.S. Pipe

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 4 Zone

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in A.B.S. box with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required

Providing and fixing fire hose cabinet fabricated from 4mm thick composite Alum Sheet (in Red colour) fixed on wall with powder coated (in red colour) Extruded Alum. window Section single glazed front door and locking arrangements, painted "FIRE HOSE" written on front including necessary supports approximate size 300 mm Height x 300 mm Width x 250 mm depth. including PCC, MS support, brick work as per drwaing and design and as per the consultant.

Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia as per IS 12992 rated for 20 Kg/Sq.cm ( Make: SB /Newage / Steelage / Sukan)

Supply & Fixing of Fire extinguisher. A) ABC type 4 kg

Supply & Fixing of Fire extinguisher. B) CO2 type 4.5 kg

Supply & Fixing of Fire extinguisher. C) Aqueous Film Forming Foam (AFFF) 9 Ltrs Capacity

Supply, installation, testing & commissioning of 100 mm dia Bourden type, Stainless Steel dial type glycerine filled pressure gauge including brass isolation valve and pipe having caliberation of 0-16 Kg/cm2.

SHREE GAUTAM CONSTRUCTION CO. LTD. (BID ID -244310)