SPECIAL REPAIR TO BLDG NO. 212 INCLUDING PROVISION OF INTERLOCKING PAVER BLOCKS,RETAINING WALLS AND IRON RAILING WORK IN OTHER RANK MARRIED ACCN BLDG NO. 299, 300,301, 213, 248, 195, 223, 194, 302 AND 306 AT MIL STN NAHAN UNDER GE CHANDIGARH

Amount

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each including cutting holes in walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.50 Sqm but n. exc 4.0sqm each including cutting holes in walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified.

Dismantling mild steel work of any description not otherwise provided for in any location and any position complete all as specified and directed.

Dismantling wall and ceiling boards (fibre pulp, insulation, etc) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified and directed.

Demolitioin of cement conc in ground floors and pavings n.exc 15cms thickness (below or above GL).

Demolitioin of cement conc(reinforced) in ground floors and pavings n.exc 15cms thickness (below or above GL).

Demolition and breaking up drain pipe 100mm bore salt glazed stone ware/AC/PVC pipe complete all as specified.

Taking down steel water tubing 15mm to 20 mm with all fittings from walls, ceiling and floors, complete all as specified and directed.

Dismantiling timber scantling in fillets, rail, posts, rafter, purlins, etc under 40Sq.cm in section complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises

Dismanntling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete all as specified and directed.

Demolition of brickwork or stone/boulder masonary, built in lime mortar including quoins arches, pillers etc, but excluding ashlar facings, dressed stone work and precast concrete article built in cement mortar or cement lime mortar complete all as specified and directed.

Dismantling water tanks 500 ltr complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots complete all as specified and directed.

Rendering 15mm thick on fair faces of brick work or concrete surfaces , finished even and fair without using extra cement on walls in cement mortar1:4, (using WPC) complete all as specified and as directed. Note:- WPC shall be measured and paid seprately.

Rendering 15 mm thick on brick work or concrete surfaces, finished even and smooth without using extra cement on walls in cement mortar 1:6, in patches complete all as specified and as directed.

M&L for preparation of newly plastered surfaces and applying two coats of exterior grade acrylic emulsion paint over a coat of primer and over and including layer not less than 1.0mm thick of wall care putty complete all as specified and as directed.

M&L for preparation of newly plastered surfaces and applying two coats of acrylic distemper/ distemper oil emulsion (OBD) over and including 2mm thick wall care putty in any pattern complete all as specified and as directed.

M&L preparing & finishing on old walls with acrylic smooth exterior paint of required shade(New work)(Two or more coats applied @1.67ltr/10 Sqm over and including priming coat of exterior primer applied @2.20 kg/Sqm complete all as specified and as directed.

M&L for preparation and applying two coats of acrylic distemper/ distemper oil emulsion (OBD) on old wall/ceiling surfaces with and including a coat of primer and thin layer of 2mm thick wall care putty incl complete removal of existing treatment complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M&L for preparation and applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surface of any description ,not otherwise described complete all as specified and directed.

M&L for preparation and applying one coat of synthetic enamel paint over old painted steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, complete all as specified and as directed.

M&L for preparation and applying one coat of synthetic enamel paint over steel & iron surfaces of any description, not exceeding 10 cm in width or girth, unconnected with other painting or when painted in different tint complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and directed.

S & F in repair vitreous China wash basin, (white) Flat back, size 550x400 mm including cast iron brackets, PTMT waste coupling and PVC waste pipe complete all as specified and directed.

S&F in repair vitreous China Squatting pan, 'orrisa pattern, size 580x440 mm (white) with integral foot rests with and including 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S & F in repair vitreous china wash down water closet pan (pedastal pattern) white (exclusing fixing bolts, flushing cistern and flush pipe)

S&F in repairs 10 ltr capacity PVC vlaveless syphonic action type flushing cistern low level,white with inlet ball valve,float and handle including brackets,complete all as specified and as directed.

S&F in repair (centre hole mixer), cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15 mm bore iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm dia bib taps CP brass,fancy type,long body, screwed down, screwed for iron pipe complete all as specified and directed.

S&F in repair 15mm dia Angle cock chromium plated brass fancy type, screwed down , high pressure, scrwed both ends for iron pipe complete all as specified and directed.

S & F Continuous (piano) hinges 30 mm wide , mild steel, bright finish or electro galvanised complete all as specified and directed.

S&F in repair 100 mm Hasp and staple, safety type, aluminium anodised hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F 4mm sheet glass ordinary quality and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed.

S & F 4mm Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 in each pane complete all as specified and directed.

S & F galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.4mm and fixed stainless steel wire staples or in aluminium frame work /shutters complete all as specified and as directed.

S & F in repair 17-18mm thick HDHMR board high density, water, termite, boer and fungus resistant, laminated both sides fixed with screws to timber frame work as in cupboard shelves, shutters, bathroom doors, kitchen cabinets etc complete all as specified and as directed by Engr-in-Charge

Cutting chases in stone wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

M&L 15mm GI tubes medium grade with all fittings & fixed complete to walls or ceilings or laid in floors complete all as specified and directed.

M&L 20mm dia GI tubes medium grade with all fittings & fixed complete to walls or ceilings or laid in floors complete all as specified and directed.

S&F in repair 20mm dia SS 304 curtain rod including brackets, decorative balls/caps on both ends of curtain rods with comp fittings complete all as specified and directed.

S&F ball catchers for cupboard and kitchen cabinets both male & female part (making each set) complete all as specified and directed.

S&F in repair concealed type stop cock chromium plated with long shank and cup

M&L for Framed work such as grills,gratings,etc..with ends of bars shouldered and/or riveted,or forged into spikes, framed guard bar, for tank staging , conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F in repairs Brass chromium plated shower rose 125mm size,with complete fitting complete all as specified and directed.

S&F in repairs kitchen sinks with drainage board made of stainless steel 1 mm thick with plugs washers and CP waste coupling including bedding in cement mortar to dward wall or including fixing cantilever brackets and connection union to pipe overall size 37' x 18' x 8' complete all as specified and directed.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre incl fixing hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long for false ceiling with and incl 12mm thick perforated particle boards or tiles with 02 coats of oil bound distemper on boards for insulation and accoustic purposes, 60cm x 60cm in size all as specified for size of grid 605 x 605mm

Providing and fixing anodised aluminium work for door windows, ventilators, casement/sliding shutters and partitions with extruded built up standard tabular and other sections of approval make fixed with rawl plugs and screws or with fixing clips or with expansion hold fastner incl neceesary filling up of gaps at junctions at top bottom & sides with required PVC neoprene belt etc. Aluminium section shall be smooth rust free straight mitred and jointed mechanically where ever required including cleats angles, aluminium snap beading for glazing/panelling, CP brass/stainless steel screw incl providing hinges/pivot and making provision for fixing of fittings where ever required. (Note:- The rate is inclusive of rollers, Maruti locks/star locks, robber beading, rubber seal etc for sliding/casement shutters required for satisfactory operations of window/ventilators/doors or as directed by Engineer-in-Charge. 2. panel fillings other than aluminium filling and necessary fittings shall be measured and paid for seoparately under respective items.)

S&F 1000 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified.

S & F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S & F in repairs 15mm dia bore pipe Ball brass valves high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Taking down CI soil waste or vent pipe 100mm bore including all fittings like trapes,bends,junctions etc from any situation complete all as per specified and as directed.

Taking down CI soil waste or vent pipe 75mm bore including all fittings like trapes,bends,junctions etc from any situation complete all as per specified and as directed.

S & F 110MM PVC SWR Pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S & F 75 MM PVC SWR Pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors.

S & F in repair 110MM PVC SWR Bends any radius complete all as specified and directed.

S & F in repair 75 MM PVC SWR Bends any radius complete all as specified and directed.

S & F in repair 75MM PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S & F Door strip (snake guard strip) complete all as specified and directed.

S&F 5.00mm thick glass corner shelf set (one piece) having stainless steel perimeter border all as specified and as directed.

S&F in repairs towel (600 mm long) rack stainless steel with peg set all as specified and as directed.

M & L Cement concrete type B -1, 1:2:4 type B-I (20mm graded stone aggregate) 25 mm thick, complete all as specified and directed.

M & L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) with old size bricks disignation 7.5 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L coloured vitrified tiles (scratch and strain resistant tiles) 10mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and include 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Glazed ceramic coloured,,tiles 450x350x6-7mm thick in vertical surfaces such as skirting,dados and risers to steps over and including 10mm thick in CM (1:4) complete all as specified and directed.

M&L Black Granite stone 18-20 mm thick as in kitchen platform incl rounding or bullnosing the exposed edges over and including 15 mm thick screed in CM 1:3 complete all as specified and directed.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as specified and as directed.

S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, valleys, gutters etc. fixed with self tapping screws complete all as specified and as directed.

S & F Fe 410-w(Gde E 250)quality B rolled mild steel roof trusses (framed) trussed, purlins, crane gantries, rails and framing (beam, tee, angle, channel or flat sections) including distance pieaces cleats etc complete all as specified and directed.

Material & labour for chequered cement concrete coloured tiles 20cm x 20cm x 25mm thick, with grey cement and pigment, jointed and pointed in neat cement slurry in floor laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L 75 mm thick Cement concrete type D2,1:4:8 (40mm graded stone aggregate) as in sub base,path,floor, hardstanding complete as as specified and directed.

S&F factory made solid PVC Door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening as per specified.

S&F factory made solid panel PVC Door shutter 30mm thick (stiles)consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain cover PVC 'C' channel having PVC strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails on either side & as gap insert for top rail & bottom rails, panelling of plain colour PVC sheet to be the fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification and drawing.

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 100mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 125mm size, Stainless Steel, D type with back plate, handle and fixed with screws complete all as specified.

S&F 250mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including bolts and nuts complete all as specified.

S&F 30mm thick Factory made flush shutters, solid core construction, with block board core and plywood face panels commercial type on both sides

M&L for 30mm thick Factory made 2nd class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified and directed.

M&L for 75 mm thick cement concrete type C-2, 1:3:6 using 40mm graded stone aggregate as in plinth protection, finishing the cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

Forming contraction (dummy) joints 25 mm deep x 10mm wide, filled with sealing compound Grade A complete all as specified and as directed.

S & F Pressed steel frames 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

S & F Pressed steel frames 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

S&F in repairs Kitchen Plate Rack (600x750x250mm) made of 0.63 mm thick stainless steel sheet to accommodate (8 plate) complete all as specified and directed.

S&F in repairs waste pipe 32mm dia flexible for Sink all as specified and as directed.

M&L Cement concrete (1:3:6) type C2 using 40mm graded crushed stone aggregate as in bed to drain pipes 100mm bore including packing under and haunching against the sides of pipes after laying and testing complete all as specified

M&L 100mm bore (internal dia) salt glazed stone ware pipes grade A laid in trenches on concrete bed to required slope jointed complete all as specified.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and n exc 10 sqm on plan and getting out in soft and loose soil complete all as specified.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm complete all as specified.

Removal of excavated soil to a distance not exc 50 metre and depositing where directed at a level not exc 1.5 metre above the starting point complete all as specified.

M&L RCC 1:2:4 (nominal mix) type B-0(1:2:4) using 12mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and inshelves and the like complete all as specified.

Formwork to soffits of suspended slabs such as roof slabs, floor slab, landings and similar work not exceeding 200mm thick, horizontal or sloping finished rough complete.

TMT bars 10mm dia and over cut to length , bent to shape required including , cranking hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete.

S&F in repair SS 304 cutlery trays of size 370x485x100mm and 0.6mm thickness 4 modular kitchen concept including fixing with slider, rollers for front and back movement complete all as specified and directed. Make: HAFALE/Hettich/Godrej/Kaff/Harrison or equivalent as approved by GE.

S&F in repair SS 304 multipurpose tandem box drawer of size 850x500x200mm and 0.6mm thickness having space for deep and shallow storage for bottom cabinets including blum tandem runners fixing clips, Tandem runners cover cap, front fixing fascia bracket and mounting plate and all necessary fitting and fixture and Dtype cabinet handles premium quality gloss chrome/SN Finished 150mm long matt finished, front and back movement complete with and incl tray containers and utensils complete all as specified and directed. Make: HAFALE/Hettich/Godrej/Kaff/Harrison or equivalent as approved by GE.

M&L stone walling built in CM 1:6 of random rubble uncoursed, well bonded, solidly hearted built in retaining walls, abutment and sililar work complete all as specified and directed.

M&L stone walling built in CM 1:6 of random rubble uncoursed, well bonded, solidly hearted built in retaining walls, abutment and sililar work but except(old stone received) complete all as specified and directed.

Flush pointing to random rubble, uncoursed or brought up to coursed CM 1:4 complete all as specified and directed.

Sand filling under floors or in foundations including watering and consolidation

Material & labour for 80mm thick non skid pre polished coloured interlocking paver block made with electro vibro technology with rubber/ PVC moulded of not less than compresive strength 30 Kg/Cm and shape and size confirming to IS 15658-2006 of M-40 Grade with grey cement and pigment complete all as specified and directed by Engineer in Charge. Note:-The sample shall be got approved from the GE before bulk procurement and lots shall be got tested independently by the GE.

All as per srl item No 103 here-in-before but 60mm thickness of M-35 Grade

Material & labour for providing cement concrete Type B1 1:2:4 (20mm graded crushed stone aggregate) kerbs or mut stops, rounded or chamfered on edges etc complete including necessary form work complete all as specified and directed.

M&L providing for PCC 1:3:6 Type C-1 using 20mm aggrgate as in coping, apex stone, complete all as specified and directed.

M&L Cement concrete in surface channels and drains in cement concrete 1:3:6 type C2 (20 mm graded stone aggregate) complete all as specified and directed.

Extra for forming fair finished drain or channel 60 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.

Two coats of cement base paint on new wall surfaces including complete removal of existing treatment and all necessary preparation and wetting and curing, complete all as specified.

M&L for Hard core of gauge exc. 63mm but not exc 100mm,deposited,spread and levelled in layers not exc. 15 cm thick, watered and rammed/rolled to a true surface complete all as specified.

Excavation over areas, not exc 1.50m deep and getting out in hard/dense soil complete all as specified and directed.

Forming embankments including raising (or lowering) earth spreading in layer n exc 30cm thick watering, ramming/rolling and finishing to required size shape etc n exc 1.5m high from the base, complete all as specified and directed.

All as per srl item No 112 here-in-before but exc 1.50m not exc 3.00m high from the base

All as per srl item No 112 here-in-before but exc 3.00m not exc 4.50m high from the base

All as per srl item No 112 here-in-before but exc 4.50m not exc 6.00m high from the base

M&L for removing surplus excavated material exc 1.50km but not exc 5.00km and depositing where directed.

M&L broken stone or boulders hand packing (any thickness) at back of walls over arches etc and raising/lowering to the required level.

M&L RCC M-25 ( 20mm graded trap stone aggregate )for concrete as in foundation, rafts, footings, plinth beams, bases of columns, including attached pilaster and buttresses etc., complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, base of columns, raft and raft beams, plinth beams, vertical, for fair finished surfaces, complete all as specified and as directed.

M&L TMT bars, 6mm to 8mm dia. cut to length , bent to shape required including , cranking hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including ,fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. all as specified and directed.

Taking down MCB DB /Old Meter box of any size and disposal under schedule of credit and making good disturbed surfaces all as specified and directed.

Taking down old unserviceable light fittings any type and removal from site and making good disturbed surfaces of walls, ceiling etc complete all as specified and directed by Engineer-in-Charge to match with existing surface all as directed.

M&L for point wiring using approved colour coding as per IS ( for Phase and neutral) with copper conductor 1.5 sqmm ( Cross sectional area) single core multistranded FRLS ,PVC insulated and unsheathed cable 1100 volts grade,conforming to IS drawn and including PVC concealed coduit with fittings ISI marked ,terminated in modular switch boxes incl 1.5 sqmm (cross sectional area ) single core ,multistranded ,FRLS PVC insulated and sheathed cable as earth continuity conductor connected to earth dolly for one light point control by one way switch complete all as specified and directed.Note: 1.colour code of wiring should be ( for phase ,red,neutral ,black & earth wire green) 2.Modular switch sockets fan regulators shall be measured and paid separately under respective items deemed to be included in the quoted rates.

- Ditto - all as per item No - 124 above but one call bell point controlled by one bell push point.

- Ditto - all as per item No - 124 above but for one ceiling fan/exhaust fan point.

- Ditto - all as per item No - 124 above but for one 3 pin 5 amp socket on same board all as directed.

- Ditto - all as per item No - 124 above but for one 3 pin 5 amp socket on indipendant board all as directed.

- Ditto - as per item No 124 here in before but with 4 sqmm copper conductor for 15 amp socket with 2.5 sqmm earth continuity conductor

S&F of Modular snap switch SP one way 5/6 Amps suitable for 1 Module complete all as specified and directed.

S&F of Modular Bell push ,SP 5/6 A suitable for 1 Module complete all as specified and directed.

S&F of Modular socket 5 pin 5/6 Amps suitable for 2 Module complete all as specified and directed.

S&F of Modular snap switch SP one way 15/16 Amps suitable for 1 Module complete all as specified and directed.

S&F of Modular socket 5/6 pin 15/16 Amps suitable for 2 Module complete all as specified and directed.

S&F of Modular Fan step Regulator electronic, 120 watts,2 Module complete all as specified and directed.

Supply and fixing of Modular Indicator lamp, 2 Module size complete all as directed.

S&F of Modular blanking plate suitable for 1 Module complete all as specified and directed.

S&F of Modular white cover plate incl Modular base frame & powder coated Modular sheet metal concealed box for 12/8 module complete all as specified and directed.

All as per Item No-138 above but 6 module complete all as specified and directed.

All as per Item No-138 above but 3/4 module complete all as specified and directed.

All as per Item No-138 above but 2 module complete all as specified and directed.

S & F of ceiling rose surface backalite 65mm x 50 mm, two to three terminals complete all as specified and directed.

Supply and fixing of lamp holder insulated body with back plate suitable for any type of fitting incl one No of LED Bulb 15-18 Watts Base B-22 retrofit type all as specified and directed.

S & F of Electric bell, AC, 230volts, single phase, Ding Dong type complete all as specified and directed.

Supply and fixing of Indoor Decorative LED box type suitable for fixing ceiling/wall with aluminium base directly retro fit LED tube Light , 22 watt, , Color: Cool day light 4 ft white Operating Voltage: 140-270 volts complete with all accessories internally pre wired and including up with three core PVC copper flexible cable of size 23/0.0076 from ceiling rose to connector block complete all as specified and directed LED batten & LED tube rod shall be of same brand.

Supply and fixing of LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete all as specified and directed. Make :Halonix Model No:HLBH-15-10-CW-INV or equivalent in CG/Philips/Havell's.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC,decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing of decorative fancy light fitting 1x15 watt retrofit/non retrofit type holder(base B-22 or E-27) incl 01 Nos of LED bulb 15 watts with connector block, etc. complete with all accessories prewired and including connecting up with two core round flexible copper conductor cable in white with suitable size complete all as specified and directed

Supply and fixing of 25 watt LED batten with opal diffuser ,IP20, battery backup upto 4 hrs.Fitting should have inbuilt 2 No's of Li-on battery of 2600mA each.Housing of fixture should be of extruded aluminium Efficacy of fixture >100LPW,P>F>0.9,THD<30% complete all as specified and directed.Make: Halonix Model No: HLB-08-25-CW-INV or Equivalent in Crompton Greaves,Bajaj,Philips,Havell's.

Supply and fixing of 60 watt LED inverter RTC(street light with inbuilt RTC (Real Time clock) for Auto on/Auto Off. Housing made of Pressure die cast aluminium ,top maintainable and with clear heat resistant toughned glass , have secondary lens for better optics, should have LM80 certified LED of CREE,NICHIA, OSRAM,SEOUL make only with constant current RTC enabled electronic driver with 5KV SPD,IP66. Street light shall have inbuilt Li-on battery of 5200mAH and shall have>1.5 hrs battery backup at inverter load in case of power failure,Efficacy > 100LPW,CRI>70,THD<10%,PF>0.95,cut off voltage at 300 Volt + 10% and suitable for 50mm mounting GI Pipe complete all as specified and directed.Make: Halonix Model No: HLSLD-ML04-60-CWL-INV-RTC or Equivalent in Crompton Greaves, Bajaj, Philips, Havell's.

Supply and fixing of security light fitting bracket made up of 25/32 mm dia medium grade pipe of length 0.9 mtr with bending in shape by hot or cold method with 2 nos 50x4 mm MS flate clamps with nut bolts and washer etc all as directed

Supply and fixing of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 12 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc flushed on the existing wall , to match with existing surface and making all necessary connections complete all as directed.Make : L&T / Legrand Lexic Hager/Havell's/Indo Asian.

S & F of isolator DP 2 pole 63 amp 230 Volt complete all as specified and directed.

S & F of isolator SP, 6-40 Amps, 230 Volts complete all as specified and directed.

M&L of blanking plate suitable for MCB DB's SPN/TPN complete all as specified and directed.

Earthing complete with Galvanised steel earth plate electrode of size 60x 60cm x 6mm thick electrode buried directly in ground (earth pit not less than 2.25 meters deep below the normal ground level) with top edge of the plate not less than 1.5 m below normal Ground Level connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts and washers and earth lead protected by 15mm dia GI pipe medium grade connected to main distribution board/ earthing test point all as shown on electrical plate No-03 of SSR Part-1 and all as specified including testing on completion.Note: The unit rate shall also include for excavation, earth work in hard/dense soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bars @ 150mm c/c both ways , GI funnel with watering pipe 20 mm dia, wire mesh, salt and charcoal, protection pipe for earth lead upto 7.50m long complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified in SSR part-II earth lead wire and protection pipe beyond 7.5m shall be measured and paid separately.

Excavation in trenches n exc 1.5 mtr wide and n exc 1.5 meter in depth for foundation, laying of cable, pole etc or for shafts, wells, cesspits, manholes pier holes etc not exc 10 sqm on plan and not exc. 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed by Engr-in-Charge

Returning, filling in including spreading, levelling, watering and well ramming excavated soil in layers not exceeding 25 cm thick each, back in trenches after cables have been laid and tested,poles, stays , struts have been errected and tested , all as specified.

Removing excavated surplus (soil) obtained from excavation to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete, all as specified.

M & L for Brick protection for LT cable with sub class "B" bricks laid dry and flat abutting each other with gaps between adjacent bricks not exceeding 10mm with width equal to length complete all as specified and directed by Engr-in-Charge

Sand cushioning with clean dry sand to cables with layer of sand 8cm before laying of cable and 15cm thick after laying of cable complete all as specified. Note : For payment purpose punned thickness of 18cm shall be measured against spread thickness of 23cm as mentioned in para 19.75 of SSR part-I

Supply and laying of GI tubing, light grade, 50 mm bore dia as cable protection fixed on walls/poles/laid in trenches complete including dismantling corroded GI pipe all as specified and as directed.

Supply, laying , jointing ,testing and commisioning LT underground cable 1100 volts grade XLPE insulated and steel strip or wire armoured heavy duty with multistranded aluminium conductor 16 Sqm 2 core size including taking out unserviceable complete all as specified and directed. Note:- (i) Excavation and earth work cable protection and sand cushioning shall be measured and paid seperately .

Taking down and re fixing the existing water geyser/ Ceiling fan/exhaust fan any type and any size after necessary servicing/greasing complete incl painting all as specified and directed by Engr-in-Charge to match with existing surface complete all as specified and directed.

Material and labour for road / path way any type (Concrete) cutting , including excavation, returning filling in, spreading, leveling, well ramming in layers, soiling with broken boulders/ stones, WBM 7.5 cm thick coarse aggregate received from dismantling the existing road, premix, carpeting 25 mm thick using ready mix patch mate material, rolled and compacted for road patch repair work, complete all as directed.

M&L in replacement of fabrication of sheet metal enclouser to accommodate 01 Nos electric meters of suitable size deep and 1.6 mm thick MS sheet, powder coated, bakelite sheet with side hung shutter including provision of locking arrangement and niche covered with 4 mm thick plain glass , including locking arrangement & open Wiring coverd with Flexible Pvc Pipe of suitable size complete all as specified and as directed.

Supply and fixing of Exhaust fan 300 mm sweep heavy duty complete with self closing MS louvers, mounted in suitable opening arrangement and suitable for operation on 230/240 Volts single phase, 50 Hz,1400 RPM , AC supply with and including two core PVC insulated, PVC sheathed copper conductor flexible cable 24/ 0.2 mm and making all necessary connection and fixed by using 4 Nos 100 mm long 10 mm dia bolts, nuts and washers and grouted in wall in CM 1:3 (including opening of wall etc) completed all as directed.

Supply and fixing of Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 300m and making all electric connections complete all as specified and directed.

Supply and fixing of Water heater (Geyser) Storage type , vertical type 5 star rating electric 230 volts AC,50 Hz capacity 25 ltrs with 15 Amps plug top fixed on wall by means of anchor fastners-04 Nos ,12mm dia and 150mm long grouted into wall and making good the disturbed surfaces with existing finishes complete all as specified and directed.

Supply and fixing ceiling fans (Remote sensor type)complete with blades, down rods, electronic regulator and ccessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) ® with provision of cable PVC insulated and sheathed FRLS grade 3 core 1.0 sqmm copper conductor flexible wire 1100 volts grade from porcelain connector /ceiling rose to ceiling fan complete all as specified and directed.Make:USha/Havell's/Crompton Greaves.

Supplying and fixing smart single phase two wire dual source prepaid energy meters BIS 15884 marked in existing meter board / floor panels with pre payment capacity touch keypad based digital having current range 10-60 Amp 240 Volt accuracy class 1.0 alongwith parallel home display split unit with inbuilt load control switch containing provision for TOD and RTC, inbuilt feature to sense the DG mode through PLSI, dual source registration wrt grid as well as DG supply and dynamic load allocation facility from grid and DG, capable to define for tariff slabs, happy hours and holiday definition making all electric connections complete all as specified and directed.Make: Securemeter/L&T/Schneider Elect.Note: The UNSV old one Item Srl No 167 to 171 is MES property and will be handed over to MES Store Yard .

M/S SHANTI SARUP DINESH CHAND

M/s Krishan Aggarwal