SPECIAL REPAIR TO BLDG NO P- 372/1 To 04 AND SPL REPAIR TO TOILET BLOCK OF BLDG NO P-1063 UNDER AGE B/R (P) AT ITARANA ALWAR

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) all as specified & as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3 Kg of cement per square metre all as specified & as directed.

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge.

Taking down chowkat or frame with shutters area not exc. 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts complete all as specified

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts complete all as specified.

Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar.

M&L for cutting holes of depth 15cm in stone walls built in cement mortar for inserting holdfasts/hooks (stays) etc and making good dismantled portion in cement mortar 1:3, complete.

Raking out joints/pointing to random rubble or polygonal rubble uncoursed or brought up to courses in cement /lime mortar.

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete.

M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed. Note :- Reinforcement shall be measured and paid for separately.

M&L for providing cement concrete in roof kerb or mud stop, rounded or chamfered on edges 1:2:4, type B-1 using 20mm graded crushed stone aggregate complete all as specified and directed.

M&L for 15mm thick rendering in two layer on fair faces of brick masonry or concrete surfaces of walls consisting of 1st layer of 10mm thick plaster in CM 1:6 and 2nd layer (setting coat or top layer) of 5 mm thick plaster in CM 1:4 mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished fair & even, complete, all as specified. Note : - Supply only water proofing compound shall be measured and paid for separately.

Supply only integral water proofing compound (ISI marked).

M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and directed.

M&L for rendering 15mm thick in cement plaster 1:6 on stone masonry surfaces or surfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 10mm thick in cement plaster 1:4 on stone masonry surfaces or surfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

M&L for glazed ceramic tiles (coloured) 450mm x 350mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) (Ist quality) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

Material and labour for non skid ceramic tiles (coloured) Ist quality 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

Material and labour for non skid ceramic tiles (coloured) Ist quality 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

M&L factory made 60mm thick vibratory moulded precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as Specified & directed.

Supply and fixing flush shutter of 30mm thick solid core construction with block board core and plywood face panels with both faces covered with decorative face veneer with lipping/frame and laminated on both sides with self closing circular knob for locking arrangement magic eye and safety chain complete all as specified & as directed.

Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed by Engineer in charge. Note : The door shall be specified as per pattern & drawing as specified by Engr-in-Charge

S&F factory Made Solid PVC Moulded Door Shutter, With Particle Board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing in SSR.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications.

Supply & fixing factory made box type steel windows with side hung shutters including box type hinges with steel handles and peg stay with glazing bars dovetailed or welded including one shop coat of Zinc Chromate primer complete all as specified.

Supply & fixing factory made box type steel windows with side hung shutters including box type hinges with steel handles and peg stay without glazing bars dovetailed or welded including one shop coat of Zinc Chromate primer complete all as specified.

S&F box type factory made steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of Zinc Chromate primer complete all as specified.

Supply and fixing galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, glazing in repairs, complete all as specified.

Supply and fixing 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified.

Supply & fixing vitreous china squatting pan (Orissa pattern) water closet (white) size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) complete including connection to trap and flushing pipe antisyphonage pipe etc including provision of PCC (1:7:12) type F2 in filling complete all as specified.

Supply and fixing as in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F as in repairs 15mm bore Stop valve/ Angle valve fancy type with long shank and cup of cast copper alloy chromium plated screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union. Make:- Prayag, Jaquar , Prima

S&F chromium plated brass shower rose screwed for 15 mm bore GI pipe, 125 mm bore fixed in repairs.

S&F as in repairs 15mm bore Stop valve fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union.

S&F in repairs vitreous china wash hand basin, white, flat back of size 580mm x 450mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F 32/38/40 mm dia PVC flexible waste pipe 80cm long with socket for union, for WHB/urinal/sink complete all as specified.

Taking up or down 20mm bore steel tubing and connection incl cleaning for refixing or removal to store.

Refixing old steel tubing and connection in new or old position (wall, ceiling, floor etc) of 20mm bore of pipe.

M&L galvanised steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

Taking up or down 15mm bore steel tubing and connection incl cleaning for refixing or removal to store.

Refixing old steel tubing and connection in new or old position (wall, ceiling, floor etc) of 15mm bore of pipe.

M&L galvanised steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

S&F repairs sink made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 495mm x 420mm bowl size 410mm x 330mm x 160mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, all as specified and directed.

S&F as in repairs 20mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

Supply and fixing in repairs 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I

S&F as in repairs Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and as directed.

S&F PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F as in repairs tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges.

S&F as in repairs Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40 gms) all as directed.

S&F CP soap dish complete all as specified and directed.

S&F Towel Ring, fancy type, Chromium plated, fixed with brass screws and wooden/plastic cleats as approved by the GE.

S&F in repairs 15 mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule. Make:- Prayag, Jaquar , Prima

Supply and fixing 75mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified including taking out old unserviceable PVC pipe with fittings.

Supply and fixing 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified including taking out old unserviceable PVC pipe with fittings.

S&F 75mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including taking out old unserviceable pipe of any type with fittings and making good around complete all as specified and directed.

Supply and fixing 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified including taking out old unserviceable PVC pipe with fittings.

S&F UPVC (SWR) floor trap dia of outlet 75mm, with PTMT grating including jointing with solvent cement including taking out old unserviceable trap.

S&F in repair 75 mm bore UPVC (SWR) bends any radius complete all as specified.

Supply and fixing in repair 75 mm bore UPVC (SWR) bends any radius with access door complete all as specified.

S&F in repair 110 mm bore UPVC (SWR) bends any radius complete all as specified.

Supply and fixing in repair 75 mm bore UPVC (SWR) bends any radius with access door complete all as specified.

S&F in repair 110 mm bore UPVC (SWR) ISI marked single branch piece(single 'T' ) equal or unequal provided with access door complete all as specified.

S&F in repair 110 mm bore UPVC (SWR) ISI marked single branch piece(Double 'T' ) equal or unequal provided with access door complete all as specified.

S&F in repair 110 mm bore UPVC (SWR) ISI marked single branch piece(single 'T' ) equal or unequal provided with access door complete all as specified.

Supply and fixing 110 mm bore PVC (SWR) vent cowl complete all as specified.

S&F in repairs stack clamp made out of MS flat 50 mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 75mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified & as directed.

Supply & fixing butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified.

Supply & fixing butt hinges of size 100mm extruded aluminium alloy with galvanised mild steel hinge pin type B-21 anodised complete all as specified.

S&F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

Supply and fixing 300 mm long mild steel sliding door bolts clip type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, ISI marked complete all as specified.

Supply and fixing 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified

Supply & fixing aluminium handle 125mm size cast type, anodized complete all as specified.

Supply and fixing 200 mm long mild steel barrel tower bolts, stove enameled black with bright bolts and fixed complete all as specified

Supply and fixing 150 mm long mild steel pressed handle, oval type, stove enameled black complete all as specified

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified.

S&F in repairs Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified.

S&F in repairs stainless steel Kitchen plate rack of overall minimum size 900mm x 750mm and 230mm deep, with partitions for small/large plates etc made out of stainless steel 24 Gauge, fixed with rawl plug and CP steel screws all as directed. Note : Weight of rack shall not be less than 4.50 Kg.

M&L for pressed steel shutter 1mm thick including pressed steel frame of 1.25 mm thick sheet, 12mm dia MS rod for locking, two Nos chromium plated handle and one Godrej pattern lock including two coat of spray painting over a shop coat of primer, complete,

S&F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified & as directed.

S&F in repairs stainless steel drapery rod of 20 mm inner dia (in lengths as directed) of approved colour with & including decorative finial at both ends and pair of stainless steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed.

M&L for mild steel TMT bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia, complete, all as specified and directed.

All as per serial item No. 92.00 here-in-above but 8mm dia.

Material and labour brick work with subclass 'B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified.

Material and labour brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors and similar works of Gde E-165(Fe 290) including welding etc. complete all as specified & as directed.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Grade E-165 (Fe 290) including necessary welding etc. and fixed in position.

S&F mild steel framed work as in doors / gates / steel frames etc. of angle or other section with gusset plates, rails, braces, etc., complete of Gde E-165(Fe 290), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position complete.

Treatement for sunken portion is as follows :- (i) Demolition of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (ii) M&L for providing 12 mm dia holes of 40mm deep @2.00m c/c at junction of beams and columns as co-ordinal points for inserting/pouring cement slurry by pressure grouting for sunken floors of toilet , includind sealing the holes with CM 1:3, all as specified and as directed by Engineer - in - Charge. (iii) M&L for water proofing plaster for sunken portion in CM 1:3, 20 mm thick in two coats with water proofing compound at the rate of 2% by weight of cement and finishing the surface even and smooth without using extra cement. (WPC will be measured and paid seperately). (contd....) (iv) M&L for applyin evenly two coats of industrial bitumen 85/25 at the rate of 1.20 Kg/Sqm in each coat over vertical surfaces and floors of sunken floors of toilet including cleaning of surfaces. (v) M&L for PCC 1:7:12 type D2 using 40 mm graded stone aggregate as in filling (sunken portion). etc. (vi) M&L for PCC 1:2:4 type B0 using 12.50 mm graded stone aggregate, mixed with WPC @ 2% by wt. of cement, as sub base, 75mm thick. (WPC will be measured and paid separately.) on top (vii) M&L for plastering in CM 1:4, 15 mm thick with water proofing compound at the rate of 2% by weight of cement and finishing the surface seven and fair.(WPC will be measured and paid seperately) (contd....)(contd....) Note :- Above includes (a) Test again of water tightness by pounding for 72 hours & rectify defects if any till total elimination of defect. (b) The sunken portion shall be tested for leakage / seepage / dampness by pounding with water for 72 hours. In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. The process of grouting and testing shall be repeated till leakage / seepage / dampness is eliminated. (c) Horizontal flat area to be measered.

M&L preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified.

Material and labour preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L preparation of new untreated wooden surfaces of any description, not exc. 10 cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of pink primer.

M&L preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick white wall care putty all as specified & as directed.

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over & 1mm thick wall care putty all as specified & as directed.

Material and labour preparation of newly plastered surface of ceiling & applying three coats of white wash complete all as specified.

M&L brooming down old decorated plastered/asbestos cement surfaces of ceilings & applying one coat of white wash complete all as specified.

M&L brooming down old decorated surfaces of walls, plastered including cornices, pilasters etc and applying one coat of white wash complete all as specified.

Material and labour preparation of newly plastered surface of walls & applying three coats of white wash complete all as specified.

M&L preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified & as directed.

Material and labour preparation of newly plastered surface of walls & applying two coats of cement base paint over a coat of primer complete all as specified.

Forming groove of size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer incliding removel of wooden battens, repair to the edges of panels and finishing the groove complete all as specified and direction of the Engineer-in-charge.

M&L for PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in levelling course of floors and roofs 25mm thick finished fair & even complete all as specified & as directed.

M&L for 20mm thick Granite slab of approved shade, as in platform etc, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) including required cutting to suit the size of oval type wash hand basin over & including 20mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

Supplying and fixing in repair factory made PVC shutter of 18 mm thickness consisting of panel of 18 mm thick celluca ply of density 600 Kg.cbm density with prelaminated sheet on one side cut in desired size of shutter and fixed with frame as in cabinet boxes with shelf and shutter full size fitted above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc including dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. Note : Items like cupboard knobs, stainless steel channel, CP plate clip hinges are included in the mentioned rates and as per manufacturesrs specification and drawing.The measured area shall be front elevation.

Supply & fixing hasp and staple of size 75mm aluminium anodized safety type with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screws.

S&F fixed in repair vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified & as directed.

Supply & fixing vitreous china urinal, half stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified.

Supply & fixing vitreous china urinal, partiotion of size 300mm x 700mm.

S&F in repairs vitreous china wash hand basin, white, (Counter type) under counter flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F in repairs 15mm bore fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes.& fly nuts, screwed for iron pipes.

S&F in repair swivel shower rose(fancy type) chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union all as specified and directed

Supply and fixing in repairs 75 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls complete all as specified.

Supply and fixing in repairs 100mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls complete all as specified.

S&F in repairs cast iron floor trap of 75 mm bore, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified & as directed.

S&F in repairs cast iron floor trap of 100 mm bore, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified & as directed.

S&F in repairs cast iron trap ‘P’ or ‘S’ for 100 mm bore pipe complete all as specified & as directed.

S&F 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.

S&F in repairs 75mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door.

S&F in repairs 100mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door.

AARSINFRATECH

Radha Enterprises

TARKESHWAR DASS CONSTRUCTION COMPANY

M/s ASK Enterprises

Hitesh Construction

M/S JALANDRA CONSTRUCTIONS

GAR CONSTRUCTIONS