Loading…
Loading…
Tender Value
₹80.2 L
EMD Value
₹1.6 L
Closing Date
13 Apr 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
WORKSOL
19 conditions · 8 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less, where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure- VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender .
b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of dvertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway.
In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing.
Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates.
In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Definition of Similar Work : - Any work involving commissioning of Telephone Exchanges/IP exchange/ Intercom facilities.
28 conditions · 12 needing a document upload
Please submit your bank details i.e. Name of the Bank along with Bank Branch Code, Account Number, IFSC Code, and PAN Number.
Please furnish list of plant and Machinery available on hand own and proposed to be inducted own and hired to be given separately for the subject work.
Please furnish list of Works on hand indicating Description of Work, Contract Value, Approximate value of balance work yet to be done and Date of award.
Please furnish list of Works completed in last seven financial years giving Description of Work, Organization for whom executed, approximate value of contract at time of award, Date of award and Date of Completion. Date of actual Start, Actual Completion and Final value of Contract shall also be given.
Please furnish list of personal, organization available on hand and proposed to be engaged for the subject work.
Documents to be Submitted Along with Tender: (i)The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / HUF etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (ii)Following documents shall be submitted by the tenderer.
(a)Sole Proprietorship Firm: All documents in terms of Para 10 of the Tender Form (Second Sheet) above (As per GCC-2022).
(b)HUF: i) A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) above. as per GCC-2022.
(c)Partnership Firm: All documents as mentioned in para18 of the Tender Form (Second Sheet) as per GCC-2022.As per GCC- 2022.
d) Joint Venture (JV): All documents as mentioned in para 17 of the Tender Form (Second Sheet).as per GCC-2022.
(e)Company registered under Companies Act2013: (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv) All other documents in terms Para 10 of the Tender Form (Second Sheet) above.(Eligibility Criteria) above as per GCC-2022.
(f)(i) A copy of LLP Agreement (ii) A copy of Certificate of Incorporation (iii) A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv) An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet)..(Eligibility Criteria) above as per GCC2022.
(g)Registered Society & Registered Trust: (i) A copy of Certificate of Registration (ii) A copy of Memorandum of Association of Society/Trust Deed (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. (iv) A copy of Rules & Regulations of the Society (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) above.
The tenderer whether sole proprietor/ a company or a partnership firm/registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association /Board resolution, failing which tender shall be summarily rejected.
Any DIPP certificate submitted along with the tender document for, exemption of EMD should be valid on the date of opening of the tender, else the tender offer will be summarily rejected.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderers may also upload the following documents along with his/their tender: The tenderer may upload statement, which shall contain organizational set up and working systems to be adopted by the successful tenderer s during the operation of the contract. It shall contain the details of man power and machineries in the prescribed format and details of methodology for planning, execution, monitoring and completion of the project. The methodology so adopted shall suit to the nature of work and shall also comply fully with best practice and current regulations. A comprehensive detailing for each activity like setting-up organization, safety plan, execution plan, quality assurance plan, sequence of work to achieve the mile stones, ensure targeted progress and quality and in turn deployment of resources, risk analysis and its mitigation strategy shall be given communication arrangement within his organization and with the railways for decisions, progress or any other matter connected with this project to ensure full information about the project including progress of work at different time scale shall also be furnished.
List of works completed in the last seven financial years giving description of work, organization for whom executed, approximate value of contract at the time of award, date of award and date of scheduled completion of work. Date of actual start, actual completion and final value of contract should also be given.
Supportive documents/certificates from the organizations with whom they worked/are working as list of works completed and list of works on hand should be enclosed.
List of works on hand indicating description of work, contract value, and approximate value of balance work yet to be done and date of award.
Uploading of declaration regarding Employment/Partnership etc. of Retired Railway Employees as per GCC-2022 .
Uploading of Tender Forms shall embody the contents of the contract documents either directly or by reference and shall be as per specimen form, e-Tender Forms shall be issued free of cost to all tenderers.
A copy of certificate stating that they are not liable to be disqualified and all their statements/documents submitted along with bid are true and factual. Standard format of the certificate to be submitted by the bidder is enclosed as Annexure-V. In addition to Annexure-V, in case of other than Company/Proprietary firm. Annexure-V(A) shall also be submitted by the each member of a partnership firm/Joint Venture (JV)/ Hindu Undivided Family (HUF)/ Limited Liability Partnership (LLP) etc. as the case may be.Non submission of a copy of certificate by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested/digitally signed by which they/he are/is qualifying the Qualifying Criteria mentioned in the Tender Document. (As per Railway bord letter no.2022/CE-l/CT/GCC- 2022/Policy dt. 13.12.2022)
Declaration form regarding site etc.
Declaration regarding constitution of firm .
Engineers/Personnel.
Performa of Completion Certificate .
Shifting of existing Telephone Exchange and OFC equipment to new temporary construction office at PF-01 and Shifting of temporary Telephone Exchange and OFC equipment to new permanent building regarding Station redevelopment work at Gwalior station
JHS-N-W-23-26~NCR
JHS-N-W-23-26
Open
Works - General
9 Months
Jhansi, Uttar Pradesh
₹0
₹1.6 L
13 Apr 2026
20 Mar 2026
30 Mar 2026
108 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 74,96,522.41 | ||
| — | 1.00 | — | — | ||
| Supply of cable termination rack panel fitted with 12 no. of 32 way U link feed panel along with complete U links and mounting arrangement for isolation transformer. Suitable size copper strip to be provided for earthing on the rack.(Inspection Agency-Consignee). | — | — | — | 10,797.33 | |
| — | 7.00 | — | — | ||
| Supply of 19" 42U composite rack, covered with front transparent doors. The rack shall be complete with all fittings for housing 2 SDH(STM-1/4/16) equipments, 2 PDMUX along with PDP, DDF, Krone MDF for 100/200 pairs, cooling fans and other accessories like cable and connectors, runway ladders, locking arrangement, completely wired and equipped with anti surge protection through fast acting fuses and GD tubes for all channels, of reputed make President/Rittal or similar.(Inspection Agency-Consignee). | — | — | — | 2,63,708.69 | |
| — | 2.00 | — | — | ||
| Supply of managed STM-1, SDH (STM-1 Add/Drop MUX and upgradeable to STM-4) fully wired for 2 X 63 MB and equipped for 21 Els and minimum 4 port of 10/100 base T electrical interface (with LCAS and GFP), including power supply, order wire, Ethernet card, sub rack, inbuilt DDF, installation material and all other accessories and other common cards, manuals etc. as per TEC GR No. TEC/GR/TX/SDH - 004/04.Jan 2011 or with latest amendment. It shall be equipped with redundant power supply card. The contractor will supply all other accessories as mentioned in the above said TEC Specifications and system will have provision of different redundancy cards as per the TEC Specifications. Each node shall support mapping of management function to E1 signal. The equipment shall be compatible to the existing SDH system (if any) and NMS system (if any)in the section. This includes connecting all pig tails, optical patch cords etc.to the SDH equipment. Note: It shall be possible to increase capacity from 21E1 to 63 Els by adding / inserting tributary cards. This includes connecting all pig tails, optical patch cords etc. to the SDH equipment. This also includes connecting the SDH equipment with all cards to the 48V Bus including supply of wires and connectors. Termination of all E1s on DDF taking PVC cable over runway or a wall.(Inspection Agency-RDSO). | — | — | — | 4,73,260.5 | |
| — | 3.00 | — | — | ||
| Supply of 2 Mb Programmable Primary Digital drop insert multiplexer (PD MUX) as per RDSO Specs. IRS TC- 68/2012 Rev.0 (Amnd.1) or latest with conference facility and fully wired for 30 channel complete with power supply card, remote control, supervision facility and all other accessories, installation material, manuals etc. It should have facilities to accommodate data interface card in multi drop mode and should be able to support cards needed for video conferencing and ISDN. It shall support NMS installed at Test Room and may operate local/remote location of entire section. It also includes supply of all miscellaneous items which will be required for final testing and commissioning of system. The above MUX should be equipped with following cards : - (i) 2 wire/ 4 wire E&M VF circuit Card - minimum 04 no (ii) Subscriber loop circuit Card - minimum 02 no (iii) Exchange loop interface circuit Card - minimum 01 no (iv) Data Acquisition Card - minimum 01 no (v) GDT(G.703) Card - minimum 01 no (vi) Loop protection Card - minimum 1 no. (Inspection Agency-RITES/RDSO). | — | — | — | 5,78,480.04 | |
| — | 2.00 | — | — | ||
| Supply of 2 Mbps Line termination unit/LAN extender 48V DC/230 V AC operated, as per RDSO spec. No. RDSO/SPN/TC/82/2020 Rev. 2.0 or latest, along with suitable connectors to extend line data over copper cable of 0.5mm/0.63mm/0.9mm dia. or CAT 5/6 cables. Make Cygnus, Team engineer, Cisco.(Inspection Agency-Consignee). | — | — | — | 46,945.54 | |
| — | 3.00 | — | — | ||
| Supply of 2.048 Mbps, Managed SHDSL modems, as per RDSO spec. No. RDSO /SPN / TC / 80 /2020, Rev.2.0 or latest with suitable connector. Apair consists of V.35 andG.703 interfaces". Make- Cygnus, Cisco or superior.(Inspection Agency-Consignee). | — | — | — | 98,790.09 | |
| — | 6.00 | — | — | ||
| Supply of basic material to construct unit maintenance free earth as per RDSO Specs. No RDSO/SPN/197 Ver. 1.0 or latest to achieve a resistance less than 1 ohm. It consist of following: (a) Copper bonded steel electrode of minimum 3.0 m long, minimum 17.0mm dia with copper bonding thickness of minimum 250 microns and UL listed and marked = 1 no. (b) Earth enhancement material supplied in sealed bags of minimum 10 kg nos. =3 nos. (c) Copper strip of 150x25x6 mm, to terminate earth rod = 1 no. (d) Copper strip of 300x25x6 mm (MEEB) = 1 no. (e) Copper strip of 150x25x6mm (SEEB) = 1 no. (ii) Supply of 35 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting main earth electrode to MEEB in the equipment room in duplicate.(Inspection Agency-Consignee). | — | — | — | 1,08,255.12 | |
| — | 48.00 | — | — | ||
| Supply of maintenence free, VRLA battery/Cell 2V, 300 AH as per RDSO spec. IRS: S- 93/96(B) (Amnd. 1) or latest.(Inspection Agency-Consignee). | — | — | — | 2,51,673.12 | |
| — | 915.00 | — | — | ||
| Supply of CAT -6 UTP cable (one box of 305 Mtr). Make D-Link or similar.(Inspection Agency-Consignee). | — | — | — | 20,450.25 | |
| — | 20.00 | — | — | ||
| Supply of 24 fiber optical fiber cable straight joint enclosure (SJC) complete with all accessories along with enclosures with heat shrinkable splice protection sleeve as per RDSO spec. RDSO/SPN/TC/68/2014 Revision 1.0, Amndt. 1.0 or latest. Splice losses in no case should be more than 0.1 dB.(Inspection Agency-Consignee). | — | — | — | 1,10,109 | |
| — | 0.50 | — | — | ||
| Supply of Polythene insulated polythene sheathed jelly filled, armoured, telephone cable with poly-A1moisture barrier size: 10 pair, 0.5mm conductor diameter as per RDSO Specn. No. IRS TC 41/97 amnd. No.2 or latest.(Inspection Agency-Consignee). | — | — | — | 51,388.08 | |
| — | 4.00 | — | — | ||
| Supply of Fast Ethernet to SFP Media Converter 10/100/1000Mbps with 1.25G DDM 1310/1550nm SFP Module Transceivers SMSF Up to 20KM. Make-D-Link / Mrotek / TPLink/ Hanutech or superior. This also includes power adapter and necessary patch cords.(Inspection Agency- Consignee). | — | — | — | 27,972.32 | |
| — | 32.00 | — | — | ||
| Supply of SC to LC Single Mode Simplex Fibre Optic Patch Cable 10m length . Make :- Super shopper India/ superior.(Inspection Agency-Consignee). | — | — | — | 14,541.12 | |
| — | 114.00 | — | — | ||
| Supply of Armoured patch cord 10 Mtrs (Simplex) having SC to SC/SC to LC/LC to LC connector type as per site requirement. Make Anda Telecom or Superior.(Inspection Agency- Consignee). | — | — | — | 70,670.88 | |
| — | 20.00 | — | — | ||
| Supply of SC to SC Single Mode Simplex Fibre Optic Patch Cable 5m length . Make :- Super shopper India/ superior.(Inspection Agency-Consignee). | — | — | — | 10,988.4 | |
| — | 600.00 | — | — | ||
| Supply of power cable 3 core, 2.5 sq mm, multi strand (36/0.3 mm dia) cable as per IS 694:2010 reaffirmed 2015 or latest suitable for Railway electrification area, shall be of reputed make like Havells, Delton, LAPP, Finolex, or similar.(Inspection Agency-Consignee). | — | — | — | 69,108 | |
| — | 40.00 | — | — | ||
| Supply of krone Module 10 Pair Make: Krone or Similar.(Inspection Agency- Consignee). | — | — | — | 3,146 | |
| — | 2.00 | — | — | ||
| Supply of Online Power Back-up 10.0 KVA with 18 nos. 12V - 42AH (9072 VAH) Battery (Make: Microtek Model: Max+ 10 KVA)./Uniline/APC or Superior.(Inspection Agency- RITES/RDSO). | — | — | — | 5,04,988.3 | |
| — | 4.00 | — | — | ||
| Supply of 48 ports FXS media Gateway as per RB Doc No:2022/Tele/9(3)/4 dated 13.09.2022 or latest.(Inspection Agency-Consignee). | — | — | — | 3,84,412.32 | |
| — | 1.00 | — | — | ||
| Supply of 08 ports FXO Gateway as per RB Doc No:2022 / Tele / 9 (3) / 4dated 13.09.2022 or latest.(Inspection Agency-Consignee). | — | — | — | 39,702.36 | |
| — | 80.00 | — | — | ||
| Supply of OFC Joint box for termination of 2 Core/6 Core/12Core OFC. (Tiffin box type or similar).Make- Hanutech / JD or Superior.(Inspection Agency-Consignee). | — | — | — | 14,250.4 | |
| — | 1500.00 | — | — | ||
| Supply of Armoured Optical Fiber Cable, 6 Core, Single Mode, single fibre. Make-D- Link/Finolex/Paramount orsuperior make.(Inspection Agency-Consignee). | — | — | — | 36,030 | |
| — | 56.00 | — | — | ||
| Supply of PVC Plastic 6A MCB SP B Curve (White) Make-Havells no.DHMGBSPF006/Schneider/Legrand /L&T/Havells or similar.(Inspection Agency-Consignee). | — | — | — | 15,064 | |
| — | 80.00 | — | — | ||
| Supply of LPS 3.00 mm thick Rolled Copper Strip (LPS Pure Copper Earthing Strip25x3mm) of reputed branded make.(Inspection Agency-Consignee). | — | — | — | 97,920 | |
| — | 400.00 | — | — | ||
| Supply of 1 x 16 Sqmm (Red/Black/Green) multi strand pvc insulated copper flexible power wire, and test parameters as per RDSO Specn.No.IRS:S-76/89(Amnd.3) or latest. Colour of the wire which is required will be specified by the Engineer incharge.(Inspection Agency-RDSO). | — | — | — | 59,148 | |
| — | 100.00 | — | — | ||
| Supply of hot dip galvanised type cable tray with cover size 300mmX50mmX2mm. (Inspection Agency-Consignee). | — | — | — | 1,75,890 | |
| — | 2.00 | — | — | ||
| Supply and installation of wall mountable 19 '' 6 U rack complete with all accessories with Front Glass Door, Socket Power DB, Fan-FanTray, Cable Manager ,Hardware Packet , Earthing etc. with required accessories for mounting the equipment. Make: D-Link/CP-Plus or superior. (Inspection Agency-Consignee). | — | — | — | 6,752.02 | |
| — | 2.00 | — | — | ||
| Supply, installation and Fixing of 19 inch 9 U Racks wall mountable with Front Glass Door, Socket Power DB, Fan-FanTray, Cable Manager ,Hardware Packet , Earthing etc. with required accessories for mounting the equipment. Make: D-Link/CP-Plus or superior.(Inspection Agency- Consignee). | — | — | — | 9,003.7 | |
| — | 6.00 | — | — | ||
| Supply and installation of FMS (12 F-in & 12 F-out ) rack mountable single mode with Suitable type connector (Prefably SC type or as per site requirement) with splicing and termination of OFC cables with all accessories (Pig tail and other materials required for work to be supplied by contractor).Make D-link /Raycom/Tyco or superior.(Inspection Agency-Consignee). | — | — | — | 39,621.9 | |
| — | 16.00 | — | — | ||
| Supply and installation of FMS (24 F-in & out ) rack mountable single mode with Suitable type connector(SC Type or as per site requirement) with splicing and termination of OFC cables with all accessories (Pig tail and other materials required for work to be supplied by contractor ) Make D-link ,Raycom, Tyco or similar.(Inspection Agency-Consignee). | — | — | — | 1,39,343.68 | |
| — | 25.00 | — | — | ||
| Supply & fixing of I/O box-CAT-6.D-Link make or similar reputed make.(Inspection Agency-Consignee). | — | — | — | 6,998.5 | |
| — | 6.00 | — | — | ||
| Supply and installation of 150-150 pair IPM Depth MDF with 03 number 100 pair tag block with cable termination. The work is to executed as per the instruction of Railway Engineer. (Inspection Agency-Consignee). | — | — | — | 61,889.34 | |
| — | 24.00 | — | — | ||
| Supply and installation of Two pole MCB for electronic equipments as per ISI Standard with current rating 6A to 32A as per site requirement in suitable PVC/ Metallic Box.Make- Anchor/Schneider/Siemens or Superior.(Inspection Agency-Consignee). | — | — | — | 14,066.88 | |
| — | 3.00 | — | — | ||
| Supply, installation, testing and commissioning 4 port SIP PRI/EI gateway as per RB Doc No:2022/Tele/9(3)/4 dated13.09.2022 or latest. (Inspection Agency-RITES/RDSO). | — | — | — | 5,16,735.63 | |
| — | 1.00 | — | — | ||
| Supply and installation of Maintenance and administrative console for programming and maintenance of system and network, with latest configurations. Make - HP/DELL or Similar and as per RB Doc No:2022/Tele/9(3)/4 dated 13.09.2022 or latest.(Inspection Agency-Consignee). | — | — | — | 58,163.37 | |
| — | 1.00 | — | — | ||
| Supply, Installation, testing & Commissioning of Rack mountable set of two servers (work as fully hot standby) to work as IP-PBX. The server should be installed with Ubuntu Server LTS 22.04 and as per RB Doc No:2022/Tele/9(3)/4 dated 13.09.2022 or latest (Asterisk Guidelines attached in tender document) (Note: (a)Server should be COTS and not any proprietary server)(b) it support from 48 up to 500 subscriber).(Inspection Agency-Consignee). | — | — | — | 3,43,927.4 | |
| — | 8.00 | — | — | ||
| Supply and configuration of 24 Port L2 Smart Managed POE Switch 24 x Gigabit Copper PoE+ and 4 SFP port PoE. Make Dlink /Zyxel / Juniper or superior.(Inspection Agency- Consignee). | — | — | — | 3,90,966.48 | |
| — | 6.00 | — | — | ||
| Supply, installation and commissioning of Router [02 x 10/100/1000 LAN + 08 x02 Mbps [V.35] WAN + 08 x 02 Mbps [G.703] Ports; 300 kbps] as per RDSO specification no. RDSO/ SPN/TC/ 84/ 2008, Rev. 0.0 or latest. (Prior approval is requred by engineers representative before supply of material).(Inspection Agency-RITES/RDSO). | — | — | — | 15,01,110.42 | |
| — | 100.00 | — | — | ||
| Supply and fixing of PVC casing caping of size 1". Make: AKG/Finoflex/Paras/ Star sun light/Coppe-Rico or branded reputed make.(Inspection Agency-Consignee). | — | — | — | 2,222 | |
| — | 1.00 | — | — | ||
| Supply, Installation, testing and commissioning of 192 port IPDSLAM up to 256 ports along with rack and accessories as Telco cable of 5 mtr of ZYXEL or similar supply of 192 port splitter unit with spliter self covered rack mount and associated krone block with 19" rack mount along with accessories like connecting cable etc.(Inspection Agency-Consignee). | — | — | — | 2,99,544.3 | |
| — | 1.00 | — | — | ||
| Supply, Installation, testing and commissioning of automatic fire detection & alarm system as per RDSO Spec. No.RDSO/SPN/217/2021 ver. 3.0 or latest over Jhansi Division, as detailed in Annexure'A'. This Work includes complete installation & Commissioning of the system. All material required for complete installation and commissioning of the system will be supplied by the firm & all material to be procured from RDSO approved firms only. (Warranty period-24 months from the date of commissioning of that particular location).(Inspection Agency-RDSO). | — | — | — | 3,73,593.93 | |
| — | 2.00 | — | — | ||
| Supply, Transportation, Installation, Testing and Commissioning of 48 V/ 50 Amps SMPS based power plant (n+1) (2+1)configuration using 3 nos of 48 V/ 25 A module to charge the VRLA battery bank of 48 V /200 AH with lightening and surge protection as per specification No - RDSO/SPN/ TL /23/99 (Ver-4) (Amdt.1) or latest for telecom purpose. (Warranty Period : Upto 30 months from the date of delivery.)(Inspection Agency-RDSO/Consignee). | — | — | — | 1,64,020 | |
| — | 50.00 | — | — | ||
| Supply & installation of hot dip galvanised type ladder type cable tray of size 300mmX5OmmX2mm.(Inspection Agency-Consignee). | — | — | — | 30,873 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .