SPECIAL REPAIR OF INTERNAL SEWAGE LINE AT NEEL BHAVAN AND CERTAIN MINOR WORKS UNDER GE (WEST) FEROZEPUR CANTT

Amount

Demolition of cement concrete in ground floor not exceeding 15cm thickness (below or above ground level) and removing the demolished material and debris out side MD land complete all as specified and directed.

M&L PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in levelling to floor, filling of eaves gap, corner of interlocking tiles, filling sides of pressed steel chowkhats, etc complete all as specified and directed.

M&L 75mm thick, PCC 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection, shall be laid in 1:20 slope. The concrete shall be laid at a stretch not exceeding 3-meter in length. Joint gap between the adjoining slab, at corners and at junctions of wall shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen of grade 85/25 garde mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3-meter interval at corner and junction walls complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and rubbish off the primises complete all as specified and directed.

M&L non-skid coloured ceramic tiles of 7 mm to 8 mm thick, area of each tile exceeding 0.06 Sqm but not exceeding 0.11Sqm in floors set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match the colour over and including a screed layer of 15 mm thick in cement mortar 1:6, complete all as specified and directed.

M&L glazed ceramic coloured (colour & shade as approved) tile 350mmx250mm/450mmx350mm and 7mm thick on vertical surface such as skirting / dados set and jointed in neat cement slurry over & including 10 mm thick rendering in cement mortar 1:4 and pointed in white/ coloured cement with pigment to match the colour of tiles complete all as specified and directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as specified and directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each complete all as specified and directed.

S&F factory made mild steel, box type ventilator with side hung shuttes including projecting type hinges with steel handles and steel peg stay, complete without sash bars, dovtailed or welded complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm single piece extruded PVC profiles reinforced with 19 x 19mm MS square tube provided with EPDM rubber gasket weather seal through out the frame and the profile mitre cut at two corners and joined by inserting 2 nos 150mm long brackets of 15 x 15mm MS square tube inside 19mm x 19mm MS square tube suitably screwed complete all as specified and directed.

S&F 105mm x 60 mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

M&L PCC 1:3:6 type C1(using 20 mm graded aggregate) as in bed blocks for hold fast, filling of pressed steel chowkhat and all other similar works including necesssary formwork where ever required complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes of size 15mm x 15mm for top and bottom rails and 19mm x 19mm for stiles, MS frame covered with 5mm thick single piece extruded PVC profile 'C' channel having a 5mm thick PVC sheet strip of 20mm width struck inside with solvent cement, forming stiles, and 5mm thick single piece extruded PVC profile for top rail, lock rail & bottom rail on either side, and 10mm (5mm x 2) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail; panelling of 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with PVC sheet beading, and joined together with solvent cement adhesive etc all as per manufacturer's instructions and drawings as shown in SSR Part-I 2009 complete all as specified and directed.

S&F factory made 35 mm thick, 2nd class hard wood, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

M&L preparation of newly steel or iron surfaces of any description not otherwise described over 10 cm girth or width and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparing new wooden surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed.

S&F PTMT tower bolts, 200 mm long and fixed with steel screws complete complete all as specified and directed.

S&F PTMT butt hinges, 100 mm long and fixed with steel screws complete complete all as specified and directed.

S&F PTMT door handle, 125 mm long and fixed with steel screws complete complete all as specified and directed.

S&F 200mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm long extruded anodised Aluminium alloy handles, fabricated type complete all as specified and directed.

S&F 300mm long alluminium alloy anodised, sliding door bolt with hasp, staple (bolt type) and fix clips of sheet, cast of extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy all as specified and directed.

M&L 3.00 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 15mm bore bib taps, fancy type chromium plated, screwed for of iron pipe or for brass ferrule and fixed in repair complete all as specified and directed.

S&F 15mm bore stop valves bore fancy type, chromium plated, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions in repair complete all as specified and directed.

S&F 15mm bore pillar tap, fancy type cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, in repair complete all as specified and directed.

S&F chromium plated Soap dish Oval /square type as fixed in repairs complete all as specified and directed.

S&F Cabinet Mirror of size 400mm X 500mm complete all as specified and directed. Make : Cat Part No.554 of Prayag or techno-commercially equivalent in approved makes

S&F PVC connection 450mm long with 2 Nos brass check nuts suitable for 15mm bore of pipe with washer in repairs complete all as specified and directed.

S&F PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs complete all as specified and directed.

S&F vitreous China wash down water closet pan (Pedestal pattern) white including 'P' or 'S' trap and making good the disturbed surface to match with the existing complete all as specified and directed.

S&F Vitreous china white squatting pan Orrissa pattern of size 630mm X 450 mm with integral foot rests including necessary cement concrete and 100 mm bore cast iron ‘P’ trap with 550mm to 600mm long neck for connecting WC to branch piece with cement joints, fixed as in repair, complete all as specified and directed.

S&F wash hand basin, flat back 550mmX400mm vitreous China (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified and directed.

S&F 32mm waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F galvanised steel water tubes 15 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and directed.

S&F galvanised steel water tubes 20 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and directed.

Demolition of brick work including all quoins, arches, pillars etc. but excluding ashlar facings built in cement mortar complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per ser item No 40 here-in-before but using old bricks retrieved from dismantling under ser item no 39 here-in-before including cleaning and removal of mortar from old bricks etc.

M&L for half brick thick work with sub class "B" bricks built in cement mortar 1:4 complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc any description complete all as specified and directed.

M&L rendering 10 mm thick in cement mortar 1:6 on any face of brick walls or concrete surfaces, finished even and smooth with out using extra cement complete all as specified and directed.

M&L rendering 15 mm thick in cement mortar 1:4 on any face of brick walls or conrete surfaces, surfaces finished even and fair complete all as specified & directred.

M&L rendering 5mm thick in cement mortar 1:3 on ceiling, soffits of chajja or similar location any face of brick walls or conrete surfaces, surfaces finished even and smooth without using extra cement,etc complete all as specified & directred.

M&L preparation of new plastered surfaces wall and applying two coats of oil bound distember over a coat of primer and applying a coat of 1mm thick wall care putty complete all as specified and directed.

M&L preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

Taking down eaves gutters and rainwater pipes(any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for taking out and laying UG cable and getting out, excavated earth, forming bottom surfaces to required level complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 75 mm dia PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 75 mm dia PVC (SWR) vent cowl complete all as specified and directed.

S&F 110 mm dia PVC (SWR) vent cowl complete all as specified and directed.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement 75 mm dia outlet complete all as specified and directed.

S&F ball valves of 20 mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S&F 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

S&F 15 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

M&L white colour rotational molded triple layered polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I capacity of the tank 500 litre including GI tank nipple of size 20/15 mm dia including dismantling of old water tank complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete complete all as specified and directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and direced.

M&L110mm dia of bore concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested, in cement concrete 1:3:6 type C2 complete all as specified and directed.

Demolition of cement concrete in any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L 15mm thick cement mortar 1:3 with WPC on walls as well as on sunken floor portion finished even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid for separately.

M&L PCC 1:5:10 type E-2 (using 40 mm graded stone aggregate) as in filling under sunken portion complete all as specified and directed.

M&L 25mm tick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in floor finished even and rough to receive top layer complete all as specified and directed.

Supply only integral water proofing compound.

M&L for applying a layer of blown grade of industrial bitumen 85/25 @ 1.20 Kilogram per square metre including preparation of roof surfaces complete all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (weight not less than 150 gms/sqm) laid on primed surface by forced application including bitumen primer complete all as specified and directed.

Earth work in excavation for all kind of soil by mechanical means (Hydraulic excavator) in foundation trenches or drain (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out excavated soil and disposal of surplus excaveted soil within a lead of 50m complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and exceeding 1.5 metre but not exceeding 3 metre depth and not exceeding 10 Sqm on plan, for shafts, wells, cesspits, manholes, pier holes, etc and getting out, complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and exceeding 3 metre but not exceeding 4.5 metre depth and not exceeding 10 Sqm on plan, for laying of cable and getting out, complete all as specified and directed.

Demolition and breaking up salt glazed stoneware (SGSW) drain pipes set in cement mortar internal dia of pipe 250 mm complete all as specified and directed.

Demolition and breaking up salt glazed stoneware (SGSW) drain pipes set in cement mortar internal dia of pipe 150 mm complete all as specified and directed.

M&L cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid & tested for 250 mm bore pipe complete all as specified and directed.

M&L cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in bed to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested for 250 mm bore pipe complete all as specified and directed.

M&L cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid & tested for 150 mm bore pipe complete all as specified and directed.

M&L cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in bed to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested for 150 mm bore pipe complete all as specified and directed.

M&L 250 mm dia reinforced concrete pipes,class NP2 laid and jointed complete with collars in trenches as specified complete all as specified and directed.

All as per ser item No. 84 here-in-before but 150 mm bore pipe.

M&L cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) for 150 mm dia pipe in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified & directed.

M&L rendering, 15mm thick in cement mortar 1:4 on any face of brick walls or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L PCC 1:4:8, type D2 (using 40mm crushed stone agregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for cement concrete type B2 1:2:4 (using 40mm graded stone aggregate) in surface channels and drains complete all as specified and directed.

M&L providing cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, ier aps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), with plain fair faces,including chamfers, weatherings, throating etc. and setting in cement mortar 1:4 complete with joints to match complete all as specified and directed.

Dismantling of 100mm cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

S&F cast iron soil, waste and vent pipes of 100mm/75mm bore in any length with or without ears with cement joints fixed to wall complete all as specified and directed.

All as per ser item No. 92 here-in-before but fixing only. Note: erviceable pipe retrieved from ser item No. 91 here-in-before shall be reused.

S&F CI bends of 100 mm bore diminishing pieces or tapers including jointing with cement mortar 1:3 and making good complete all as specified and directed.

S&F 100mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F cast iron soil, waste and vent pipes of 75 mm bore in any length with or without ears with cement joints fixed to wall complete all as specified and directed.

All as per ser item No. 96 here-in-before but fixing only Note: Serviceable pipe retrieved from ser item No. 91 here-in-before shall be reused.

S&F CI bends of 75 mm bore diminishing pieces or tapers including jointing with cement mortar 1:3 and making good complete all as specified and directed.

S&F 75mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

M&L RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in Precast cover slab, shelves and similar articles and setting in mortar complete with joints to match complete all as specified and directed.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base etc. complete all as specified and directed.

M&L 100 mm thick PCC 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in floor topping complete complete all as specified and directed.

M&L cleaning of blockage of IWCs / EWC, bathroom / kitchen by cleaning the nahani traps / gully traps and CI / PVC pipe line upto the 1st Manhole. All the mud / sludge / Kitchen waste / plants roots to be cut/ removed and getting out by washing the traps, CI waste pipe throughly by opening the cleaning eyes lids properly. The sludge/ waste received during cleaning process to be removed at a distance not exceeding 100m from the building and Bleaching powder to be spread over waste and burred under the Soil / Earth complete all as specified and directed. Note: Earth work shall be deemed to be included in the quoted rate.

Cleaning and desludging / de-watering of septic tanks /Manholes and soakage well of any depth by using honey sucker followed by mechanical roding followed by hydraulic jet pressure machine etc as required, with the entire satisfaction of Engr -in- charge and re-fixing the manholes cover to its original position complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

Demolition of stone slabs and tiles laid bedded pointed in mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

M&L 100mm thick hardcore of broken stones gauge exceeding 63mm but not exceeding 100mm, deposited, spread and levelled in layers not exceeding 15 cm thick including watered and rammed to a true surface complete all as specified and directed.

M&L sand cushioning in trenches for underground cables complete all as specified and directed.

M&L 100mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base etc. complete all as specified and directed.

M&L machine cut Kota stone slab flooring 20-25mm thick over 20 mm cement screed base cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing polishing and rounded or chamfered for nosing complete all as per specified and directed.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 15mm thick rendering in cement mortar 1:4 and jointed as per ser item No 111 here-in-before.

S&F 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with J- type or L- type hook bolts complete all as specified and directed.

S&F Mild Steel work as in roof truss (framed) trussed, purlins crane gantries, rails and fastenings and heavy bracket framing (Beam tee, angle channel or flat sections) inclusing distance pieces, cleats etc Fe 410-W (Gde E-250) quality B complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/ loose soil complete all as specified and directed.

Excavation in post holes (or similar holes) Each not exceeding 0.50cum, getting out in hard/dense soil, returning, filling, in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50 m and making good surface in soft/loose soil complete all as specified and directed.

M&L cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete for pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed.

S&F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated), Fe- 290 (Gde E- 165) complete all as specified and directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, Fe- 290 (Gde E- 165) complete all as specified and directed.

S&F Pre-painted galvalume alumimium zinc coating GI based corrugated/crimped steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa in roof covering, fixed with self tapping screws complete all specified and directed.

M&L hardcore of broken bricks of gauge not exceeding 63mm, deposited spread and leveled in layers not exceeding 15cm thick watered and rammed to a true surface below interlocking tiles and in sunken floor complete all as specified and directed.

M&L precast machine pressed cement concrete interlocking paver blocks of any shape and size confirming to IS 15658-2006 of 60 mm thick M-35 grade, with grey cement and pigment laid dry over a layer of 25 mm thick sand cushioning complete all as specified and directed.

S&F factory made box type side hung steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to Each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type side hung steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to Each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

M&L galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

M&L cutting holes in brick wall exc half bricks but not exc one brick in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4, type B-1 as required complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls etc., and applying three coats of white wash complete all as specified and directed.

M&L providing 40 mm thick pre-cast cement concrete louvers or RCC Jali made out of cement concrete 1:2:4 type B-0, (using 12.5 mm graded stone aggregate) and set in cement mortar 1:4 including all mouldings and dismentling etc. complete all as specified and directed.

M&L preparation of newely plastered surfaces wall and applying two coats of oil bound distember complete all as specified and directed.

M&L PCC 1:3:6 type C2 (using 40 mm graded stone aggregatea) as in foundations, filling and mass-concrete complete all as specified and directed.

S&F rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary & counter sunk) forming holes, with riveted, bolted or welded attachment GDE Fe410-0 complete all as specified and directed.

S&F pre-painted galvalume Aluminium Zinc coating GI based plain steel sheet 0.50mm thick in ridges of an colour having tesile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F mild steel work as in posts or struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc) including all necessary bolting or riveting etc and similar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

S&F 1000 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings, complete all as specified and directed.

M&L wash hand basin, flat back 550mmx400mm vitreous china (white) including PTMT waste fittings of 32mm bore size, waste pipe PVC of 32mm bore, PVC connector 450mm long with angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing specification complete all as specified and directed.

S&F grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40 gms) complete all as specified and directed.

S&F 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and directed.

S&F Stop/Angle valve 15mm bore fancy type chromium plated, screwed down high pressure, with high pressure crutch or butterfly handle, screwed both ends for iron pipeor union complete all as specified and directed.

S&F 600mm long towel rail of PTMT fixed to wall with steel screws and PVC rawl plug complete all as specified and directed.

S&F cast iron Nahani trap 100 mm dia with gratting including jointing to waste pipe fixed with concrete cement in 1:2:4 type B1 (using 20 mm graded stone aggregate) etc complete all as specified and directed.

S&F Cast iron floor trap of 100 mm dia, with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 complete all as specified and directed.

S&F High density polythelne pipe of 50 mm bore dia (HDPE) of pressure rating 6 kg/cm2 fixed complete to walls, ceilings or in floors etc complete all as specified and directed.

M&L galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.

M&L galvanised iron steel water tubing, 20mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.

M&L glazed ceramic coloured (colour & shade as approved) tiles non skid of size 400mmx400mm and 7mm thick as in floor set andjointed in neat cement slurry over and including 15mm thick screed in cement mortar 1:6 complete all as specified and directed.

All as per Item No-146 here-in-before but as on vertical surfaces such as skirting/dado over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed.

M&L glazed ceramic coloured (colour & shade as approved) tiles of size 300mmx200mm and 7mm thick on vertical surface set and jointed in neat cement slurry over 10mm thick rendering in cement mortar 1:4 and pointed in white cement with pigment to match the colour of tile complete all as specified and directed

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified and directed.

M&L RCC 1:1.5:3, nominal mix using (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 10 mm thick screed bed in cement mortar 1:4 complete including moulding at corners and polishing type complete all as specified and directed.

M&L 150m dia SGSW drain pipes laid in trenches and jointed complete all as specified and directed

M&L PCC 1:3:6 type D-2 as in concrete bed to drain pipes including packing under and haunching against the sides of pipes afrter they are laid and tested in 150 mm bore pipe complete all as specified and directed

M&L for providing precast cement concrete 1:2:4 type B-1, as in manhole cover including necessary form work excluding reinforcement and set and jointed in cement mortar 1:4 complete all as specified and directed.

HARBHAJAN SINGH KHARBANDA

B.L. Chaudhri and Co.