REPAIR TO PLASTERING TILING PLUMBING AND OTHER COMPREHENSIVE MAINTENANCE TO CERTAIN UNITS AND VIP AREA UNDER AGE B R I OF GE BENGDUBI MIL STN

Amount

SCHEDULE 'A'

Taking down cement plaster any description on brick or stone walls, etc. Incl raking out joints, hacking for key, scrubbing down with water, etc complete as specified and directed.

M&L rendering 15 mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces mixed with water proofing compound in top layer of 5mm thick as per manufacturer’s instructions and finishing the surfaces fair and even without using extra cement complete as specified and directed. (Note : WPC measured and paid separately as ‘Supply only’ against appropriate item of this schedule)

Supply only liquid water proofing compound as specified and as directed.

M&L rendering 15mm thick on other than fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete as specified and directed.

M&L for rendering 5 mm thick on ceiling in CM 1:3 finished even and smooth without using extra cement complete complete as specified and directed.

M&L preparation of new plastered surfaces of wall, etc and applying two coat of cement base paint complete as specified and directed.

M&L for preparing new plastered surface of walls and applying two coat of oil bound distemper white or any tint over 1 mm thick wall care putty etc complete as specified and directed.

M&L for preparing new plastered surface on ceiling and applying two coat of oil bound distemper white or any tint over 1mm thick wall care putty etc complete as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile and including 20mm thick screed bed or bedding layer in cement mortar (1:6) in floor etc complete all as specified and as directed.

M&L for Non-skid coloured ceramic tiles 7 to 8mm thick(square/rectangular)area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile and including 20mm thick screed bed or bedding layer in cement mortar (1:6) in floor etc complete all as specified and as directed.

M&L for light shade Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 20mm thick screed bed or bedding layer in cement mortar (1:6) in floor etc complete all as specified and as directed.

M & L glazed ceramic coloured tiles (450 X 300 X 7mm) thick as in vertical surfaces set & jointed in neat cement slurry & pointed in white or coloured cement to match the existing surface complete as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. Laid, bedded and pointed in any mortar complete as specified and directed.

M&L for Granite (of any type) tiles 16mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing and including 20mm thick screed bed or bedding layer in cement mortar (1:6) in floor etc complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 15-20 mm thick over 20 mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as specified and directed.

M&L for Machine cut kota stone slab flooring 15-20 mm thick as in skirting, riser of steps, dado and pillar over 10 mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets and frame work complete all as specified and directed.

Providing and fixing PVC FALSE CEILING, consisting of 600x600mm, 5mm (+0.25) thick plain ambossed PVC sheet of 600Kg/Cbm Density manufactured by ISO 9001-2008, certified company, used as panel insert in a frame work made using anodised aluminium T- section of sizes 1"x1" (25x25mm, 19 gauge or 1mm thick) in square pattern of grid sizes of 2'x2'(600x600mm). the aluminium frame work is supported from the ceiling with the help of "J" hook and GI wire/6mm MS rods of require sizes to maintain proper level etc. The aluminium framework is supported on side wall with the use of aluminium L-section of size 1"x1"(25x25mm) angles etc. complete as specified by manufacturer & drawing and directed by Engr-in- Charge.

Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2ndclass soft wood fillets, or metal framework and reinforced with G.I. wire mesh (Fillets, metal frame work andG.I. wire mesh paid separately).

Gl frame work for seamlessceiling comprising of Glperimeter channnel 0.55 mm thick with two unequal flangesof 20 and 30 mm and web of27 mm fixed to surroundingwall using nylon sleeves andscrews at 450 mm centre tocentre/intermediate channel0.9 mm thick having two equalflanges of 15 mm each and webof 45 mm suspended fromsoffit at approx 900 mm centreto centre with Gl cleat andsteel expansion fasteners withand including ceiling section(not exc 1.2 m length) of 0.55mm thickness having kurled web of 50 mm and flange of26 mm each with lips of 10.5mm fixed to the intermediate channel with connecting clipsacross the intermediatechannel at 457 mm centre to centre complete all as specified and directed.

S& F 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified as directed.

S& F Anodised aluminium snap grid frame 605 x 605mm for false ceiling and Hangers 6 mm dia. G.I. (upto1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm longand expansion hold fasteners12.5mm dia. 40mm long complete all as specified all as specified complete all as specified as directed.

M&L for applying two coats of synthetic enamel paint on false ceiling over one coat of pink primer preparation of new wooden surfaces of any description over to 10 cm width or girth and complete all as specified and directed.

Taking down steel tubing and connection 15mm bore complete all as specified and directed.

Taking down steel tubing and connection 20mm bore complete all as specified and directed.

S&F G I tubing medium grade, galvanised with all fittings and fixed complete to wall and ceiling or laid in floors bore of tube 15 mm complete all as specified and directed.

S&F G I tubing medium grade, galvanised with all fittings and fixed complete to wall and ceiling or laid in floors bore of tube 20 mm complete all as specified and directed.

Supply and fix in repairs PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Supply and fix in repairs PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Supply and fix in repairs PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fix to wall complete all as specified and directed.

S & F in repair for stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110 mm bore of pipe complete all as specified and directed.

S&F PVC (SWR) vent Cowl for 110 mm bore pipe

S&F PVC (SWR) Bends (any radius ), diminishing pieces or tapers, bore of pipe 75mm, complete all as specified and directed.

S&F PVC (SWR) Bends (any radius ), diminishing pieces or tapers, bore of pipe 110mm, complete all as specified and directed.

S&F PVC (SWR) junction single, Single T equal or unequal for 110 mm bore of pipe complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with grating 75mm including jointing to wast pipe fixed in cement concrete type B1 (1:2:4) ,in repairs and including waterleak proof treatment complete all as specified and directed.

Dismantling PVC water tanks exc. 250 litres but n. exc. 500 ltrs capacity complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks of capacity 500 litres (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I.

S&F in repair 20 mm bore, gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F in repair ball brass valve, high pressure, with ploythene float and flynut complete, screwed for iron pipe or brass ferrule 20 mm bore complete all as specified and directed.

S & F in repair Bib tap 15 mm, fancy type, long swan neck, CP with crutch or butterfly handle screwed down srewed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair Brass CP mixer for mixing hot & cold water screwed down for 15 mm bore pipe complete all as specified and directed.

S&F in repair CP angle stop cock 15 mm bore fancy type cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S & F in repairs CP brass shower rose 125 size dia complete all as specified and directed.

S&F towel rail 600 mm long of brass CP fancy type.(Make-JAQUAR,Cat. No -1111N) complete all as specified and directed.

S&F toilet paper holder premium approved quality .(Make- JAQUAR, Cat No-con1151N) complete all as specified and directed.

S&F in repair soap dish of best quality complete all as specified (MAKE-JAQUAR, CAT NO-CON 1131N) complete all as specified and directed.

S & F in repair Vitreous china wash down water closet European type (pedestal pattern) (excluding flushing cistern and flush pipe) including connection to outgoing pipe and seat cover and flushing pipe all as specified and directed. (Make: Hindware or Cera)

S & F in repairs 10 lits capacity PVC flushing cistern low level, white, with inlet, ball valve, float and handle and flush pipe including brackets etc complete all as specified and directed.

S&F in repair vitreous china wash hand basin in repair oval special type 510x410mm including CP fancy type 15 mm pillar taps including 32mm dia PVC waste pipe, and 32 mm dia brass CP waste coupling complete all as specified. Make-Hindware, CERA

S&F in repair PVC Connections 15 mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F Soap dish brass chromium plated fixed with chromium plated brass screws complete all as specified and as directed.

S&F looking mirror 450X600mm with plywood backing and aluminium frame complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail, 20 mm dia, D type, 60cm long between flanges complete all as specified and directed.

Demolition of cement concrete unreinforced in Ground floor & paving n.exc 15cm thickness and removal of debris from site complete all as specified and directed.

M&L for PCC 100mm thick 1:4:8 type D 2 using 40mm graded stone aggts as in floor,path dtc finishing the surface even and smooth without using extra cement complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Taking down unservicable steel gate/shutter of any description of size exc 9 sqm but n exc12 sqm each including taking out of unservicable parts/portion by cutting and replacing with new one as per the existing size and specification and refixing in the same opening by maintaining proper alignment including repairing defective portion of gate/shutter, steel structurre to match with exsiting structure including necessory cutting, drilling, welding and reveting etc, greasing, oiling to movable parts including all necessory fittings and appying one coat of synthetic enamel paint over a coat of pink primer to new portion/structure complete all as specified and directed.

S & f framed work as in Roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channelor flat sections) including distance pieces, cleats etc complete contining to Fe 410-W(Gde-E-250)quality A, complete all as specified and directed.

M&L for preparation of new painted steel surfaces of any description n.exc 10cm width or girth and applying two coat of synthetic enamel paint any tint over one coat of primer complete all as specified and directed.

M&L for painting to steel surfaces of any description over to 10 cm width or girth not other wise described. Painting two coats of synthetic enamel paint over one coat of Red oxide primer incl preparation of new steel surfaces complete all as specified and directed.

S&F for 1.00 mm thick Steel rolling shutters, with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer with Safety lever locks mild steel with 4 levers for rolling shutters eerected in position as indicated, complete; push pull or manual type complete all as specified and directed.

Dismantling plain, Trapezoidal or corrugated PPGI/steel sheeting, any gauge, thickness in roof coverings incl ridges complete all as specified and directed.

S & F 0.50 mm thick Pre painted galvalume aluminium Zinc coating GI based TRAPEZOIDAL steel sheet with pitch 200 mm & profile 30 mm of any colour having tensile strength of 550 Mpa as in roof covering / Cladding to wall fixed with self tapping screws complete all as specified and directed.

S&F Pre- painted galvaLume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

Demolition of brick work built in cement mortar all as specified and directed.

M&L for old size fly ash brick work with sub class 'B' bricks, straight for curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed.

M&L for old size fly ash brick work with sub class 'B' bricks, straight for curved on plan to any built in CM 1:4 complete all as specified and directed.

S&F Powder coated Anodised aluminum frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F for Powder coating anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed.

S&F for Powder coating anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sections weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, anodised aluminum snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1 no.) hinges type B-21 100 mm long (2 no) suitable handle (1 no) etc complete all as specified and directed.

S&F Powder coated for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminum snap beading, screws etc complete all as specified and directed.

M&L any size mesh aluminium anodised grills of approved designs complete all as specified and directed.

S/F mortice lock vertical type barss 100mm size 4 levers complete all as specified and directed.

S&F double action floor spring hydrualically regulated made up of minimum 12.5 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and directed.

M& L for 5.5 mm thick sheet glass ordinary quality frosted on one side including glazing clips, rubber packing etc exc. 0.5 sqm in each pane complete all as specified and directed.

S&F stainless steel decorative curtain rod of 25mm bore complete all as specified and directed.

S&F finial fancy type for curtain rod in pair etc complete all as specified and as directed.

S&F bracket for curtain rod in pair etc complete all as specified and as directed.

S&F in repairs table top vitreous china wash hand basin flat black basin white/ coloured, size 610 x560mm including CP waste coupling but excluding taps, waste chain & plug complete all as specified and directed.

Demilition of old existing unserviceable EWC seat and S&F western floor mounted one piece water closet ceramic western toilet/commode/European commode square with soft close seat cover white including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe etc complete all as specified and as directed.(Make- JAQUAR, Cat No-AIS-WHT-101851S220SPPSM)

S&F in repairs bottle trap of having min water seal of 25mm (Minimum weight 32mm-260gms/40mm-270gms) complete all as specified and directed.

S&F in repairs CP central basin mixer with U shaped round casted sprout with 450mm long baried houses complete all as specified and directed.

S&F jet spray with 01 mtr PVC tube (Stainless steel) complete all as specified and directed.

S&F in repairs two way angle cock 15mm bore cast copper fancy CP alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs glass shelf assembly consisting of 5.5mm thick sheet glass with CP brackets and CP frame size 600mm long complete all as specified and directed.

S&F in repairs PVC board designer Eaves 9 mm thick elegant appearance 200mm of width complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in sec in any position complete all as specified and directed.

(Note : The Scope of Work contained in 'Sch of Credit' amounting to Rs. 3,43,434.00 (refer Tender Srl Page No 34(R)). The Quoted sum shall be arrived at after deducting the amount of “Sch of Credit” from the total amount of the ‘BoQ’

M/S BOSE ENTERPRISE

M/S P. RAI CHOUDHURY AND CO.

MUKHERJEE ENTERPRISE

M/S BISWAJIT BHATTACHARJEE

M/S DUTTA CONSTRUCTION CO

PRADIP KUMAR BOSE