ADDN ALTN IMPROVEMENT TO SMQS OMQS SNCOS AND AIRMEN BILLETS AT AF STN MOHANBARI

Amount

B/R PORTION

Taking down chowkats or frames n.exc 1.5 sqm each with shutters (without taking off shutters from the frame complete all as specified and as directed.

Taking down chowkats or frames exc 1.5 sqm but not exc 4 sqm each with shutters (without taking off shutters from the frames complete all as specified and as directed.

Taking down shutter of any description exc 1 sqm and not exc 2 sqm each and refixing in the same opening of shutters complete all as specified and as directed. (Note : After easing and adjusting for smooth movement)

M & L for Taking down of cement plaster of any description including racking out joints for key scrubing with water etc complete all as specified and as directed.

Taking down plastering on lathing (other than wire netting), without removing lathing, but in cement lime or cement mortar(one side only measured in cases where both sides are plastered complete all as specified and as directed.

Taking up or down GI tubing 15mm bore including cleaning for refixing complete all as specified and directed by Engr-in-Charge.

Taking up or down GI tubing 20mm bore including cleaning for refixing complete all as specified and directed by Engr-in-Charge.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets removing rubbish obtained from dismantling from work site out side MD land at any distance complete all as specified and as directed.

Dismantling plain, corrugated or semi-corrugated AC sheets roof coverings complete all as specified.

Dismantling plain, corrugated or semi-corrugated CGI sheets roof coverings complete all as specified.

Dismantling wrought iron or mild steel work of any description and in any position complete all as directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises (out side MOD land) complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n exc 15 cm thickness (below or above ground level) including removal of debries out side defence land complete all as specified and directed.

Demolition Brickwork or stone/ boulder masonry, built in cement/lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Dismantling unframed work timber scantlings 40 sq. cm and over in section, in any position including removing of unserviceable material from work site complete all specified and as directed.

Taking down roof trusses, coupled rafters or trussed beams etc for renewal of any defective members (timber/steel renewed to be measured separately) above 4 mtr to upto 8.0 mtr and reassembling and Housing and fixing trusses etc. after repairs including tightening up wedges, cotters bolts etc. complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard/dense soil complete all as specified and directed.

M & L for Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

M & L for Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.

M & L for Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M & L for 75 mm thick hardcore of broken stone or boulder of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for providing and injecting chemical emulsion for Post constructional Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia hole with cement mortar 1:2 and repair to match with the existing floor complete all as specified and directed.

M & L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M & L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

"Supply only" integral WPC complete all as specified and directed.

M & L for Cement concrete (1:4:8) D2 using 40mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed.

BLANK

M & L for Providing cement concrete Type B1 (1:2:4) using 20mm graded aggregates in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M & L for Providing precast RCC in type B1 (1:2:4) using 20mm graded aggregates in landing, cover slab etc including necessary form work complete all as specified and directed. Note:- Reinforcement shall be measured and paid saperately.

M & L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. complete all as specified and directed.

M & L for brick work inburnt brick with sub-class ‘B' old size bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:6). All as specified and as directed.

BLANK

S & F 2nd class HW Plain, solid, straight chowkats second class hard wood and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S & F 2nd class Hard Wood clean sawn in fixed as timber scantling complete all as specified and directed.

S & F 35mm thick factory made Glazed and skeleton shutters, second class hard wood open rebated and prepared to receive lass,gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. Note:- Wire mesh/ glass shall be measured and paid separately.

S & F 35mm thick framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M & L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

M & L Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sh eet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and directed.

S & F 140mm overall length of cover plate floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F 100mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F 125mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S & F 150mm long Aluminium handles, cast type, anodised complete all as specified and directed.

S & F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel wire staples complete all as specified and directed.

BLANK

S & F rolled mild steelFe-410- W(GdeE-250) quality A for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. all as specifies and as directed.

S & F MS works as in wind tie for roof flat iron fillet for securing wire mesh etc and similar works conforming to Fe 290-0 Gde E-165 including drilling holes as required all as specified and directed.

S & F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S & F Steel reinforcement Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S & F false ceiling grid 600 x 600mm powder coated/ polyster paint factory made wall angle, 24x24mm, fixed to surrounding wall using nylon, Sleeves and screws at 450 mm centre to centre main T 24x33 mm, 24x48mm cross section and suspending from roof with 6mm GI wire 900mm centre to centre approximate with GI cleat and steel expansion fastened with and including ceiling section (not exc 1.2 m length) and ceiling tiles of size 600x600x12 mm made up of mineral fibre, triangle pattern and approved model complete all as specified and directed.

BLANK

BLANK

Supply and fix for powder coated aluminium sliding windows three track with three sliding shutters (two number glass shutter and one number wire mesh shutter) with extrusions aluminium of following sections including jointing cleats, glazing clips, rubbr packaging, snap beading and other necessary builders hardware as required complete all as specified and directed. (A) FRAME:-(i) Top and side member for three track frame of size 92mmx38mmx1.2mm (Weight not less than 1.2 Kg) (ii) Botton rail for three track frame of size 92mmx38mmx1.2mm (Weight not less than 1.2 Kg) (B) SHUTTER:-(i) Top and bottom rail of sliding shutter of size 40 mm x 18 mm x 1.5 mm (weight 0.547 Kg/ mtr) (ii) Side of sliding shutter with handle and self locking arrangement, section of size 40 mm x 18 mm x 1.5 mm (weight 0.547kg/ mtr) (C) Sliding shutter to be provided with 5.0 mm thick sheet glass complete all as specified and directed. (D) Supply & Fix for 6.5 mm thick powder coated ) Aluminum Deco grill DG -104 with mill finished fixing on wall/wooden chowkhat/ aluminium frame with suitable size of aluminium 'U' channel and steel chromium plated, screw with rawel plug complete all as specified and directed with following details:- (i) Aperture size of aluminium grill 67 mm x 84 mm. (ii) Cord dimension 7 mm x 5.8 mm. (iii) Plate thickness 2 mm. (E) Supply & Fix for Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with galvanized wire staples/ clip/aluminium flat with and including third shutter along with special auto lock dry set complete all as specified and as directed.

Material and labour for powder coated aluminium ventilator frame with frame of section 100mm x 44mm of thickness 1.6 mm, shutters of section 32mm x 15mm (with and including half portion fixed glazed shutter and rest half portion louvers with gauzed shutter) including stainless steel wire mesh, rubber gasket for securing the glass, 5.5 mm thick figured glass, aluminium grill and necessary aluminium mongeries and handles including necessary locking arrangement complete all as specified and as directed.

BLANK

S & F of Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of camouflage pattern having tensile strength of 550 Mpa as in roof covering/ridge/ cladding to wall, fixed with self tapping screw (Heavy duty) with in built washers and neoprene & EDPM washers, in roofs, walls etc complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of camouflage pattern having tensile strength of 550 Mpa as in roof covering/cladding to wall, as in valley gutter, ridge etc fixed with self tapping screws as specified etc complete all as specified and directed.

S& F GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc in walls, ceilings, stanchions, beams etc including all laps, cutting and waste complete all as specified and directed.

M & L for 25 mm thick cement concrete type B0 1:2:4 using 12.5 mm graded aggregate as a sub base for levelling complete all as specified and directed.

Material and labour for 75 mm thick, PCC (1:3:6) type C-1 using 20 mm graded stone aggregates as in plinth protection for finish even and smooth without using extra cement complete all as specified.

M & L for 100 mm thick cement concrete type D2 1:4:8 using 40mm graded aggregate as a sub base for levelling complete all as specified and directed.

M & L for Coloured Glazed ceramic tiles 350x 250x 7mm/ 450X 350X 7mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 10 mm thick rendering in cement morter (1:3) on brick wall complete all as specified and directed.

Material and labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screeding in CM 1:6 complete all as specified and directed.

M & L for Factory made colour Chequered cement concrete tile with pigment 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigments in floors over 15mm thick screed bed in CM (1:4)complete all as specified and directed.

M&L for Green Marble 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed.

M & L for machine cut kota stone slab flooring 18 to 20 mm thick. over cement screed base 20mm thick in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Taking down of existing roof treatment from roof and terrance, roughening surface of old concrete roof by picking, sweeping clean and washing down with water to remove dust, etc and applying roof treatment with the following specification:- (a) Applying cement slurry over concrete surfaces @3kg/sqm. (b) Rendering 15mm thick in cement mortar (1:4) mixed with water proofing compound as per manufacture's instruction on cleaned concrete surfaces of roof and finishing the surfaces fair and even including curing the plastered surfaces for 7 days by ponding of water over the roof, (leveling course). (c) Applying evenly one coat of cold bituminous primer conforming to [email protected] liter per square metre on the cleaned plastered surfaces (d) Applying evernly one coat of blown hot bitumen of grade 85/25@ 1.20 Kg per square metre on primed surfaces. (e) Applying a layer of APP based polymeric membrane, 3mm thick (minimum) weighing 3.50 Kg per square metre reinforces) with polyster non woven fabric wighing not less than 160 gms per square metre by torch application. The overlap shall be not less than 100mm on transverese direction and 75mm on longitudinal direction and sealing overlaps. (f) Applying evenly one coat of aluminium paint @ 0.10 litre per square metre over the APP based polymeric membrane. (g) Water Proofing compound shall be measured and paid separately.

M & L for rendering 15mm thick in cement mortar (1:6) on brick or concrete surface finished even and smooth without using extra cement complete all as specified and directed

"Supply only" integral water proofing compound (ISI marked) complete all as specified and directed.

M&L for 15mm thick rendering in CM (1:4) in two layers (10+5) mixed with water proofing compound @ 3% by weight of cement in top 5mm thick finishing the surfaces with fair and even without using extra cement complete all as specified and directed. Note:- Water proofing compound shall be measured and paid saperately.

M & L for rendering 20 (15+5) mm thick on the other side of lathing plastering in cement mortar 1:4 with complete framing with shuttering as one side fair and plastering with other side as fair finish form other side complete all as specified and directed.

M&L Preparation of new plastered wall surfaces and applying two coats of exterior emulsion weather proof paint over a coat of primer complete all as specified and directed.

M&L for Preparing newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant priming, on plastered surfaces, complete all as specified and as directed.

M&L Preparation of new plastered wall surfaces and applying two coats of cement base paint over a coat of chalk whiting, on plastered surfaces upto clear undulence including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces complete all as specified and directed.

M & L for complete removal of old existing surface and preparation of surface with two coats of oil bound distemper over a coat of chalk whitening primer on walls complete all as specified and directed.

M & L for complete removal of old existing surface and preparation of surface with two coats of cement base paint over a coat of chalk whitening primer on walls complete all as specified and directed.

BLANK

M & L for Sanding newly tarred or painted surfaces with clean sharp sand complete all as specified and directed.

M&L for preparation of new surfaces steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of red oxide primer all as specified and directed by Eng-in-charge.

M&L for preparation of new surfaces wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of pink primer all as specified and directed by Eng-in-charge.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) all as specified and directed by Eng-in-charge.

M&L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint all as specified and directed by Eng-in-charge.

Supply and fixing rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 500 ltr capacity hoisted and fixed in position with air pipe all as specified in SSR Pt - I including dismantling old one complete. All as specified and as directed.

Cleaning of water tank, capacity 250 to 500 ltrs with all scales and dirts from inside of tank and mouth of inlet/outlet using bleaching powder and washed with water including disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required and reconnecting / re-fixing in position by supplying and fixing of any assesories as per site requirement and clear marking of date with white paint complete all as specified and as directed.

S&F 20 mm bore ball brass valve, high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S & F in repair steel tubing of 15 mm dia medium grade including bends and cutting all specified and directed.

S & F in repair steel tubing of 20 mm dia medium grade including bends and cutting all specified and directed.

Supply & Fixing in repair Stop valves, fancy type, 15 mm dia, cast copper alloy, fancy type screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

BLANK

S & F aluminium anodised Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

BLANK

S&F PVC connection pipe 15 mm dia and 600mm long with PTMT nuts complete all as specified and directed.

S&F in repair 20 mm bore gun metal, glove or gate valves ISI marked with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F in repair 15 mm bore gun metal, glove or gate valves ISI marked with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S & F in repair 15 mm Bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, fancy type screwed for iron pipe complete all as specified and directed.

S & F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repair vitreous china squatting pan of orissa pattern long pan size 580mm x 440mm white including making good to existing flooring complete all as specified and as directed

S&F in repair 10 Ltrs capacity PVC flushing cistern, valveless, syphonic action type, low level white with inlet, ball valve, float and handle complete including brackets and connection to pipe complete all as spcified and as directed.

S&F in repair vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum),with grating and union for discharge pipe complete all as specified and as directed.

Supply & Fixing Vitreous china wash hand basin size 550x400mm (flat back or angle back type) including 32mm dia brass chromium plated waste fitting a pair if cast iron bracket duly painted /erecting stand including PVC conncetion of 450 mm length cutting and pinning in ends making good disturbed surfaces in CM 1:3 including taking down unserviceable wash hand basin and connected items of any description, complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches complete all as specified and directed.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed in wall or trenches complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S & F PVC (SWR) 75mm floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S & F in repair Swivel shower of PTMT 15mm bore of any colour including Shower arm 195mm long with bend of 45 degree with flange of PTMT any colour.(Minimum weight 40gms complete all as specified and directed.

E/M PORTION

Taking down carefully copper/aluminum point wiring (light ,fan, bell and socket etc) complete including fittings such as switches, ceiling roses, pendent, regulators, sockets etc removing materials for taking credit and making good including matching to the existing colour to the disturbed surface wall/ floors etc complete all as specified and directed.

Taking down carefully ceiling/exhaust fans, sealing cable ends,dismantelling blades removing fan and blades for taking to store and refixing back to its original position and making good including matching to the existing colour to the disturbed surface wall/ floors etc complete all as specified and directed by Engr-in-charge.

Material and labour for one light / fan / bell point controlled by one number one way switch with 1.5 sqmm cable PVC insulated unsheathed type, copper conductor, multistranded cable (FRLS type), 1100 Volts grade (red colour cable for phase and black colour cable for neutral) including 1.5 sqmm copper conductor, multistranded cable (FRLS type) 1100 Volts grade unsheathed PVC insulated (green colour cable for earth wire) continuity earth wire connected to common earth dolly to be drawn in and including PVC casing capping, medium grade of suitable size including all fittings such as bend, elbow, tee, joint etc with sunk cast pressed steel terminal box made out of MS sheet with 3 mm thick hylum laminated sheet cover/ plastic gang box for mounting of switch, socket and fan regulator complete all as specified and as directed.

All as per item Srl No. 121.00 here-in-before but for 5 Amp socket point on same switch board

All as per item Srl No. 121.00 here-in-before but for 5 Amp socket point on independent switch board.

BLANK

All as per item Ser No 121.00 here-in-before but with 2.5 sqmm PVC insulated, unsheathed cable multistranded FRLS type, copper conductor (for phase & neutral) and 1.5 sqmm (for earth wire with same specification) for 6/16 Amp switch socket point on independent board.

S&F switch piano flush type 5/6 Amps, 230 volt, one way, single pole complete all as specified.

S&F socket out let 5 pin, multipurpose type, 5 Amps, piano flush type, 230 V complete all as specified.

S&F switch socket combination 2 in 1, 5 pin, multipurpose type, 5/6 Amps, piano flush type 230 V complete all as specified.

Supply and fixing switch socket combination, multipurpose type 6 pin 5/15 A 240 Volts piano flush type complete all as specified and directed.

S&F ceiling rose 3 terminals/ PVC/ polycarbonate, isolated body, surface type with ISI marked 230 V complete all as specified.

S&F stepped type electronic type fan regulator, piano flush type, 230 volts, 50 Hz suitable for 1200/1400 mm sweep ceiling fan complete all as specified.

S&F in replacement of submain wiring with 2 x 4.0 sqmm, PVC insulated unsheathed copper conductor cable, multistranded, single core, FRLS type, 1100 volts grade alongwith 1x 4.0 sqmm PVC insulated unsheathed copper conductor cable, multistranded, single core, FRLS type, 1100 volts grade for continuous earth wire complete drawn through and including PVC casing caping, medium grade of suitable size with all fittings such as bend, elbow, tee, joint including making good the disturbed surface complete all as specified and directed. Note : Three runs of 4.0 Sqmm cable and one run of casing caping shall be measured as one length.

S&F in replacement of submain wiring with 2 x 6.0 sqmm, PVC insulated unsheathed copper conductor cable, multistranded, single core, FRLS type, 1100 volts grade alongwith 1x 6.0 sqmm PVC insulated unsheathed copper conductor cable, multistranded, single core, FRLS type, 1100 volts grade for continuous earth wire complete drawn through and including PVC casing caping, medium grade of suitable size with all fittings such as bend, elbow, tee, joint including making good the disturbed surface complete all as specified and directed. Note : Three runs of 4.0 Sqmm cable and one run of casing caping shall be measured as one length.

Material and labour for concealed sub main wiring with two run of 6.0 sqmm PVC insulated unsheathed FLRS copper conductor single core multi stranded and one run of insulated copper earth wire 6.0 Sqmm drawn through and including PVC medium grade conduit complete including cutting and chasing to the surface and making good to match with existing surface complete all as specified and directed by Engr-in-Charge. Note : Three runs of 6.0 Sqmm cable and one run of PVC conduit shall be measured as one length.

M&L in repair of steel tubes, light grade galvanised of 50mm bores laid in trenches/ surface/wall for cable protection including necessary fittings as clamp, nuts, bolts complete all as specified and directed.

Supply and fixing in replacement of decorative type, round shape, 15 watt, 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in replacement of bulk head luminaire environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit LED luminaire comprising of high brightness LEDs 10 Watt, 230 Volts, 50 Hz including lamp, connection wire all as specified and directed.

S&F in replacement of recessed mounted 36 Watt (clear white) LED panel light 2x2 feet, ultra slim design, 230 volts, 50 Hz with CRCA sheet housing precoated white colour and high quality diffuser for uniform light and high efficiency with separate replaceable electronic driver including lamp complete all as specified.

BLANK

Supply and fixing LED lights fitting 1 X 18/20 W, 220V, AC decorative box type with driver including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete including taking down old one all as specified and directed.

BLANK

S&F in replacement of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED light fitting with high out put diffuser 2 feet,10 watt 220 V AC decorative type with driver and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete including taking down old one all as specified and directed.

S&F in replacement sheet metal enclosure MCB DB SPN concealed double door type AC 240 V 8 way with 200 Amps rated bus bar, vertical/ horizantal type including making good of distructed surface complete all as specified and directed.

S&F in replacement of sheet metal enclosure, MCB DB, double door, single pole & neutral, 4 way, 230 volts, 50Hz with suitable bus bar, neutral link, earth link complete all as specified.

S&F in replacement of sheet metal enclosure, MCCB DB, TP&N, vertical type, double door with bus bars, neutral links, 4 way, 415 volts, 50 Hz suitable for MCCB 3/4 pole as incomer & MCB SP/TP as out going complete disturbed surface all as specified.

Supply & fix MCB SP 10 to 32 Amps, 230 volts, C curve, 10 kA complete all as specified and directed.

Supply & fix MCB SPN 32 Amps, 230 volts, C - curve, 10 kA complete all as specified and directed.

S&F in replacement of MCB single pole, 10 to 32 Amps, 230 volts, 10 kA , C series complete all as specified.

S&F in replacement of MCB single pole and neutral 16 to 32 Amps, 240 volts, 10 kA, C series complete all as specified.

S&F in replacement of MCCB 3 pole, 100 Amps, 415 volts, 16 kA, fixed type complete all as specified.

M&L for earthing complete with copper plate 600mm x 600mm x 3mm thick electrode and 20mm x 3mm copper strip as earthing lead burried directly in ground vertically (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level, the earth plate surrounded by adequate quantity of charcoal dust and common salt to a packed thickness of 15 cm on all sides connected to copper strip 20 x 3mm as earth lead by means of tinned copper/ brass bolts, nuts, check nuts and washers (including brazing) connected to main switch board / panel/ test point at the other including necessary earth work in any type of soil, returning filling in and removal of surplus soil, concrete pit in PCC (1:3:6) type C1, pre cast RCC 1:2:4 type BI cover slab 54cm x 54cm x 5cm reinforce with 8mm dia bar TMT @150mm centre to centre both ways with one handle for lifting made out 8mm dia MS bar with wire mesh funnel, 20mm GI tubing medium grade for watering and 40mm GI tubing light grade for protection, test point, testing on completion all as shown in Electrical Plate No 3 of SSR Part-I includoing taking out old complete all as specified and directed.

Supply, testing & hanging of energy saving non-decorative ceiling fan 230 volts, single phase AC, 1200 mm sweep, BEE 5 star rated, Brushless Direct Current (BLDC) without remote type complete with accessories like holding down rod, hanging clamps, blades including writing MES number (as per standard practice) & flexible three core copper conductor cable of suitable size for connecting with ceiling rose complete all as specified and directed. Note:- Contractor will provide guarantee of ceiling fan against any type of defect for a period of minimum two years from the date of completion of work and rate for same is deemed to be included in the item quoted rate.

S&F exhaust fan metallic steel body, single phase, 230/ 240 volts, 50 Hz of size 300 mm sweep, 900/950RPM, heavy duty type with suitable metallic louver, blades, frame including making of hole in existing wall and making good to the distubed surface to match with existing surface complete all as specified. Note:- Contractor will provide guarantee of exhaust fan against any type of defect for a period of minimum two years from the date of completion of work and rate for same is deemed to be included in the item quoted rate.

M&L for earthing complete with galvanised steel earth plate 800mm x 600mm x6mm thick electrode and 4mm galvanised iron wire as earthing lead burried directly in ground vertically (earth pit not less than 2.25mir deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level, the earth plate surrounded by adequate quantity of charcoal dust and common salt to a packed thickness of 15 cm on all sides connected to Gl wire 4mm as earth lead by means of bolts, nuts, check nuts and washers (including welding) of galvanised iron or steel and connected to main switch board /DB/ test point at the other including necessary earth work in any type of soil, returning filling in and removal of surplus soil, concrete pit in PCC (1:3:6) type C1, pre cast RCC 1:2:4 type BI cover slab 54cm x 54cm x 5cm reinforce with 8mm dia bar TMT @150mm centre to centre both ways with one handle for lifting made out 8mm dia MS bar with wire mesh funnel, 20mm GI tubing medium grade for watering and 15mm Gl tubing light grade for protection including testing on completion all as shown in Electrical Plate No 3 of SSR Part-l complete including taking out old all as specified and directed by Engr-in-Charge.

Note:- Schedule of cedit (Sch 'A' Part- II) amount of Rs 6,50,296.00 shall be deducted from the total quoted amount of BOQ.

M/s Dhani Enterprise

M/s Dhruv Enterprises

M/s PRABIR ENTERPRISE

M/S P R SINGH AND SONS

M/S. SUBHAS CONSTRUCTION CO.

Rajan Traders

Jasvit Constructions Private Limited

FRIENDS CONSTRUCTION