Comprehensive repair and maintenance to various roads under Division South Road-II, PWD during 2025-26 and 2026-27. (SH_ Providing and Fixing signage boards at different locations under Sub Division - I, II, III and IV).

DSR Items Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m.

All kinds of soil

Providing and laying in position excluding cement concrete of level: specified grade the cost of centering and shuttering - All work up to plinth

1:1.5:3 (1 Cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

1:5:10 (1 cement : 5 coarse sand (zone-Ill) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On steel work

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. NOTE: Payment will be made as per weight slip issued by authorised MCD dumping ground after dumping of malba. Processing fees at prescribed rate of authorised MCD dumping ground will be submitted by the agency & shall be reimbursed by the department on production of receipt in original.

Modified Estimated Cost after using Correction factor on DSR 2023 on account of GST @ 0.973

Add Cost Index @ 3% (On DSR Item)

Non DSR Items Providing, installing and fixing with necessary clamps etc. retro-reflective Single Sided directional/mandatory/ cautionary shoulder mounting signboards comprising of customized modular PU Epoxy coated MS tube, frame work, aluminum composite panel (ACP) , digitally printed micro prismatic retro-reflective sheet signages with QR Codes. i. The horizontal and vertical members of the MS frame module shall be made of MS tube 50x50x3.6mm thick as per approved drawing and each panel shall be braced diagonally (one way only) with same section. ii. The aluminum composite panel (ACP) shall have thickness of 4mm consisting of 3mm thick Non FR grade thermoplastic core of LDPE/HDPE sandwiched between two 0.50 Aluminum sheets. The ACP Sheet shall be PVDF on one face and another face will be mill finish for pasting retro reflective sheet. The ACP shall be routed, folded and fixed on the MS frame with VBH tape, 24mm wide and 2.3mm thick of approved brand & made provided throughout the length and breadth of the frame including riveting at the right angle face of the frame with pop riveting or with self taping SS screws 5mm dia spaced not more than 300mm center to center on both side of frame ensuring that no riveting is seen on either face of the frame. iii. On the front face of the ACP, micro prismatic retro reflective sheet conforming to Type-XI of IRC 67-2022 and ASTM:D4956-17 with digitally printed signs on top of the base retro reflective sheeting covering the entire sign facia (end to end) shall be pressure fixed. The sign shall be manufactured using a system of matched components of reflective sheeting and overlay films and digital inks manufactured and supplied by the reflective sheeting manufacturer. The digital printer and digital ink shall be approved by the reflective sheeting manufacture. Digitally printed traffic colour (which ever required) areas on white sheeting shall not be having less than 70 percent of the value of the coefficient of retro reflective established for its colour and type of sheeting. iv. The rear side of the MS frame shall be covered with balancing ACP sheet of the same description as mentioned above and shall be fixed in similar manner as described above. The edges of the board shall be covered alround with 50 micron powder coated die cast extruded aluminum channel of required color and shade of size 68x12x2mm. the channel shall be fixed using two rows of double sided VHB tape of above description. The channel shall further be secured by pop riviets having SS screws of 5mm dia at junctions and corners. v. Labes/QR Code to be printed on signage at bottom right side corner (2”x2”) with details like name of manufacture, date of manufacturing, code of reflective sheeting used, warranty etc. Note: The rate shall include all materials, labour, equipments, fabrication transportation, erection, installation and incidentals all complete as per direction of Engineer-in-Charge. Only front area of the board shall be measured for payment.

Providing, installing and fixing with necessary clamps etc. retro-reflective Single Sided gantry/overhead and cantilever mounted signboards comprising of customized modular PU Epoxy coated MS tube, frame work, aluminum composite panel (ACP) , digitally printed micro prismatic retro-reflective sheet signages with QR Codes. i. The horizontal and vertical members of the MS frame module shall be made of MS tube 50x50x4.50mm thick as per approved drawing and each panel shall be braced diagonally (one way only) with same section. ii. The aluminum composite panel (ACP) shall have thickness of 4mm consisting of 3mm thick Non FR grade thermoplastic core of LDPE/HDPE sandwiched between two 0.5mm Aluminum sheets. The ACP Sheet shall be coil coated with kynor 500 base PVDF on one face and another face will be mill finish for pasting retro reflective sheet. The ACP shall be routed, folded and fixed on the MS frame with VBH tape, 24mm wide and 2.3mm thick of approved brand & made provided throughout the length and breadth of the frame including riveting at the right angle face of the frame with pop riveting or with self taping SS screws 5mm dia spaced not more than 300mm center to center on both side of frame ensuring that no riveting is seen on either face of the frame. iii. On the front face of the ACP, micro prismatic retro reflective sheet conforming to Type-XI of IRC 67-2022 and ASTM:D4956-17 with digitally printed signs on top of the base retro reflective sheeting covering the entire sign facia (end to end) shall be pressure fixed. The sign shall be manufactured using a system of matched components of reflective sheeting and overlay films and digital inks manufacuted and supplied by the reflective sheeting manufacturer. The digital printer and digital ink shall be approved by the reflective sheeting manufacture. Digitally printed traffic colour (which ever required) areas on white sheeting shall not be having less than 70 percent of the value of the coefficient of retro reflective established for its colour and type of sheeting. iv. The rear side of the MS frame shall be covered with balancing ACP sheet of the same description as mentioned above and shall be fixed in similar manner as described above. The edges of the board shall be covered alround with 50 micron powder coated die cast extruded aluminum channel of required color and shade of size 68x12x2mm. the channel shall be fixed using two rows of double sided VHB tape of above description. The channel shall further be secured by pop riviets having SS screws of 5mm dia at junctions and corners. v. Labes/QR Code to be printed on signage at bottom right side corner (2”x2”) with details like name of manufacture, date of manufacturing, code of reflective sheeting used, warranty etc. Note: The rate shall include all materials, labour, equipments, fabrication transportation, erection, installation and incidentals all complete as per direction of Engineer-in-Charge. Only front area of the board shall be measured for payment.

Providing, installing and fixing with necessary clamps etc. retro-reflective double sided road name/ place identification signboards comp

rising of customized modular PU Epoxy coated MS tube, frame work, aluminum composite panel (ACP) , digitally printed micro prismatic retro-reflective sheet signages with QR Codes. i. The horizontal and vertical members of the MS frame module shall be made of MS tube 80x40x4mm thick as per approved drawing and each panel shall be braced diagonally (one way only) with same section. ii. The aluminum composite panel (ACP) shall have thickness of 4mm consisting of 3mm thick Non FR grade thermoplastic core of LDPE/HDPE sandwiched between two 0.50 Aluminum sheets. The ACP Sheet shall be coil coated with kynor 500 base PVDF on one face and another face will be mill finish for pasting retro reflective sheet. The ACP shall be routed, folded and fixed on the MS frame with VBH tape, 24mm wide and 2.3mm thick of approved brand & made provided throughout the length and breadth of the frame including riveting at the right angle face of the frame with pop riveting or with self taping SS screws 5mm dia spaced not more than 300mm center to center on both side of frame ensuring that no riveting is seen on either face of the frame. iii. On the front face of the ACP, micro prismatic retro reflective sheet conforming to Type-XI of IRC 67-2022 and ASTM:D4956-17 with digitally printed signs on top of the base retro reflective sheeting covering the entire sign facia (end to end) shall be pressure fixed. The sign shall be manufactured using a system of matched components of reflective sheeting and overlay films and digital inks manufactured and supplied by the reflective sheeting manufacturer. The digital printer and digital ink shall be approved by the reflective sheeting manufacture. Digitally printed traffic colour (which ever required) areas on white sheeting shall not be having less than 70 percent of the value of the coefficient of retro reflective established for its colour and type of sheeting. iv. The rear side of the MS frame shall be covered with balancing ACP sheet of the same description as mentioned above and shall be fixed in similar manner as described above. The edges of the board shall be covered alround with 50 micron powder coated die cast extruded aluminum channel of required color and shade of size 68x12x2mm. the channel shall be fixed using two rows of double sided VHB tape of above description. The channel shall further be secured by pop riviets having SS screws of 5mm dia at junctions and corners. v. Labes/QR Code to be printed on signage at bottom right side corner (2”x2”) with details like name of manufacture, date of manufacturing, code of reflective sheeting used, warranty etc. Note: The rate shall include all materials, labour, equipments, fabrication transportation, erection, installation and incidentals all complete as per direction of Engineer-in-Charge. Only front area of the board shall be measured for payment.

Credit for Steel ACP Sheet and Aluminium Channel etc. received from signages at site including disassembling of Old/damaged signages from gantries, cantilevers etc. as it is where it is basis with help of hydra etc. complete, inclusive of all expenses, [Area of board shall be measured for payment (credit) purpose], complete as per direction of Engineer-in-charge.