REPAIR TO ROOF BRICK WORK PLASTERING AND PAINTING TO NEW OLD SURFACES INCLUDING MISC B R WORKS VARIOUS BLDGS IN KANJOLI LINES AT BHARATPUR MIL STN

Amount

Dismantling asbestos cement (corrugated or semi corrugated) sheets in roof coverings, complete all as specified.

S&F pre painted galvalume alumimnium zinc coating GI based corrugated steel sheet 0.50 mm thick, sheeting of any colour having strength of 550 mpa as in roof covering etc, complete all as specified.

S&F pre painted galvalume alumimnium zinc coating GI based plain steel sheet 0.50 mm thick sheeting of any colour having strength of 550 mpa as in roof covering etc, complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified.

Dismantling timber scantlings 40 Sqcm and over in section from unframed work, complete all as specified.

Excavating in post holes (or similar holes) in soft/loose soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified.

M&L for cement concrete type C-2. 1:3:6 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete, complete all as specified.

M&L for cement concrete type B-1. 1:2:4 (using 20 mm graded stone aggregate)in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections & MS pipe) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A', complete all as specified.

M&L for mild steel work as in wind ties for roof covering including securing bolts etc. including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 290 Gde E-165, complete all as specified.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground levels) complete all as specified.

M&L for 100 mm thick PCC 1:2:4 type B-2 (using 40 mm graded stone aggrgate) as in floor laid in panels finished even and smooth with using extra cement complete all as specified.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection/path laid in panel surface finished even and fair without using extra cement complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified.

M/L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cm 1:6 complete all as specified.

M&L for coloured non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc. 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified.

M&L for glazed ceramic tiles, coloured/printed tiles in vertical surface of size 450x300x7 mm thick, laid over and including 15 mm thick rendering in cement mortar (1:4) and set and jointed in neat cement slurry & pointed in white cement with pigment to match the colour of tiles, complete all as specified.

M&L for 20-25 mm thick kota stone slab as in flooring/steps laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 20 mm thick screed bed in CM 1:6, complete all as specified.

M&L for 18 - 20 mm thick black machine cut granite slab (of any type) (table rubbed and polished), as in steps, jambs, pillars, window- cills, cooking platform set in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab laid over and including 15 mm thick cement screed in cement and sand mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for rounding to edges of stone slab one edge, such as in steps, cooking platform and other similar situation including making of hole suitable for gas pipe etc. complete all as specified.

Dismantling of Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified.

M&L for sand stone slabs of 50 mm thick in cills, sun-shades, chajjas, shelves, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4, complete all as specified.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc complete all as specified.

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc complete all as specified.

S&F GI tubing medium grade ISI marked galvanised with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified.

S&F GI tubing medium grade ISI marked galvanised with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified.

S&F in repair vitreous china wash down water closet (Pedestal pattern) white with seat cover excluding (flushing cistern and flush pipe), complete all as specified.

S&F in repair vitreous china squatting pan,Órissa pattern size 580 x 440 mm white, with integral foot rest and CI 'P' trap complete, all as specified.

M & L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified.

S&F of welded steel wire fabric ,weight n. exc 4.00 kg/sq. m fixed to steel members complete all as specified.

Demolition & breaking up drain pipes AC, (Salt glazed ware, AC or Reinforced concrete) set in CM Internal dia of pipe 100 mm/75 mm complete all as specified.

S&F PVC (SWR) pipe not less than 6 Kgf/sqcm rating single socketed, in any length with rubber ring joints including clamps of FI 40x3 mm fixed bolt 8 mm drilled to wall, in walls, type 'B' ISI marked of 110 mm bore complete all as specified.

S&F PVC (SWR) pipe not less than 6 Kgf/sqcm rating single socketed, in any length with rubber ring joints including clamps of FI 40x3 mm fixed bolt 8 mm drilled to wall,in walls, type 'B' ISI marked of 75 mm bore complete all as specified

S&F PVC (SWR) bend of 110 mm bore with access door of any radius including taking down of bend, complete all as specified.

S&F PVC (SWR) bend of 75mm bore with access door of any radius including taking down of bend, complete all as specified.

Taking down chowkats or frames n. exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all as specified.

Taking down chowkats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters (without taking off shutters from the frame) complete all as specified.

S&F 30 mm thick Flush Shutters, Solid core construction, Single or double rebating shall be square or splayed, with block board core and both face is covered with plywood face panels commercial type free from twist or wrap in plane, complete all as specified.

S&F factory made, 35 mm thick, 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc.( without sash bars ), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified 8.24(a) in SSR Part I complete as as specified.

S & F for Solid PVC Door Frame of the size 50 x 47mm made out of 5 mm PVC sheet. The door profiles are to be reinforced with 19x19mm M.S Square tube. The profile shall be cut and mitred at two corners and joined by inserting 2nos. of 150mm long brackets of 15x15mm M.S. square tube inside the 19mm x 19mm M.S. square tube and suitably screwed complete all as specified.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified & shown on SSR 2020 (Part-II) complete all as specified.

S&F MS butt hinges medium weight cold rolled of size 100 mm, complete all as specified.

S&F stainless steel hinges medium weight of size 100 mm, complete all as specified.

S&F aluminium anodised, barrel tower bolts of extruded section, 125 mm length of bolt and fixed with screws, complete all as specified.

S&F 200 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws complete as as specified.

S&F Aluminium handles, cast type, anodised of 125 mm size complete all as specified.

M & L for Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including, jointing cleats for fixing etc., complete all as specified .

S&F Powder coated Anodised aluminium window/ ventilator shutters side hung type with sash, aluminium section weight not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stay 150 mm long (1 No) suitable , type B-21 hinge 100 mm long (2 No), suitable handle (1 No) etc for each leaf, complete all as specified .

S & F Sheet glass 4.0 mm thick, ordinary quality & glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified.

S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples or rivets, complete all as specified.

Demolition of brickwork or stone boulder masonry built in cement mortar including all quoins, arches, pillars etc, complete all as specified.

M & L for brick work with sub-class 'B' bricks, straight or curved on plan exc 6.0 metre mean radius as wall built in cement & sand mortar 1:6, complete all as specified.

Taking down cement or cement lime plaster of any description from brick or stone walls including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified.

M&L for rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces including finishing the surface even and fair complete all as specified.

M&L for rendering 5 mm thick in cement and sand mortar 1:3 on fair faces of concrete surfaces as in ceiling including finishing the surface even and smooth without using extra cement, complete all as specified.

M&L for rendering 15 mm thick in cement and sand mortar 1:4 on brick work or cement concrete surfaces including finishing the surface even and smooth, complete all as specified.

M&L for preparation of newly plastered or un plastered surfaces of walls and applying two coats of oil emulsion distemper white or tinted over one coat of water based white pigmented alkali resistant priming paint, over 2 mm thick wall care putty on Wall Surface including all necessary arrangement for execution of work ,complete all as specified.

M&L Preparation of newly plastered surfaces of ceiling & applying two coats of oil emulsion distemper white or tinted over a coat of primer complete all as specified.

M & L Preparation of new decorated plastered surface of wall including cornices, pilasters etc by brooming down and applying two coats of Exterior emulsion over a coat of alkali resistant primer complete all as specified.

M&L for painting to new or previously untreated steel surfaces of any description over 10 cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chrome primer including preparation of surfaces complete all as specified.

M&L for painting to new or previously untreated steel surfaces of any description n exc10 cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chrome primer including preparation of surfaces complete all as specified.

M&L for preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

Cutting or uprooting grass incl removing old mud phuska/ roof treatment of any thickness and description, removing rubbish off the premises, cleaning surface and preparing to receive new treatment complete all as specified.

M&L for 40 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in sub base complete all as specified.

M&L for 20 mm thick screed bed or bedding layer of cement mortar 1:4, finished even and smooth without using extra cement complete all as specified.

Providing and laying APP(Atactic Polypropylene polymer) modified prefabricated five layer 4mm thick water proofing membrane,black finished reinforces with nonwoven polyester matt consisting of a coat of bitumen primer of bitumen membrane @ 0.40 litre/sqm by the same membrane manufacturer of density at 25 degree C 0.87-0.89 Kg/litre and viscosity 70--160cps.Over the primer coat the layer of membrane shall be laid using Butane torch and seiling all joints etc and preparing the surface complete. The vitalphysical and chemical parameters of the membarane shall be as under: Joint strength in longitudinal and transvrese direction at 23 degree C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membarane not less than 150 degree C. Cold flexibility shall be up to -2 degree C when tested in accordance with ASTM,D complete all as specified.

abhinav and company (BID ID -3302518)

GANGA CONSTRUCTION (BID ID -3304052)

krishna Associate (BID ID -3304361)

GOVIND CONSTRUCTION (BID ID -3301773)

M/s S. K. Construction Co. (BID ID -3304493)

Tulsi Enterprises (BID ID -3304360)

M/s Ranaji Construction Co (BID ID -3304502)

AMIT RISHABH BUILDERS PRIVATE LIMITED (BID ID -3304064)