ADDN/ ALTN OF BLDG NO 22 and 23 FOR CREATION OF MEDICAL FACILITIES FOR COVID-19 AT COD UNDER GE (NORTH) DELHI CANTT-10

Amount

Dismantling of AC sheet roof corrugated/semi corrugated of any description including ridges/gutters etc at height upto 15 mtr complete all as specified and directed.

Demolition of reinforced cement concrete in roof floor (other than ground floors) beams staircase, landing chajja and similar work complete all as specified.

Demolition of brick/stone masonry built in CM. all as specified.

S&F 0.80 mm thick PGI sheet as in ridges, hips, drip and straight, flashing etc having 275 gm of zinc coating per sqm (both side inclusive) fixed with L or J hook or cranked hook bolts up to 15 mtr hight complete all as specified and directed.

S&F 2 mm thick Stainless steel sheet as in valley gutters,eaves gutters, drip, and straight, flashing etc having 275 gm of zinc coating per sqm (both side inclusive) fixed with L or J hook or cranked hook bolts up to 15 mtr hight complete all as specified and directed.

M&L factory made continous line prefabricated sandwith panel LLOYD/JINDAL/JSW/TATA BHUSHAN PUF Panel of 30mm thick insulated roofing & wall cladding sandwich system with 40+/-2 kg/cum density comprising of external sheet manufactured out of 0.5mm TCT (total coated thickness) permanenntly colour coated galvalume steel (150 gsm. zinc-aluminum alloy coating total of both sides) having 550 Mpa yield strength trapezoidal profiled with crest ht.min 40mm at pitch of maximum 333mm, the inner sheeting shall be a liner tray of thickness 0.5mm permanently colour coated galvalume steel sheet with sight ribbed. The prefabricated panel shall be fixed through the profile directly to the purlins using self-drilling fasteners with neoprene washers meachancally with the help of machines. complete all as specified and directed.

Providing & Fixing False ceiling with semi perforated 12mm thcik micro tegular edged at all heights with GRG (Glass Fibre reinforced Gypsum) false ceiling tiles of size 595x595mm of approved texture, design and pattern having moisture content less than 2%,humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non-combustible as per BS 475 (part-4)-1970 and light Code Description unit rate No 429 SUB HEAD :26.0 NEW TECHNOLOGIES AND MATERIAL reflectance of 85% minimum to be laid in true horizoatal level suspended on interlocking metel T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @ 120 grams oer sqm including both sides) comprising of main-T runners of size 15x32mm of length 3000mm, vross-T of size 15x32nn of lenght 1200mm amd secondry itermediate cross-T of size 15x32 of lenght 600mm to form grid module of size 600x600mm, suspended from ceiling using galvanised mild steel items (galvanising @ 80 grams per sqm) ie. 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on perimeter wall/partition with the help of plastic rawl pluhs at 450mm center to center and 40mm long dry wall screws. The work shall be carried out as per specification, drawing and as per direction of the Engineer-in-charge

S&F structural steel work for rolled sections as in main and cross beams, hips and jack rafters, purlins, running rails and guides for sliding doors, fixed with angle cleats or other connecting plates gde Fe-410-Wat any height complete all as spd and directed.

S&F 10 mm thick Toughened glass as in partition/ fixed window including diamond edging all sided , eatching , lining and momnograme area nexc 0.50 Sqm each by sand blasting , including CP " L" or " U" heavy duty clamps suitable for fixing of glass , min 4 mos per Sqm all as specified and directed.

PROVIDING & FIXING VERTICAL LINEAR BAFFLE BOX CURTAIN CLOSED CMADE OUT OF ALUMINIUM EXTRUSION OF 1.2MM THICKNESS. THE BAFFLE BLADE SHALL BE IN SIZE OF 30 X 200 X 3600MM IN POWDER COATED FINISH OF APPROVED SHADE. VERTICAL LINEAR BAFFLE BOX CURTAIN HAS TO BE FIXED ON EXTERNAL WALL FOR FAÇADE. RATES ARE INCLUSIVE OF FRAME WORK & FIXING / GROUTING ARRANGEMENT ON WALL ETC. MAKE :PROLAD/ HUNTER DOUGLAS/ SAINT GOBAIN

SUPPLY AND INSTALLATION OF CLADAGE 6MM THICK EXTERIOR GRADE UV PROTECTED FOR WALL/CEILING F- QUALITY PANELS OF STANDARD SIZE. CLADAGE INTERIOR PANELS ARE HIGH-PRESSURE LAMINATES (HPL) AS PER EN 438-7, TYPE EDF MANUFACTURED USING PATENTED TECHNOLOGY (NT), PANELS ARE DOUBLE HARDENED INCLUDING ACRYLIC POLYURETHANE RESIN WHICH IS THERMALLY CURED UNDER HIGH PRESSURE & HIGH TEMPERATURE. TERMITE FREE, WATER RESISTANT. EXPLANATION NT: NON FADING HIGH PERFORMANCE ACRYLIC POLYURETHANE SURFACE TECHNOLOGY. INSTALLATION OF CLADAGE PANELS WILL BE DONE BY HIGH QUALITY RIVETS WITH RECOMMENDED ALUMINUM ‘T’ SECTION AND ‘L’ SECTION HELD BY ALUMINUM WALL BRACKET WITH WIND LOAD AND DEAD LOAD SLOT AS PER DESIGN, ANCHORED BY STANDARD HILTI/FISCHER OR EQUIVALENT MAKE ANCHOR FASTENERS ALONG WITH THERMAL SEPARATOR . INSTALLATION OF CLADAGE PANELS WILL BE DONE USING REAR VENTILATED PRINCIPLES ONLY WHICH IS ENSURED BY PROVIDING 200 SQCM/ PER METER (FOR FREE FLOW OF AIR BEHIND THE FAÇADE) FOR THE FAÇADE AND USING THE FRAMEWORK WITH NO HORIZONTAL SECTION. MAKE : OREO/ALSTONE/GREENLAM ETC

Designing, providing, installing and fixing factory finished custom designed cold form Light Gauge Steel Framed super structure approved by BMPTC comprising of steel wall panel, trusses, purlins etc manufactured out of 0.75 mm to 2.00 mm thick steel sheet as per design requirements. The steel sheet shall be galvanized (AZ-150 gms Aluminum Zinc Alloy coated steel having yield strength 300- 550 Mpa) conforming to AISI specifications and IBC 2009 for cold formed steel framing and construction and also as per IS: 875- 1987 (Part-I; Dead Load , Part-II; Imposed load, Part-III; wind load , Part-IV; Snow load, and Part-V; Special load & load combinations), IS 800- 1984 (Code of practice for general construction in steel) and IS: 801- 1975 (Code of Practice for Use of Cold Formed Light Gauge Steel Structural Members In General Building Construction). The wind load shall be as per provisions of IS 875 (part -III). LGSFS frame shall be designed as per IS: 801 using commercially available software such as Frame CAD Pro-11.7/ STAAD PRO-V8i/ArchitekV2.5.16/ Revit architecture2011 or equivalent. The framing section shall be cold form C-type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple/slot at required locations as per approved drawings. The slots will be along centre line of webs and shall be spaced minimum 250mm away from both ends of the member. The frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. All self drilling tapping 168 screws for joining the members shall have a Type II coating in accordance with ASTM B633(13) or equivalent corrosion protection of gauge 10 & 12, TPI 16 & 8 of length 20mm. The frames shall be fixed to RCC slab or Tie beam over Neoprene rubber using self expanding carbon steel anchor bolt of dia as per approved drawings, design subject to minimum 12mm diameter and 121mm length conforming to AISI 304 and 316 at 500mm c/c with minimum embedment of 100mm in RCC and located not more than 300mm from corners or termination of bottom tracks complete in all respects.

Providing and fixing internal wall panels on Light gauge steel frame work with 12.5mm thick gypsum plaster board conforming IS 2095:2011 fixed on 8mm thick fiber cement board conforming to IS 14862:2000 of category III type B (High pressure steam cured) as per standard sizes fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make, Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of length varying from 25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately)

Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density C,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete all as per specified and directed

Providing and fixing Trim for window and door 1mm thick with zinc coating not less than 275gm/m3 galvanized sheet material Girth up to 400mm complete all as per specified and directed

S&F 10 mm thick toughened frosted glass door shutters of size area exc 1.50 Sqm but not exc 3 Sqm , including necessary floor spring hydraulically regulated , otherside fixed on pivot. CP fittings and fixtures , CP handles , CP locking arrangement , necessary cutting & holes moulding and fixed in complete as specified and directed

M&L for 900 mm x 300 mm x 12 mm thick glazed exterior tiles fix with neat cement slury over 20mm thick screeding in cement mortar 1:4 and including 100 mm thick PCC 1:4:8 type D2 & pointing with epoxy mortar all as specified and directed.

S&F Factory made UPVC white colour sliding windows area n. exc 2.00 sqm each. Three track made of extruded profiles with wall thickness of 2.3 mm (+/- 0.20 mm). Windows profiles with hollows section with multi chamber. Frame size (88 mmX 52 mm). Sliding sash (42 MM X 67 MM), sliding Mesh sash (42 mmX 57 mm), sliding interlock (one vertical length in each shutter)(45.5 mmX 28 mm).glazing bead (24.5 mmX 16 mm) will be mitered cut and fusion welded at all coeners, including drilling of holes for fixing of hardware and drainage of water etc, making arrangement for fixing of hardware, EPDM gasket, 1.2+/- 0.20 mm thick galvanised steel frame (30mm X 28 mm) 2 nos sliding sash ( 30mmX 18 mm), sliding mesh (26 mm X 10 mm),profile to be inserted in required orofile frame will be fixed to the wall with 8 mm X 100 mm long fastener hardware.(Touch lock of zinc alloyed (white powder coated ), steel roller system, Staineless steel wire 0.36 mm nominal dia of wire and averahe width of aperture 1.40 mm and required accessories) Note:- The unit rate qoatedby contractor excludes cost of glass and includes all another connected accessories ie, wire mesh and hard wares , complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), all as specified and directed

S&F 35mm thick pre-laminated designer factory made flush shutter of laminate or equivaqlent including necessary hardware and fittings all as specified and directed

M&L for factory made 100% solid wood plasticcomposite(WPC) Door frame of size 65 X 32 mm with density 780 kg/Cum Make Rajshree or Eqv all as spd and directed.

Dismantling structure steel work incl door, gates, rolling/sliding shutters but excluding framed trusses etc all as specified and directed

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair complete all as specified.

M&L for Vitrified Ceramic coloured tiles 10 mm thick (square/rectengular) polished, size of each tiles is 800x800mm as in floors, over 15 mm thick screed bed in CM 1:4 and joint shall be kept as 3mm filled with epoxy. to attain the best result 3mm thick tile spacers to be used, Masking tape shall be put before putting the eposy grout & the grout shall be throughly cleaned immendiatly. complete all as specified and directed.

M&L for glazed coloured ceramic tiles in dado/vertical surface (450mm x600mm x 7-8 mm) thick fixed with chemical adhesive Fevi Mate of euivalent and joint shall be kept as 3mm filled with epoxy. to attain the best result 3mm thick tile spacers to be used,Masking tape shall be put before putting the eposy grout & the grout shall be throughly cleaned immendiatly, complete all as specified and directed.

M&L for Non skid coloured ceramic tiles (square/rectengular) 7 to 8 mm thick area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface,including 15 mm thick in cement mortar 1:4 complete all as specified and directed

M&L for glazed coloured ceramic tiles in dado/vertical surface (450mmx 300mm x 7mm) thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface including 10 mm thick in cement mortar 1:3 even and fair for receving tiles on vertical surface complete all as specified and directed

M & L Fibre galss reinforced plastic (FRP) door frames shall be three lagged of cross section 90mm x 45 mm having single rebate of 32mm x 15mm to receive shutter of 30 mm thickness. The laminate door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. MS stay shall be provided at the bottom to steady the frame all as specified and directed”.

M & L FRP door shutter shall be 30mm thick glass fibre reinforced plastic (FRP) panelled door shutter of required colour and approved brand and manufactures. Made with fire retardant grade unsaturated polyester resin moulded to 3mm thick FRP laminate for forming hollow rails and styles with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP panels and confirming to IS 14856-2000”.

S&F floor door stopper, aluminium alloy body and tongue anodised with hard drawn steel spring of 140mm size overall.

S&F for 150mm size aluminium anodised barrel tower bolt of extruded section and fixed.all as specified and directed.

S&F for 150mm size aluminium anodised handle of febricated type and fixed.all as specified and directed.

Supply and fixing of stainless steel butt hinges medium weight 100 mm long fixed to frame as required complete all as specified.

S&F aluminium alloy,anodised,sliding door bolt plate type 250 mm long and fixing clips of sheet ,cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified .

S&F 20 mm dia decorative drapary curtain road with bibs, braked & internal funnels. complete all as specified.

M&L for 5.5mm thick plain sheet glass exc. 0.50 sqm each pane. all as specified and directed.

S&F Vitreous china wash down water closet pan (pedestal pattern), floor mounted with inbuilt P trap in white colour, including connection to trap and to flushing pipe including provn of cement concret beading complete all as specified and directed.

S&F EWC Seat cover white colour of PVC complete all as specified and directed.

S&F 32/40 mm dia PVC waste pipe for WHB/sink complete all as specified

S&F PVC low level flushing cistern 10 ltrs capacity incl PVC float valves, PVC connection and out let pipes complete.

S&F Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges aluminium anodized, fixed with rawl plugs. all as specified.

S&F PVC connection 15mm size with PTMT nuts of lengh 450mm complete all as specified.

S&F Table top wash basin, white, flat back size 525x415x140mm of make -Jaquar cat part No JDS-WHM-25907N or equvalent excluding tap, chain, plug but including brackets, waste fitting 32mm dia ,brass chromimium plated for glazed ware sink, basin,with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified.

S&F 15 mm Quarter turn basin mixer without Popup waste system with 357mm Long braded hoses of make Jaquar cat part No-ALI-85001 or equvalent for fixing hot & cold waterscrewed down for iron pipe and fixed all as specified and as directed.

S&F vitreous china Squatting pan "Orissa pattern" size 580x440xmm white, with integral foot rest incl p trap and necessary connection to trap and flushing pipe etc complete all as specified and directed.

S&F fancy type stop valve make of jaquar or equivalent copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions chromium plated of size 15 mm. all as specified

All as per Srl item No 47 above but fancy type, chromium plated with long shank and cup (concealed type)

S&F of Quarter turn Bib tap make of jauar cat part No ALI-85037 with wall flange or equvalent for iron pipe of size 15mm bore chromium plated. all as specified

S&F Ball Brass Valve high pressure with polythine coat and fly nut complete screwed for Iron pipe or brass ferrule and fixed of size 25mm bore. all as specified

S&F rotational moulded polyethylene water storage tanks in three layer ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 liters including all accessories complete all as specified .

S&F rotational moulded polyethylene water storage tanks in three layer ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 5000 liters including all accessories complete all as specified .

M&L Gun metal globe of gate valve with iron wheel head, screwed both ends of size 15mm

M&L Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20mm

S&F 2 in 1 Angle Valve 15 mm CP fancy pattern type cast copper alloy make of jaquar or equivalentscrewed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F Angle Valve 15 mm CP fancy type cast copper alloy make of jaquar or equivalent screwed for iron pipe or forbrass ferrule and fixed all as specified

S&F CP hand spray (health facucet with 1.5 M long easy flex tube in chrome finish and wall hook) make of jaquar or equivalentcomplete all as specified and directed.

S&F chromium plated jet for WC with 1.00 M long pipe including necessary fittings complete all as specified and directed.

S&F Vitreous China half stall urinals, (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. incl of fixing supply pipe to flushing cistern, trap and waste pipe)

S&F Urinal Spreader of CP White colour fixing to 15 mm bore pipe.

M&L 15mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified.

M&L 20 mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified.

M&L brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 all as specified.

M&L for PCC type D-2 ,1:4:8 ,using 40mm graded crushed stone aggregate as in sub base , mass concrete all as spfd. .

M&L half brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:4 all as specified and directed.

M&L for Rendering 15 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified. (Water proofing compound to be measured and paid for separately).

M&L for Rendering 10mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified.

Supply only liquid water proofing compound complete all as specified.

M&L for preparation of New steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer. all as specified.

M&L for preparation of Old steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer after copmlete removal and preparation of old existing surface complete all as specified.

M&L Preparing newly plastered surfaces or unplastered of walll and applying two coats of weather proof exterior emulsion paint on any surface as approved and directed by Engr-in-charge.

M&L two coats of oil bound distemper on walls including preparation on new surfaces over coat of primer incl applying 3 mm thick layer of wall putty on walls to give uniform surface complete all as specified and directed.

S&F cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints laid in trenches all as specified.

S&F cast iron soil, waste and vent pipes (sand cast) 75mm bore in any length with or without ears with cement joints laid in trenches all as specified.

S&F cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints fixed to walls duly apply a coat of bitumenous black paint complete all as specified and directed.

All as per srl item No 75 above but 75mm bore pipes fixed to wall

S&F Salt glazed stone ware gully traps square or round mouthed, type P of size 150x150mm set and jointed to drain pipe with cement mortar (1:1) all as specified.

S&F Cast iron bend (any radius) diminishing pieces or tapers 100mm bore fitted with oval access door. all as specified.

S&F Cast iron bend (any radius) diminishing pieces or tapers 75mm bore fitted with oval access door.

S&F Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100/110mm bore pipe.complete all as specified and directed.

S&F Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore complete all as specified.

S&F Cast iron branch pieces single (equal unequal ordinary or inverted (Spigot or socketed type) or with parelled branches 75mm bore (fixed in repairs)

S&F Cast iron branch pieces single (equal unequal ordinary or inverted (Spigot or socketed type) or with parelled branches 100mm bore all as specified.

PVC (SWR) pipes 110mm bore single socketed , in any length with rubber ring joints fixed to wall

S&F cast iron vent cowl for 75mm dia pipe complete all as specified.

S&F cast iron floor trap 75 mm, with grating including jointing to waste pipe . all as specified.

S&F PVC(SWR) bends plain 110 mm bore complete all as specifed and directed.

S&F cast iron floor trap 75 mm, with grating including jointing to waste pipe . all as specified.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

M&L for Providing & Pouring Micro concreting M-40 grade :- (i) Dry concrete substrate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade, Make : MasterEmaco S46T of BASF or equivalent FOSROC/SIKA using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc,. Adding of aggregates will be permitted only as per manufacturer’s recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed. Note : The cost of micro concrete M-40 grade & Epoxy bond coat is inclueded in this item.

Providing and injecting chemical emulsion for post constructional Antitermite treatment treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 liters per sqm of the vertical surface of sub-structure to a depth of 300 mm including excavating channel along the wall and rodding etc. complete all as specified.

Treatment of soil under exiting floors using emulsion @ one liter per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 Cement: 2 coarse sand) to match the existing floors.

M&L for 16-18 mm thick black granite stone work (table rubbed and polished) laid over and including 20 mm thick screed bed or bedding layer in CM 1:4 as in steps, Jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, front and side of slab moulded and polished complete all as specified and directed by Engr-in-Charge. Granite stone slab shall be laid in single piece with rounding of edges and a grove shall be provided beneath the projection portions of stone slab and provn of hole for gas pipe shall be provided.”

M&L RCC M-25 (DESIGN MIX ) TYPE B0 1:2:4 USING 12.5 MM GRADED AGGREGATE AS IN SLAB SUPPORTED ON WALLS , BEAMS, Plinth or roof beam LANDING & AS IN SHELVES AND THE LIKE COMPLETE ALL AS SPECIFIED AND DIRECTED

M&L FORM WORK TO SOFFITS OF SUSPENDED SLABS SUCH AS ROOF SLAB , FLOOR SLAB , LANDING , Beams SHELVES AND THE SIMILAR WORK NOT EXCEEDING 200 MM THICK (HORIZONTAL & SLOPING) COMPLETE ALL AS SPECIFIED AND DIRECTED

ALL AS PER SRL ITEM NO 95 (here-in-before) BUT EDGES OF CONCRETE

M&L MILD STEEL TMT BARS 10 MM DIA & OVER , CUT TO LENGTH AND BENT TO SHAPE AS REQUIRED INCLUDING CRANKING BENDING , SPIRALLY FOR HOOPING , FOR COLUMN AND INCLUDING MILD STEEL WIRE (ANNEALED) NOT LESS THAN 0.9 MM DIA OR SECURING WITH CLIPS.

S&F STAINLESS STEEL SINK 1 MM THICK FOR KITCHEN OR LABORATORY WITH PLUGS, WASHER INCLUDING BEDDING IN CEMENT MORTAR INTO DWARF WALL/SLAB OR INCL FIXING CANTILEVER BRACKETS & CONNECTING UNION TO PIPE OVERALL SIZE 915MMX 460 MM , BOWL SIZE 410X330X160 MM incl l etc WITH WASTE COUPLING & PIPE COMPLETE ALL AS SPECIFIED AND DIRECTED

PROVIDING & FIXING AT SITE FULLY GLAZED PARTITION TO BE MADE UP OF 200 MM OR (AS PER SITE TOP AND BOTTOM SECTION) TO BE MADE UP WITH 19 MM COMMERCIAL BOARD , THE MIDDLE PORTION OF THE PARTITION SHALL HAVE FULLY GLAZED 2000 MM (H) ,12 MM PLAIN TOUGHENED GLASS INCL MONOGRAME AREA NOT EXCEEDING 0.5 SQM EACH TO BE FIXED TO TOP & BOTTOM FRAME WITH HELP OF TEAK WOODEN BIDDING , WOODEN PARTITION OF THE PARTITON SHALL HAVE 1 MM THICK LAMINATED FINISH ON BOTH SIDED OF APPROVED SHADE AND FINISH.THE WOODEN BIDDINGS TO HAVE MELAMINE POLISH.THE COST SHALL INCLUDE ALL LABOUR,MATERIALS ,FIXING FIXTURES & ARRANGEMENTS ,CONTINGENCIES, TRANSPORTATION ETC

PROVIDING & FIXING AT SITE PARTIALLY GLAZED PARTITION WITH 50 X75X1.2 MM ALUMINIUM BOX FRAME WITH SPACING AT 600-900 C/C HORIZONTALLY & VERTICALLY, TO BE SANDWICHED WITH 8 MM COMMERCIAL PLY FORM BOTH THE SIDES AND FINISHED WITH 1 MM THICK APPROVED SHADES OF LAMINATED FINISH, THE MIDDLE PORTION TO HAVE 8 MM PLAIN FLOAT MM.GLASS TO BE FIXED IN PARTITION ABOVE 3 FEET AND UPTO 7 FEET LEVEL TO BE FIXED WITH 1.25 INCHES x 1 INCHES TEAK WOODEN BIDDING.THE COST SHALL INCLUDE ALL LABOUR,MATERIALS ,FIXING FIXTURES & ARRANGEMENTS ,CONTINGENCIES, TRANSPORTATION ETC

PROVIDING & FIXING AT SITE VERTICAL BLINDS 100 MM WIDE WITH EXTRUDED POWDER COATED HEAD RAIL HOUSING CONTROL UNITS , SPACERS , RUNNERS , TILT ROD WITH REDUCTION GEAR MEACHANISM, TILT CONTROL FOR ROTATION OF 180 DEGREE LOUVERS MASE OF APPROVED FABRIC /COLOUR SCOTCH GUARD COATING AND BOTTOM MECHANISM OF POWDER COATED GALVANISED STEEL WITH REQUIRED COMPONENTS AS SPECIFIED AND DIRECTED

PROVIDING & FIXING AT SITE WALL PANELLING WITH 50x25 MM ALUMINIUM BOX SECTION PLACING AT EVERY 300 MM C/C TO BE FIXED OVER THE WALL/COLUMN AS PER SITE REQUIREMENT TO BE FINISHED WITH 12 MM BWP GRADE PLY & 8 MM COMMERCIAL GRADE HDF PANEL TO BE FIXED AT SITE OVER THE 12 MM PLY WITH GROOVED PATTERN, TO BE FINISHED WITH 1MM LAMINATES OF APPROVED COLOUR AND SHADE , IS TO BE FIXED AS PER THE GIVEN DESIGN AND PATTERN ALL EXPOSED MEMBERS TO BE DULY PAINTED TO MATCH THE EXISTING SHED OF PANELLING. BIDDING.THE COST SHALL INCLUDE ALL LABOUR,MATERIALS ,FIXING FIXTURES & ARRANGEMENTS ,CONTINGENCIES, TRANSPORTATION ETC

PROVIDING & FIXING AT SITE APPROVED DESIGN & PATTERN OF ETCHING FILM TO BE 3 M 7725—325 PRESSURE SENSITIVE FILM FOR PERMANENT GRAPHIC FIXED AT SITE OVER THE GLAZED AREA AS PER THE GIVEN DESIGN & DRAWING INCLUDING ALL MATERIALS, WASTAGE ETC COMPLETE

M&L Mono sink mixer of make Jaquar or equivelent incl all cutting into slab,granite or fixed to wall etc

Wrighting letters and figures (Block, roman, italic & Indian) not exc 30 CM hight of stainless steel as directed by Engr -in- Charge

Index hands (Natural size) and arrows (upto 40CM long) as directed

M&L for RCC M25 (Design mix) in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns,etc.; basement slabs,under-reamed piles and mass concrete.

M&L for RCC M25 (Design ) in columns, pillars, piers, posts and struts.

M&L for RCC M25 (Design mix) in chajjas,etc

Reinfoced cement concrete (Design mix) type B1 1:2;4 using 20mm graded aggregate as in roof beam, cantilever, bressummers, lintels over 1.50 span complete all as specified and directed.

M&L Hardcore brocken stone or boulders of gauge n.exc 63mm, depositied,spred and levelled in layers n.exc 15CMthick wtered and rammed to a tru surface

M&L for 100mm thick PCC 1:2:4, type B1 using 20mm graded stone agg as in floor all as specified and directed..

M&L MILD STEEL TMT BARS 6mm to 8mm , CUT TO LENGTH AND BENT TO SHAPE AS REQUIRED INCLUDING CRANKING BENDING , SPIRALLY FOR HOOPING , FOR COLUMN AND INCLUDING MILD STEEL WIRE (ANNEALED) NOT LESS THAN 0.9 MM DIA OR SECURING WITH CLIPS.”

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and matt beams sides and soffits (if any) of foundation and plinth beams; and similar work ; vertical or to batter or flat

Use and waste formwork to sides of pillars. posts. struts. piers. columns and stan- rchions for fair finished surfaces of concrete, square.

Formwork to chajjas hoof, chajjas, though and similar items inclding edge

Formwork to sides and soffits of floor or roof beams, beam haunchings, girder,lintel etc

M&L One coat anti-bacterial paint of Make-Asian paint royal health shield or equivalent over two coat of Plastic Emulsion paint, required shade of approved brand and manufacturer over a coat of 2mm thick approved wall care putty including preaparation of undecorated surface of wall complete all as specified and directed. Colour/shade as approved by GE

M&L for udaipur green marble 18- 20 mm thick machine cut, bedded jointed and pointed with grey cement slurry including,moulding eadge cutting and polishing types with screed bed or bedding layer of mortar 20mm thick in cement mortar 1:3 laying floor finishes . all as specified.

Moulding of Granite/marble stone full round complete all as specified.

M&L Providing and fixing Glazed Fire Door of size 2100 mm X 2100 mm with the following specification : (a) Hollow metal fire rated Glass Fixed Partition as per BS 476 -Part 22 & IS 3614 part-1 & part-2 for stability and integrity. Pressed Galvanized steel confirming to IS 277 with specifications as stated below. Recommended fire doors shall have door tested at SIRIM for maximum rating of two hours with Fire Glass vision panel. Test certificates should be available for vision lites /panels as part of the fire door assembly. The doors supplied should be within the tested specimen, deviation in specification and sheet thickness other than what is mentioned in the test certificates is not allowed. Proper label confirming the type of door and the hourly rating is mandatory for every door assembly. (b) Door frame shall be Single rebate frame profile of size 100 x 58 mm made out of 1.6mm minimum thick Stainless Steel sheet (Grade SS-304). Frames shall be Mitered / Butt Joint and field assembled with self tabs. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Once frame is installed, should be grouted with cement & sand slurry as necessary for fire doors.

(c) Door leaf shall be 47 mm thick fully flush double skin door with vision lite. Door leaf shall be manufactured from 1.2mm thick Stainless Steel sheet (Grade SS-304). The internal construction of the door shall have reinforcements for receiving appropriate hardware. The infill material shall be resin bonded honeycomb core. All doors shall be factory prepped for receiving appropriate hardware. The edges should be interlocked with lock seam. For pair of doors astragals will be provided as required. 200x300m Vision lite wherever applicable should be provided as per manufacturers recommendation with a beeding and screws from inside. The glass should be 10 MM thick fire rated glass of Schott Make with relavant rating of the door.

S&F 1.7mm thick lead sheet on doors & door frames of X-Ray room with necessaary fixing arrangement as per AERB guidelines.

Description of Work / Item(s)

Amount

S&F water heater storage type (Geyser), electric capacity 25 litres, vertical type with all accessories, BEE 5 star rated, to be fixed on wall with suitable fixing arrangement incl connection complete all specified and directed.

S&F water heater storage type (Geyser), electric capacity 10 litres, vertical type with all accessories, BEE 5 star rated, to be fixed on wall with suitable fixing arrangement incl connection complete all specified and directed.

S&F cold water PVC connection with brass union at both end, 45 cm long, 15mm bore complete all specified and directed.

S&F hot water connection pipe, heavy duty, SS rope threaded type with brass union at both end, 45 cm long, 15mm bore complete all specified and directed.

Description of Work / Item(s)

Amount

Supply and fix refrigerator, electric driven (single phase), capacity 192 Litres, inverter type BEE 5 star rated with all accessories complete

Description of Work / Item(s)

Amount

OUTDOOR UNITS : Supply, Installation, Testing and Commissioning of air cooled variable refrigerant flow, modular type condensing units, each comprising of multiple scroll compressors all inverter driven, full charge of refrigerant gas (Refrigerant to be R-410a), lubricating oil and all accessories as per the specifications. The condensing units shall be suitable to work on cooling as well as heating mode with the minimum Two Air Changes through TFA Unit (Treated Fresh Air Unit) . The minimum Energy Efficiency Ratio shall be as per ASHRAE STANDARDS 90.1 -2019 table 6.2.1B. The condensing units shall be suitable for operation on 415 ± 10% volts, 50Hz, 3 phase AC power supply and the condensing units shall be of following capacities (Note :- The outdoor units shall be provided with anti corrosion treatment from factory and the quoted price shall be inclusive of same) :- (a) 22 HP nominal capacity

(a) 1.0 TR nominal capacity

(b) 1.5 TR nominal capacity

(c) 2.0 TR nominal capacity

(d) 2.5 TR nominal capacity

(e) 3.0 TR nominal capacity

(f) 3.5 TR nominal capacity

(ii) Ceiling mounted ductable Units with remote

(a) 8.0 TR nominal capacity

Supply, install, commissioning and testing of commercial Air curtain unit for prevention of dust and conditioned air losses, three phase 440 V, 50 Hz, made out of MS/ CRCA sheet of minimum thickness 18 gauge finished with two coats of red oxide primer and final coat of synthetic enamel paint (oven baked) with MS - CRC 18 gauge square perforated suction grills, Aluminium alloy fans and single phase electric motor, nozzles etc, complete with fittings and accessories so as to produce 1- 1.5 m/sec air velocity at floor level for door opening size 70" x 96" complete all as specified and directed

Note :- The contractor shall submit heat load calculation and layout plan/ drawings for above air conditioning work duly marked items included in BOQ (Schedule) for approval within 21 days from date of commencement

Description of Work / Item(s)

Amount

Supply and fix air termination, single, pointed aluminium rod 12mm dia and 300 mm long, to be fixed with GI pipe 25mm including necessary fixing & clamping arrangement on roof top as required at site incl necessary civil/ PCC work complete all as specified and directed (Note :- GI pipe 25mm will be measured and paid seperately)

M&L for test cum bimettalic inspection joint gun metal or phosphouras bronze size 75 x 75 x 25 mm connecting piece for jointing down conductor of aluminium strip & GI earth strip and fastened with nut & bolts and aluminium ends soldered and complete joint housed in MS box of 25cm x 30cm x 15 cm fabricated from 3 mm thick steel sheet welded & screwed complete including testing system all as specified and directed

S&F aluminium strip 25 x 3.15 mm with shaddles and fixing screws etc for roof and down conductors above ground complete all as specified and directed.

S&F pipe galvanised medium grade including fitting complete of size 25mm dia for fixing of air terminations complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick directly buried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of earth plate not less than 1.5m below the ground level connected to GI strip 32 x 6mm by means of bolts nuts check nuts and washers of galvanised iron at 2 points & GI pipe 15 mm bore light grade for protection of earthing wire PCC chamber 1:3:6 (type C-1) using 20mm graded stone aggregate, watering pipe 20mm bore light grade, funnel with wire mesh, 50 mm thick cover of RCC 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8 mm MS bars at 150 mm centre to centre both ways and charcoal dust and common salt all as shown in electrical plate No. 3 of MES SSR part-I and including excavation & earth work & connecting the earthing point/equipment and testing complete all as specified and directed.

Supply and fix GI strip 32 mm x 6 mm buried in ground complete all as specified and directed.

Note :- The contractor shall submit lightning protection system layout plan/ drawings duly marked items included in BOQ (Schedule) for approval within 21 days from date of commencement.

Description of Work / Item(s)

Amount

Supply, installing, testing and commissioning of outdoor type plinth mounted step down transformer, 11 KV/433 Volts (at no load), Level -II, AC 3 phase 50 Hz, 800 KVA capacity, core type, double copper wound, oil immersed, naturally cooled, Oil Natural-Air Natural (ON AN), with external cooling tubes, delta connected on primary side (HV) and star connected on secondary side (LV) in accordance with vector group DYN-11 with Neutral brought out on secondary side (LV side) and having tapings at +5% to -10% in steps of 2.5% on HV side to be changed by means of hand operated off load tap changer gear. The maximum temperature rise should not exceed 40 degree celsius in oil and 45 degree celsius in HV/LV winding when measured by resistance method after continuous full load run on an ambient temp of 40 degree celsius. The transformer shall be of BOLTLESS core design. Transformer shall be double wound, core type wil low loss, non ageing, high permeability PRIME GRADE, CARGO with M4 Grade or Better, perfectly insulated and clamped to minimize noise and vibrations. The transformer shall be IS 1180 (Part-I) : 2014 and shall comprise of the following :-

(a) One cable box on HT side (primary side) consisting of three nos porcelain bushing with copper rods, complete with nuts and washers, with cable glands suitable for reception / taking out 3 core 185 Sq mm, HT 11000 volts grade, XLPE insulated and PVC sheathed, heavy duty, armoured cables including jointing materials complete. (b) One cable box on LT side (Secondary side) consisting of four nos porcelain bushing with copper rods, complete with nuts and washers, with cable glands suitable for reception/suitable for connection in bus bar turking (BBT). (c) Oil conservator with filter type drain valve and oil level guage. (d) De-hydrating breather with first fill of dehydrating agent (silica gel). (e) Explosive vent, Thermometer pocket on tank cover, Oil level gauge, Oil drain filter valve, Lifting lugs, Oil filling hole with cap / plug with connection plate complete, Airrelease valve plug and four nos plain solid cast steel detachable rollers.

(f) One no 100 mm dia, dial type thermometer, vapour pressure type, having range 0-120 degree celsius with metal guard having maximum perimeter temperature reading indicator with re-setting device. (g) Two earthing terminals on tank cover to facilitate fixing of 50 x 6 mm galvanised iron earth strip for earthing of body. (h) Rating plate and terminal marking plate. (j) Extra bushing for neutral, in the LT cable box for providing independent set of earthing for neutral. (k) First fill of new and unused transformer oil, IS-335 marked, filtered and tested upto 40 KV dielectric strength at 2.5 mm air gap between testing electrodes (l) Providing adequate size and nos of channels, embeded in floor, for movement of transformer. (m) Unidirectional roller wheel. (n) Other accessories as per manufacturer design. NOTE : Transformer shall be supplied inclusive of initial oil filling to appropriatelevel of insulation oil with desired dielectric strength.

Supply, installation, testing and commissioning of manufacturer’s factory manufactured and tested sheet steel clad / enclosed HT Vacuum Circuit Breaker (VCB) switchgear, indoor type, dust & vermin proof, motorised as well as manually charged, fully interlocked, horizontal draw out horizontal isolation type, floor mounted, 11 KV, 630 Amps aluminium busbar, 3 phase, 50 Hz, 21 KA/3 sec as per IEC 62271-200, extendable type, to be coupled with existing VCB make CG, type UNIVAC including adapter panel (if reqd). The charging time of motor shall be less than 15 Sec making it suitable for rapid auto reclosing duty and safety shutters shall be provided to cover up the fixed high voltage contacts on bus bar and cable side when the bus trunk is moved to test/isolation position with all standard accesssories and metering equipments and comprising of followings complete all as specified. (a) Three single phase horizontal draw out type resin cast line type potential transformer of 11KV/110 volts, 50VA burden per phase class 1.0 accuracy connected star/star on HV side with HV&LV fises, isolating plugs, for HV side and LV connection. (b) CT dual ratio, 100/50/5+5 Amps rating, class 5P10 for protection & class 1.0 for metering 10 VA burden, short time rating 21 KA for 0.1 sec suitable for 11 KV - 03 Nos.

(c) Instrument & Protection Panel - Numerical relay with LCD display, 3 OC+1 EF, trip circuit supervision function, inrush protection, record and store at least 500 Events with Date and Time stamp, Last 10 Fault Records stored in Nonvolatile memory, Disturbance recording, self supervision function, 4 CT & 3 PT analog input, 8 DI & 6 DO, negative sequence currents, circuit-breaker-failure alarm, tripping circuit failures, Communicable on 61850 protocol, Breaker Control (ON/OFF) feature, suitable with 18 to 50 VDC complete with separate master trip relay. (d) Digital Voltmeter and Amp Meter, Digital Multifunction Meter (Accuracy class 0.5) with LCD display for measuring of current, voltage, power, power-factor, energy parameters, Total Harmonic Distortion and Maximum Demand Indication etc and shall have RS-485 port for communication on ModBus protocol. (e) LED indicating lamps for Breaker ON, Breaker OFF, Spring charged, TCH, Auto trip indicator, DC Supply ON, RYB phase indications. (f) T&C Switch for closing / tripping of VCB and Local Remote switch. (g) Heater with switch, thermostat and illumination. (h) 3 Pin plug socket with switch. (j) 01 No shunt trip coil and closing coil 24V DC (k) Emergency switch

(b) AC Alternator (Brush Less) : The AC alternator (Generator) shall be designed for an output of 750 KVA/600 KW at ful load for continous rating 10% for over load for one hour at 0.8 (lag) PF conforming to IS-4722 & 13364 or BS-5000 RPM 1500 including self excited and self regulating Electronic voltage panel with all accessories cable termina bo suitable size of glands earth terminal etc complete all as per OEM specifictions.

(c) Diesel Engine : The engine shall be vertical multi cylinder four stroke 1500 RPM water cooled with water pump asembly battery charging alternator of suitable instrument panel, electronic in built governor starting bateries heavy duty with leads (as recommended by the manufacturer) suitable size and length of exhaust pipe with necessary clading materials, exhaust coupling inside accousitc enclosure/canopy, silencer and exhaust pipe above canopy al as fixtures all as per OEM specification complete as per IS 1602 or BSS-649 & suitale BHP for the generator, (BHP not less than 1180 BHP) according to IS-10002, BS 5514, supply and installation of diesel engine driven generating set in cooperating engine of minimum 1180 BHP/1500 RPM turbocharged after cooled water cooled with alternator of 750 KVA/600 W 415 VF 0.8 PF 50 Hz AC brushless alternator mounted on a common base frame alongwith all standard accessories i.e. fuel tank, electric reinforcement of 8mm TMT bars & 100mm c/c borth directions including MS angle in frame of 40 x 40 x 3mm etc to acheive earth resistance less than 01 Ohm including testing comlete a complete relay panel for noise free compartment (acouustic enclosure) housing all as directed

(e) The tools as per the manuacturer's list shall be provided by the contractor alongwith the set at no extra cost. (f) Unit rate quoted shall deemed include the control cable from DG set to AMF panel, DIESEL OIL, LUB OIL, COOLANT FOR RADIATOR etc for smooth functioning of DG SET during PH I & PH II complete testing (at factory premises before dispatch & at site after commissioning) and full tank filling of DIESEL OIL after PH I & II testing (at factory premises before dispatch & at site after commissioning) topping of LUB OIL, COOLANT FOR RADIATOR etc required for commissioning and testing of DG Set

Supply, install, testing and commissioning of Voltage stabilizer for automatic operation, three phase naturally oil cooled indoor type & designed for input variation between 340 V to 460 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second and of capacity 750 KVA complete all as specified and directed.

(iv) 3 Nos of CTs of ratio 1250/5 copper wound, Class 1.0, 10 VA – 1 Set (iv) Indicating lamps R,Y and B Phase : 01 set of three OUTGOING (i) ACB drawn-out type with adjustable microprocessor release confirm to IS/IEC:60947-2, 4 pole , LT 415 Volts, 50 Hz AC grade of 630 Amps rating 50 KA rupturing capacity with suitable for adjustable over load current and short circuit and earth fault protection - 02 No (ii) MCCB 4 pole , LT 415 Volts, 50 Hz AC grade of 315 Amps rating 25 KA rupturing capacitiy with adjustable Themal and Meganetic setting releases, - 01 Nos. Note : (i) All incoming and outgoing feeder shall be connected by cable through suitable size glands & thimples. (ii) The various feeders shall be indicated by 50mm size letters in synthetic enamel white paint.

Supplying, laying, jointing testing and connecting in replacement XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) 120 sqmm 3 core with multistranded aluminum conductors, 11 KV grade, IS 7098 marked, suitable for HT 11 KV(E) system, laid in trenches / ducts / encased in GI pipe / fixed to pole, including jointing & testing complete all as specified and directed (Note :- Excavation, earth work ,cable protection , sand fillings , cable joint shall be measured and paid separately under respective items of schedule)

Supplying, laying, jointing testing and connecting in replacement XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) 400 sqmm 3.5 core with multistranded aluminum conductors, IS 7098 marked, suitable for LT 1100 Volt system, laid in trenches fixed to pole, including jointing & testing complete all as specified and directed (Note :- Excavation, earth work ,cable protection, sand fillings, cable joint shall be measured and paid separately under respective items of schedule)

All as per item No - 08 above but size 630 sqmm 3.5 core.

All as per item No - 08 above but size 16 sqmm 4 core.

Supply and fix Cable jointing kit for 11 KV (Earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core 120 sqmm XLPE armoured aluminium conductor cable complete all as specified and directed.

Supply and fix Cable jointing kit for 11 KV (Earthed) grade cable for indoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core 120 sqmm XLPE armoured aluminium conductor cable complete all as specified and directed.

Supply and spreading fine river sand in trenches for cushioning of under ground cable complete all as specified and as directed. Note : Measurement shall be taken after punning down.

Supply and laying factory made non-reinforced precast concrete cable cover class HV type-I with size 300mmx180mmx40mm all as specified and directed.

S&F sub class B bricks having minimum compressive strength 75 Kg/ Sqcm laid in trenches for cable protection etc complete

Horizontal boring holes upto 2 m deep in soil for laying HDPE and getting out and disposal of spoil to a distance of n exc. 50 m up to 200 mm bore complete (Note:- The GI Pipes should be measured and paid separately under respective items).

M/L for HDPE pipe,of size 140 mm dia suitable for 0.6 MPA working pressurewith all fitting , laid in trenches for protection of cable in road /drain crossing complete all as specified and as directed.

Supply and fix Energy saving, environmental friendly, long life, LED street light made up of pressure dia cast aluminium housing with high efficient lighting source with toughened glass having IP66 protection LED street light of capacity 70 Watt complete all as specified and directed.

M&L for street light bracket made out of 32 mm dia GI tubing medium grade upto 1.5 mtr long including bending, welding ,drilling holes as required and fixing with flat iron clamps 25x 5 mm thick (02 Nos) with suitable nut, bolts and washers to steel tubular /concrete poles/wall complete all as specified and directed.

S&F KIOSK box weather proof made out of PVC, one piece moulded SMC base and out door pole mounted hinged door size 333 x 233 x 120 mm out side and 300 x 200 x 105mm inside dimensions comprising of aluminum bus bar 4 strips for 3 phase and neutral 63 Amp and 6 Amp MCB SP with base for controlling the street light, FI clamps 30x4 mm with necessary MS nuts bolts and washers including embossing/painting of Danger notice of size not less than 10 cm x 7.5cm with letters, figures and conventional skull and bones in signal red colour on front face of KIOSK box body complete all as specified and directed.

Supply and fix steel tubular swaged poles type 410 SP-31 (9 meter long) approx wt.147 kg conforming to IS 2713 (Part-II) complete with CI base plate etc complete all as specified and directed .

Material and labour plain cement concrete 1:3:6 mix, type C2 using 40mm graded stone aggregate as in foundations all as specified and directed.

Material and labour plain cement concrete 1:2:4 mix, type B1 using 20mm graded stone aggregate as in coping including necessary form work, exposed surface of concrete shall be finished even and smooth without using extra cement all as specified and directed.

Supply drawing, connecting and testing in replacement 3 core, 1.5 Sqmm PVC insulated and PVC round sheathed copper conductor (flexible ) industurial cable, 1100 Volts conforming to IS 694 in steel tubular poles from KIOSK box to street light fitting including providing suitable copper lugs all as specified and directed

Description of Work / Item(s)

Amount

M & L for Boring holes under road pavement by bocky manually, in any type of soil upto 150 mm bore Complete all as specified and as directed.

Supply, laying jointing,testing 100mm DI pipe with class-K-7 spigot socketed ends , conforming to IS-8329 laid in trenches connection complete all as specified and directed (Note : Tyton Joint, Excavation & earth work shall be measured & paid separetely.)

Supply, laying jointing,testing 150mm DI pipe with class-K-7 spigot socketed ends , conforming to IS-8329 laid in trenches connection complete all as specified and directed (Note : Tyton Joint, Excavation & earth work shall be measured & paid separetely.)

Material and labour for DI specials such as Tees, bends of any size and radius, collars, tapers, tail pieces, caps and plugs etc upto 150mm bore complete all as specified and directed

M&L Rubber Gasket Joint (Tyton Joint) including jointing material for DI/CI pipe of following size/bore :- (a) 100 mm bore

(b) 150 mm bore

M&L including jointing and testing of cast iron sluice valves class PN-1.0, conforming to IS14846 flanged ends drilled having stainless steel spindle with cast iron wheel at top complete with nuts, bolts, washers and rubber gaskets including connection complete all as specified for following sizes:-. (a) 100 mm bore

(b) 150 mm bore

Supply & Laying of GI pipe mediun grade ISI mark including all fittings in new positions in trenches/wall/floor complete and making good the distributed surfaces as directed of following sizes (Note : Excavation & earth work shall be measured & paid separetely):- (a) 20 mm bore

(b) 25 mm bore

(c) 50 mm bore

Supply & Fixing Gun metal gate valve with iron wheel head screwed both ends for iron pipe and fixed of following sizes connection complete all as specified and directed.of following sizes:- (a) 20 mm bore

(b) 25 mm bore

(c) 50 mm bore

Supply and installation of 150mm bore flanged ends strainer/dirt box, with stainless steel mesh suitable for water meter for potable water supplies on up stream of water meter to avoid foreign material entering into meter including connection complete all as specified and as directed at site.

Supply and installation of 150mm bore flanged ends Water Meter woltman type, including testing and making good connection with flanged ends, with gasket rubber sheet and nut & bolts etc ISI Marked fixing in horizontal/incline/vertical position,connection complete all as specified and as directed at site.

M & L for Construction of valves pit chamber having intermal dimention 120 cm * 120cm*120 cm (internal height) using PCC (1:4:8) 40mm graded stone aggregate for foundation 15 cms. Thick, 23 cm tick wall in CM (1:4), 10mm tick rendering all around the brick work with 1:6 cement mortar, PCC (1:2:4) type B1 coping with 20mm graded aggregate for grouting MS frame including 3mm tick MS top sheet cover with locking arrangement including 50mm pad lock with double key angle iron including painting of steel surface with two coats of synthetic enamel paint over a coat of red oxide primers including necessary excavation in any type of soil, returning filling in and removal of surpuls soil to a distance not exceeding 50 mtrs all as specified and directed

M&L for fabrication (welding work ) of MS Header of size upto 300mm MS pipe at COD pump house site for connection on header all as specified and directed.

Supplying , laying , jointing, welding and testing of 150mm MS Pipe (Heavy class 'C') IS : 1239/3589, laid in trenches or in Horizontal/Vertical/inclined position or laying on floors for connections for suction, to header and connected to out going water main DI pipe line, complete all as specified.:-( Note:- MS Flanges incl fabrication work will be measured and paid separately)

Supply and fixing MS flange 150 mm bore ,16mm thick duly welded with flange joint including nuts bolts ,washer ,Rubber or fiber board gasket joint of size 150mm size connection complete all as specified.

Description of Work / Item(s)

Amount

Excavation in over area n.exc 1.5m deep amd getting out in any type of soil. Complete all as specified and directed.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil.

Excavating in trenches n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil all as specified and directed.

Excavation for structure (eartwork in excavation of foundation of strucutre as per required, construction of shring and bracing, removal of stums and other deleterious matter, dressing of sides and bottoms, backfilling the excavation earth to the extent required and utilsing the remaining earth locally for road work). In ordinary soil, Manual Means: Depth uotp 3.00 (without dewatering

Excavating in post holes (or similar holes) each n exc0.50 cu.m, getting out, returning,filling in and ramming earth or rubble mixed with earth or PCC around in layers not exceeding 25 cm, watering and removing surplus soil to a distance n,exc 50 cm and making good surfaces in hard /dense soil.

Returning filling in, including spreading, levelling,watering and well ramming in layers not exc 25 CM complete all as specified and directed.

Removing excavated soil to a distance exc. 1.50KM but n exc 5KM and depositing where directed at alevel n exc 1.5m above the starting point complete all as specified and directed.

Note : All excavation earth work of all sch incl services shall be measured and paid under this sch.

Description of Work / Item(s)

Amount

Prime cost sum for certain E/M equipment and items Note :- Prime cost sum shall be measured and paid as per Condition 5 of IAFW-2249.

Provisional sum for Site Development and certain B/R items Note :- (a) Provisional items shall be measured and paid as per Condition 6 of IAFW-2249. (b) The estimated amount in column 6 is based on SSR (2010) Part-II rates

Description of Work / Item(s)

Amount

M&L for 100mm thick PCC type D-2 ,1:4:8 ,using 40mm graded crushed stone aggregate as in sub base , mass concrete complete all as specified and directed.

M&L for coloured precast cement concrete interlocking tiles 80mm thick, M-35 grade of any shape and size, conforming to IS-15658-2006 glossy finish as in floor/pavement laid on 75mm thick stone dust cushioning, laid dry to the profile over rammed earth/murrum filling complete all as specified and directed. Note :75 mm sand cushioning measured and paid separately

M/L PCC 1:2:4, type B1 using 20mm graded stone agg as in bencing and coping, apex stone etc complete all as specified and directed.

Suppy only fine aggregate (sand) for cushioning.

Description of Work / Item(s)

Amount

M&L cement concrete 1:3:6, type C-2 (using 40 mm graded stone agg) as in foundation, filling and mass concrete.

S&F mild steel bars TMT bars, 10 mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia or securing with clips.

All as per item No. 2 here-in-above but 8 mm dia TMT bar in stirrups, spaces, binders nibs etc.

S&F of mild steel screw bolts 11 to 15mm diameter (machine made) with hexagonal or square headss at one end and screwed ends fixed with two washers and one nuts fixed complete all as specified (dia of shank 10mm, length exc 10 cm but n.exc 15cm.

M&L for rolled angle iron section as posts and struts as in fencing incl cutting tops , drilling holes , notching for wire mesh , welding, incl all necessary drilling , bolting or riveting etc and similar work conforming to Fe-290 Gde E-165

S&F chain link fencing 100x100mm mesh made of 4mm dia galvanised steel wire including provision of binding wire.

M&L cement concrete in foundations filling and mass concrete Type -d, 1:4:8 ( 40 mm graded aggregates )

M&L for RCC M25 (Design mix) in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns,etc.; basement slabs,under-reamed piles and mass concrete.

M&L for RCC M25 (Design mix) in columns, pillars, piers, posts and struts.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and matt beams sides and soffits (if any) of foundation and plinth beams; and similar work ; vertical or to batter or flat

Use and waste forrnwork to sides of pillars. posts. struts. piers. columns and stan- rchions for fair finished surfaces of concrete, square.

M&L rendering 5 mm thick on walls in CM(1:3) finished even and smooth without using extra cement

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete FE -410 Gde E-250 quality

M&L preparing new steel surfaces of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zink chrome

M&L preparing new plastered surfaces and applying two coats of cement base paint on wall

Providing and fixing concentina coil fencing with punched tape concertina coil 600mm dia 10 mtr openable length (total length 90m) having 50 Nos rounds per 6mtr length upto 3m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.0m apart and including with 06 Nos horizontal R.B.T reinforced barbed wire of size 2.5x2.00mm weight not less than 108 gms per mtr lengh, stud tied with GI staples and clips to retain horizontal including necessary bolt or GI barbed wire tied to angle iron all complete as per direction of Engg-in-charge with reinforced barbed tape (R.B.T.)/spring core (2.5mm thick) wire of high tensile strenght of 165kh/sqmm with tape (0.52mm thick) and weight 43.478gm/meter (cost of MS angle, shall be paid seperatly)

Prepainted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strengh of 550 Mps , adjoining to main Fencing post. making to necessary holes to sheet to reduce wind presure on sheet as directed by Engg-in-charge. including supplying and fixing fixtures like with suitable dia GI bolts & nuts. Overlaping of sheet min 150mm of sheet, complete all as specified and directed by Engg-in-charge.

Description of Work / Item(s)

Amount

M&L for 100mm thick PCC type D-2 ,1:4:8 ,using 40mm graded crushed stone aggregate as in sub base , mass concrete complete all as specified and directed.

M&L PCC 1:3:6, type C2 (using 40mm graded stone agg) as in surfaces channels and drains incl necessary formwork complete all as specified and directed.

Extra for forming fair finishing to channels or drains, 30 cm inner girth in cement concrete using extra cement inclduing forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

Add or deduct from Srl No.06 here in above for each 25mm inner girth or part the of over or under 30 cm girth.

M&L for brick work with sub class 'B' bricks exc 6m mean radius straight or curved on plan built in cement mortar 1:4. all as specified.

M&L rendering 15mm thick in cm 1:4 concrete or brick surfaces as in wall finishes even andsmooth w/o using extra cement incl mixing of wpc . all as specified.

M&L PCC 1:2:4, type B-0 (using 12.5mm graded stone agg) in coping/ benching of drain and the like inclduing slightly rounded or chamfered angles all as specified and directed.

M&L reinforced cement concrete, M-25 as in cover slabs and similar work incl necessary formwork set in cement mortar 1:4.

S&F mild steel bars TMT bars, 10 mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia or securing with clips.

PCC 1:3:6 in foudation (Plain cement concrete 1:3:6 mix with crushed stone aggregate 40mm nominal size meachanically mixed, placed in foundation and compacted as as specified.

M&L of RCC Hume pipe (NP3 class) 450mm dia and 2.5m length as per IRC specification IS 456-1971 including all deads and lifts and cost of first class bedding of granular material/cement concrete M-15 grade using 20mm graded agrregate in single row including fixing coller with cement mortar 1:2, finish of suface should be with concrete surface 1:2:4, complete all as specified and directed.

M&L for RCC M25 (Nominal mix) in drain wall, footing,etc.; basement slabs,under-reamed piles and mass concrete.

Use and waste formwork to sides of concrete foundations/ drain, footings, bases of columns, raft and matt beams sides and soffits (if any) of foundation and plinth beams; and similar work ; vertical or to batter or flat

S&F frame work such as grills, gratings , drain cover etc complete all as specified and directed.

Description of Work / Item(s)

Amount

M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete ,using extra cement ,incl forms moulds ,mitered/stopped ends etc

M&L PCC 1:3:6 type C-1 as in surface channels/drains all as specified.

S&F SFRC manhole covers and frame medium duty of overal size 600mmX600mmX80mm thick, factory made and test load 10 tonnes (MD-10), strength as per IS: 1726-1991 (Make-Polycrete) all as specified by Engineer-in-Charge.

M&L for Plain cement concrete 1:4:8 typeD-2 using 40mm graded agg as in foundation filling and mass concrete complete all as specified.

Granular Class 'B' type bed to DWCPE drain pipe including packing under and haunching against the sides of the pipe after they are laid and tested with sand / crushed stone dust complete all as specified and directed .

Providing, lowering and laying DWCPE (SN8) pipes as per IS:16098 of 2013, 150 mm bore, laid and jointed with and including elastomeric sealing 'O' ring as per manufacturer's instructions complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to (150 mm / 200 mm bore) pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required

M&L for brick work with sub class 'B' bricks exc 6m mean radius straight or curved on plan built in cement mortar 1:4. all as specified.

M&L rendering 15mm thick in cm 1:4 concrete or brick surfaces as in wall finishes even andsmooth w/o using extra cement incl mixing of wpc . all as specified.

M&L For PCC type B1(1:2:4) using 20 mm graded cushed stone agg as in coping ,benching and the like including form work all as specified.

Supply only integral water proofing compound all as specified.

Description of Work / Item(s)

Amount

Material & labour for point wiring concealed type with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, for light/fan pointPVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC concealed conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories and modular metal flush box, modular white cover plate with frame, blanking plate etc suitable for up to required module etc complete and making good to the disturbed surfaces to match the existing complete all as specified and directed for the following:-

(a) One light point controlled by one one way switch

(b) Two light point controlled by one one way switch

(c) Four light point controlled by one one way switch

(d) One light point controlled by two two way switch

(e) One ceiling/ wall/ exhaust fan point controlled by one one way switch

(f) One bell point controlled by one one way switch

(g) One 5 Amps 3/5 pin socket outlet on same board with other switches

(h) One 5 Amps 3/5 pin socket outlet on independent board

All as per item no 1 above but with using 2.5 sq mm PVC insulated FRLS multi-stranded copper conductor for independent switch socket outlet 6 pin 5/15 Amps and incl 2.5 sqmm PVC insulated multi-stranded copper conductor single core as earth continuity conductor wire duly connected to all common earth point, drawn through 20 mm dia PVC conduit in any length all as directed at site all as specified and directed

All as per item no 1 above but with using 2.5 sq mm PVC insulated FRLS multi-stranded copper conductor on same board switch socket outlet 6 pin 5/15 Amps and incl 2.5 sqmm PVC insulated multi-stranded copper conductor single core as earth continuity conductor wire duly connected to all common earth point, drawn through 20 mm dia PVC conduit in any length all as directed at site all as specified and directed

All as per item no 1 above but with using 4 sq mm PVC insulated FRLS multi-stranded copper conductor for independent switch socket outlet 6 pin 5/15 Amps and incl 4 sqmm PVC insulated multi-stranded copper conductor single core as earth continuity conductor wire duly connected to all common earth point, drawn through 20 mm dia PVC conduit in any length all as directed at site all as specified and directed

S&F modular switch, 06 Amps, single pole, one way, 250 volts, one module and IP 20 protection complete all as specified and directed

S&F modular switch, 06 Amps, single pole, two way, 250 volts, one module and IP 20 protection complete all as specified and directed

S&F modular switch, with indicator, 16 Amps, single pole, one way, 250 volts, one module complete all as specified and directed

S&F modular socket outlet 05 Pin, 06 Amps, 02 module with shutter complete all as specified and directed

S&F modular socket outlet 02 in 01, 06 pin, 06 Amps and 16 Amps, 02 module complete all as specified & directed

S&F modular bell push with indicator, 06 Amps single pole, one way, 250 volts complete all as specified & directed

S&F modular fan regulator, stepped type of 0 to 05 rotary steps, electronic, 02 module, humfree, AC, 230 volts, 120 watts complete all as specified and directed

S&F Bell Ding Dong, AC, 230 Volts, Single pole incl connection complete all as specified and directed

S&F for lamp holder, PVC/Polycarbonate type of Normal/angular shape with back plate incl connection complete

S&F ceiling rose 6 Amps, 240 volts, AC, three terminals and connection complete all as specified & directed

S&F sheet metal enclosure with Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB with 20 Amps, 'C' series incl connection complete all as specified and directed

S&F sheet metal enclosure with Triple pole and earth encolsure with a three pin 32 Amps and earth plug with socket complete with one MCB TPN 32 Amps, 'C' series complete all as specified and directed

M&L for sub main wiring concealed type with 1.5 sqmm (Nominal area) with two runs of single core cable PVC insulated FRLS multistrand unsheathed copper conductor cable including 1100 V grade, drawn through conduit non metallic rigid PVC conduit 20 mm dia, medium grade, concealed in wall including all conduit and fixing accessories including 1.5 sqmm (nominal area) single core PVC insulated multistrand unsheathed copper conductor as earth wire and duly connected to all common earth point all as specified and directed.

M&L for sub main wiring concealed type with 4 sqmm (Nominal area) with two runs of single core cable PVC insulated FRLS multistrand unsheathed copper conductor cable including 1100 V grade, drawn through conduit non metallic rigid PVC conduit 20 mm dia, medium grade, concealed in wall including all conduit and fixing accessories including 4 sqmm (nominal area) single core PVC insulated multistrand unsheathed copper conductor as earth wire and duly connected to all common earth point complete all as specified and directed

M&L for sub main wiring concealed type with 6 sqmm (Nominal area) with two runs of single core cable PVC insulated FRLS multistrand unsheathed copper conductor cable including 1100 V grade, drawn through conduit non metallic rigid PVC conduit 20 mm dia, medium grade, concealed in wall including all conduit and fixing accessories including 6 sqmm (nominal area) single core PVC insulated multistrand unsheathed copper conductor as earth wire and duly connected to all common earth point complete all as specified and directed

M&L for sub main wiring concealed type with 10 sqmm (Nominal area) with two runs of single core cable PVC insulated FRLS multistrand unsheathed copper conductor cable including 1100 V grade, drawn through conduit including 10 sqmm (nominal area) single core PVC insulated multistrand unsheathed copper conductor as earth wire and duly connected to all common earth point complete all as specified and directed

M&L for sub main wiring concealed type with 6 sqmm (Nominal area) with four runs of single core cable PVC insulated FRLS multistrand unsheathed copper conductor cable including 1100 V grade, drawn through conduit including 6 sqmm (nominal area) single core PVC insulated FRLS multistrand unsheathed copper conductor as earth wire and duly connected to all common earth point complete all as specified and directed

S&F Sheet metal enclosure DB, single pole and neutral with 200 Amps rated bus bar,230 volts, glazed, double door type, IP-43, including connecting all connections of wire to MCBs with proper lugs & arrangements, making good to the disturbed surface complete all as specified and directed for the following way :-

(a) DB 4 way

(b) DB 12 way

Supply and fixing loadline distribution box 8 way, AC, TP & neutral metal enclosure, glazed double dooor, 415V AC, IP-43, concealed type with IP-43 protection complete with suitable bus bar, neutral link, earth link suitable for MCCB 4 pole, 125 Amps as incomer and MCB SPs as out going complete all as specified and directed

S&F MCB SP 240 Volts, AC, 6 to 40 Amps of breaking capacity, 10 KA, C curve incl connection complete

S&F MCB SPN 240 Volts, AC, 40 Amps of breaking capacity 10 KA C curve incl connection complete

S&F MCB TPN, 415 Volts, AC, 32 Amps of breaking capacity 10 KA C curve incl connection complete

S&F MCCB 4 Pole, 415 volt AC, 40 amps, fixed type with breaking capacity 16 KA suitable for load line TPN DB and connection complete all as specified and directed

Taking down carefully copper/aluminium point wiring (light/fan/socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc including making good the disturbed surfaces to match with the existing complete

Taking down unserviceable main switches, DBs, metal enclosure boxes, bus bars chambers etc from wall / existing main boards and removing from site complete all as directed

Taking down unserviceable light fittings of any type and removing from site complete all as directed

Taking down unserviceable sub main wiring and removing from site complete all as directed

S&F LED Batten type fitting for surface/wall mounted 20W, 230V, 6500K integrated electronic driver completely pre wired, LED 4 feet fitting with polycarbonate housing & integrated electronic driver complete with connector blok, screws, gutties etc. complete all as specified and directed

S&F LED Batten type fitting for surface/wall mounted 9W, 230V,6500K integrated electronic driver completely pre wired, LED 2 feet fitting with polycarbonate housing & integrated electronic driver complete with connector blok, screws, gutties etc complete all as specified and directed

S&F recessed mounted LED panel type of size 2 ft x 2 ft , 36 W, 230V, 5700K complete with driver full window glare free opal diffuser LED panel with CRCA powder coated white housing, CDL/Warm type illumination complete with all accessories required for connection complete all as specified and directed

S&F LED clean room bottom opening luminaire for hygenic facility, recessed mounted, size 2 ft x 2 ft, 34 watt, IP 65, slim (CDL), dust free, zero maintenance and connection complete all as specified and directed

S&F recessed mounted LED downlighter, round type, 15 watt, die cast aluminium, heat shrink and PC diffuser in white powder coated finish with integrated driver and connection complete all as specified and directed

S&F indoor decorative wall light fixture suitable for 10 W LED lamp, 230V for soft light ambiance, made up of polycarbonate, spiral B22 base lamp holder used, globe shape, incl LED lamp 10W complete all as directed

S&F flexible LED strip, uses high brightness as the light source for indoor application for cove lighting including LED driver for 24 watt in warm/ CDL, and connection complete all as specified and directed

S&F engagement light fitting with red & green colour lamp including connection complete all as specified and directed

S&F (at bldg/ periphery) energy saving security light fitting of 45 watts LED environmental friendly pressure die-cast aluminium IP 66 roadway luminaire with high power LED as light source comprising with electronic driver and all accessories pre-wired incl connecting up with PVC insulated copper conductor cable 1.5 Sqmm, 3 core as required for connections and 25 mm bore light grade GI tube mounting bracket of 1.5 meter in length, bend to shape as directed and fixed to wall by means of 02 nos. of 25 x 5 mm flat iron clamps, nuts, bolts and washers etc complete all as specified and directed

S&F High speed ceiling fan in white colour 1400mm sweep 220-240 volt, BEE 5 star rated with one set of 3 blades, down rod, hanger clamp PVC conopy and connection complete all as specified and directed

S&F ceiling fan 400mm sweep, cubid type with built in LED light and remote controll in white colour with connection incl necessary cutting in ceiling complete all as specified and directed

S&F wall mounted fan in white colour, 400mm sweep, AC, 230 volt, string operated and connection complete all as specified and directed

S&F exhaust fan 300mm dia, AC, single phase, 230/ 240 Volt, 900 RPM, metal body with louver shutter including frame, blades and connection complete all as specified and directed

M&L for concealed PVC conduit 20 mm dia, medium grade and conduit accessories and metal flush box of one module with conver fixed with screw and cap washers for Telephone/ LAN/ TV point etc all as specified and directed

M&L for concealed PVC conduit 25 mm dia, medium grade and conduit accessories and metal flush box of one module with conver fixed with screw and cap washers for Telephone/ LAN/ TV point etc all as specified and directed

M&L for modular type telephone socket out let (RJ11) with shutter incl flush mounting box complete all specified and directed

M&L for modular type LAN socket out let (RJ45) with shutter incl flush mounting box complete all specified and directed

M&L for modular type TV socket complete incl flush mounting box all specified and directed

M&L for for 0.60mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface/recessed PVC conduit/ race way etc complete all as required

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 240 sq mm 3.5 core complete all specified and directed

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core complete all specified and directed

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete all specified and directed

Taking down unserviceable PVC/ XLPE cable any size and removing from site complete all specified and directed

M&L for perforated type GI cable tray 600mmx40x40x2mm thick complete with all fittings all as specified and directed

M&L for perforated type GI cable tray 450mmx40x40x2mm thick complete with all fittings all as specified and directed

M&L for perforated type GI cable tray 300mmx40x40x2mm thick complete with all fittings all as specified and directed

M&L for perforated type GI cable tray 150mmx40x40x2mm thick complete with all fittings all as specified and directed

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick directly buried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of earth plate not less than 1.5m below the ground level connected to GI strip 32 x 6mm by means of bolts nuts check nuts and washers of galvanised iron at 2 points & GI pipe 40mm bore light grade for protection of earthing strip, PCC chamber 1:3:6 (type C-1) using 20mm graded stone aggregate, watering pipe 20mm bore light grade, funnel with wire mesh, 50 mm thick cover of RCC 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8 mm MS bars at 150 mm centre to centre both ways and charcoal dust and common salt all as shown in electrical plate No. 3 of MES SSR part-I and including excavation & earth work & connecting the earthing point/equipment and testing complete

M&L for earthing with Galvanised Steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using GI wire of size 4mm dia as earthing lead (upto the body of the equipment) by means of GI bolts, nuts, check nuts and washers and thimbles and protected by light grade 15mm dia GI pipe connected to main switch board or main control board and GI pipe medium grade 20mm bore for watering and including funnel, wire mesh, RCC pit cover and PCC chamber pit with PCC (1:3:6) type C-2 using 40mm graded stone aggregate, including excavation and earth work in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate No 5 of SSR 1991 (Part-I) complete

Supply, install, testing and commissioning of factory made LT panel of suitable size for following accessories,415 Volts outdoor type cubical compartmentalised vermin and water proof fabricated out of 3.15mm thick CRCA sheet powder coated front and back door openable with locking arrangement, necessary ventilation, including 400 Amps rated Aluminium bus bar for phases and 200 amp for neutral, insulated with PVC sleaves and coloured with (Red, Yellow, Blue and Black) CTR and internal wiring with suitable size of PVC insulated copper wire, use with angle iron 50x506mm frame bottom of the panel board, grouted by using PCC foundation 1:2:4 type C1 using with 20mm graded stone aggregate, thimbling and cable entry boxes with cable gland including painting with two coat of powder coated painting over a coat of red oxide primer incl taking down old one complete with following incoming/out going accessories:-

IN COMING

MCCB 4 Pole, 315 amp, 35 KA - 01 No

OUT GOINGS

(a) MCCB 4 Pole, 415 volts, 40 Amps 16 KA - 14 (12 + 2) Nos (Outgoing for lighting VTPN)

(d) Indicator lamp - One set of three

Supply, installation, testing and commissioning of factory made LT panel of suitable size, 415 Volts outdoor type cubical compartmentalised vermin and water proof fabricated out of 3.15mm thick CRCA sheet powder coated front and back door openable with locking arrangement, necessary ventilation, including 800 Amps rated Aluminium bus bar for phases and 400 amp for neutral, insulated with PVC sleaves and coloured with (Red, Yellow, Blue and Black) CTR and internal wiring with suitable size of PVC insulated copper wire, use with angle iron 50x506mm frame bottom of the panel board, grouted by using PCC foundation 1:2:4 type C1 using with 20mm graded stone aggregate, thimbling and cable entry boxes with cable gland including painting with two coat of powder coated painting over a coat of red oxide primer incl taking down old one complete with following incoming/out going accessories:-

IN COMING

(a) ACB 4 Pole, 415 V with Thermal Magnetic Release (Manual Drawout type) of capacity 630 Amps, 50 KA - 01 No

OUT GOINGS

(a) MCCB 4 Pole, 415 volts, 250 Amps 35 KA - 03 (02 + 01) Nos (Outgoing for AC / VRV outdoor system)

(b) MCCB 4 Pole, 415 volts, 63 Amps, 25 KA - 06 (04 + 02) Nos (Outgoing for Power/ AC units)

(e) Indicator lamp - One set of three

Supply and laying sub class 'B' bricks laid dry and flat across the length of cable for protection of cable complete

M & L for sand cushioning for protection of cable with screen wash river sand complete all as specified

M&L for GI tubing light grade with all necessary fittings laid in trenches/under road crossing/fixed on pole/wall/under floor including suitable mild steel FI clamps of required size complete all as specified & directed for following sizes:-

(a) 50 mm bore

(b) 80 mm bore

M&L for automatic Hand Dryer, plastic body, made of ABS material for ensure durability, corrosion proof, light weight, high speed, 1800 Watt, 220 Volts, 50 Hz, not less than 15 m/s wind speed, white in colour, dryies hand within 15-20 seconds, temperature of wind 60+/- 20 degree C incl connection complete all as specified and directed (Make :- Prestige/ Dolphy/ Zesta/ Elite)

S&F fresh air ventilating Fan 250 mm sweep, 230V, AC, plastic body with louver shutter incl necessary arrangement at wall/ window for fixing and connection complete all as specified and directed

M&L for 32 x 6 mm copper strip in short piece on surface or in recess for all interconnection/ for loop earthing etc as required complete all as specified and directed

M&L for earthing test point terminal block made out of gun metal or phosphour bronze of size 75 x 75 x 25 mm, drilled and screwed including 3 Nos 8mm dia 25mm long hexogonal head head screw fixed inside cubical shape enclosure made out of CRCA sheet 2 mm thick with front detachable cover, anodised screw, cap washer 4 Nos to be mounted on wall with wooded plug and screw 4 Nos duly painted inside and outside by two coats of aluminium paint over a coat of primer overall dimension of enclosure 200 x 150 x 100 mm (depth) complete all as specified and directed

M&L for 50mm dia heavy duty HDPE pipe PN1.0 alongwith fitting bends, caps etc fixed to wall, underground, ceiling or in floors for protection of copper/ aluminium strip of size 32 x 6mm for down conductor complete all as specified and directed

Note :- The contractor shall submit layout plan/ drawings duly marked with internal fittings and fixtures in BOQ (Schedule) for approval within 21 days from date of commencement.

Description of Work / Item(s)

Amount

Lawn work:- Korean grass : Digging of lwan, not less than 30 cms deep soil breaking of clads, removal of weeds and then levelling ( three times ) , supply and spreading of mannure bio fertillzer with sand and good soil incl pesticides mixing and again levelling and complete all as specified.

Trees Digging of pits, refilling with good quality soil mixed with mannure incl plantation of palm tree of height 8 feet and removal of surplus soil and complete all as specified.

Digging of pits, not less than 450x450x450 mm reffing with mannure bio fertilizer need based pesticides incl plantation of Aurocria plant complete as directed and complete all as specified.

Digging of pits, not less than 450x450x450 mm refiling with mannure bio fertilizer need based pesticides incl plantation of Ashoka trees complete as directed and complete all as specified.

Hedge Digging of pits, not less than300mm wide and 300 mm deep reffing with good quality soil with mannure need based pesticides and plantation of different hedges such as golden duranite and unimous along rear side, VIP entrance and frant lwan and removal and complete all as specified.

Flower beds Digging of pits, not less than300x300x300mm incl refilling with good soil mannure bio fertilizer etc and removal of surplus spoil and providing flowers of different breeds as required and complete all as specified.

Description of Work / Item(s)

Amount

Disconnecting electric connection, dismantling, taking down and shifting from COD Oval shed No 22 & 23 to GE (U) P&M store yard of EOT crane two ton capacity double girder type indoor of span 12.5 meter with web, height of crane 5 meter with connected accessories complete all as specfied and directed.

Disconnecting electric connection, dismantling, taking down and shifting from COD Oval shed No 22 & 23 to GE (U) P&M store yard of electric wire rope hoist with two ton capacity with mannual travel mechanism under ceiling on ISMB 300mm with connected accessories complete all as specfied and directed.

Description of Work / Item(s)

Amount

PART - A (HYDRANT SYSTEM) Supply, Installation , Testing & Commissioning of black Mild steel pipe (IS:1239 Part -I), heavy grade, C Class including cutting, welding and jointing with all fittings i.e tees, bends, elbows, flanges, reducers etc and providing anti corrosive treatment over the pipes by coating and wrapping the buried pipes with two layers of 4 mm thick,100mm wide anti corrosive tapes of approved makes as per IS :10221 all complete (Note : Earth work i.e. excavation, returning filling, removal of soil will be measured and paid seperately)

(a) 150 mm dia

(b) 100 mm dia

(c) 80mm dia

Supply, Installation, Testing & Commissioning of black Mild Steel pipe (IS:1239 Part -I) heavy grade, C Class including cutting, welding and jointing with all fittings i.e tees, bends, elbows, flanges, reducers etc.complete including painting of pipes with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade including fabrication of all M.S. structural steel work for clamping, supporting and hanging the pipes with MS rods and dash fasteners etc, all complete including cutting holes in brick or RCC walls / slabs and making good the same as directed (for internal exposed pipes in shafts/ ceiling) (a) 150 mm dia

(b) 100 mm dia

(c) 80 mm dia

(d) 50 mm dia

(e) 25 mm dia

Supply & fix fire hydrant gun metal landing valve type A (single head outlet) of 63 mm dia conforming to IS 5290

Supply and fix hose reel drum 36 mtr

Supply and fix 63 mm dia 15 meter long hose conforming to IS 636 complete with male and female coupling conforming to IS 903

Supply and fix 63 mm dia gun metal branch pipe with 12.5 mm nozzle conforming to IS 903

Supply and fix Gate valve of 25 mm dia

Providing & fixing M.S. fire hose door fabricated from 16 gauge M.S. sheet with full glass front door and locking arrangement, suitable to accommodate 1 Hydrant landing valve, 1 fire hose reel, 2 nos. 15 m long 63 mm dia hose, 1-branch pipe, The doors shall be painted with one coat of primer and finished stove enamelled finished in Fire Red and “Fire Hose” written on front including suitably mounted on a raised masonry platform as required. (Approx size 0.9m x 2.1m)

Supply and fix hand operated butterfly valve of pressure not less than 15 Kg / Sqcm with complete set (a) 150 mm dia

(b) 80 mm dia

Constructing masonry Chamber 120 x 90 x 100cm size in cement mortar 1:5 (1 cement : 5 fine sand) for sluice/butterfly valve, with C.I. surface box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement including necessary excavation and disposal of soil etc, complete as per standard design and as directed

Providing and fixing standard fireman's axe with heavy insulated rubber handle tested for 20 Kilowatts.

Providing & fixing Orifice plate made of 6mm thick brass or stainless steel with a plane central hole without burrs complete with identification tag projecting beyond flanges clearly stamped pipe dia and "K" factor of Orifice. (for checking the landing and yard hydrant/system pressure within permissible limits wherever required)

Supply and fix Pressure gauge 100 mm dia with ball valve of pressure 25 Kg/Sqcm

Supply and fix Automatic air release valve 50mm dia suitable for domestic water with 50mm gun metal stop valve complete (Note: All fire fighting hardware should be ISI marked. Pipes and supports will be painted with two coats of enamel paint over a coat of primer after surface preparation. Rate quoted should be inclusive of painting and pipe supports. All butterfly valves will have pad locking arrangement and cost of seven lever pad lock with universal key will be part of the valve nothing extra will be paid)

PART- B (HAND APPLIANCES) Supply and fixing of ISI marked (IS:940) Portable fire extinguisher, water expelling WCO2 type (gas pressure) type 9 litres with gunmetal cap. and nozzle, complete in all respects including initial fill and wall suspension bracket.

Supply and fixing of ISI marked (IS: 2878) Portable Fire Extinguisher, Carbon dioxide type of 4.5Kg capacity flat base including valve, discharge hose of not less than 10mm dia. 1m long and complete in all respect including initial fill with CO2 gas conforming to IS: 307-1966 filled to a filling ratio of not more than 0.667 and wall suspension bracket.

Supply and fixing of 5 Kg capacity ABC Type, Portable Fire Extinguisher, dry powder type (Gas Cartridge) with cylinder initially fully charged with dry powder, ISI marked confirming to IS: 13849 complete with standard discharge valve with tube, CI bracket for wall mounting.

Supply and fixing of 10 Kg capacity ABC Type, Portable Fire Extinguisher, dry powder type (Gas Cartridge) with cylinder initially fully charged with dry powder, ISI marked confirming to IS: 13849 complete with standard discharge valve with tube, CI bracket for wall mounting.

Supply and fixing of ISI marked (IS: 10204) portable fire extinguisher Mech. Foam type capacity 9 litres with gunmetal cap and nozzle and complete in all respects including initial fill and wall suspension.

Supply and fixing of ISI marked (IS 2171) Dry Chemical powder type fire extinguisher capacity 10 Kg with gunmetal cap and nozzle, delivery hose, ISI refill and gas cartridge, wall/trolley mounted and complete in all respects including initial fill.

PART - C (SPRINKLER SYSTEM) Providing, fixing, jointing, testing and commissioning M.S. pipe to I.S. 1239 (Heavy class) with fittings like, unions, couplings, bends, elbows, tees, offsets, reducers, flanges etc. Painted MS structural supports, hangers, fasteners etc. as directed complete the work as per the requirement at site including painting with two coats of synthetic enamel paint, over a coat of primer after surface preparation, cutting and making good the walls complete. Pipe upto 40 mm dia will be with threaded joints with malleable iron fitting conforming to IS: 1879 and 50 mm dia and above will be with butt welded joint including making connection for future extension along with plug. (a) 25 mm dia

(b) 32 mm dia

(c) 40 mm dia

(d) 50 mm dia

(e) 65 mm dia

(f) 80 mm dia

(g) 100 mm dia

(h) 150 mm dia

Providing, fixing, testing and commissioning M.S. pipe to I.S. 1239 (Medium duly) complete with all fittings like, unions, couplings, bends, elbows, tees, floor drains, offsets, reducers, flanges etc. to complete the work as per the requirement at site including painting with two coats of synthetic enamel paint, cutting and making good the walls good complete and including necessary clamps, MS support, fasteners. (for drain pipe ) (a) 80 mm dia

Supply and fix Bulb type gun metal sprinkler head set to operate at 68 degree C/ 79 degree C (a) Quick response Pendent Sprinkler 68 degrre C

(b) Upright type 68 degrre C

Providing, fixing, testing and commissioning 25mm dia gunmetal testing assembly with built in drain, valve, sight glass & connected to drain line complete in all respects.

Supply and fix flow switch (a) 150 mm dia

Supply and fix Automatic air release valve 50mm dia suitable for domestic water with 50mm gun metal stop valve complete

Supply and fix hand operated butterfly valve of pressure not less than 15 Kg / Sqcm with complete set (a) 150 mm dia

Supply and fix Pressure gauge 100 mm dia with ball valve of pressure 25 Kg/Sqcm

Sprinkler rossette 25mm dia complete all as specified and directed

Supply and fixing flexible pipe complete all as specified and directed (a) Sprinkler flexible type 1m

PART-D (Fire Pumps, Equipments, Piping, Valves & Accessories) Electric Motor Driven Pumps for Hydrant and Sprinkler System Installation, testing & commissioning of Electrical motor driven fire pump suitable for automatic/ manual operation consisting of the following for Hydrant and Sprinkler system :-

(i) Horizontal back pull single/ double stage centrifugal fire pump capable of delivering 2280 LPM against a total head of 70M and 2900 RPM complete with connection to suction and delivery line, and including bypass arrangement for testing of pumps and mechanical seal. Pump shall have a name plate indicating, head, discharge, stages, RPM and direction of rotation.

Pump shall be capable of handling not less than 150% of rated capacity at a head not less than 65 % of rated head. The shut off head shall not exceed 120% of rated head. HP of motor should be 20% more than the calculated HP.

(ii) Squirrel cage, induction motor, TEFC type suitable for 415 + 6%V, 3 phase, 50 Hz, AC supply, of suitable HP rating for the above pump with synchronous speed of 1450 RPM conforming to IP 55 protection & class 'F' insulation. The motor shall conform to IS 325 1978(up to date) with flexible coupling and coupling guard

(iii) Epoxy coated common base plate for mounting pump and motor fabricated of mild steel channel as per manufacturer's recommendation with required no. of heavy duty Anti Vibration pads.

(iv) Flexible Coupling and coupling guard for direct coupling of pump and motor.

(v) Drain Pipe (25 mm dia)

(vi) Technical Parameter Main Hydrant & Sprinkler Pumps.

(a) Flow rate/Discharge : 2280 LPM

(b) Pumping Head/ Pressure :-

Head - 70m

Motor HP - 80 HP (Approx.) or as per manufacturer recommendation

(c) Material of construction :-

(i) Casing - CI

(ii) Impeller - Phosphorous Bronze

(iii) Shaft - SS 304

(d) RPM - 2900 RPM

(e) Seat mechanical seal

Note :- Rate should be inclusive of foundation as per manufacturer's recommendations, bolts, vibration elimination pads etc complete.

Electrical Motor Driven Jockey Pump Installation, testing & commissioning of electrical motor driven Jockey pump suitable for automatic/manual operation consisting of the following:

(i) Horizontal multistage jockey pump with cast iron body, Bronze/S.S. impeller, stainless shaft with mechanical seal capable of delivering 180 LPM against total head of 70 M at 2900 RPM complete. The system shall be complete with pressure gauge with gun metal shut off cock on delivery side. The pump should meet the recommended requirement and must be approved by the local fire authority.

(ii) Squirrel cage induction motor suitable for 415 + 6%V, 3 phase, 50 Hz, AC supply of suitable HP rating for the above pump with synchronous speed of 2900 RPM T.E.F.C type connected to pump with flexible coupling and coupling guard .

(iii) Common base plate for mounting pump and motor fabricated of mild steel channel as per manufacturer's recommendation with heavy duty required Nos. Anti Vibration pads.

(iv) Suitable reinforced cement concrete pump foundations as per manufacturer's design including foundation bolts, nuts and washers as required.

(v) Drain pipe

(vi) Rate shall include inter connecting foundation bolts etc. complete.

(vii) Technical Parameter of Jockey Pump :

Jockey Pump :-

Flow rate/Discharge : 180 LPM

Pumping head: outlet-70 M head

Seat mechanical seal

Motor HP : 7.5HP (Approx.) or As per manufacturer recommendation

Note :- Rate should be inclusive of foundation as per manufacturer's recommendations, bolts, vibration elimination pads etc complete.

Supply and fix Mild Steel class 'C' diesel pump exhaust pipe 150mm dia with one layer of 10mm thick asbestos rope insulation and including all fitting clamp/ structural steel supports complete

Supply and fix Air vessel for Fire Pump, 300mm dia 2m height (Note : Contractor should submit general arrangement drawings before fabrication of vessel and ultrosonic test report to be submitted on supply of vessel)

Supply and fix Pressure gauge 100 mm dia with ball valve of pressure 25 Kg/Sqcm

Providing & fixing and painting black steel pipes to I.S. 3589(6.35 mm thick) or IS 1239 heavy class including all fittings, like, fasteners, structural supports, clamps, couplings, bends, elbows, tees,offsets etc. welded or flanged joints as required, painting as per specifications, cutting holes and chases in brick or RCC walls and making good complete for pump suction and delivery piping. (a) 50 mm dia

(b) 65 mm dia

(c) 80 mm dia

(d) 150mm dia

(e) 200mm dia (6.35mm thick)

(f) 250mm dia (6.35mm thick)

(g) 300mm dia (6.35mm thick)

Providing and fixing CI double flanges suction strainer (PN 1.0) “Y” type including, nuts, bolts and 3mm thick rubber insertion complete of size 250mm all as directed

Providing and fixing resilient rubber lined neoprene single arch vibration eliminators with unit control suitable for fire pump upto 45 deg C. Temperature working pressure 16 Kg per square centimeter complete (a) 80 mm dia

(b) 100 mm dia

(c) 150 mm dia

(d) 200 mm dia

Supply and fix Automatic air release valve 50mm dia suitable for domestic water with 50mm gun metal stop valve complete

Supply and fix hand operated butterfly valve of pressure not less than 15 Kg / Sqcm with complete set (a) 50 mm dia

(b) 65 mm dia

(c) 80 mm dia

(d) 100 mm dia

(e) 150 mm dia

(f) 200 mm dia

(g) 250 mm dia gear operated

Supply and fix Non Return butterfly Valve (a) 80 mm dia

(b) 100 mm dia

(c) 150 mm dia

(d) 200 mm dia

S&F ICV / Alarm gong (Intermittent hydraulic alarm with alarm gang and water motor Alarm) 150mm complete

Providing, making and writing legend, arrow making with sythetic enamel paint on G.I/ M.S Pipes, Pressure Vessel, pump in pump room, shaft and terrace level complete including surface preparation and as directed

Supply, installation, testing and commissioning of factory made LT panel of suitable size, floor mounted for Fire Pumps panel board CPRI approved,415 Volts outdoor type, cubical compartmentalised vermin and water proof fabricated out of 3.15mm thick CRCA sheet, front and back door openable with locking arrangement, necessary ventilation, internal wiring with suitable size of PVC insulated copper wire, panel to be grouted at PCC foundation 1:2:4 type C1 using with 20mm graded stone aggregate, thimbling and cable entry boxes with cable gland including painting with two coat of powder coated painting over a coat of red oxide primer complete with following accessories:-

(a) 4 Nos bus bars of high conductivity aluminium alloy, 3 Nos for phase (R,Y,B) rating 300 amp rating and 1 No for neutral rating 150 amp, mounted on DMC support with heat shrink sleeve - 01 set.

(b) MCCB 4 Pole, 415 volts, 250 Amps 35 KA - 01 No (Incoming)

(c) MCCB 4 Pole, 415 volts, 160 Amps 25 KA - 02 (Outgoing for Fire Pumps)

(d) MCCB 4 Pole, 415 volts 40 Amps 25 KA-03 (Outgoing 02 for Jockey Pumps & 01 for booster pump)

(e) Star Delta fully automatic Starter suitable for upto 80 HP fire pumps including suitable rating of 4 pole contactors (Main & Delta), 415 Volt (Make Seimens/ L&T/ C&S) - 02 Nos

(f) Star Delta fully automatic Starter suitable for upto 7.5 HP including suitable rating of 4 pole contactors (Main & Delta), 415 Volt (Make Seimens/ L&T/ C&S) - 02 Nos

(f) DOL Starter suitable for upto 5 HP including suitable rating of 4 pole contactors (Main & Delta), 415 Volt (Make Seimens/ L&T/ C&S) - 01 No (for Booster pump)

(g) Single phase preventor - 05 Nos

(h) Overload relay of suitable rating - 05 Nos

(j) Voltmeter, three phase, digital type, suitable for range (0-500) volts with selcetor switch - 01 No.

(k) Ammeter, digital type, three phase, (0-300 amp) with suitable CT's complete - 01 Set

(l) Indication lamp (R,Y,B), LED type, with toggle switches - 03 Set.

(m) Other connected accessories such as push buttons start/ stop etc as required

(n) Grouting of panel including PCC

Note :- (a) Operation of electrically operated Jockey pump should frequent start/ stop to operate in pressure falls below not less than 6 Kg/ Cm2 in hydrant system with electrical/ mechanical connection incl accessories etc as required incl wiring with PVC FRLS copper wiring cable 1100 V grade of suitable size complete. (b) Layout design of LT panel shall be submitted by the contractor to GE for approval before procurement.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sq mm 3.5 core complete all as specified and directed

M&L for PVC FRLS copper cable 1100 volts grade single core 10 sqmm, unsheathed from panel to pumps laid in UPVC pipe 40mm bore with suitable size copper thimbles for both ends of wire complete (Note : Three runs of single core copper wire incl UPVC pipe will be measured as one RM) (For Jockey Pump)

M&L for PVC FRLS copper cable 1100 volts grade single core 35 sqmm, unsheathed from panel to pumps laid in UPVC pipe 40mm bore with suitable size copper thimbles for both ends of wire complete (Note : Three runs of single core copper wire incl UPVC pipe will be measured as one RM) (For Fire Pumps)

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick directly buried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of earth plate not less than 1.5m below the ground level connected to GI strip 32 x 6mm by means of bolts nuts check nuts and washers of galvanised iron at 2 points & GI pipe 15 mm bore light grade for protection of earthing wire PCC chamber 1:3:6 (type C-1) using 20mm graded stone aggregate, watering pipe 20mm bore light grade, funnel with wire mesh, 50 mm thick cover of RCC 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8 mm MS bars at 150 mm centre to centre both ways and charcoal dust and common salt all as shown in electrical plate No. 3 of MES SSR part-I and including excavation & earth work & connecting the earthing point/equipment and testing complete all as specified and directed

Providing and fixing 100 mm dia Bourdon type pressure gauge with gun metal isolation cock and copper 'U' Tube complete

Supply, installation, testing and commissioning of pressure switches (INDFOSS IPS 100 or approved equivalent) including making connections with the control panel and the pressure vessel including control cabling wk complete in all respects all aspecified and directed

Providing and fixing full bore type brass ball valve with chrome plated, teflon seating and ring, full bore type with lever and screwed female ends suitable for working pressure of 25 kg/sq.cm. as per IS 12992 complete for the following sizes :- (a) 15mm

Providing and fixing fire brigade suction hose coupling (draw out connection) with nut for female coupling as per I.S:902-1974 complete with 100mm dia. suction pipe and foot valve (To be connected to static tank) complete all as specified and directed

M&L for Automatic Addressable Relay module for AHU & Stair Pressurization fan, The Module shall have automatic Electronic addressing feature & each of these shall be equipped with fault Isolator complete with the GI Mounting Box and the hardware etc as required (UL/ EN approved) complete all as specified and directed

M&L for Automatic Analog addressable Multicriteria detector with mounting Base, the Detector's Alarm LED shall be viewable from 360 Degree, the Detector shall have automatic electronic addressing feature & each of these shall be equipped with fault Isolator complete with the GI Mounting Box and the hardware etc as required (UL/ EN approved) complete all specified and directed

M&L for Automatic Analog addressable Multicriteria detector with mounting Base. The Detector shall have automatic Electronic addressing feature & each of these shall be equipped with fault Isolator complete with the GI Mounting Box and the hardware etc as required (UL/ EN approved) complete all specified and directed

M&L for Addressable Manual call Station, the Call Point shall have automatic electronic addressing feature & each of these shall be equipped with fault Isolator complete with the Mounting Box and the hardware etc as required (UL/ EN approved) complete all as specified and directed

M&L for Electronic Sounder cum strobe unit, the sounder shall have automatic electronic addressing feature & each of these shall be equipped with fault Isolator complete with the mounting box and the hardware etc as required (UL / EN Approved) complete all as specified and directed

M&L for Dual LED Response indicator for indicating the activation of the Remotely located Detector complete all as specified and directed

M&L for FIRE EXIT Signage with LED and battery back up and charger with hanging arrangement complete all specified and directed (Make - Omniexit/ ETON/ Heinrich)

M&L for 25mm MS conduit with all accessories complete all as specified and directed

M&L for 2 x 1.5 Sqmm FRLS unarmoured copper conductor cable complete all specified and directed

M&L for 2 x 1.5 Sqmm FRLS armoured copper conductor cable complete all specified and directed

PART-F (WATER STORAGE TANK FOR FIRE FIGHTING PROTECTION) Design, supply, installation & testing of Prefabricated bolted water storage tank of capacity 1 Lakh Ltr, MOC- Zinc Alume /Galvalume sheets, above ground of the following specifications including foundation as per manufacturer's design complete all as specified and directed (Make :- Arsenol Steels Silos/ Rostfrei Steels or equivant as approved):-

(i) Tank Design Parameters :-

(a) Design Life : 40 - 50 Years

(b) For wind Velocity : Average 175 KM / Hr

(c) Seismic Zone : UBC 4

(d) Specific Gravity : 1

(e) Dimension of Tank :- Diameter - 5.72 Mtr, Height - 4.20 Mtr : Gross Volume 1,07,873 L

(f) Effective capacity : 1,00,167 L

(g) Temperture range : -20 to +60 Deg C

(h) Colour : Natural Zinc Alume

(ii) Tank Wall

(a) Type : Bolted, Panelled, Linear Tanks

(b) Shape : Cylindrical

(c) MOC of Tank Sheets : Zinc Alume / Galvalume

(d) Composition of coating : Al - 55%; Zn - 43.5%; Si - 1.5%

(e) Coating Thickness : 150 GSM

(f) Colour of Sheets : Natural Zinc Alume Colour

(g) Thickness of wall sheets : Minimum 0.8mm of one sheet and more in multiple as per structural load

(h) Mechanical Properties of Sheet : Yield Strength : 300 Mpa, Tensile Strength : 340 Mpa

(j) Sheet Dimension : 3200 mm X 1120 mm

(k) Sheet Corrugation : Pitch 75 mm; Depth - 18 mm

(l) Wall Sheet Tensile Strength : 340 Mpa

(iii) Roof Sheet

(a) MOC of Roof Sheet : Zinc Alume / Galvalume

(b) Thickness of Roof Sheet : 0.5mm (TFT)

(c) Load Bearing Capacity of Roof : 110 Kg/Sqmtr

(d) Roof Sheet Tensile Strength : 550 Mpa

(e) Colour of Sheets :- Natural Zinc Colour

(f) MOC of trusses for roofing : MS-Hot dipped galvanized - 500-600 GSM

(g) Size of Trusses for roofing : As per design

(iv) Tank Liner

(a) MOC of Liner : Reinforced PVC, UV Stabilized, Anti Algae

(b) Thickness of Liner : PVC - 760 GSM

(c) Liner Strength : As per Product datasheet

(d) Water Proofness Test : 220 PSI for PVC

(e) Methods adopted for liner manufacturing and Testing :- For Manufacturing : Leisture PVC welding machine, For Testing : Visual Inspection/ Light test

(f) Liner Life : Same as tank

(g) Bottom Protection of Liner : Geo Textile

(h) Thickness of Geo Textile : 3 mm compressed

(v) Nozzle

(a) MOC : MS Hot Dipped galvanized Iron

(b) Nozzle Schedule ; BS table - 10 D/E

(c) Nozzle size and quantity : 5 Nozzles with maximum size od 150 mm

(vi) Nuts & Bolts

(a) MOC : Hot Dipped galvanized Iron

(b) Grade : M-10 Grade 8.8 (10 mm)

(c) Protection of nuts from Atmosphere : PVC/ Silicon Caps from outside

(vi) Anchor Fasteners

(a) MOC : Galvanized Iron

(b) Type : Mechanical (type)

(c) Size : 16x200/ 16x250/ 20 x 300 (as per tank size)

(vii) Tank Accessories Standard

(a) Ladder - Outside : External straight cage ladder with cage starting at 2m height

(b) Internal ladder : Nylon Rope Ladder with Aluminium steps

(c) Air Vent : Turbine Vent (SS-304/ Aluminium) - 200 mm size. OR PVC U-Vent. (with roof tank only)

(d) MOC Access hatch on Dome roof along with Platform : Zincalume with Lockable Lid (600mm x 600mm)

Note Fire Hydrant, Sprinkler system, Fire Alarm system and Fire water tank :- The contractor shall submit layout plan/ drawings duly marked items included in BOQ (Schedule) for approval within 21 days from date of commencement.

Bansal Infratech Synergies India Ltd

M P TYAGI ENGINEERS AND CONTRACTORS

mahinder pal and co

City Promoter and Buildwell Pvt. Ltd.

Chauhan Associates

AMIT ASSOCIATES

SHIVALAYA CONSTRUCTION CO. PVT LTD

mahinder pal and co

AMIT ASSOCIATES

City Promoter and Buildwell Pvt. Ltd.

Bansal Infratech Synergies India Ltd

SHIVALAYA CONSTRUCTION CO. PVT LTD

M P TYAGI ENGINEERS AND CONTRACTORS

Chauhan Associates

AMIT ASSOCIATES

Chauhan Associates

City Promoter and Buildwell Pvt. Ltd.

mahinder pal and co

M P TYAGI ENGINEERS AND CONTRACTORS

SHIVALAYA CONSTRUCTION CO. PVT LTD

N A Construction Pvt Ltd

mahinder pal and co

City Promoter and Buildwell Pvt. Ltd.

SHIVALAYA CONSTRUCTION CO. PVT LTD

AMIT ASSOCIATES

M P TYAGI ENGINEERS AND CONTRACTORS

Chauhan Associates

N A Construction Pvt Ltd

City Promoter and Buildwell Pvt. Ltd.

Chauhan Associates

SHIVALAYA CONSTRUCTION CO. PVT LTD

AMIT ASSOCIATES

mahinder pal and co

M P TYAGI ENGINEERS AND CONTRACTORS

N A Construction Pvt Ltd

Bansal Infratech Synergies India Ltd

mahinder pal and co

City Promoter and Buildwell Pvt. Ltd.

Chauhan Associates

SHIVALAYA CONSTRUCTION CO. PVT LTD

AMIT ASSOCIATES

M P TYAGI ENGINEERS AND CONTRACTORS

Chauhan Associates

mahinder pal and co

City Promoter and Buildwell Pvt. Ltd.

N A Construction Pvt Ltd

M P TYAGI ENGINEERS AND CONTRACTORS

AMIT ASSOCIATES

SHIVALAYA CONSTRUCTION CO. PVT LTD

mahinder pal and co

Chauhan Associates

City Promoter and Buildwell Pvt. Ltd.

AMIT ASSOCIATES

SHIVALAYA CONSTRUCTION CO. PVT LTD

Bansal Infratech Synergies India Ltd

N A Construction Pvt Ltd

mahinder pal and co

Chauhan Associates

M P TYAGI ENGINEERS AND CONTRACTORS

AMIT ASSOCIATES

N A Construction Pvt Ltd

City Promoter and Buildwell Pvt. Ltd.

SHIVALAYA CONSTRUCTION CO. PVT LTD

AMIT ASSOCIATES

Bansal Infratech Synergies India Ltd

mahinder pal and co

N A Construction Pvt Ltd

M P TYAGI ENGINEERS AND CONTRACTORS

City Promoter and Buildwell Pvt. Ltd.

SHIVALAYA CONSTRUCTION CO. PVT LTD

AMIT ASSOCIATES

City Promoter and Buildwell Pvt. Ltd.

M P TYAGI ENGINEERS AND CONTRACTORS

SHIVALAYA CONSTRUCTION CO. PVT LTD

N A Construction Pvt Ltd

Chauhan Associates

Bansal Infratech Synergies India Ltd

AMIT ASSOCIATES

M P TYAGI ENGINEERS AND CONTRACTORS

Chauhan Associates

City Promoter and Buildwell Pvt. Ltd.

SHIVALAYA CONSTRUCTION CO. PVT LTD

N A Construction Pvt Ltd

Bansal Infratech Synergies India Ltd

mahinder pal and co

City Promoter and Buildwell Pvt. Ltd.

SHIVALAYA CONSTRUCTION CO. PVT LTD

Chauhan Associates

Bansal Infratech Synergies India Ltd

M P TYAGI ENGINEERS AND CONTRACTORS

N A Construction Pvt Ltd

mahinder pal and co

Chauhan Associates

City Promoter and Buildwell Pvt. Ltd.

AMIT ASSOCIATES

N A Construction Pvt Ltd

M P TYAGI ENGINEERS AND CONTRACTORS

SHIVALAYA CONSTRUCTION CO. PVT LTD

Chauhan Associates

M P TYAGI ENGINEERS AND CONTRACTORS

AMIT ASSOCIATES

City Promoter and Buildwell Pvt. Ltd.

N A Construction Pvt Ltd

SHIVALAYA CONSTRUCTION CO. PVT LTD

Bansal Infratech Synergies India Ltd

mahinder pal and co

AMIT ASSOCIATES

M P TYAGI ENGINEERS AND CONTRACTORS

City Promoter and Buildwell Pvt. Ltd.

Chauhan Associates

SHIVALAYA CONSTRUCTION CO. PVT LTD

Bansal Infratech Synergies India Ltd

mahinder pal and co

M P TYAGI ENGINEERS AND CONTRACTORS

AMIT ASSOCIATES

Chauhan Associates

Bansal Infratech Synergies India Ltd

City Promoter and Buildwell Pvt. Ltd.

SHIVALAYA CONSTRUCTION CO. PVT LTD