Loading…
Loading…
Tender Value
₹39.5 Cr
EMD Value
₹79.0 L
Closing Date
7 Oct 2026, 3:00 pm
Yes (up to 3 members)
No
Two Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
90 days
Expenditure
Capital (Works)
DRM WA
15 conditions · 4 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or V whichever less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a)(a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work each costing not less than the amount equal to 60% of advertised value of the tender. (b)(b) (i)In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note: for b (i) separate completed works of minimum required values shall also be considered for fulfilment of technical eligibility criteria for different components. (b)(ii)In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (iii) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contract or through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing.
However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing. Note for Item 10.1: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Similar Nature of work: - Any Civil Engineering work.
3 conditions · 1 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
MOU Clause for waterproofing - The contractor shall submit copy of MOU on non-judicial stamp paper of Rs. 100 with any specialist agency who is approved applicator of FOSROC, SIKA, PAGEL, IZONIL or Equivalent from which he proposes to carry out the work of Schedule "C" item No. -1/NS, item No. -2/NS, item No. -3/NS, item No. -4/NS, item No. -5/NS, item No. -6/NS, item No. -7/NS, item No. -8/NS, item No. -9/NS, item No. -10/NS, item No. -11/NS & item No. -12/NS pertaining to waterproofing treatments of RUB with all connected items of Sch "C" along with other relevant documents for opening of technical Bid (cover I). Such specialist agencies should have valid applicator certificates from the manufacturers issued not older than 90 days from the bid submission start date of tender. Without submission of copy of MOU, the contractor shall not be allowed to take up the work under waterproofing related items. Note: - Non submission of above MEMORANDUM OF UNDERTAKING by the tenderer's shall result in summarily rejection of his/their tender. ( Click here to download Format)
Provision of cover shed, sump, extension and raising of retaining wall, sealing of joints, road surfacing etc and other improvement relate works at various RUB's/LHS's under the jurisdiction of ADEN-RGS Section.
ENGG-JP-2026-27-105~NWR
ENGG-JP-2026-27-105
Open
Works - General
8 Months
Jaipur, Rajasthan
₹0
₹79.0 L
10 Sept 2026
10 Sept 2026
23 Sept 2026
41 items across 2 schedules · ₹10,09,36,978 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil. | cum | 400 | 260.3 | 1,04,120 |
| 2 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 200 | 6,812 | 13,62,400 |
| 3 | 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 300 | 9,895.2 | 29,68,560 |
| 4 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 108000 | 133.7 | 1,44,39,600 |
| 5 | Hot finished welded type tubes | Kg | 1080000 | 194.4 | 20,99,52,000 |
| 6 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. | Kg | 66150 | 97.2 | 64,29,780 |
| 7 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | Kg | 108000 | 172.6 | 1,86,40,800 |
| 8 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 45000 | 738.65 | 3,32,39,250 |
| 9 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) | cum | 850 | 2,434.25 | 20,69,112.5 |
| 10 | Nominal concrete 1:4:8 or leaner mix (including equivalent design mix) | cum | 850 | 1,503.6 | 12,78,060 |
| 11 | 90 mm to 45 mm size stone aggregate | cum | 40 | 2,098.4 | 83,936 |
| 12 | 63 mm to 45 mm size stone aggregate | cum | 40 | 1,636.05 | 65,442 |
| 13 | Moorum | cum | 18 | 768.25 | 13,828.5 |
| 14 | Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . | cum | 78 | 1,046.95 | 81,662.1 |
| 15 | Cement concrete prepared with batch mixing machine | cum | 1500 | 10,529.35 | 1,57,94,025 |
| 16 | 600 mm dia RCC pipes. | Metre | 200 | 3,401.25 | 6,80,250 |
| 17 | Serrated with central bulb (225 mm wide, 8- 11 mm thick) | Metre | 750 | 327.65 | 2,45,737.5 |
| 18 | 300 mm dia | Metre | 2700 | 707.75 | 19,10,925 |
| 19 | 300 mm dia | Metre | 620 | 825.7 | 5,11,934 |
| 20 | 200 mm nominal size dia having minimum wall thickness 5.40 mm | Metre | 2625 | 2,442.75 | 64,12,218.75 |
| 21 | Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make | Sqm | 900 | 285.2 | 2,56,680 |
| 22 | Stirrer mixed Acrylic Polymer of approved make @ 2% of weight of cement used) modified Cement slurry made with non shrink compound in concrete/RCC work | Kg | 900 | 119.3 | 1,07,370 |
| 23 | 25 mm thick in Grade M25 with cement content not less than 330 kg per cum | Sqm | 900 | 746.9 | 6,72,210 |
| 24 | 50 mm thick in Grade M25 with cement content not less than 330 kg per cum | Sqm | 900 | 1,151.05 | 10,35,945 |
| 25 | Providing and inserting 12 mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diametre (20 mm to 30 mm) up to depth from 30 mm to 80 mm at required spacing and making the hole & crack dust free by blowing compressed air, sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-In-Charge. | Each | 500 | 236.9 | 1,18,450 |
| 26 | Providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of "L" shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by Engineer-in-charge. | Sqm | 900 | 902.55 | 8,12,295 |
| 27 | Sealant 25 mmx10 mm at joints | Metre | 900 | 178.95 | 1,61,055 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
2026-27-105.pdf
ATTACHMENT
GCC-2022-ACS10.pdf
ATTACHMENT
GCC2022correctionslipsupto12.pdf
ATTACHMENT
CableCutletterofHQ_compressed1.pdf cable cut latter
ATTACHMENT
Financialbid105.pdf
ATTACHMENT
Memorandumofundertaking105.pdf
ATTACHMENT
Technicalbid105_1.pdf
ATTACHMENT
CableCutletterofHQ_compressed1.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .