SPECIAL REPAIRS TO SWIMMING POOL (BUILDING NO P-28) AT BAITHKOL AREA, NAVAL BASE KARWAR AND PROVN OF INTERLOCKING TILES AND REPLACEMENT OF TILES WITH VITRIFIED TILES AT GROUND FLOOR HQKNA BUILDING AT NAVAL BASE KARWAR.

Amount

Demolition of cement concrete (unreinforced) of any description and any position all as specified and directed.

Demolition of cement concrete (reinforced) of any description and any position all as specified and directed.

Taking down of chowkat / frames with shutter (w/o taking off shutter from frames) n.exc 1.5 Sqm each (Distrubed surface of wall shall be make good by the contractor. The rate quoted shall be deemed included for the same)

All as per item No:03 here-in-before but exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

Demolition of Brick stone/boulder masonry built in CM, complete all as specified and directed.

Dismantling of PVC/ RCC water storage tank of capacity exceeding 500 litre but not exceeding 1000 litre, including removal of rubbish outside MoD land, complete all as specified.

Taking down cement plaster from wall surfaces of any description etc including racking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking and binding with and including mild steel wire (annealed) not lessthan 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 08 here-in-before but 6mm to 8mm dia complete all as specified.

M&L for Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) aggregatein Walls, retaining walls, basementwalls, ballast walls and the like;any thickness; above top of footings; including attached plaster and buttresses complete all as specified.

M&L for Providing precast cement concrete solid building blocks masonry exc 10cm width, type C1,1:3:6 (20mm graded aggregate) set in cement mortar 1:6 complete all as specified and directed.

M & L for rendering 15 mm thick in CM (1:6) on fair faces of block masonry or concrete surfaces finished even an smooth without using extra cement all as specified and directed.

M & L for rendering 15 mm thick in CM (1:4) on fair faces of block masonry or concrete surfaces and finished even and smooth without using extra cement and mixed with water proofing compound @ 3% by weight of cement all as specified and directed.

M & L for rendering 10 mm thick in CM 1:3 on ceiling surfaces finished even an smooth without using extra cement all as specified and directed.

Supply only Integral water proofing compound complete all as specified and directed.

M&L for preparation of new plastered / decorated wall surfaces including appyling a coat of 1mm thick wall care putty on new surfaces and Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work including necessary safety measures as required etc complete all as specified and as directed by Engr-in-Charge.

M & L for preparing newly plastered surfaces of ceiling and applying two coats of acrylic washable distemper over a coat of primer all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces etc complete all as specified and as directed by Engr-in-Charge.

M & L for wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown bitumen of any penetration applied hot @ 1.7 Kg per Sqm blended with grit or pea size gravel @ 0.006 Cum per Sqm, and lightly tampered (area of flashings etc., shall be added to the roof area) complete all as specified and directed by Engr-in-Charge.

M & L for providing cement concrete in roof kerbs of mud stops, rounded or chamfered on edges type C1 1:3:6 using 20 mm graded crushed stone aggregate complete all as specified and directed.

M & L for providing 15 mm thick rendering over roof slab when concrete is green in CM 1:3 mixed with water proofing compound @ 3% by weight of cement, finished even and smooth surface without using extra cement all as specified and directed.

S&F APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. Not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed.

S&F for aluminium powder coated (minimum thickness of powder coated 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F aluminium powder coated (minimum thickness of powder coated 50 micron) window/ventilator shutters, sliding type without sash bars, aluminium sections weighing not less than 0.55kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, aluminium snap beading, screws etc compelte all as specified and directed.

S&F aluminium powder coated Anodised aluminium door shutters(Thickness or powder coating not less than 50 micron),aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified and directed.

S&F Aluminium grills of DG 104(10mm) powder coated of make Decogrill or equivalent including dismantling of old unserviceable alumunium grill all as specified and directed.

S & F in repairs aluminum alloy wire cloth, 0.45 mm nominal dia of wire & average width of aperture 1.4 mm and fixed with wire staples all as specified and directed.

M & L for 4 mm thick sheet glass, ordinary quality and glazing with wooden beading not exc 0.5 Sqm in each pane all as specified and directed.

S & F in repairs aluminium die cast body door closer hydraulically regulated designation No-3 universal type suitable for door shutters of 85 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified and directed.

M & L for 4 mm thick figured glass, pin head type and glazing with wooden beading, not exc 0.5 Sqm in each pane all as specified and directed.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made all as specified and directed by Engr-in-Charge.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F in repairs Butt hinges 100 mm, cast brass,with mild steel hinge pin, bright polished and fixed, typeB-11 complete all as specified and directed

S&F in repairs Butt hinges 125 mm, cast brass,with mild steel hinge pin, bright polished and fixed, but type C-22 complete all as specified and directed

S & F in repairs Aluminium anodised, barrel tower bolts 200 mm long of extruded section and fixed all as specifed and directed.

S & F in repairs Aluminium anodised barrel tower bolts of extruded section 150 mm long all as specifed and directed.

S & F in repairs Aluminum alloy, sliding door bolt 300 mm long and not less than 12 mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and directed.

S&F in repairs extruded aluminium handles, fabricated type 100mm size all as specified and directed.

S&F in repairs extruded aluminium handles, fabricated type 150mm size powder coated all as specified and directed.

S & F floor door stopper of aluminum alloy body and tongue, anodised with hard drawn steel spring and vulcanised rubber piece fixed in floor, overall length of cover plate 140 mm all as specified and directed.

M&L for applying one coat of Acrylic washable distemper on old decorated surfaces of wall including preparation of old surfaces including necessary safety measures as required etc complete all as specified and directed.

M&L for applying one coat of Acrylic washable distemper on old decorated surfaces of ceiling including preparation of old surfaces including necessary scafolding and safety measures as required all as specified and directed.

M&L preparing of old painted plastered surface of walls of any description including cornices and applying one coats of acrylic emulsion exterior grade, weather proof antifungal paint including necessary scafolding and safety measures as required complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

Dismantling floor, hearth or wall tiling manual means only to avoid any damage to mother structure including cement mortar bedding (but not backing), removing serviceable tiles to store and removing all the rubbish as directed by Engineer-in-charge complete all as specified and directed.

Material and labour for water proofing treatment including equipments and supervision charges in following step by step procedure:- (a) Clean the surface thoroughly to make it smooth and free of any foreign material. (b) Coving will be done at vertical horizontal joint using Polymerized Cement mortar of 1:4 admixed with Advanced latex plus. (c) Joint treatment will be done with Polymerized Cement mortar of 1:4 admixed with Advanced latex plus. (d) Bore packing shall be done with Super Grout for the pipe penetration. (e) Water pond test for Mother slab to identify the leakages points before starting the waterproofing work. (f) Injection grouting, if required should be done for all leakage point identified and inject the cement slurry admixed with injection grout admixture HS Super Grout Admix, or equivalent using pressure grouting machine till the rejection of material from the nozzle.

(g) Prepared HS ShaliCem EWP / SBR Latex (Sika) / liquithane EMA(IWL) / Nitobond SBR(Fosroc) or equivalent Form Theire respective Methods For Application . (h) Application of one coat of HS ShaliCem EWP/ SBR Latex (Sika) / liquithane EMA(IWL) / Nitobond SBR(Fosroc) or equivalent over all the corners between the floor and wall joints. (i) Allow it to dry for 6 -8 hours. (j) Apply the 2nd coat of ShaliCem EWP over the 1st coat after mixing component 1 and component 2 at 1:2 ratio. (k) Protect Horizontal surface with 50 mm PCC admixed with HS Cement / SBR Latex (Sika) / liquithane EMA(IWL) / Nitobond SBR(Fosroc) or equivalent Mix Plus @ 200ml/bag to the required slope. (l) Protect Vertical surface with Polymer Modified Mortar of 1:4 prepared with Advanced Latex Plus Note: (i) The work should be carried out by authorized applicator of manufacture only.

M&L for screed bed for horizontal surface with 50 mm average thickness and plaster the vertical waterproof surface with average thickness of 12 to 15 mm in CM 1:4 . Add HS cement Mix Plus towards water resistance (150 ml per bag) completely as per specification and directed by Engineer-in-Charge.

Material and Labour for Blue crystal Mosaic walls/ floor tiles of 6-8 mm thick swimming pool tiles of area not exc 0.18 Sqm fixed using high performance polyurethane epoxy based adhesive Nitotile GPX(Fosroc)/NITOTILE MPA or equivalent Note: (a)Spacer shall be provided between the tiles and quoted rate is inclusive of the same. (ii) Joint of tiles shall be filling with using Nitotile EPW(Fosroc) or equivalent on floor and walls whichever is applicable all complete as per the manufactures instructions quoted rate is inclusive of the same. Make- HR JHONSON / Kajaria / ORIENTBELL / AGL or equivalent as listed in CA.

M & L for non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exc 0.11 Sqm but not exc 0.18 Sqm in floor etc laid over and including 15 mm thick screed bed in CM 1:4 set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

M & L for glazed ceramic coloured tiles in vertical surfaces 300 x 450 x 7 mm thick over and including 10 mm thick cement plaster in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

S & F in repair vitreous china wash basin, white, flat back size 550 x 400 mm white excluding taps, waste coupling and pipe but including brackets all as specified and directed.

S&F in repairs vitreous china wash down water closet (pedestal pattern) white,with plastic water closet seat & back with flat bottom and cover including fixing bolts and necessary connection with existing pipes etc complete all as specified and directed.

S & F in repairs PVC valveless, syphonic action type, low level flushing cistern 10 ltr capacity, white colour with inlet ball valve, float, handle including brackets etc complete all as specified and directed.

S&F in repairs 32 mm bore PVC waste pipe with fittings of approved make suitable for WHB, Urinals etc all as specified and directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S & F in repairs Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) all as specified and directed.

S & F in repairs stop valves/ angle valve, cast copper alloy fancy type chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe of 15 mm bore all as specified and directed.

S & F in repairs bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe 15 mm bore complete all as specified and directed.

S & F in repairs pillar taps cast copper alloy, fancy type, chromium plated with capstan heads screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe of 15 mm bore of complete all as specified and directed.

S & F in repairs brass CP shower rose 125 mm size with swivel joints any size including to steel pipe or union complete all as specified and directed.

S & F PVC connection 15 mm size with PTMT nuts of length 600 mm long all as specified and directed.

S & F in repairs 15 mm dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe for wall and fixed complete all as specified and directed.

S & F in repairs chromium plated toilet paper holder fancy type fixed to wall with chromium plated brass screw complete all as specified ans directed.

S & F in repairs Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats Minimum weight 90gms all as specified and directed.

S & F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws all as specified and directed. MAKE: Jaquar Cat No. CAN 1131N or equivalent in makes as specified here-in-after.

Taking up or down GI tubing 15 mm bore and connections all as specified and directed.

Taking up or down GI tubing 20 mm bore and connections all as specified and directed.

Taking up or down GI tubing 25 mm bore and connections all as specified and directed.

S & F 16 mm dia Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S & F 20 mm dia Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S & F 25mm dia Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S & F in repairs 25 mm dia gun-metal globe or gate valves, with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and directed.

M & L in repairs for PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall 110 mm bore, complete all as specified and as directed.

S & F 100 mm dia PVC (SWR) bend all as specified and directed.

S&F rotational moulded water storage tank triple layer white colour (cylinderical vertical with closed top) hoisted and fixed in position capacity 1000 ltrs with 25mm bore brass float valve

Supply and fix in repairs ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 25 mm bore (Minimum weight-210gms) .

S & F Stainless steel railing with omamental stainless steel baluster of 32mm dia, spacing between two balusters not more then 1 mtr and height not less than 1 mtr with stainless steel hand rail at top not less than 50mm dia, 3 Nos of Stainless steel mild rails of 15mm dia welded to baluster including fixing arrangement as in floor or wall all as specified and directed.

M & L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick , set jointed and pointed in neat cement slurry with grey cement and pigments in floors.

M&L for 18 to 20 mm Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F PVC (SWR) pipes double socketed 110mm in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR)110mm junction single, (Single T) equal or unequal complete all as specified and directed.

S&F PVC (SWR) bends any radius bore of 110 mm complete all as specified and directed.

M&L for 10mm x 50mm ABS floor inlet nozzel (non return) for SWWIMING Pool complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floor, approns etc laid bedded and pointed in any mortar all as specified and directed.

M & L for 40mm thk cement concrete in SUB-FLOORS, SUB-BASES, FLOORS AND PAVINGS type B-1, 1:2:4 (20mm graded aggregate) etc complete all as specified and directed.

M & L for Vitrified ceramic tiles of premium quality, light shade, 8 to 10 mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 Sq.m (size 600 x 600 mm), laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified.

M & L for machine pressed pre-cast concrete interlocking coloured paver block of any size and shape onforming to IS-15658-2006 of 80mm thickness M-40 grade with grey cement and pigment etc complete all as specified and directed.

M & L for stone dust or sand base filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled, and blinded with earth and rammed including watering etc complete all as specified and directed.

M&L PCC 1:2:4 type B1 using (20 mm graded aggregate) as in kerbing all around of tile etc complete all as specified and directed.

Removing excavated / demolished material out side of MoD land etc complete

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for laying/taking out swimming pool water circulation pipe line and getting out in soft/loose soil all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and exceeding 1.5m but not exceeding 3m in depth for laying/taking out swimming pool water circulation pipe line and getting out in soft/loose soil all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and exceeding 3m but not exceeding 4.5m in depth for laying/taking out swimming pool water circulation pipe line and getting out in soft/loose soil all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and exceeding 4.5m but not exceeding 6m in depth for laying/taking out swimming pool water circulation pipe line and getting out in soft/loose soil all as specified and directed.

Returning, filling in soil including spreading leveling, watering and well ramming in layers not exceeding 25cm thick all as specified and directed.

Removing excavated materials not exc. 50 m and depositing where directed at a level not exe 1.5m above the starting point all as speciifed and directed.

Dismantling and taking out old/damage UPVC pipe of size 110 mm dia including all fittings complete all as specified and directed.

Supply, Installation, Testing and Commissioning PVC pressure Pipes dia of 100 MM, Class 5 (10kg/cm2) in replacement with plain socket suitable for solvent cement jointing conforming to IS:4985/2000 & fittings conforming to IS 7834/87, Cut to required lengths including all necessary fittings and specials such as bends, tees, unions, reducers, flanges and plugs etc. The pipes & fittings shall be tested to a pressure of 10 Kg/Sqcm. Make: Supreme/Astral/Finolex/Prince.

Taking down old unsv butterfly valve of size 100mm made up of stainless steel suitable for UPVC/HDPE/PPR pipe of size dia 110mm complete all as specified and directed.

Supply, Installation, Testing and Commissioning of CI butterfly valves, Tested to a pressure not less than 20 Kg/Sq.cm. Including rubber gasket, flanges, nuts, bolts, washers complete as required. Makr:Audco/Zoloto/Leader/Sant/Castle.

Dismantling and taking out old unsv light and Supply, installation, testing and commissioning of Pool under water integral LED Lights, model 20 Watt and 9'' dia wall mounted type working on 12 V DC, IP68 complete with built-in driver, including push in connector in 4 pole, including all fixing arrangement i.e, gasket,water proof sealing, screws etc in swimming pool wall to accommodate pool light including making necessary connection complete as specified and as directed by Engr-in-Charge. MAKE: Austin or as make approved by GE

Dismantling and taking out old unsv and Supply, Installation, testing and commissioning of ABS white plastic deck box, complete as specified and as directed by Engr-in-Charge

Dismantling and taking out old unsv 2 core 2.5 sq.mm. PVC insulated copper conductor unarmoured cable Wiring from under water lights to distribution panel complete as specified and as directed by Engr-in-Charge

Supply, installation, testing and commissioning in replacement of 2 core 4 sq.mm. PVC insulated copper conductor unarmoured cable Wiring from under water lights to distribution panel Make: Polycab/Havells/Finolex

Dismantling and taking out old unsv/damage and Supply, installation, testing and commissioning in replacement of heavy duty, PVC conduit 20 mm dia, ISI marked conduits complete with accessories such as bends, junction boxes, pull boxes etc. complete all as specified and directed.

Supply in replacement of 50 mm dia heavy duty in ground vacuum hose flexible and non corrosive material nylon with end connected swivel cuff 40 mm dia suitable for suction sweeper complete all as specified and directed.

S&F in replacement of nylon rope 15 mm outer dia heavy duty suitable for suction sweeper including removal of old rope all as specified and directed.

M&L in replacement earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried in ground vertical to a depth not less than 2.25 mtrs deep below ground level with top edge of plate not less than 1.5 mtr below normal ground level connected to galvanized GI strip of size 32 X 6 mm and 40 mm dia bore 7.5 mtr long light grade GI protection pipe for earth strip and GI watering pipe 40 mm dia medium grade from the top edge of earth plate fixed with deep cut on one end of pipe and fix from earth plate up to one feet above ground level of other end and plugged watering pipe at top with MS cap and grouted in PCC 1:2:4 of size 30 X 30 X 30 CM etc and 15 CM alternate layer of charcoal and salt around all sides of earth plate all as shown in electric plate no 3 of SSR part I of 2009. Note :- All joints either strip to strip of strip to earth plate are fixed with welded joints.

Supply, Installation, Testing and Commissioning of Flow adjastable ABS Floor Inlet nozzles UV treated with S.S. screws to fit in the 2" PVC pipes complete fitting all as specified and directed.

Supply, Installation, in replacement of 9" wide Overflow Grating made of UV Stabilized PP in white color, Width between 250-300 mm Height 22-25 mm all as specified and directed.

Dismantling and taking down old unsv under water light control panel including suitable capacity stabiliser and all connected acessories all as specified and directed.

Supply, Installation, Testing and Commissioning in replacement of under water light control panel suitable for 20 Nos under water LED Lights, model 20 Watt and 9'' dia wall mounted type working on 12 V DC, IP68 complete with built-in driver, including all fixing arrangement and all connected acessories all as specified and directed.

ANKIT SHIP REPAIRERS AND SUPPLIERS (BID ID -3279218)

LEKSHMI ENGINEERS (BID ID -3275970)

K.G.SHANKER (BID ID -3274599)