Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹18.0 LAccepted-AOC | L1 | Accepted-AOC Being lowest bidder | |
| 2 | L2₹21.9 L+₹3.8 L (21.3%)Rejected-Finance | L2 | Rejected-Finance Not being lowest | |
| 3 | L3₹22.9 L+₹4.9 L (27.3%)Rejected-Finance | L3 | Rejected-Finance Not being lowest | |
| 4 | L4₹23.1 L+₹5.1 L (28.2%)Rejected-Finance | L4 | Rejected-Finance Not being lowest | |
| 5 | L5₹23.3 L+₹5.3 L (29.3%)Rejected-Finance | L5 | Rejected-Finance Not being lowest |
Tender Value
₹22.8 L
EMD Value
₹45,700
Closing Date
16 May 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE Gangtok
GE Gangtok New Mil Stn Gangtok Sikkim 737102
Spl repair to bldg Nos P 150 and T 27 and certain other sanctioned works at New Mil Stn under GE Gangtok
2022_MES_508594_5
8015AE8
Open Tender
Miscellaneous Works
Item Rate
182 days
Gangtok
As per tender documents
8 documents required · 8 mandatory
₹500
GE Gangtok
₹45,700
Yes
26 May 2022
9 May 2022
18 May 2022
9 May 2022
16 May 2022
11 May 2022
60 days
Amount
SCHEDULE 'A' (B/R WORKS) Dismantling old PGI/CGI sheeting any gauge, thickness including Nainital, Sikkim or similar pattern roof/facia etc complete all as specified and as directed.
Taking down chowkats with shutter of any description (without taking down shutter from the frame) exc. 1.5 Sqm but not exc. 4.0 Sqm each and removing from site complete all as directed.
Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc, complete all as specified and as directed.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified & as directed.
Demolition of cement concrete in ground floors and paving n.exc 15cm thickness (un-reinforced) below or above ground level complete all as specified and as directed.
Excavation in post holes (or similar holes) in soft/loose soil each n.exc 0.5 Cum, getting out, returning, filling in an ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm and removing surplus soil to a distance n.exc 50 mtrs complete all as specified and as directed by the Engr-in-Charge.
M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.
Supply and fix 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and directed by the Engr-in- Charge.
Supply and fix 0.50mm thick pre-paintedgalvalume aluminium zinc coating GI based plain steel sheets of any colour having tensile strength of 550 Mpa as in ridges, valley,eaves,etc fixed with self tapping screws complete all as specifiec and directed by the Engr-in-Charge.
M&L Hardcore of gauge n exc. 63mm deposited spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.
Dismantling unframed wooden fillets, rail, posts, rafters, purlins, etc under 40 Sqcm in section complete all as specified and as directed.
Materials and labour for 2nd class hard wood plain fillets, square, rectangular or triangular in section, clean swan, secured with nails, cross sectional area exc 13 sq.cm & n.exc 25 sq.cm, complete all as specified and as directed.
S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed.
M&L for 30mm thick 2nd class hard wood well seasoned glazed and skeleton shutters, open rebated and prepared to receive glass gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete all as specified and as directed.
Taking down cement plaster of any description on brick or stone walls, including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by the Engr-in-Charge.
S&F 100mm long butt hinges, medium weight, cold rolled, mild steel complete all as specified.
S&F 300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed
S&F for extruded aluminium alloy handles 150mm long, fabricated type, anodised complete all as specified and as directed.
Supply and fix 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed by the Engr-in-Charge.
S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.
Materials & labour for coloured glazed ceramic tiles of size (300 mm x 200 mm / 350 mm x 250 mm / 450mm x 350mm ) x 7 mm thick as in vertical surfaces such as skirting/dado / riser to steps etc conforming to IS - 13712 grade IB-III set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including cement screed bed / backing layer of 10mm thick in cement mortar (1:4) complete all as specified and as directed.
M&L for pre cast cement concrete block masonry with solid blocks, n.exc. 10 cm in width and settting in cement mortar 1:6 type C1, (1:3:6) (using 20 mm graded stone aggregate) as per IS 383 complete all as specified and as directed.
M&L for pre cast cement concrete block masonry with solid blocks, exc. 10 cm in width and settting in cement mortar 1:6 type C1, (1:3:6) (using 20 mm graded stone aggregate) as per IS 383 complete all as specified and as directed.
M&L for brick work with sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.
M&L rendering 15mm thick in CM 1:6 on other than fair faces of brick or concrete surfaces complete all as specified and directed.
M&L for preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.
M&L Preparation of newly/old decorated surfaces of walls and applying two coats of white wash on new surfaces of walls all as specified and directed.
M&L for 75mm thick PCC (1:3:6), type C-2 (using 40 mm graded stone aggregate ) as in plinth protection; path / hardstanding etc finished the concrete surfaces even and smooth without using extra cement complete all as specified and as directed
S&F 75mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or under floors including necessary earthwork, fixed on walls complete all as specified and as directed.
S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafter and running rails and guides for sliding doors fixed with angle clear or other connecting plates conforing to Fe-410-W(Gde-E-250 quality-A)including one coat of red oxide zinc chrome primer after preparation of surfaces at contractor''s workshop before fabrication complete all as specified and as directed.
M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer to new or previously un-treated steel surfaces of any description over 10cm in width or girth including preparation of new steel surfaces complete all as specified and as directed.
Supply & fix in replacement Rotational moulded polyethylene water storage tank, 500 litres capacity, ISI marked multi layer constriction (cylindrical vertical with closed top), hoisted & fixed in position including supply and fixing of 25mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe of having weight not less than 455 gms including connection complete all as specified and as directed
Supply and fix galvanised steel water tubing 20 mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as directed.
Supply and fix galvanised steel water tubing 15 mm bore , medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as directed.
Supply & fix Bib tap , long body cast copper alloy, chromium plated fancy type with crutch or butterfly handle, screwed down for 15mm bore GI Pipe or for brass ferrule including taking down old unserviceable one. Make : ESSCO Cat Part No. SQT-511 KN or equivalent approved make
M&L RCC (Nominal mix) type B1, 1:2:4 using 20mm graded stone aggr as in columns, pillars, piers, post and struts etc complete all as specified and as directed
M&L for formwork to sides of concrete foundation, footings, bases of columns, raft & raft beams, sides & soffits (if any) of foundation & similar works, vertical of to batter, rough finished surfaces of concrete flat complete all as specified and as directed.
Demolition of concrete of any descripion and in any position not otherwise specially provided for complete all as specified and as directed.
Demolition of brickwork or stone/boulder masonry, built in cement mortar complete all as specified and as directed.
Dismantling of wall and ceiling hard boards/AC sheets(Fibre pulp insulation etc) or insulation board and plywood in any thickness & any position including cover fillets complete all as specified and as directed.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified & as directed.
Taking down chowkats with shutter of any description (without taking down shutter from the frame) n.exc. 1.5 Sqm each and removing from site complete all as directed.
Material & labour for rendering 20 mm thick in cement mortar (1:4) in two layer of 10 mm thick and 5mm thick each with using Water Proofing Compound @ 3% of weight of cement shall be mixed with cement mortar in finishing outer layer only, as per manufacturer instruction, on fair face of brick work or concrete surfaces, finished fair and even with out using extra cement complete all as specified and as directed.
M&L for applying two coats of exterior acrylic emulsion weather proof paint over a coat of primer on new/old plastered surface etc complete all as specified and as directed.
M&L for preparation of newly plastered surfaces of walls applying two coats of distemper, oil emulsion, white or tinted over new wall surface on a coat wall care putty complete all as specified and as directed.
M&L for preparation of old plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer applied over 3mm thick super fine Birla or altek wall care putty finish including complete removal of existing treatment complete all as specified and as directed.
S&F powder coated GI grid frame work for false ceiling comprising of the following sections for making partitions of 600mmx600mm size fixed to walls with rawl plugs & screws and hanges to roof with and including 1mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 23mmx28mmx0.30 thick thick, cross tee shall be 23mmx28mmx0.30mm thick and wall angle shall be 20mm x20mm x0.30mm thick complete all as specified and as directed.
S&F 4mm thick Non asbestos fibre cement building boards (E-board) of approved texture, for insulation and acoustic purpose of size 595x595mm size fixd with staples on snap grid as in ceiling with and including dusting of surfaces and applying two coats of oil emulsion diatemper over a coat of primer including preparation of surfaces complete all as specified and as directed.
Hacking out old broken glass any thickness, size, quality or description from metal/wooden frame including puching or drilling out old glazing pins and removal of demolished material from site complete all as specified and as directed.
M&L for preparation of old or previously treated steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint over old steel surface complete all as specified and as directed.
S&F in repair 3.0 mm thick tinted sheet glass panes, ordinary quality and glazing with oil putty including steel pin in square n.exc 0.5 Sqm in each pane fixed to steel frame complete all as specified and as directed.
S&F as in repair stain less steel wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40m and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.
Material and labour for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in surface channels and drains including forming fair finished to drain channel complete all as specified and as directed.
Material & labour for non skid coloured ceramic tiles of 7 to 8mm thick ( Square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.36 Sqm as in floors etc conforming to IS-13712, grade B-II-(a) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including cement screed bed/bedding layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed.
All as per Sl item No. 54 above but on vertical surfaces of wall like skerting/dao etc on 15mm thick rendering complete all as specified and as directed.
Supply only Water Proofing Compound complete all as specified and as directed.
Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.
M&L for 75mm thick PCC (1:3:6), type C2 (using 40mm graded stone aggregate) as in plinth/hardstanding finished the concrete surfaces even and fair without using extra cement etc complete all as specified and as directed.
M&L for 75mm thick PCC (1:2:4), type B-1(using 40mm graded stone aggregate) as in floor complete all as specified and as directed.
M&L for 40mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in floor complete all as specified and as directed.
S&F 38mm wide x 3mm thick Glass dividing strips, as in floor complete all as specified and as directed.
M&L for 2nd class hardwood timber scantling of any size or in any position such as truss, purlin etc and fix in repairs, to replace old and decayed timber (including piercing, scarifying etc of old and new timbers if required) and removing defective portions to store complete all as specified and as directed.
Materials & labour for 4 mm thick plywood, 5 ply, grade BWR, type BB, fixed with screws to timber frame work in wall / ceiling complete all as specified and as directed.
Materials and labour for 2nd class hard wood plain fillets, square, rectangular or triangular in section, clean swan, secured with nails, cross sectional area exc 6 sq.cm & n.exc 13 sq.cm, complete all as specified and as directed.
Supply and fix flush shutter 35mm thick solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and as directed.
Supply and fix 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.
Supply and fix 150 mm long aluminium handles, cast type, anodised complete all as specified and as directed.
S&F 250 mm aluminium anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed
M&L for RCC 1:2:4, type B-1 (using 20mm graded stone aggregate) as in foundations, including raft footings, foundation beams, plinth beams, bases for columns, lintel beam, cover slab etc basement slabs, under remaed piles and mass concrete including necessary formwork complete all as specified and as directed.
Material & labour for Mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking , bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified & as directed.
Excavating in post holes (or similar holes) each n.ec 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceding 25cm complete all as specified and as directed.
M&L for applying three coats of white wash on new plastered wall surface including preparation of new and previously untreated surfaces of wall complete all as specified and as directed.
M&L for applying two coats of white wash on old plastered wall surface including preparation of old surfaces of wall complete all as specified and as directed.
M&L for PCC 1:3:6 type C1 (20mm graded aggregate) as in coping, roof kerb, bed plates, parapet, plinth course including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.
Taking down 15mm dia steel tubing and connections, including cleaning and refixing or removal to store complete all as specified and as directed.
Taking down 20mm dia steel tubing and connections, including cleaning and refixing or removal to store complete all as specified and as directed.
Refixing of old 15mm bore steel tubing and connections in new or old position (wall, ceiling or floor etc) complete all as specified and as directed.
Supply and fix vitreous china, white colour flat back, wash hand basin (full padestal pattern) of size 540 x 395x 185mm fixed with and including fixing accessories like CP wate coupling (half or full threaded, waste pipe etc complete all as specified and as directed. Make : Cera Model CORNET Cat No S2040105 & S2090101 or equivalent approved .
S&F chromium plated central hole basin mixer extended casted spout with 450mm long braided hoses. Make : Essco Cat Part No. DLX-516KN or equivalent.
Supply & fix 15mm bore dia angular stop cocks with flange, chromium plated, with wall flange screwed down, screwed from iron pipe or union and complete all as specified and as directed Make: Cera CAT No : QT F2006201/HTF3001201 or equivalent approved complete all as specified and as directed.
Excavating in trenches not exceeding 1.5 metre wide and not exc 1.5 metre in depth and getting out as in soft/loose soil for foundation etc complete all as specified and as directed.
M & L walling of random rubble stone masonry uncoursed, well bonded, bedded and solidly hearted built in CM 1: 6 incl brought upto course at interval of every 60cm complete all as specified and as directed.
Returning, filling in, including spreading levelling watering and well ramming in layers not exceeding 25 cms in thick as in soft/loose soils complete all as specified and directed.
Removing surplus soils to a distance not exceeding 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and directed.
Disconnecting existing tanks of capacity exc 500 Ltr but n.exc 1000 Ltr setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position complete all as specified and as directed. Note : - Cleaning, repairing etc shall be measured separately.
SCHEDULE 'A' (E/M WORKS) Taking down carefully point wiring of any type (i.e. on wooden batten, surface conduit, casing-N- capping or concealed conduit) complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, conduit etc. including accessories such as wooden gutties/rawal plug, screw etc including making good disturbed surface to match the existing surface all as specified & directed.
M&L for point wiring with 1.5 Sqmm (nominal cross-sectional area) PVC (FRLS) insulated unsheathed single core copper cable working voltage 1100 volts grade conforming to IS-694 with multistranded copper conductor in including PVC heavy grade rigid non metallic 25mm PVC casing caping (double Lock) including PVC polycarbonate/PVC/recatangular block/box of suitable size fixed by means of brass machine screw and cap washer including size 1.5 sqmm (nomnal cross sectionl area PVC (FRLS) insulated unsheathed single core multistranded copper conductor cable as earth continuity conductor connected to main switches/DBs or common earth dolly complete all as specified and directed for the following .Make of cable-Havells/Finolex/plaza, Make of casing caping- Prestoplast/Plaza/Modi.
All as per Sl item No. 88 above but one switch socket outlet point 5/6 Amps on independent board.
All as per item No 88 here-in-before but for one socket outlet of 15 Amps fixed on independent board with 4 Sq mm multistranded copper conductor wire FRLS PVC insulated and 4Sq mm copper conductor wire FRLS PVC insulated using as earth wire complete all as specified and directed by Engineer-in-Charge
S&F in repairs switch piano flush button,single pole,one way(ISI marked), 6 amps, 230 volts complete all as specified and as directed. Make : Anchor product code No. 50053 or equivalent of approved make
S&F ceiling rose,PVC/ polycarbonate insulated body, 3 terminal and 240 volts, ISI marked complete all as specified and directed. Make : Anchor Product Code No 39040 or equivalent approved.
S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required complete all as specified and as directed.
S&F switch socket combination, 2 and 3 pin, 5/6 amps, multipurpose, flush, non shutter, non inter locking type, 230 volt flush type, white/ivory finish with two fixing hole including suitable gang box complete all as directed including taking down old one. Make : Anchor Product Code No 4056/50483 or equivalent of approved make
S&F switch socket combination, 2 in 1, 6 pin, 5/6 Amps and 15/16 Amps, multipurpose, flush, non shutter, non inter locking type, 230 volt flush type, white/ivory finish with two fixing hole including suitable gang box complete all as specified and as directed.Make : Anchor Cat No. 38808/50665 or equivalent approved.
Supply and fix lamp holder,angular/straight insulated body with back plate PVC/Polycarbonate type with cord grip cap suitable for batten fittings white/ivory finish and fixing of 20/18 watt CFL. Make : Anchor Product Code No. 39527 or equivalent approved.
S&F LED light fitting 1x 20 W, 220V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.
S&F LED light fitting 1x9W/1x10W bulk head luminairies including LED light driver holder connecting up with three core flexible copper flexible copper conductor cable of suitable size complee all as specified and as directed.
S&F sheet metal enclosure DB's 240 volts,IP-43 suitable for mounting MCB's SPN, 8 way with 200 Amps rated copper bus bar double door type complete all as specifed and as directed Havells/ABB/Legrand. Make :L&T Cat No DBSPN008DD or equivalent approved.
S&F MCB single pole & neutral 40 to 63 amps, 240 volts, 10 KA rapturing capacity, 'C' Curve complete all as specified and as directed. (Make : L&T Cat No. BB20400C to BB20630C or equivalent approved)
S&F MCB single pole 6 to 32 Amps, 240 volts, 10 KA rapturing capacity 'C' Curve complete all as specified and directed by Engr-in-Charge. (Make : L&T cat no BB10060C to BB 10320C or equivalent approved)
M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connected with galvanised iron/steel earth wire of 4mm dia by means of bolts, nuts, check nuts and washers made outof galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part-I (2009) and earth wire protected by galvanized pipe light grade 15mm bore and connected to VTPN DB/SPN DB including neccessary earthwork and excavation in any type of soil, GI light grade 20mm bore watering pipe with funnel and wire mesh, PCC 1:2:4 type B1 chamber with 40mm thick RCC 1:2;4 type B1 design mix cover slab with 6mm dia MS bars at 100mm c/c both ways with MS hook 6mm dia MS bars etc complete all as specified and as directed including testing on completion.
KAMLESH ENTERPRISE
M/S ANIL KUMAR THAKUR
BIJAY MITTAL
KARMA SHERPA
NISHA CONSTRUCTIONS
M/S S. S CHETTRI AND SONS
DHARMINDER SINGH
MAHENDRA KHAWAS
stage.html
html • 0.07 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .