Renovation of Gandhi ganj Public toilet

RENOVATION OF CANTONMENT GROUP LATRINE AT GANDHI GANJ.

Dismentling of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

Dismentling of Stone slabs and tiles of any description or thickness in floors, aprons etc. Laid, bedded and pointed in any mortar floor tile wall tile

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) Cement concrete (unreinforced)

Demolition of Roofs, floors (other than ground floors), beams, staircases, landing,chajjas and similar suspended work Cement concrete (unreinforced) lintel beam top beam

Dismantling framed trusses N exc 10 m

Dismantling structural steel work including doors, gates but excluding framed truss etc.

Site Clearance Soft/loose soil

Rough excavation not exceeding 1.5 m deep and getting out in hand dense soil

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hand dense soil

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering

Shingle filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled, and blinded with earth and rammed including watering

Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area M&L plinth area

Cement concrete in foundations, filling and mass concrete Type C2 1:3:6 (40 mm graded aggregate) Nominal Mix -1 Cement : 4sand :8graded stone agrt. (M -7.5) floor base ramp & stairs base stairs stitch slab ramp and stairs

Cement concrete in surface channels and drains Type C2 1:3:6 (40 mm graded aggregate)

Ditto, in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed cill

Foundations, including rafts, footings, foundation beams;plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete M-20 (20mm graded aggregates) All works up to plinth level (footing raft, pedstal, RCC drain, RCC

Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses M-20 (20mm graded aggregates)

Columns, pillars, piers, posts and struts M-20 (20mm graded aggregates)

Beams, cantilevers, bressummers, lintels over 1.5m span M-20 (20mm graded aggregates)

Chajjas M-20 (20mm graded aggregates)

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter Rough finished surfaces of concrete Flat

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work includingattached pillasters, buttresses, etc.; vertical or to batter Rough finished surfaces of concrete Flat

Formwork to sides of pillars, posts, struts, piers, columns and stanchion Rough finished surfaces of concrete Square, rectangular or polyg-onal

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc Rough finished surfaces of concrete Flat

Formwork to chullah hoods, chajjas, troughs and similar items including edges Rough finished surfaces of concrete Flat

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and includingmild steel wire (annealed) not less than 0.9mm dia or securing with clips

Mild steel bars 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in Old size bricks in cement mortar 1:6

Brickwork with flyash bricks, straight or curved on plan to any radius i n half brick thick walls, built in Old size bricks in cement mortar1:6

Damp proof course to horizontal or vertical surfaces including necessary formwork In cement concrete 1:2:4, type B-0 40mm thick

Rendering 10mm thick on fair faces of brick work or concrete surfaces Cement plaster 1:6

Add or deduct to/from the rates for rendering for each 5 mm thickness over or under 10mm Cement plaster 1:6

Rendering 10mm thick on fair faces of brick work or concrete surfaces Cement plaster1:6 Add if in ceilings

Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete M & L

20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete M & L

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations stairs platform

Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite M & L 20mm thick

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing S & F

Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match Coloured tiles (floor tiles)

Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match Coloured tiles wall tiles

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides S & F Thickness in 30 mm

Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions M&L Thickness in 0.9 mm

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing S & F With Particle Board Core

Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified S & F

Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified S & F

Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane 16002 Ditto, but exc 0.5 sq. m in each pane Thickness in 4-0 mm

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 S & F

Stairs (framed) including stringers, treades, landing balusters, hand rails etc. in cluding cleats, brackets, etc complete

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

3mm thick wall care putty on wall SUM OF ALL PLASTER

Distempering walls with distemper dry, white or tinted 1st coat+Subsequent coat

Ditto with distemper oilemulsion, ditto 1st coat+Subsequent coat

Surfaces of any description, over 10cm in width or gir th, not otherwise described Synthetic enamel (ordinary tint)

Mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed Length of bolt in 300 mm

Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed Length of bolt in 300 mm

Mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed Length of bolt in 150 mm

Cast iron or malleable cast iron handles, cast type, stove enamelled black Size of handle in 125 mm

Brass body and tongue with hard drawn steel spring Overall length of cover plate 150mm

Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed S & F Cast iron body

Bitumastic gola,with 80/25 bitumen and coarse sand mixture. 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mi- tres and stopped ends, etc.

Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275.

Thatched cappings to ridges and Hips M & L

Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

Water closet (Squatt pattern) com plete including provision of lime concrete bedding

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe)

Wash down water closet (Pedestal pattern), complete

Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)

Wash basins, Vitreous China (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe

Vitreous China wash basin, white, flat back, size 630x450mm excluding ditto but including brackets

Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe)

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors S & F Bore im mm 75 (60 running meter) S & F Bore im mm 110 (60 running meter)

PVC (SWR) bends any radius S & F Bore im mm 75 (20 nos) S & F Bore im mm 110 (20 nos)

PVC (SWR) branch piece, single (single Y) equal or unequal S & F Bore im mm 75 (20 nos) S & F Bore im mm 110 (20 nos)

PVC (SWR) branch piece, double (double Y) equal or unequal S & F Bore im mm 75 (20 nos) S & F Bore im mm 110 (20 nos)

VC (SWR) junction single, (Single T) equal or unequal S & F Bore im mm 75 (20 nos) S & F Bore im mm 110 (20 nos)

PVC (SWR) junction double, (double T), equal or unequal S & F Bore im mm 75 (20 nos) S & F Bore im mm 110 (20 nos)

Add item no. 76 to 81if provided with Sccess door S & F Bore im mm 75 (20 nos) S & F Bore im mm 110 (20 nos)

PVC (SWR) couplers S & F Bore im mm 75 (20 nos) S & F Bore im mm 110 (20 nos)

PVC (SWR) reducers S & F Bore im mm 110 (20 nos)

PVC (SWR) vent cowl S & F Bore im mm 75 (20 nos) S & F Bore im mm 110 (20 nos)

PVC (SWR) 'P’ trap S & F Bore im mm 125/110 (20 nos) S & F Bore im mm 110/110 (20 nos)

PVC (SWR)’Q’ trap S & F Bore im mm 125/110 (20 nos) S & F Bore im mm 110/110 (20 nos)

PVC (SWR) 'S' trap S & F Bore im mm 125/110 (20 nos) S & F Bore im mm 110/110 (20 nos)

Tubular towel rail, 20mm dia, D type, 60cm long between flanges S & F Brass chromium plated

Soap dish, vitreous China white, approximate size 160x 160x90mm

Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms)

Unplasticiscd PVC pipes of pressure rating 10 kgf/cm2 laid in trenches Bore of pipes in mm 15 mm (30 meter) Bore of pipes in mm 20 mm (30 meter) Bore of pipes in mm 25 mm (30 meter)

Push tap any colour high pressure of PTMT screwed for iron pipe and fixed, (Minimum weight 15mm-47gms/ 20mm- 75gms) S & F Bore dia of pipe in mm 15 mm

Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/ 20mm-92gms) 15 mm nominal bore.)

Reinforced concrete pipes, class NP2, laid and jointed complete with collars 150mm dia. R.C.C. pipe 200mm dia. R.C.C. pipe

Providing and fixing Unplasticised -PVC pipe clips of approved design to Unplasticised - PVC soil and waste pipes by means of bombay nail of required length including and making good the wall etc. complete 110 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings. This included jointing of pipes and fittings with one step CPVC solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer in Charge

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc

Providing and fixing CP jet assembly to including connection etc complete.

Providing and fixing square-mouth S.W. gully trap class SP1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement: 4 sand) R.C.C. top slab with Cement Concrete 1:2:4 mix (1 cement: 2 sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 sand: 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 sand) fmished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 em and 45 em deep including CJ. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With well burnt bricks

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.30.1 With well burnt bricks

Point wiring (excluding metallic switch box & sheet but including switches, sockets,lamp holders/ceiling roses etc) with 1.5 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI Marked of suitable size and 1.5 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit etc. as required as per specification for :- Using Flush Type Normal Accessories : (Light point/Fan points )

Wiring for circuit wiring with PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) of ISI marked suitable size etc. as required as per specification.

Supplying and fixing factory fabricated hot dip galvanised switch box for normal flush type accessories of minimum 1.2 mm (18 swg gauge) thickness with earth terminal stud with nut and washer, with 3 mm thick synthetic phenollic resin bonded laminated sheet conforming to grade P-I of IS:2036-1974 on surface / concealed including painting etc. as required as per specification::- MS Box 180 mm X 100 mm X 60 mm Deep

Supplying of ISI Marked and accepted standard of Miniature Circuit Breaker (MCB) of 'C' series suitable for 240/415 Volts, 50 Cycle , 10 kA Value AC supply confirming to IS : 8828 : 1996, IEC : 60898 :2002 but without enclosures. SINGLE POLE (SP) 6 Amp to 32 Amp Rating

Supplying of MCB Isolators suitable for 240/415 Volts, 50 Hz AC supply with KA value rating 10 kA of approved make confirming to IS :13947-Part III : 1993 & IEC :60947- 3:2001 (without enclosures ) TWO POLE 40 Amps.

Supply of approved make powder coated sheet steel encloser SPN MCB DB inclusive of Busbar, Neutral bar, Earth bar & two earth terminals etc. complete as per IS:13032( exclusive of MCB & isolator) 8 way Double Door IP 43 protection

Fixing of MCB /MCCB/ Isolator in sheet steel enclosure as required as per accepted practice, including mounting on busbar and cable connection etc. complete (Labour only) MCB / Isolator SP/DP

Labour charges for fixing sheet steel enclosures, MCB DB flush mounting type, as per accepted practice, duly embedded and end plate completely flushed in wall, cable connection etc.complete

Supplying, erection and testing of approved make 'Fresh Air Fan' AC 230-250 volts with connection and including frame bolt/Anchor hole fasteners etc. complete finished of approved as required 300mm sweep

Supply and fixing Led tube rod comprising of LED tube with non integral / integral driver,4000K to 6500K color temp having more then 25000 to 40000 burning hrs life with minimum @ L 80, system lumen output should be minimum with efficacy > 90 lm/W. LED driver PF 0.90 & THD < 30%. The colour rendering index of LED light should be more than 70. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106 from NABL approved lab. Manufacturer manadatory i/c connection wire, testing etc. to complete the job. 2 Yrs Guarantee certificate from manufacturer. 18/20/22W, Intregral

Supplying and fixing surface mounting LED down lighter, LED of 1 to 3 W each assembled on single MCPCB, having color temp 4000K to 6500K & having 25000 to 50000 burning hrs life with minimum @ L 80, system lumen output should be minimum with efficacy>80 lm/W. LED driver PF 0.90. The colour rendering index of LED light should be more than 70. Housing made of CRCA powder coated frame with glare free diffused polycorbonate cover. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106 from NABL approved lab. Manufacturer manadatory. i/c connection wire, testing etc. to complete the job. 2 Yrs Guarantee certificate from manufacturer. 15 W, 180/200mm

Providing and fixing earthing arrangement with 38.1mm dia 2.5 metre long galvanized iron pipe electrode including packing of charcoal powder and salt as per specification watering pipe 19mm dia G.I. Connection, cover plate having locking arrangment on the top etc. complete with refilling the pit as required, including excavation of earth pit in soil / soft rock

Supplying and laying G.I. earth lead duly installed on wall or in G.I. Pipe including connections etc. complete as required. 13 sq mm (4 mm dia)

Supplying and drawing single core PVC insulated cable FR with copper multi strand conductor ISI marked in existing rigid PVC Casing-N-Capping / conduit in surface or concealed as per specification. 2.5 Sq mm cable (a) 1 X 2.5 sq mm

Providing and fixing wooden board of suitable size (maxinum 12" X 18" ) for fixing of house service Metre with necessary materials and connection testing etc. complete as per specification Single phase Meter

Supplying & fixing of ISI marked Porcelain Rewireable type fuse carrier & base unit of approved make & confirming to IS: 16 Amps./415 Volts or 32 Amps/240 Volts

Supply of XLPE Insulated power cable (confirming IS-7098 Part-I ) 1100 Volt grade, 1 core /2 core /3½ core/4 core ISI MARKED with Alu. Stranded /solid conductor. 2 CORE ARMOURED 6 Sq.mm(XLPE)

Laying of one number armoured / unarmoured cable 1.1kV grade of size not exceeding 25 Sq.mm on wall/truss with approved type of iron clamps etc. as required.

Laying of underground cable armoured./ unarmoured as per specification in air suspended on existing approved type of iron clamps, G.I wire 7/1.6mm & shackle insulator / insulated strip complete. 1/2 / 3 / 4 Core cable upto 16 Sq.mm

Supplying and drawing G.I. bearer wire 7/1.6mm including stringing, binding at existing brackets / pole, etc. for cable support in air as required and clearing of obstacles (if any)

Supplying and erection of 75mm x 90mm shackle insulator with G.I. bolts, nuts and straps etc. as required.

Supply, fabrication and erection of Angle/Chanel/Flat iron fitting for over head line & sub-station etc such as 'D' bracket, cross arms, top clamp, 'V' cross arms, Back/Support clamps or other similar work etc. including nut bolts of required size, making holes, fabrication, welding, cutting, etc. and painting with one coat of red oxide paint & two coat of aluminium paint as required as per specification.

Uday Traders