Electronic Components 178 types

Mission & Combat System Research & Design Centre HINDUSTAN AERONAUTICS LIMITED Marathalli Post Bangalore - 560 037 INDIA

Technical Terms and Conditions of Tender - Annexure - 1

Tender Ref. No. MC/S461/2158/24/1

Name of Work: Electronic Components - 178 types

Name of the Vendor/ Firm:

Quotation Ref. No.:

PLEASE INDICATE YOUR RESPONSE/ COMPLAINCE/ACCEPTANCE TO THE FOLLOWING TERMS (MANDATORY). INDICATE THE TECHNICAL SPECIFICATION/RANGE AGAINST HAL TECHNICAL REUIREMENTS WHEREVER NECESSARY

Sl. No. HAL Scope of Work Vendor's Compliance (Complied or not complied)

1 PURPOSE This document is to define the technical requirements for the submission of techno commercial proposal for supply of Electronic Components - 178 types

2 TECHNICAL REQUIREMENTS

Line No. Product Description Part Number Qty (Nos.)

1 Ceramic CAP 0.1uF ±10%, 25V,X8R 0603 Make: Murata Electronics GCM188R91E104KA37D 100

2 Ceramic CAP 10uF ±20%, 10V,X5R 0603 Make: TAIYO YUDEN LMK107BJ106MALTD 100

3 Ceramic CAP 10uf ±10%, 16V,X7R 1206 Make: TDK Corporation C3216X7R1C106K160AC 100

4 Ceramic CAP 0.1uF ±10%,10V,X7R 0402 Make: Murata Electronics GCM155R71A104KA55D 550

5 Ceramic CAP 1nF ±10%,100V,X7R 0402 Make: Murata Electronics GCM155R72A102KA37D 50

6 Ceramic CAP 10nF ±10%,50V,X7R,0402, Make: Yageo AC0402JRX7R9BB104 100

7 CAP 0.82uf ±10%,25V,X7R 0805 Make: KEMET C0805C824K3RACAUTO 50

8 Ceramic CAP 47pF ±5%,50V,NP0 0402 Make: TDK Corporation CGA2B2NP01H470J050BA 50

9 Ceramic CAP 2.2nF ±10%,16V,X7R 0402 Make: KEMET C0402C222K4RACAUTO 50

10 CAP 12nF ±10%,16V,X7R 0402 Make: KEMET C0402C123K4RACAUTO 50

11 Ceramic CAP 0.15uf ±10%,25V,X7R 0402 Make: TDK Corporation CGA2B3X7R1E154K050BB 50

12 Ceramic CAP 22uf ±10%,16V,X7R 1210 Make: Murata Electronics GCM32ER71C226KE19L 50

13 Ceramic CAP 0.01uf ±10%,25V,X7R 0402 Make: KEMET C0402C103K3RACAUTO 100

14 Ceramic CAP 1uF ±10%,16V,X7R 0603 Make: KEMET C0603C105K4RACAUTO 50

15 Cerami CAP 47pF ±5% 16V, X8R ,0402 Make: KEMET C0402C470J4HACAUTO 50

16 Ceramic CAP 18pF, ±5% ,50V,NP0 0402 Make: TDK Corporation CGA2B2NP01H180J050BA 50

17 Ceramic CAP 12pF ±5%,50V,X8R 0402 Make: KEMET C0402C120J5HACAUTO 50

18 Molded Tantalum CAP 220uF ±10%,10V, 2917 Make: KEMET T491D227K010ATAUTO 50

19 Ceramic CAP 0.1uF ±10%,25V,X7R 0402 Make:TDK Corporation CGA2B3X7R1E104K050BB 50

20 Ceramic CAP 330pF ±10%,25V,X7R 0402 Make: KEMET C0402C331K3RACAUTO 100

21 Ceramic CAP 10uF ±10%,25V,X7R 1206 Make: KEMET C1206C106K3RACAUTO 50

22 Ceramic CAP 0.1uF 0.1uF ±10%,25V,X7R 1206 Make: KEMET C1206C104K3RACAUTO 50

23 Conformal coated tantalumCAP 100uF ±20%,35V,3024 Make: Vishay Sprague 597D107X0035F2T 50

24 Conformal coated tantalum CAP 47uF ±10%,50V, 3024 Make: Vishay Sprague 597D476X9050Z2T 50

25 Ceramic CAP 0.1uF ±10%,25V,X7R 1206 Make: YAGEO AC1206KRX7R8BB104 50

26 Ceramic CAP 4700pF ±10%,25V,X7R 0402 Make: KEMET C0402C472K3RACAUTO 50

27 Ceramic CAP ,100pF ±10%,25V,X8R 0603 Make: KEMET C0603C101K3HACAUTO 50

28 Ceramic CAP ,10nf ±10%,25V,X8G 0603 Make: KEMET C0603C103K3TACAUTO 50

29 Ceramic CAP ,10pF ±10%,16V,X8R 0805 Make: KEMET C0805C100K4HACAUTO 50

30 Ceramic CAP ,4.7uF ±10%,25V,X7R 0805 Make: KEMET C0805C475K3RACAUTO 50

31 CAP 0.1uF ±10%,25V,X8R 0603,MLCC Make: TDK CGA3E2X8R1E104K080A 50

32 CAP 1uF ±10%,100V,X7R 1206,MLCC Make: TDK CGA5L2X7R2A105K160AA 50

33 CAP 47uF ±20%,35V,X7R 2220,MLCC Make: TDK CGA9N1X7R1V476M230KC 50

34 CAP 1.5uF ±10%,100V,X7S 1206,MLCC Make: TDK CGJ5L3X7S2A155K160AA 50

35 Ceramic CAP,10pF ±10%,16V,X8R 0603 Make: KEMET CO603C100K4HACAUTO 50

36 Ceramic CAP, 33pF ±10%,16V,X8R 0603 Make: KEMET CO603C330K4HACAUTO 50

37 Ceramic CAP ,56pF ±10%,16V,X8R 0603 Make: KEMET CO603C560K4HACAUTO 50

38 Ceramic CAP, 47uF ±10%,6.3V,X6S 1206 Make: Murata Electronics GRT31CC80J476KE13L 50

39 Tantalum CAP, 100uF ±15%,10V,B-Case Make: KEMET T491B107K010ATAUTO 50

40 Ceramic CAP ,47uF ±10%,16V,X6S 1210 Make: Murata Electronics GRT32EC81C476KE13L 50

41 Ceramic CAP ,2.2uF ±10%,16V,X7S 0603 Make: Murata Electronics GRT188C71C225KE13D 50

42 Ceramic CAP ,1nF ±10% 100V,X7R 0603 Make: Murata Electronics GCM188R72A102KA37D 50

43 CAP 100nF,±10%,100V,X7S 0603,MLCC Make: TDKCorporation CGA3E3X7S2A104K080AB 50

44 Ceramic CAP,1uF±10%,16V,X8L 0805 Make: Murata Electronics GCM21BL81C105KA58L 50

45 Ceramic CAP, 2.2uF ±10%,25V,X7R 0805 Make: Murata Electronics GCM21BR71E225KA73L 50

46 Ceramic CAP ,10uF ±10%,25V,X7S 1206 Make: Murata Electronics GCM31CC71E106KA03L 50

47 Ceramic CAP, 15nF ± 10% ,25V, X7R 0402 Make: Murata Electronics GCM155R71E153KA55D 50

48 Ceramic CAP,0.1uF ±10%,16V,X7R 0402 Make: Murata Electronics GCM155R71C104KA55J 50

49 Ceramic CAP,10nF ±10%, 100V, X7R 0603 Make: Murata Electronics GCM188R72A103KA37D 50

50 RES 0E jumper chip resistor 1/10W, 0603 Make: Vishya Dale CRCW06030000Z0EA 650

51 RES 4.7K ±1% ,1/16W,0402 Make: Vishya Dale CRCW04024K70FKED 50

52 RES 0E jumper chip resistor 1/16W, 0402 Make: Vishay Dale CRCW04020000Z0ED 300

53 RES 560E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402560RFKED 100

54 RES 120Ohm_DNM ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402120RFKED 50

55 RES 10K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040210FKED 300

56 RES 634E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402634RFKED 50

57 RES 15K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040215K0FKED 50

58 RES 75 OHM ±1% ,1/16W,0402 Make: Vishay Dale CRCW040275R0FKED 450

59 RES 150E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402150RFKED 50

60 RES 33E ±1% ,1/16W,0402 Make: Vishay Dale CRCW040233R0FKED 200

61 RES 2.7K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04022K70FKED 50

62 RES 1.69K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04021K69FKED 50

63 RES 100E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402100RFKED 100

64 RES 5.6K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04025K60FKED 50

65 RES 1M ±1% ,1/16W,0402 Make: Vishay Dale CRCW04021M00FKED 50

66 RES 510E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402510RFKED 50

67 RES 1K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04021K00FKED 100

68 RES 169E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402169RFKED 50

69 RES 20K Ohm ±1% ,1/16W,0402 Make: Vishay Dale CRCW040220K0FKED 50

70 RES 2K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04022K00FKED 50

71 RES 787E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402787RFKED 50

72 RES 1.2K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04021K20FKED 50

73 RES 37.4E ±1% ,1/16W,0402 Make: Vishay Dale CRCW040237R4FKED 50

74 RES 59E ±1% ,1/16W,0402 Make: Vishay Dale CRCW040259R0FKED 100

75 RES 47K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040247K0FKED 50

76 RES 220E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402220RFKED 50

77 RES 330E ±1% ,1/16W,0402 Make: Vishay Dale CECW0402330RFKED 50

78 RES 36E ±1% ,1/16W,0402 Make: Vishay Dale CRCW040236R0FFKED 50

79 RES 39E ±1% ,1/16W,0402 Make: Vishay Dale CRCW040239R0FKED 50

80 RES 681K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402681KFKED 50

81 RES 470E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402470RFKED 50

82 RES 0E jumper chip resistor 1/16W, 0805 Make: Vishay Dale CRCW08050000Z0EA 50

83 Thick film RES 5.62 ohm ,±1% 1206,100ppm,1/4W, Make: Vishay CRCW12065R62FKEA 50

84 Thin Film RES 1.5K ,±1%,0603,100ppm Make: Vishay M55342K12B1E50RTS 50

85 RES 470E ,±1%, 1/8W,0805 Make: Vishay CRCW0805470RFKEA 50

86 RES 7.68k ±1% ,1/16W,0402 Make: Vishay Dale CRCW04027K68FKED 50

87 RES 11k ±1% ,1/16W,0402 Make: Vishay Dale CRCW040211K0FKED 50

88 RES 100K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402100KFKED 50

89 RES 10 ±1% ,1/16W,0402 Make: Vishay Dale CRCW080510R0FKED 50

90 RES 200K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402200KFKED 50

91 RES 0.015E ,±1% ,15mohms,1/4W,1206 Make: Yageo RL1206FR-070R015L 50

92 RES 221K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402221KFKED 50

93 RES 2.99K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04022K94FKED 50

94 RES 29.4K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040229K4FKED 50

95 RES 80.6K ohm ±1% ,1/16W,0402 Make: YAGEO AF0402FR0780K6L 50

96 RES 13.7K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040213K7FKED 50

97 RES 4.99K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04024K99FKED 50

98 RES 120K ±1%, 1/16W,0402 Make: Vishay Dale CRCW0402120KFKED 50

99 RES 332K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402332KFKED 50

100 RES 100E ±1% 1/10W, 0603 Make: Vishay Dale CRCW0603100RFKEA 50

101 RES 1.5K ohm ±1% ,1/16W,0402 Make: Vishay Dale CRCW04021K50FKED 50

102 RES 220K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402220KFKED 50

103 RES 270K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402270KFKED 50

104 RES 240Ohm ±1% 1/10W, 0603 Make: Vishay Dale CRCW0603240RFKEA 50

105 RES 84.5K ±1% 1/10W, 0402 Make: Panasonic Electronic Components ERJ-H2RF8452X 50

106 RES 14.7K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040214K7FKED 50

107 RES 30K_DNM ±1% ,1/16W,0402 Make: Vishay Dale CRCW040230K0FKED 50

108 RES 38K_DNM ±1% ,1/16W,0402 Make: Vishay Dale CRCW040239K0FKED 50

109 RES 18.7K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040218K7FKED 50

110 RES 402K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402402KFKED 50

111 RES 17.8K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040217K8FKED 50

112 ERF8 Series, Board to Board EDGE RATE Rugged HS, 20 x 2Rows 7.0mm Lead Style, 0.8mm pitch, SMD Socket Make: SAMTEC ERF8-020-07.0-L-DV-K-TR 12

113 ERF8 Series, Board to Board EDGE RATE Rugged HS, 20 x 2Rows 5.0mm Lead Style, 0.8mm pitch, SMD Socket Make: ERF8-020-05.0-L-DV-K-TR 12

114 ERM8 Series, Board to Board EDGE RATE Rugged HS, 20 x 2Rows 2.0mm Lead Style, 0.8mm pitch, SMD Receptacle Make: SAMTEC ERM8-020-02.0-L-DV-P-TR 12

115 ERM8 Series, Board to Board EDGE RATE Rugged HS, 20 x 2Rows 5.0mm Lead Style, 0.8mm pitch, SMD Receptacle Make: SAMTEC ERM8-020-05.0-L-DV-K-TR 12

116 10 Pin Header Connector- receptacle 0.050 (1.27mm) Pitch Surface mount gold Make: Samtec Inc SFML-105-02-L-D-K-TR 10

117 10 Pin Header Connector, 2rows*5 PIN Shrouded Through Hole Make: SparkFun Electronics PRT-08506 10

118 CON16AP, WR PHD 1.27mm DUAL SMT PIN Header Surface Mount 16 positions Make: Wurth Electronik 62131621021 10

119 CON3 CONN HEADER Through Hole,Right Angle 3 position, 2.54MM09 Make: Samtec Inc. IPL1-103-01-F-S-RA-K 10

120 LED ,GREEN CLEAR, 0603 SMD, Discrete 2V Make:Wurth Electronik 150060VS75000 12

121 MARL R/A BICOLOR LED 151 Series Make: MARL 151-535-04 10

122 Bi Color LED 8mm PNL MNT RED/GREEN 2vdc IP67 ,20mA Make: APEM Inc Q8R5GYYRG02E 2

123 LED GREEN,CLEAR, 0603 SMD ,Discrete 2V Make: Wurth Electronik 150060VS75000 10

124 TVS DIODE BI-DIR Surface Mount, D0-214AB, 85V Clamp, 53VWM Make: Bourns Inc 1.5SMC62A 10

125 SCHOTTKY Diode 20V 3A SMA Make: Diode Instruments B320A-13-F 30

126 DIODE SCHOTTKY ,30V 100MA SOD-323 Make: Central Semiconductor Corp CMDSH-3 TR PBFREE 15

127 TVS DIODE,162V clamp ,3.7A lPP ,100VWM ,DO-214AA Make: Taiwan Semiconductor corporation SMBJ100A 10

128 DIODE GEN PURP ,50V , 1A surface mount DO-214AC Make: Onsemi ES1A 20

129 DIODE SCHOTTKY 60V,1A,Surface Mount SMA Make: Onsemi SS16T3 10

130 TVS DIODE ,9.2V clamp,5VWM,65.2A IPP ,Surface Mount, DO-214AA Make: Taiwan Semiconductor Corporation SMBJ5V0A 10

131 Fixed IND,68uH unshielded drum core,230MA, 6.7ohm, wirewound inductor, 0805 SMD Make: Murata Electronics LQH2MPN680MGRF 15

132 Ferrite Bead, 60ohms @100MHz,1 Power Line,6A,9m ohm,1806 ILN Make: Murata Electronics BLM41PG600SN1L 20

133 10ohms@100MHz 1 Ferrite bead,1A,25m ohm,0402 Make: Murata Electronics BLM15AG100SN1D 20

134 Fixed Shielded multilayer inductor,1.8uH,50mA,850m ohm SMD 0603 Make: TDK Corporation MLF1608A1R8KTD25 50

135 1 single line Ferrite Bead,5ohms@100mHz,700mA,70m ohm,0805 Make: Wurth Electronik 742792005 50

136 Fixed Ind 600nH shielded molded inductor,17.7A,4.52M ohm Make: Colicraft XAL5030-601MEC 15

137 Fixed Ind,1.2uH shielded drum core,wirewound inductor 11a,9.7m ohm Make: Bourns Inc SRP5030CA-1R2M 15

138 Power Inductors, 4.7uH,±20%, 54mohm, 4.8A SMD Make: SMIDA America Components Inc 0624CDMCCDS-4R7MC 15

139 32-bit ARM Cortex-M4/M0+ microcontroller with 256KB Flash Memory PACKAGE Make: NXP LPC54101J256BD64QL 5

140 32-bit ARM Cortex-M4/M0+ microcontroller with 512KB Flash Memory Make: NXP LPC54101J512BD64QL 6

141 Local Temperature Sensors with ±0.5°C accuracy from -40°C to +105°C,8 TDFN-EP* Make: Maxim Integrated MAX31725MTA+ 8

142 Dual, Current Feedback,8-Lead Plastic SOIC Low Power Op Amp Make: Analog Devices AD812ARZ 10

143 Integrated Triple Video Filter with Selectable Cutoff Frequencies for RGB, HD/SD ,20-Lead QSOP Make: Analog Devices ADA4412-3ARQZ 15

144 ADV7403-LQFP100 -12-Bit, Integrated, Multiformat SDTV/HDTV Video Decoder and RGB Graphics Digitizer Make: Analog Devices ADV7403 7

145 ADV7393-LFCP40 -Low Power, 10-Bit SD/HD Video Encoder Make: Analog Devices ADV7393 10

146 AD8062-MSOP8 - 300 MHz Rail-to-Rail Amplifiers Make: Analog Devices AD8062ARMZ 12

147 24BIT VIDE Encoder VID 69 -All-Format Oversampled Component Video/PC Graphics D/A System With Three 11-Bit DACs Make: Texas Instruments THS8200IPFPEP 10

148 AD8244BRMZ -Precision FET Input Quad Buffer,10-Lead MSOP Make: Analog Devices AD8244BRMZ 10

149 ADA4411-3ARQZ- Integrated Triple Video Filter and Buffer with Selectable Cutoff Frequencies and Multiplexed Inputs for RGB, HD/SD,24-Lead QSOP Make: Analog Devices ADA4411-3ARQZ 12

150 AD8146-LFCP24- Triple Differential Driver for Wideband Video Make: Analog Devices AD8146 12

151 SN74HC365PWR-Hex Buffers and Line Drivers with 3-state output,TSSOP Make: Texas Instruments SN74HC365PWR 10

152 DS1818R-5+T&R -3.3V EconoReset with Push Buttons,SOT23 Make: Maxim Integrated DS1818R-5+T&R 10

153 SP336EEY-L - 3.3V / 5V PROGRAMMABLE RS-232/485/422 SERIAL TRANSCEIVER,28-pin TSSOP Make: Exar Corporation SP336EEY-L 12

154 MAX14591ETA+T -High-Speed, Open-Drain Capable Logic-Level Translator,8 TDFN Make: Maxim Integrated MAX14591ETA+T 10

155 AD725-SOIC16 -RGB to NTSC/PAL Encoder with Luma Trap Port Make: Analog Devices AD725ARZ 10

156 PI6CV2304-SOIC8- IC CLK Buffer,1:4,140MHz 8-SOIC Make: Diodes INC/Pericom PI6CV2304WE 10

157 EL4581-SOIC8 -IC Video Sync Seperater Make: Renesas EL4581CSZ 10

158 1024K I2C Serial EEPROM_SOP_SOIC Make: Microchip 24AA1026-SN 10

159 THS7316D -3-Channel HDTV Video Amplifier With 5th-Order Filters and 6-dB Gain 8-SOIC Make: Texas Instruments THS7316DR 15

160 BNX022-01 - Block Type EMIFIL LC Combined Type Make: Murata BNX022-01 10

161 LM5050MK-2 -High Side OR-ing FET Controller Make: Texas Instxruments LM5050MK-2 10

162 AD812ARZ_SOIC-Dual, Current Feedback Low Power Op Amp Make: Analog Devices AD812ARZ 10

163 SN74LVC3G04DCT_A -Triple Inverter Gate Make: Texas Instruments SN74LVC3G04DCT 10

164 FET7A_PQFN -Dual, Current Feedback Low Power Op Amp Make: Fairchild FDMS86250 10

165 CDSOD323-T36SC -TVS Diode Series Make: Bourns CDSOD323-T36SC 12

166 IP_ProtectionIC_ADM1270ARQZ -High Voltage Input Protection Device Make: Analog Devices ADM1270ARQZ-R7 10

167 LTC3636EUFD -Dual Channel 6A, 20V Monolithic Synchronous Step-Down Regulator Make: Analog Devices LTC3636EUFD 10

168 SEMI LT3479 DC Switching Inverter -3A, Full Featured DC/DC Converter with Soft-Start and Inrush Current Protection Make: Linear Technology LT3479EFE#PBF 14

169 OSC_28.63636MHz, ±50PPM,-40 to 105Deg Make: ECS Inc ECS-286.3-20-3X-EP-TR 10

170 OSC_32.768KHZ CRYSTAL Make: Micro CrystalSwitzerland CC7V-T1A32.768KHZ+-20PPM_TBQA 10

171 OSC_17_734MHZ, 07050 size Make: Aandhra Electronics CXO7050LM3N017M7340000 15

172 ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 and STLINK/V2-ISOL features with digital isolation Make: ST Micro Electronics ST-LINK/V2-ISOL 2

173 N-Ch MOSFET,20V,1.3A,SOT23-3 Make: Onsemi NDS331N 10

174 Feed through capacitor,1.5uF,25V,1806 Make: Murata Electronics NFM41PC155B1E3 30

175 Banana jack connector, 5.5mm Make: KEYSTONE Electronics KEYSTONE 575-4 2

176 N-Ch MOSFET,60V,TO263-3 Make: Infineon Technologies SPB80P06PG 20

177 NPN BJT,40V,0.2a,SOT23-3 Make: Onsemi MMBT3904LT1G 20

178 USB-ML universal Programmer for ARM 8/16/32 bit devices Viz LPC 5400series Make: NXP/PE micro devices U-Mulitilink /USB-ML-Universal 1

3 LIST OF DELIVERABLES • As per Section 2 above • OEM or OEM Authorized Distributor CoC / Type approval Certificate • Technical document (if applicable) Important Note: Components without OEM or OEM Authorized Distributor CoC / Type approval Certificate are liable for REJECTION

4 DELIVERY SCHEDULE Delivery shall be done within 06 weeks from the date of placement of PO. Bidders shall ensure that maximum lead time shall not be more than 12 weeks.

HINDUSTAN AERONAUTICS LIMITED MCSRDC Division Marathalli Post Bangalore - 560 037 INDIA

COMMERCIAL TERMS AND CONDITIONS (FOR INDIGENOUS SUPPLIER) OF TENDER - PART OF TECHNICAL BID

Tender Ref. No. MC/S461/2158/24/1

Name of Work: Electronic Components - 178 types

Type of Bid: Single Bid System

Name of the Vendor/ Firm:

Quotation Ref. No.:

PLEASE INDICATE YOUR RESPONSE/ COMPLAINCE/ ACCEPTANCE TO THE FOLLOWING TERMS (MANDATORY) AND UPLOAD AS A PART OF TECHNICAL BID

Sl. No RFQ terms & conditions Vendor Compliance (remarks wherever required)

1 Tender Due Date: The due date for submission of quote is as indicated in RFQ through e-procurement mode only.

2 Validity of the Quotation: Price quoted should be net and unless otherwise specified should remain valid for our acceptance for a minimum of 90 days from the closing date of enquiry and the materials / service offered should be perfectly kept under provisional reservation for this quotation.

3 Submission of Tender: a) Response to bid through HAL e-Procurement portal should be uploaded in the e-Portal only. Bid submitted by bidder’s authorized dealer / distributor/channel partner should accompany with ink signed / digitally signed authorization letter of the bidder to whom tender has been originally issued. In the absence of authorization letter, the bids submitted shall be considered as unsolicited. b) Vendors should ensure the bids are submitted as per RFQ well before due date and time of tender. Vendor may note technical bid should include technical aspects only. If prices are indicated in the technical bid or attached as a part of technical bid even in the form of PDF, the offer will not be considered for evaluation.

4 Late Tender: a) Bid received after the due date and time specified in the tender shall be considered as late tender and will not be considered. HAL e-portal does not allow submission of Tender after the expiry of due date and time of the RFQ. b) HAL will not be responsible for inability of bidder to upload the tender documents in e-procurement. c) HAL reserves the right to reject late or incomplete tender.

5 Opening of Tenders: In respect of two bid system, technical bid will be opened on the tender opening date as indicated in the main RFQ. After technical evaluation, the Commercial bids of those bidders who are technically acceptable will be opened.

6 Tender Evaluation: a) L-1 (Lowest Bid) will be decided based on Line wise basis b) Bid with lowest price conforming to the specification will be considered for placement of Order. Appropriate loading shall be done on quoted prices in case bidder(s) deviate/non-comply with clauses such as Liquidated Damages, Security Deposit (SD) and Payment terms. Vendor with lowest price will be considered for placement of order after considering all taxes and charges (i.e., landed price) and after loading (if there is/are deviation(s)). c) If the bidder considers that tendered quantity is small, the bidder may quote for Minimum Ordering Quantity (MOQ). Commercial evaluation in this case will be done on MOQ x unit price, if MOQ offer beyond 20% of RFQ quantity. d) If two or more bidders quote the same price, HAL reserves the right to seek revised offer from the same bidders and placing order on revised L-1 offer. If same situation prevails then HAL reserve the right to place order on any of them. e) If the lowest bidder has not offered full quantity, for the balance quantity HAL reserves the right to source from other bidders on L1 price. f) Conditional discounts will not be considered in evaluation of tender. g) Applicability of the Taxes (IGST/CGST etc.) should be explicitly indicated by the bidder in his response either in percentage or in absolute terms. In the absence of this input the offer would be considered all inclusive.

7 Conflict of Interest: Any bidder having a conflict of interest, which substantially affects fair competition, shall not be eligible to bid in this tender. Bids found to have a conflict of interest shall be rejected as nonresponsive. A bidder in this Tender Process shall be considered to have a conflict of interest if the bidder: a) directly or indirectly controls, is controlled by or is under common control with another Bidder; or b) receives or have received any direct or indirect subsidy/ financial stake from another bidder; or c) has the same legal representative as another bidder for purposes of this bid. A Principal can authorize only one representative, and the representative also should not represent or quote on behalf of more than one Principal. However, this shall not debar more than one Authorised distributor from quoting equipment manufactured by an Original Equipment Manufacturer (OEM), in procurements under Proprietary Article Certificate; or d) has a relationship with another bidder, directly or through common third parties, that puts it in a position to have access to information about or influence the bid of another Bidder or influence the decisions of the Procuring Entity regarding this Tender process; or participates in more than one bid in this tender process; or e) Participation in any capacity by a Bidder (including the participation of a Bidder as sub-contractor in another bid or vice-versa) in more than one bid shall result in the disqualification of all bids in which he is a party. However, this does not limit the participation of a non-bidder firm as a sub-contractor in more than one bid; or f) would be providing goods, works, or non-consulting services resulting from or directly related to consulting services that it provided (or were provided by any affiliate that directly or indirectly controls, is controlled by, or is under common control with that firm), for the procurement planning (inter-alia preparation of feasibility/ cost estimates/ Detailed Project Report (DPR), design/ technical specifications, Terms of Reference (ToR)/ Activity Schedule/ schedule of requirements or the Tender Document etc.) of this Tender process; or g) has a close business or family relationship with a staff of the Procuring Organization who: i) are directly or indirectly involved in the preparation of the Tender document or specifications of the Tender Process, and/or the evaluation of bids; or ii) would be involved in the implementation or supervision of resulting Contract.

9 ARBITRATION: All disputes or differences whatsoever arising between the parties out of or relating to the construction, meaning and operation or effect of this Contract or the breach thereof shall be settled by Arbitration in accordance with the Rules of Arbitration of the ICA/ICADR/IIAC and the award made in pursuance thereof shall be binding on the parties. The provisions of the Arbitration and conciliation Act 1996 or any statutory modifications thereof shall apply to such conciliation.

10 Eligible Goods & Services: a) Country of Origin: The term “origin” used in this clause means the place from where the Services (and incidental Goods, including subcontracted components) are arranged and delivered, or manufactured.

11 b) Bidder’s country which shares a land border with India: Any bidder from a country, which shares a land border with India will be eligible to bid in this tender only if the bidder is registered with the Competent Authority (i.e. the registration committee constituted by the Department for Promotion of Industry and Internal Trader (DPIIT). However, the bidders from those countries (even if sharing a land border with India) to which the Government of India has extended lines of credit or in which the Government of India is engaged in development projects are not required to register with Competent Authority and will be eligible to bid in this tender. Bidder from a country, which shares a land border with India, for the purpose of this Order means:- i) An entity incorporated, established or registered in such a country; or ii) A subsidiary of an entity incorporated, established or registered in such a country; or iii) An entity substantially controlled through entities incorporated, established or registered in such a country; or iv) An entity whose beneficial owner is situated in such a country; or v) An Indian (or other) agent of such an entity; or vi) A natural person who is a citizen of such a country; or vii) A consortium or joint venture where any member of the consortium or joint venture falls under any of the above. Unless otherwise stipulated in the Contract, country of origin of ‘Services’ and related ‘Goods’ under the contract shall have their origin in India or other countries and must conform to the declaration, made by the Supplier in its bid regarding but not limited to any restrictions on certain countries with land-borders with India. The successful bidder shall not be allowed to sub-contract works to any contractor from a country, which shares a land border with India unless such contractor is registered with the Competent Authority.

12 c) Minimum Local Content: Minimum Local content (Make in India Policy): The ‘local content’ requirement to categorize a supplier as ‘Class-I local supplier’ is minimum 50%. For ‘Class-II local supplier’, the ‘local content’ requirement is minimum 20%. Nodal Ministry/ Department may prescribe only a higher percentage of minimum local content requirement to categorize a supplier as ‘Class-I local supplier/ ‘Class-II local supplier’. For the items, for which Nodal Ministry/ Department has not prescribed higher minimum local content notification, it shall be 50% and 20% for ‘Class-I local supplier’/ ‘Class-II local supplier’ respectively. Please refer the document - "Appendix_A_Purchase_Pref_Policy" for policy details Please indicate details of Local content and Category in Annexure-3 of RFQ That the bidder has to indicate MLC as part of offer & Self Certificate and Auditor Certificate might have also indicated MLC as per their certification. In case there is difference in those values, the lowest of them will be considered as the applicable MLC & the offer will be dealt accordingly. Other MLC information will be treated as invalid. Supplier’s status as MSEs: It is relevant to note that as per Government of India direction, the aspect of MSEs policies also included in the tender and the same is covered in the other terms & conditions which are part of RFQ. The aspect as indicated below would be applicable for procurement which falls under indivisible category (for each line). a) As per the Policy, Micro and Small Enterprises (MSE) Following shall be followed subject to the quoted price of MSE falls within the price band of L1+15% and such MSE agrees to match with L1 price (where L1 is non-MSE vendor): i. In case the tendered item fall under splitable/divisible category, the MSE shall be allowed to supply 25% of total tendered quantity. ii. In case the tendered item fall under non-splitable/ non-divisible category, the MSE shall be allowed to supply 100% of total tendered quantity. Concurrent application of public procurement policy for both MII and MSE shall be governed as per the OM vide No. F.1/4/2021-PPD dated 18/05/2023 from PPD, DoE, MoF.

13 Non-conformities between Figures and Words: In case of non-conformities/errors are observed in responsive tenders between the quoted prices in figures and in words. The same shall be resolved in the following manner, discretion of HAL in this regard is Final: a) If, in the price structure quoted for the required goods / services, there is discrepancy between the unit price and total price (which is obtained by multiplying the unit price by the quantity), the unit price shall prevail and the total price corrected accordingly; b) If there is an error in a total corresponding to the addition or subtraction of sub-totals, the sub-totals shall prevail and the total shall be corrected; and c) If there is a discrepancy between words and figures, the amount in words shall prevail. Such a discrepancy in an offer should be conveyed to the bidder asking him to respond by a target date and if the bidder does not agree to HAL's observation, then the bid is liable to be rejected. d) Such a discrepancy in an offer should be conveyed to the Bidder asking him to respond by a target date and if the Bidder does not agree to HAL’s observation, the bid is liable to be rejected.

A Clauses with regard to Supplies:

1 Packing: The Vendor will be held responsible for the stores being sufficiently and properly packed for tropical storage and for transport by rail, road, sea or air so as to ensure their being free from loss or injury on arrival at their destination. The packing and marking of packages shall be done by and at the expense of the vendor. Each package shall contain a Packing Note quoting Purchase Order number and date showing its contents in detail. Each shall be properly marked with Purchase Order No., Consignee’s name & address, packagehandling instructions etc. The package shall have adequate provision for handling during transit.

2 Receipt & Despatch: The Vendor is responsible for obtaining a clear receipt from the Transport Authorities specifying the goods dispatched. He will not book any consignment on a said to contain’ basis. If he does so, he does it on his own responsibility. HAL will take no responsibility for short deliveries or wrong supply of goods when the same are booked on said to contain’ basis. HAL shall pay for only such stores as are actually received by them in accordance with the contract.

3 Quantity: a) The quotation must be in the unit in which the quantity is indicated in the enquiry. If it is otherwise, conversion data must be furnished. b) HAL reserves the right to order quantity less than indicated in the enquiry/ quoted for by bidder, at the prices quoted, without any reference to the bidder

4 Inspection, Consequences of Rejection: The goods on receipt in HAL will be subject to inspection and tests, if necessary and HAL inspector’s decision as regards acceptance/rejection of goods shall be final and binding between the parties. (In case of Plant & Machinery, goods shall be finally inspected & accepted only after successful commissioning) If any stores are rejected, then HAL shall be at liberty to: a) Either: i) Allow the contractor to re-submit stores in replacement of those rejected within a time specified by HAL, the contractor bearing the cost of freight in such replacement without being entitled to any extra payment, (or) ii) Buy the quantity of stores rejected or other of a similar nature elsewhere at the risk and cost of the contractor without effecting the contractor's liability as regards the supply of any further consignments due under the contract, (or) iii) Terminate the contract and recover from the contractor the loss HAL may thereby incur. The contractor shall not be entitled to any gain on the repurchase, b) Any stores rejected by HAL’s Inspector must be removed by the contractor within 14 days from the date of receipt of intimation of rejection and at his own cost, failing which the contractor shall be liable to pay storage charges at 1% for each day of delay on the invoice value of the stores. If the stores are not removed within a month from the date of intimation of rejection, the stores will be liable, to be sold by HAL at the contractor’s risk and responsibility and the proceeds adjusted towards storage charges. c) In case any payment is made against delivery and it is found that the supplied item is rejected during inspection/commissioning, contractor will be required to choose any one of the following options to collect the rejected item for replacement: i) Refund the amount paid and collect the item for replacement. ii) Submit a Bank Guarantee for the amount already paid and collect the item for replacement. iii) Bring the replacement item to HAL and collect the rejected item.

5 Deliveries, Consequences of Breach: The date of delivery stipulated in the Purchase Order shall be deemed to be the essence of the Contract, and delivery must be completed on or by the dates mentioned in the Purchase Order or the tender. Should the Vendor fail to deliver the stores or any consignment thereof within the period prescribed for such delivery, HAL shall be entitled at their option: a. To recover from the Vendor as per liquidated damages, and not by way of penalty, a sum of 0.5% of the price of any stores which the contractor has failed to deliver as aforesaid, for each week or part thereof during which the delivery or such stores may be in arrears subject to a maximum of 10% of the price of the stores in default (or) b. To purchase elsewhere, with or without notice to the Vendor on the account and at the risk of the Vendor, the stores not delivered or others of a similar description (where other exactly complying with the particulars are not available), HAL’s decision in this respect will be final (or) c. To terminate the contract in the event of action being taken under Para – (a) & (b) above, the Vendor shall be liable for any loss which HAL may sustain on the account, but the Vendor shall not be entitled to any gain on repurchases made against default.

6 Extension of Time: If an extension is desired by the Vendor/Supplier, then Vendor/Supplier shall apply for extension of time to HAL at least 15 days prior to the date of delivery without prejudice to the rights of HAL, then HAL may grant extension of time for any cause which HAL may deem proper and the decision of HAL in this respect to be final and binding and cannot be questioned in any manner whatsoever.

B Clauses related to available Recourse for Breach by Supplier:

1 Liquidated Damages: In the event of an order, we reserve the right to collect a sum of 0.5% per week (on basic cost only excluding taxes & duties, if such details are furnished separately in the bid submitted) of delay or part thereof, subject to a maximum of 10% as our claim-towards liquidated damages on the undelivered part of the order. Note: In case bidders does not agree with Liquidated Damages, loading factor to the extent of LD not agreed shall be considered while preparing Price Comparative Statement and offer will be evaluated accordingly.

2 Penalties for Misdemeanours: (Note: The below sub clause (a) and (c) both are applicable before execution of the contract or placing of Purchase Order on a successful bidder and (b) shall be applicable only after execution of contract or placing of Purchase Order.) Without prejudice to and in addition to the rights of the HAL to other remedies as per the Tender-documents or the contract, If the HAL concludes that a (prospective) bidder/ Supplier directly or through an agent has committed a misdemeanor in competing for the tender or in executing a contract, the HAL shall be entitled, and it shall be lawful on his part to take appropriate measures, including the following:

a) If Bidder/s bids are under consideration in any procurement: i) Enforcement of Bid Securing Declaration in lieu of forfeiture or encashment of Bid Security. ii) Calling off of any pre-contract negotiations, and; iii) Rejection and exclusion of Bidder from the Tender Process b) If a contract has already been awarded: i) Termination of Contract for Default and availing all remedies prescribed thereunder; ii) Encashment and/ or Forfeiture of any contractual security or bond relating to the procurement; iii) Recovery of payments including advance payments, if any, made by the HAL along with interest thereon at the prevailing rate;

3 c) Remedies in addition to the above: i) In addition to the above penalties, the HAL shall be entitled for any of the following action/s, and it shall be lawful on his part to: File information against Bidder or any of its successors, with the Competition Commission of India for further processing, in case of anti-competitive practices; ii) Initiate proceedings in a court of law against Bidder or any of its successors, under the Prevention of Corruption Act, 1988 or the Indian Penal Code or any other law for transgression not addressable by other remedies listed in this sub-clause. iii) Remove Bidder or any of its successors from the list of registered suppliers for a period not exceeding two years. Suppliers removed from the list of registered vendors or their related entities may be allowed to apply afresh for registration after the expiry of the period of removal. iv) Initiation of suitable disciplinary or criminal proceedings against any individual or staff found responsible. v) Debar a bidder/ Supplier from participation in future procurements without prejudice to HAL’s legal rights and remedies. Debarment shall automatically extend to all the allied firms of the debarred firm. In the case of Joint Venture/ consortium, all its members shall also stand similarly debarred: HAL may debar a bidder or any of its successors from participating in any Tender Process undertaken by all its procuring entities for a period not exceeding two years commencing from the date of debarment for. HAL shall maintain such a list which shall also be displayed on their website. HAL may debar a bidder from participating in any Tender Process undertaken for a period not exceeding three years commencing from the date of debarment for misdemeanors. HAL shall maintain such a list which shall be circulated to all its Divisions.

4 Exit Clause: Exit criteria: The contract/order may be terminated under the following circumstances: i) In the event of unsatisfactory performance by the Seller during the contract period, or any of the information provided by the Seller is found to be untrue, or Seller is found to have attempted to influence any person involved with the contract through unethical means, the contract shall be terminated with 03 months advance notice without any financial implication to Buyer. Notwithstanding the foregoing, in cases where it is found that a Seller is engaged in unethical practices, they shall be barred from participating in the future contracts for a period of 02 years. ii) If there is change in Buyer requirement, contract shall be terminated with 03 months advance notice. The liability of Buyer in this case will be agreed mutually. In the event of termination of contract by either party the Seller shall ensure the following: a) IPR’s are transferred to Buyer to enable Buyer to proceed on the work with other Seller. Seller also will render all assistance till the other Seller fully take over the balance work. (If applicable) b) Transfer title and deliver all or any part thereof of the supplies, materials, work-in-progress, finished Products, Tooling, drawings and data produced or acquired by Seller specifically for the Product being terminated. c) Supply of products and its components / spares at least for a period of 10 years from the date of such termination. iii) The Seller is declared bankrupt or becomes insolvent. iv) The delivery of material is delayed due to causes of Force Majeure by more than 06 months. v) Based on the decision of the Arbitration Tribunal

5 a) Termination for Default of Seller or for other reasons: HAL shall have the right to short close present Contract in part or in full by giving 1 month prior notice to the Supplier, in any of the following cases:- a) The work is delayed or cancelled for causes attributable to force majeure. b) The requirement is withdrawn by HAL’s Customer. c) The Supplier is declared bankrupt or becomes insolvent. d) It is noticed that the firm has utilized the services of any agent to get the resulting Order and paid any commission to such agent. e) As per decision of the Arbitration Tribunal. f) In case any part of the Order is subcontracted by the Supplier without prior permission of HAL. g) If the performance of the Supplier is not found satisfactory during the execution of work. In any of the above stated case, no claim of damage etc., by the Supplier will be allowed.

b) Termination for Default of Either of the Party (mutual termination): Either of the Party shall have the right to short close present Contract in part or in full by giving 1 month prior notice to the other Party, in any of the following cases:- a) The work is delayed or cancelled for causes attributable to force majeure. b) The requirement is withdrawn by the end Customer. c) Either of the Party is declared bankrupt or becomes insolvent. d) It is noticed that either of the Party has violated/breached the Integrity. e) As per decision of the Arbitration Tribunal. f) Either of the Party has assigned the contract to a third party without prior permission from other party. g) If the performance of either of the Party is not found satisfactory to the other Party during the execution of work. In any of the above stated case, no claim of damage etc., by the defaulting Party will be allowed.

6 Risk purchases: The Supplier will supply quality items as per approved sample and also the quantity intended by the concerned Division in full as per terms and conditions of respective orders. In case the Supplier fails to execute the order either in terms of quality or in quantity, HAL reserves the right to procure from elsewhere at the risk and cost of the Supplier and any extra expenditure incurred due to this purchase is payable by the Supplier.

C Mandatory Clauses as per Ministry or Govt. of India:

1 Bribes and Gifts Any bribe, commission, gift or advantage given, promised or offered by or on behalf of the Vendor or his parties, agent or servant or any one on his or their behalf to any officer, servant, representative or agent of HAL or any person on his or their behalf in relation to the obtaining or to the execution of this or any other contract with HAL shall in addition to any criminal liability which the Vendor may incur, subject to the Vendor to the cancellation of this and all other contracts with HAL and also to payment of any loss or damage resulting from any such cancellation thereof. Any question or dispute as to the commission of any offence under the present clause shall be settled by HAL in such manner and on such evidence or information as they may think fit and sufficient and their decision shall be final and conclusive.

2 Immunity to Government of India It is understood and agreed that the Government of India is not a party to this agreement and has no liabilities, obligations or rights hereunder. It is expressly understood and agreed that HAL is an independent legal entity with power and authority to enter into contracts solely in its own behalf under the applicable Laws of India and General Principles Contract Law. The vendor shall agree, acknowledge and understand that HAL is not an agent, representative or delegate of the Government of India. It is further understood and agreed that the Government of India is not and shall not be liable for any acts, omissions, commissions, breaches or other wrongs arising out of the contract. Accordingly, vendor expressly waives releases and foregoes any and all actions or claims against the Government of India arising out of this contract, not to sue the Government of India as to any manner, claim, and cause of action or thing whatsoever arising out of or under this agreement

3 Agents/Agency Commission (Note: HAL has not appointed/authorized any person/agent to deal with the vendors in respect of the said contract. In case, if someone claims and interacts with the vendors it shall be duty of the vendors to bring such instances to the notice of HAL Management). The vendor confirms and declares to the Buyer that the vendor is the original manufacturer or authorized distributor/stockist of original manufacturer or Govt. Sponsored/ Designated Export Agencies (applicable in case of countries where domestic laws do not permit direct export by OEMs) of the stores referred to in this offer/contract/Purchase order and has not engaged any individual or firm, whether Indian or Foreign whatsoever, to intercede, facilitate or in any way to recommend to Buyer or any of its functionaries, whether officially or unofficially, to the award of the contract/purchase order to the vendor; nor has any amount been paid, promised or intended to be paid to any such individual or firm in respect of any such intercession, facilitation or recommendation. The vendor agrees that if it is established at any time to the satisfaction of the Buyer that the present declaration is in any way incorrect or if at a later stage it is discovered by the Buyer that the vendor has engaged any such individual/firm, and paid or intended to pay any amount, gift, reward, fees, commission or consideration to such person, party, firm or institution, whether before or after the signing of this contract/ purchase order, the vendor will be liable to refund that amount to the Buyer. The vendor will also be debarred from participating in any RFQ/ Tender for new projects/program with Buyer for a minimum period of five years. The Buyer will also have a right to consider cancellation of the Contract/ Purchase order either wholly or in part, without any entitlement or compensation to the vendor who shall in such event be liable to refund all payments made by the Buyer in terms of the Contract/ Purchase order along with interest at the rate of 2% per annum above Secured Overnight Financing Rate (SOFR) (for foreign vendor) and Marginal Cost of Funds-based Lending Rate (MCLR) of State Bank of India plus 2% per annum (for Indian vendor). The Buyer will also have the right to recover any such amount from any contracts/ Purchase order concluded earlier with Buyer.

4 Make In India Considering the huge and continuous requirement, HAL suggests the successful bidder to explore the possibility of manufacturing of the offered items in India to promote Govt. of India’s Make in India Policy. At this stage, HAL proposes to buy the systems/ items directly from the bidder for the firm requirement indicated above. However, for anticipated/future requirement, HAL requests successful bidder to submit the roadmap/proposal for HAL’s review for manufacturing of the offered system/item in India by setting up manufacturing facility in India or through joint venture in India.

5 Fall Clause The price quoted shall be in no event exceed the lowest price at which you sell the supplies or offer to sell supplies of identical description for similar quantity/terms to any person(s)/ organization including the purchases by any department of the Govt. of India, the State Govt. or any statutory undertaking of the Govt. of India/ State Govt., as the case may be during the period till the completion of the performance of the order placed and during currency of the order. If at any time during the said period, the contractor reduces the sales price, sells or offers to sell such supplies to any person/ organization including the purchaser or any department of Central Govt. or any Dept. of State Govt., or any statutory undertaking of the Central or State Govt., as the case may be at a price lower than the price chargeable under the contract, Seller shall forthwith notify such reduction/ sale or offer to sale to the HAL and the price payable under the contract for the supplies supplied after the date of coming into force of such reduction or sale or offer to sale shall stand correspondingly reduced.

D Payment related clauses:

1 Payment terms applicable for MSMEs: HAL is registered on TReDS platform (Trade Receivable Discounting Systems), as being promoted by GOI directives. It is suggested that all the MSME Vendors to take note of the same and consider for registration on any TReDS platform and avail the platform services which is being made available as per Government initiative.

2 Firm Prices The contract prices will be firm and fixed as per contract terms till execution of contract and exclude subsequent claims or price increases of any kind.

3 Payment For Stores/Supplies: Unless otherwise agreed to between the parties, HAL will effect payment for the delivery of the stores by Electronic Bank Transfer (ECE/RTGS) to the supplier’s bank account as notified to HAL on submission of bills in triplicate. Payment for the stores on each delivery will be made to the contractor after goods are received and passed by inspection. Normally 30 days will be allowed forinspection afterreceipt of goods.

4 Statutory Variation Clause: Unless otherwise stated in the contract, statutory increase in applicable GST rate only during the original delivery period shall be to Procuring Entity’s/Buyer account. Any increase in the rates of GST beyond the original completion date during the extended delivery period shall be borne by the Supplier. The benefit of any reduction in GST rate must be passed on to the Procuring Entity/Buyer during the original and extended delivery period. However, GST rate amendments shall be considered for quoted HSN code only, against documentary evidence, provided such an increase of GST rates takes place after the last date of bid submission.

E Confidentiality and IPR related clauses:

1 IPR Clause for indemnification of HAL in case of Infringement of Third Party IPR: HAL shall have the right to use the Supplies/Services procured under the contract that may contain any Intellectual Property/ Intellectual Property Rights. Seller shall indemnify and protect at its own cost, HAL in respect of cost/claims/ liabilities (including attorney’s fees) arising from any violation of Intellectual Property Rights of any third party with respect to Supplies/Services provided by Seller. If HAL or HAL’s customer/s are unable to put to use the Supplies/Services or a portion thereof as a result of violation of the Intellectual Property of any third party, Seller shall within reasonable time at Seller’s own cost either, i) procure for HAL and HAL’s Customer/s the right to continue using the Supply/Service or, ii) replace or modify the Supplies/Services so that it becomes non-infringing or, iii) compensate HAL the amount equivalent to the cost of supplies procured/ to be procured, development cost already paid to seller and damages suffered by HAL arising due to inability to put to use the supplies/ services or a portion thereof. Intellectual Property for the purpose of this clause includes inventions, discoveries and improvements; know-how, works of authorship, technical data, drawings, specifications, process information, reports and documented information; and computer software(including without limitation, source code, object code, source code listings and object code listings that would enable the software to be reproduced or recreated), topology of integrated circuits, databases or any other such results of intellectual activity

1 Tender conditions: a) Any order, resulting from the enquiry, shall be governed by the General Terms and Conditions of Contract of HAL and any party quoting against this enquiry shall be deemed to have read and understood these terms and conditions and to have quoted subject to these terms and conditions (Tender Documents as enclosed in this RFQ). b) When counter terms and conditions have been offered by a tenderer, HAL shall not be deemed to be governed by such terms and conditions unless specific written acceptance thereof has been given by HAL. c) Any terms & conditions which has not been the part of the bid or Purchase Order, if put forward in subsequent correspondence, shall not be considered by HAL. d) Disregard of any instructions, may result in your offer being ignored. e) Canvassing by tender form, including unsolicited letter on tender submitted or post tender corrections shall render their tenderers liable for rejection

2 Price: The bidder is required to indicate prices against individual items. a) Price quoted should be on F.O.R. MCSRDC-HAL, Bangalore for delivery at HAL Stores inclusive of all charges including transit insurance. b) Indian Bidder should quote in Indian Rupees and payment will be made in Indian Rupees. c) Tenderers should clearly mention whether the prices hold good when the full quantity of enquiry is not ordered but only a part of it. Unless otherwise mentioned, it would be assumed that the rates hold good even when lesser quantities than those enquired of are ordered. Any increase in prices at a later date for ordering lesser quantities will not be agreed to.

3 Taxes: Rate of GST HSN code/ SAC or any other Tax chargeable should be clearly indicated in the offer / bid as inclusive in the price quoted or extra. If not indicated, HAL will assume that the rates quoted are inclusive of taxes.

4 Delivery Period: Delivery shall be done within 06 weeks from the date of placement of PO

5 Terms of Payment: In the event of an order, 100% payment within 30 days on receipt and acceptance of individual line item. Payment will made by RTGS or any other latest Electronic Payment remittance mode.

6 Denial Clause: In case of any delay in delivery caused due to default of the Vendor and during such delayed period if any increase in statutory duties and/or upward rise in prices due to the Price Variation Clause (PVC) and/or any adverse fluctuation in foreign exchange arises then such additional amount/s is/are to be borne by the Vendor, apart from the payment of agreed Liquidated Damages. Besides HAL reserves its right to get any benefit of a downward revisions in statutory duties, PVC and foreign exchange rate, taken place during such delayed period, effecting the original agreed price.

7 DOCUMENTS: Following documents where ever applicable should be submitted along with the bid 1. GST Regsitration Certificate 2. HAL Vendor resgistration Certificate 3. ECS Mandate 4. MSME Resgistration on UAM portal (if applicable) 5. Authorised Distributor Certificate from OEM (if applicable)

8 Government e-Marketplace (GeM) registration: Any bidder participating in the tender should also got registered in GeM portal and should provide GeM seller ID as a part of their offer. In case, such GeM seller ID not provided as a part of their offer, supplier need to take up with GeM Authority for onboarding on GeM portal and provide such details, which will be necessary requirement for placement of order by HAL for this tender.

Indicate your GeM registration Number

9 Declaration of Non-supply of Counterfeit Products: The bidder has to comply and categorically indicate that the parts/product supplied is manufactured by OEM or through authorized distributor of OEM. Counterfeit parts/products should never be supplied. At any point if it is found that the part and/or product supplied are found to be counterfeit, penal actions as per company rules and existing laws may be initiated against the vendor.

10 ISO 45001:2018 STANDARD GUIDELINES: The vendor/Supplier/ contractor shall ensure requirements with respect to ISO 45001:2018 standard guidelines clause A 8.1.4. This includes equipment’s, installations and materials are safe for use by workers as intended by ensuring: a) equipment is delivered according to specification and tested to ensure it works as intended b) installations are commissioned to ensure they function as designed c) materials are delivered according to their specifications d) any usage requirements, precautions or other protective measures are communicated and made available (E.g. Safety instructions, Hazard communication Symbols, SDS, Etc.)

11 Debarred/ banned or blacklisted (Yes-Banned; No-Not banned)

12 Bidders to confirm whether, they have been debarred/ banned/ blacklisted or not by any Division/ Office of HAL/ PSE/PSU/CPSE/Ministry of Defence or any institutions/offices of State & central GOI. Also upload self certification for not banned status along with bid documents in portal. If at later stages its been found that your company is banned or blacklisted or if you have provided any false certification, suitable action will be initiated as deemed fit by HAL.

13 Please indicate following: Contact person name Postal address, email ID for future correspondence / clarifications and also provide email and phone no of CEO/MD/GM/Proprietor

Mission & Combat System Research & Design Centre HINDUSTAN AERONAUTICS LIMITED Marathalli Post Bangalore - 560 037 INDIA

Public Procurement (Preference to Make in India) - Part of Technical Bid - Annexure-3

Tender Ref. No. MC/S461/2158/24/1

Type of Bid: Single Bid System

Name of Work: Electronic Components - 178 types

Name of the Vendor/ Firm:

Quotation Ref. No.:

PLEASE INDICATE YOUR RESPONSE/ COMPLAINCE/ ACCEPTANCE TO THE FOLLOWING TERMS (MANDATORY) AND UPLOAD AS A PART OF TECHNICAL BID

Note In line with Public Procurement (Preference to Make in India), Order 2017 & its amendments issued by Govt. of India & with a view to support the Indian industries, HAL has implemented “Purchase Preference Policy”. The “Purchase Preference” is applicable for the “Class-I Local Supplier” for the goods/services/works covered in this tender subject to the following terms & conditions:

(a) The subject item falls under indivisible category (b) The offers sought only from Class-l & Class-Il local suppliers, out of local suppliers

Definitions: A supplier or service provider, whose goods, services or works offered for procurement, has local content: a. Equal to or more than 50% : Class-l local supplier. b. More than 20% but less than 50% : Class-II local supplier. c. Less than or equal to 20% : Non-local supplier.

Sl. HAL RFQ terms & conditions Vendor Compliance/ Remarks

1 a. Equal to or more than 50% : Class-l local supplier. b. More than 20% but less than 50% : Class-II local supplier.

Mention your category i.e., Class-l or Class-II local supplier

2 ‘Local content’ means the amount of value added in India (i.e. indigenous items/services added in the offered products/services/works) be the total value of the item offered (excluding net domestic indirect taxes) minus the value of imported content in the item (including all customs duties/IGST) as a proportion of the total value (excluding net domestic indirect taxes), in percent.

Indicate extent of Minimum Local Content in offered product/service and location of such value additions

3 Self-Certification and Auditor Certificate: i. The Class I & II local suppliers' should provide a “Self Certification” as per the format enclosed at Appendix-B(Type-I) along with technical offer indicating the % of local content along with details of the location(s) at which the local value addition is made along with the technical offer. ii. In cases the quoted price is in excess of Rs.10 Crs (including duties, taxes and freight & Insurance), the 'Class-l & II local supplier' shall provide a certificate as per the format enclosed at Appendix-B(Type-II) from the statutory auditor or cost auditor of the company (in the case of companies) or from a practicing cost accountant or practicing chartered accountant (in case of suppliers other than companies) indicating the percentage of local content along with the technical offer.

4 In case the offers sought from only class I & II local suppliers, the offer received without indicating the percentage of local content & without self-certification / Auditor Certificate (as applicable) will not be considered & rejected.

5 As mentioned above vendors shall enclose “Self Certification” / "Certificate from statutory auditor or cost auditor of the company" as applicable.

6 The ink-signed certificate shall be provided on vendor’s letter head along with the offer (in case of online tender, copy of ink-signed certificate can be considered subject to receipt of original certificate within 15 days of due date of tender). In case of non-submission of certificate, the purchase preference shall not apply.

Public Procurement (Preference to Make in India) policy in PDF form is enclsoed for your reference

Mission & Combat System Research & Design Centre HINDUSTAN AERONAUTICS LIMITED Marathalli Post Bangalore - 560 037, INDIA

Commercial Bid (PRICE FORMAT) - Annexure- 4

Tender Ref. No: MC/S461/2158/24/1

Name of Work: Electronic Components - 178 types

Single Bid System

Name of the Vendor/Firm

Address and Contact details

Quotation Ref. No and Date:

Sl. No. Product Description Part Number Qty (Nos.) HSN Code/ SAC Basic Unit Price Sub Total (Basic Unit Cost X Qty.) CGST SGST IGST Line Total along with all taxes

1 Ceramic CAP 0.1uF ±10%, 25V,X8R 0603 Make: Murata Electronics GCM188R91E104KA37D 100

2 Ceramic CAP 10uF ±20%, 10V,X5R 0603 Make: TAIYO YUDEN LMK107BJ106MALTD 100

3 Ceramic CAP 10uf ±10%, 16V,X7R 1206 Make: TDK Corporation C3216X7R1C106K160AC 100

4 Ceramic CAP 0.1uF ±10%,10V,X7R 0402 Make: Murata Electronics GCM155R71A104KA55D 550

5 Ceramic CAP 1nF ±10%,100V,X7R 0402 Make: Murata Electronics GCM155R72A102KA37D 50

6 Ceramic CAP 10nF ±10%,50V,X7R,0402, Make: Yageo AC0402JRX7R9BB104 100

7 CAP 0.82uf ±10%,25V,X7R 0805 Make: KEMET C0805C824K3RACAUTO 50

8 Ceramic CAP 47pF ±5%,50V,NP0 0402 Make: TDK Corporation CGA2B2NP01H470J050BA 50

9 Ceramic CAP 2.2nF ±10%,16V,X7R 0402 Make: KEMET C0402C222K4RACAUTO 50

10 CAP 12nF ±10%,16V,X7R 0402 Make: KEMET C0402C123K4RACAUTO 50

11 Ceramic CAP 0.15uf ±10%,25V,X7R 0402 Make: TDK Corporation CGA2B3X7R1E154K050BB 50

12 Ceramic CAP 22uf ±10%,16V,X7R 1210 Make: Murata Electronics GCM32ER71C226KE19L 50

13 Ceramic CAP 0.01uf ±10%,25V,X7R 0402 Make: KEMET C0402C103K3RACAUTO 100

14 Ceramic CAP 1uF ±10%,16V,X7R 0603 Make: KEMET C0603C105K4RACAUTO 50

15 Cerami CAP 47pF ±5% 16V, X8R ,0402 Make: KEMET C0402C470J4HACAUTO 50

16 Ceramic CAP 18pF, ±5% ,50V,NP0 0402 Make: TDK Corporation CGA2B2NP01H180J050BA 50

17 Ceramic CAP 12pF ±5%,50V,X8R 0402 Make: KEMET C0402C120J5HACAUTO 50

18 Molded Tantalum CAP 220uF ±10%,10V, 2917 Make: KEMET T491D227K010ATAUTO 50

19 Ceramic CAP 0.1uF ±10%,25V,X7R 0402 Make:TDK Corporation CGA2B3X7R1E104K050BB 50

20 Ceramic CAP 330pF ±10%,25V,X7R 0402 Make: KEMET C0402C331K3RACAUTO 100

21 Ceramic CAP 10uF ±10%,25V,X7R 1206 Make: KEMET C1206C106K3RACAUTO 50

22 Ceramic CAP 0.1uF 0.1uF ±10%,25V,X7R 1206 Make: KEMET C1206C104K3RACAUTO 50

23 Conformal coated tantalumCAP 100uF ±20%,35V,3024 Make: Vishay Sprague 597D107X0035F2T 50

24 Conformal coated tantalum CAP 47uF ±10%,50V, 3024 Make: Vishay Sprague 597D476X9050Z2T 50

25 Ceramic CAP 0.1uF ±10%,25V,X7R 1206 Make: YAGEO AC1206KRX7R8BB104 50

26 Ceramic CAP 4700pF ±10%,25V,X7R 0402 Make: KEMET C0402C472K3RACAUTO 50

27 Ceramic CAP ,100pF ±10%,25V,X8R 0603 Make: KEMET C0603C101K3HACAUTO 50

28 Ceramic CAP ,10nf ±10%,25V,X8G 0603 Make: KEMET C0603C103K3TACAUTO 50

29 Ceramic CAP ,10pF ±10%,16V,X8R 0805 Make: KEMET C0805C100K4HACAUTO 50

30 Ceramic CAP ,4.7uF ±10%,25V,X7R 0805 Make: KEMET C0805C475K3RACAUTO 50

31 CAP 0.1uF ±10%,25V,X8R 0603,MLCC Make: TDK CGA3E2X8R1E104K080A 50

32 CAP 1uF ±10%,100V,X7R 1206,MLCC Make: TDK CGA5L2X7R2A105K160AA 50

33 CAP 47uF ±20%,35V,X7R 2220,MLCC Make: TDK CGA9N1X7R1V476M230KC 50

34 CAP 1.5uF ±10%,100V,X7S 1206,MLCC Make: TDK CGJ5L3X7S2A155K160AA 50

35 Ceramic CAP,10pF ±10%,16V,X8R 0603 Make: KEMET CO603C100K4HACAUTO 50

36 Ceramic CAP, 33pF ±10%,16V,X8R 0603 Make: KEMET CO603C330K4HACAUTO 50

37 Ceramic CAP ,56pF ±10%,16V,X8R 0603 Make: KEMET CO603C560K4HACAUTO 50

38 Ceramic CAP, 47uF ±10%,6.3V,X6S 1206 Make: Murata Electronics GRT31CC80J476KE13L 50

39 Tantalum CAP, 100uF ±15%,10V,B-Case Make: KEMET T491B107K010ATAUTO 50

40 Ceramic CAP ,47uF ±10%,16V,X6S 1210 Make: Murata Electronics GRT32EC81C476KE13L 50

41 Ceramic CAP ,2.2uF ±10%,16V,X7S 0603 Make: Murata Electronics GRT188C71C225KE13D 50

42 Ceramic CAP ,1nF ±10% 100V,X7R 0603 Make: Murata Electronics GCM188R72A102KA37D 50

43 CAP 100nF,±10%,100V,X7S 0603,MLCC Make: TDKCorporation CGA3E3X7S2A104K080AB 50

44 Ceramic CAP,1uF±10%,16V,X8L 0805 Make: Murata Electronics GCM21BL81C105KA58L 50

45 Ceramic CAP, 2.2uF ±10%,25V,X7R 0805 Make: Murata Electronics GCM21BR71E225KA73L 50

46 Ceramic CAP ,10uF ±10%,25V,X7S 1206 Make: Murata Electronics GCM31CC71E106KA03L 50

47 Ceramic CAP, 15nF ± 10% ,25V, X7R 0402 Make: Murata Electronics GCM155R71E153KA55D 50

48 Ceramic CAP,0.1uF ±10%,16V,X7R 0402 Make: Murata Electronics GCM155R71C104KA55J 50

49 Ceramic CAP,10nF ±10%, 100V, X7R 0603 Make: Murata Electronics GCM188R72A103KA37D 50

50 RES 0E jumper chip resistor 1/10W, 0603 Make: Vishya Dale CRCW06030000Z0EA 650

51 RES 4.7K ±1% ,1/16W,0402 Make: Vishya Dale CRCW04024K70FKED 50

52 RES 0E jumper chip resistor 1/16W, 0402 Make: Vishay Dale CRCW04020000Z0ED 300

53 RES 560E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402560RFKED 100

54 RES 120Ohm_DNM ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402120RFKED 50

55 RES 10K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040210FKED 300

56 RES 634E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402634RFKED 50

57 RES 15K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040215K0FKED 50

58 RES 75 OHM ±1% ,1/16W,0402 Make: Vishay Dale CRCW040275R0FKED 450

59 RES 150E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402150RFKED 50

60 RES 33E ±1% ,1/16W,0402 Make: Vishay Dale CRCW040233R0FKED 200

61 RES 2.7K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04022K70FKED 50

62 RES 1.69K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04021K69FKED 50

63 RES 100E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402100RFKED 100

64 RES 5.6K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04025K60FKED 50

65 RES 1M ±1% ,1/16W,0402 Make: Vishay Dale CRCW04021M00FKED 50

66 RES 510E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402510RFKED 50

67 RES 1K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04021K00FKED 100

68 RES 169E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402169RFKED 50

69 RES 20K Ohm ±1% ,1/16W,0402 Make: Vishay Dale CRCW040220K0FKED 50

70 RES 2K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04022K00FKED 50

71 RES 787E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402787RFKED 50

72 RES 1.2K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04021K20FKED 50

73 RES 37.4E ±1% ,1/16W,0402 Make: Vishay Dale CRCW040237R4FKED 50

74 RES 59E ±1% ,1/16W,0402 Make: Vishay Dale CRCW040259R0FKED 100

75 RES 47K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040247K0FKED 50

76 RES 220E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402220RFKED 50

77 RES 330E ±1% ,1/16W,0402 Make: Vishay Dale CECW0402330RFKED 50

78 RES 36E ±1% ,1/16W,0402 Make: Vishay Dale CRCW040236R0FFKED 50

79 RES 39E ±1% ,1/16W,0402 Make: Vishay Dale CRCW040239R0FKED 50

80 RES 681K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402681KFKED 50

81 RES 470E ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402470RFKED 50

82 RES 0E jumper chip resistor 1/16W, 0805 Make: Vishay Dale CRCW08050000Z0EA 50

83 Thick film RES 5.62 ohm ,±1% 1206,100ppm,1/4W, Make: Vishay CRCW12065R62FKEA 50

84 Thin Film RES 1.5K ,±1%,0603,100ppm Make: Vishay M55342K12B1E50RTS 50

85 RES 470E ,±1%, 1/8W,0805 Make: Vishay CRCW0805470RFKEA 50

86 RES 7.68k ±1% ,1/16W,0402 Make: Vishay Dale CRCW04027K68FKED 50

87 RES 11k ±1% ,1/16W,0402 Make: Vishay Dale CRCW040211K0FKED 50

88 RES 100K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402100KFKED 50

89 RES 10 ±1% ,1/16W,0402 Make: Vishay Dale CRCW080510R0FKED 50

90 RES 200K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402200KFKED 50

91 RES 0.015E ,±1% ,15mohms,1/4W,1206 Make: Yageo RL1206FR-070R015L 50

92 RES 221K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402221KFKED 50

93 RES 2.99K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04022K94FKED 50

94 RES 29.4K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040229K4FKED 50

95 RES 80.6K ohm ±1% ,1/16W,0402 Make: YAGEO AF0402FR0780K6L 50

96 RES 13.7K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040213K7FKED 50

97 RES 4.99K ±1% ,1/16W,0402 Make: Vishay Dale CRCW04024K99FKED 50

98 RES 120K ±1%, 1/16W,0402 Make: Vishay Dale CRCW0402120KFKED 50

99 RES 332K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402332KFKED 50

100 RES 100E ±1% 1/10W, 0603 Make: Vishay Dale CRCW0603100RFKEA 50

101 RES 1.5K ohm ±1% ,1/16W,0402 Make: Vishay Dale CRCW04021K50FKED 50

102 RES 220K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402220KFKED 50

103 RES 270K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402270KFKED 50

104 RES 240Ohm ±1% 1/10W, 0603 Make: Vishay Dale CRCW0603240RFKEA 50

105 RES 84.5K ±1% 1/10W, 0402 Make: Panasonic Electronic Components ERJ-H2RF8452X 50

106 RES 14.7K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040214K7FKED 50

107 RES 30K_DNM ±1% ,1/16W,0402 Make: Vishay Dale CRCW040230K0FKED 50

108 RES 38K_DNM ±1% ,1/16W,0402 Make: Vishay Dale CRCW040239K0FKED 50

109 RES 18.7K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040218K7FKED 50

110 RES 402K ±1% ,1/16W,0402 Make: Vishay Dale CRCW0402402KFKED 50

111 RES 17.8K ±1% ,1/16W,0402 Make: Vishay Dale CRCW040217K8FKED 50

112 ERF8 Series, Board to Board EDGE RATE Rugged HS, 20 x 2Rows 7.0mm Lead Style, 0.8mm pitch, SMD Socket Make: SAMTEC ERF8-020-07.0-L-DV-K-TR 12

113 ERF8 Series, Board to Board EDGE RATE Rugged HS, 20 x 2Rows 5.0mm Lead Style, 0.8mm pitch, SMD Socket Make: ERF8-020-05.0-L-DV-K-TR 12

114 ERM8 Series, Board to Board EDGE RATE Rugged HS, 20 x 2Rows 2.0mm Lead Style, 0.8mm pitch, SMD Receptacle Make: SAMTEC ERM8-020-02.0-L-DV-P-TR 12

115 ERM8 Series, Board to Board EDGE RATE Rugged HS, 20 x 2Rows 5.0mm Lead Style, 0.8mm pitch, SMD Receptacle Make: SAMTEC ERM8-020-05.0-L-DV-K-TR 12

116 10 Pin Header Connector- receptacle 0.050 (1.27mm) Pitch Surface mount gold Make: Samtec Inc SFML-105-02-L-D-K-TR 10

117 10 Pin Header Connector, 2rows*5 PIN Shrouded Through Hole Make: SparkFun Electronics PRT-08506 10

118 CON16AP, WR PHD 1.27mm DUAL SMT PIN Header Surface Mount 16 positions Make: Wurth Electronik 62131621021 10

119 CON3 CONN HEADER Through Hole,Right Angle 3 position, 2.54MM09 Make: Samtec Inc. IPL1-103-01-F-S-RA-K 10

120 LED ,GREEN CLEAR, 0603 SMD, Discrete 2V Make:Wurth Electronik 150060VS75000 12

121 MARL R/A BICOLOR LED 151 Series Make: MARL 151-535-04 10

122 Bi Color LED 8mm PNL MNT RED/GREEN 2vdc IP67 ,20mA Make: APEM Inc Q8R5GYYRG02E 2

123 LED GREEN,CLEAR, 0603 SMD ,Discrete 2V Make: Wurth Electronik 150060VS75000 10

124 TVS DIODE BI-DIR Surface Mount, D0-214AB, 85V Clamp, 53VWM Make: Bourns Inc 1.5SMC62A 10

125 SCHOTTKY Diode 20V 3A SMA Make: Diode Instruments B320A-13-F 30

126 DIODE SCHOTTKY ,30V 100MA SOD-323 Make: Central Semiconductor Corp CMDSH-3 TR PBFREE 15

127 TVS DIODE,162V clamp ,3.7A lPP ,100VWM ,DO-214AA Make: Taiwan Semiconductor corporation SMBJ100A 10

128 DIODE GEN PURP ,50V , 1A surface mount DO-214AC Make: Onsemi ES1A 20

129 DIODE SCHOTTKY 60V,1A,Surface Mount SMA Make: Onsemi SS16T3 10

130 TVS DIODE ,9.2V clamp,5VWM,65.2A IPP ,Surface Mount, DO-214AA Make: Taiwan Semiconductor Corporation SMBJ5V0A 10

131 Fixed IND,68uH unshielded drum core,230MA, 6.7ohm, wirewound inductor, 0805 SMD Make: Murata Electronics LQH2MPN680MGRF 15

132 Ferrite Bead, 60ohms @100MHz,1 Power Line,6A,9m ohm,1806 ILN Make: Murata Electronics BLM41PG600SN1L 20

133 10ohms@100MHz 1 Ferrite bead,1A,25m ohm,0402 Make: Murata Electronics BLM15AG100SN1D 20

134 Fixed Shielded multilayer inductor,1.8uH,50mA,850m ohm SMD 0603 Make: TDK Corporation MLF1608A1R8KTD25 50

135 1 single line Ferrite Bead,5ohms@100mHz,700mA,70m ohm,0805 Make: Wurth Electronik 742792005 50

136 Fixed Ind 600nH shielded molded inductor,17.7A,4.52M ohm Make: Colicraft XAL5030-601MEC 15

137 Fixed Ind,1.2uH shielded drum core,wirewound inductor 11a,9.7m ohm Make: Bourns Inc SRP5030CA-1R2M 15

138 Power Inductors, 4.7uH,±20%, 54mohm, 4.8A SMD Make: SMIDA America Components Inc 0624CDMCCDS-4R7MC 15

139 32-bit ARM Cortex-M4/M0+ microcontroller with 256KB Flash Memory PACKAGE Make: NXP LPC54101J256BD64QL 5

140 32-bit ARM Cortex-M4/M0+ microcontroller with 512KB Flash Memory Make: NXP LPC54101J512BD64QL 6

141 Local Temperature Sensors with ±0.5°C accuracy from -40°C to +105°C,8 TDFN-EP* Make: Maxim Integrated MAX31725MTA+ 8

142 Dual, Current Feedback,8-Lead Plastic SOIC Low Power Op Amp Make: Analog Devices AD812ARZ 10

143 Integrated Triple Video Filter with Selectable Cutoff Frequencies for RGB, HD/SD ,20-Lead QSOP Make: Analog Devices ADA4412-3ARQZ 15

144 ADV7403-LQFP100 -12-Bit, Integrated, Multiformat SDTV/HDTV Video Decoder and RGB Graphics Digitizer Make: Analog Devices ADV7403 7

145 ADV7393-LFCP40 -Low Power, 10-Bit SD/HD Video Encoder Make: Analog Devices ADV7393 10

146 AD8062-MSOP8 - 300 MHz Rail-to-Rail Amplifiers Make: Analog Devices AD8062ARMZ 12

147 24BIT VIDE Encoder VID 69 -All-Format Oversampled Component Video/PC Graphics D/A System With Three 11-Bit DACs Make: Texas Instruments THS8200IPFPEP 10

148 AD8244BRMZ -Precision FET Input Quad Buffer,10-Lead MSOP Make: Analog Devices AD8244BRMZ 10

149 ADA4411-3ARQZ- Integrated Triple Video Filter and Buffer with Selectable Cutoff Frequencies and Multiplexed Inputs for RGB, HD/SD,24-Lead QSOP Make: Analog Devices ADA4411-3ARQZ 12

150 AD8146-LFCP24- Triple Differential Driver for Wideband Video Make: Analog Devices AD8146 12

151 SN74HC365PWR-Hex Buffers and Line Drivers with 3-state output,TSSOP Make: Texas Instruments SN74HC365PWR 10

152 DS1818R-5+T&R -3.3V EconoReset with Push Buttons,SOT23 Make: Maxim Integrated DS1818R-5+T&R 10

153 SP336EEY-L - 3.3V / 5V PROGRAMMABLE RS-232/485/422 SERIAL TRANSCEIVER,28-pin TSSOP Make: Exar Corporation SP336EEY-L 12

154 MAX14591ETA+T -High-Speed, Open-Drain Capable Logic-Level Translator,8 TDFN Make: Maxim Integrated MAX14591ETA+T 10

155 AD725-SOIC16 -RGB to NTSC/PAL Encoder with Luma Trap Port Make: Analog Devices AD725ARZ 10

156 PI6CV2304-SOIC8- IC CLK Buffer,1:4,140MHz 8-SOIC Make: Diodes INC/Pericom PI6CV2304WE 10

157 EL4581-SOIC8 -IC Video Sync Seperater Make: Renesas EL4581CSZ 10

158 1024K I2C Serial EEPROM_SOP_SOIC Make: Microchip 24AA1026-SN 10

159 THS7316D -3-Channel HDTV Video Amplifier With 5th-Order Filters and 6-dB Gain 8-SOIC Make: Texas Instruments THS7316DR 15

160 BNX022-01 - Block Type EMIFIL LC Combined Type Make: Murata BNX022-01 10

161 LM5050MK-2 -High Side OR-ing FET Controller Make: Texas Instxruments LM5050MK-2 10

162 AD812ARZ_SOIC-Dual, Current Feedback Low Power Op Amp Make: Analog Devices AD812ARZ 10

163 SN74LVC3G04DCT_A -Triple Inverter Gate Make: Texas Instruments SN74LVC3G04DCT 10

164 FET7A_PQFN -Dual, Current Feedback Low Power Op Amp Make: Fairchild FDMS86250 10

165 CDSOD323-T36SC -TVS Diode Series Make: Bourns CDSOD323-T36SC 12

166 IP_ProtectionIC_ADM1270ARQZ -High Voltage Input Protection Device Make: Analog Devices ADM1270ARQZ-R7 10

167 LTC3636EUFD -Dual Channel 6A, 20V Monolithic Synchronous Step-Down Regulator Make: Analog Devices LTC3636EUFD 10

168 SEMI LT3479 DC Switching Inverter -3A, Full Featured DC/DC Converter with Soft-Start and Inrush Current Protection Make: Linear Technology LT3479EFE#PBF 14

169 OSC_28.63636MHz, ±50PPM,-40 to 105Deg Make: ECS Inc ECS-286.3-20-3X-EP-TR 10

170 OSC_32.768KHZ CRYSTAL Make: Micro CrystalSwitzerland CC7V-T1A32.768KHZ+-20PPM_TBQA 10

171 OSC_17_734MHZ, 07050 size Make: Aandhra Electronics CXO7050LM3N017M7340000 15

172 ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 and STLINK/V2-ISOL features with digital isolation Make: ST Micro Electronics ST-LINK/V2-ISOL 2

173 N-Ch MOSFET,20V,1.3A,SOT23-3 Make: Onsemi NDS331N 10

174 Feed through capacitor,1.5uF,25V,1806 Make: Murata Electronics NFM41PC155B1E3 30

175 Banana jack connector, 5.5mm Make: KEYSTONE Electronics KEYSTONE 575-4 2

176 N-Ch MOSFET,60V,TO263-3 Make: Infineon Technologies SPB80P06PG 20

177 NPN BJT,40V,0.2a,SOT23-3 Make: Onsemi MMBT3904LT1G 20

178 USB-ML universal Programmer for ARM 8/16/32 bit devices Viz LPC 5400series Make: NXP/PE micro devices U-Mulitilink /USB-ML-Universal 1

Offer your compliance over following: Vendor Compliance/Remarks

1) The subject items are intended for Defence usage. Vendor to confirm whether any specific exemption is available for the taxes for Defence application.

2) HAL reserves the right to reduce / increase the quantity indicated above for ordering. Mention comments in "OTHER INFORMATION" below if any.

IMPORTANT NOTE: (a) The offered prices above should be quoted as per compliance provided to Annexure-1, 2 & 3 wihtout any deviation. (b) Conditional offers are not accepted

Any other Information: