Kalidas Marg sthit Awas No.-5 me H-1 Hall ke bahar path-way par tiles lagane ka karya, awas ke mukhya bhawan me khidki/darwazon, pallon par polish, VVIP lawn me shatigrast khidki badalkar UPVC me badalne, kamre ki shatigrast wooden flooring badalne,

Providing and laying in Position Cement Concrete of Specified Grade excluding the cost of Centering and shuttering all work up to plinth level 1:5:10 (1 cement, 5 Coarse sand (Zone-lll) 10 graded Stone 40 mm nomical size Derived from natural Sources ) DSR N0-4.1.10,

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours & shade, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse Sand), Jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of size size of tile 1200x1200 (DSR-11.41A.2.5),

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) DSR No-13.116

Fixed window / ventilator without mullion / Transom_ Using R3 series with frame (55 mm & above) x (45 mm & above). (Height upto 2.5 metre) DSR No 9.147.C1.3

Three Tack Three Panels Sliding window with two glazed & One wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R23 series with frame (98mm & above) x(40mm & above)& both glazed and fly screen sadh (30mm & above) X (55mm & above) with zinc aloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m) DSR No. 9.147.A4.2,

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class deodar wood. DSR No. 11.33.2,

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/aqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a derection perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every juction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compoung, jointing tapes, finishing with jointing compound in 3 layers covers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board, DSR No. 12.45.3,

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen plateform, vanity counter, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 Cement: 4coarse Sand) Joints treated with white cement mixed with matching pigment epoxy touch ups, including rubbring, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any Colour and shade Area of slab over 0.50 sqm. DSR No. 8.2.2.2 ,

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes. DSR No. 18.8.2

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen Sink as per IS : 13983 with C.l. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 225 mm. DSR No. 17.10.1.2,