CONSTRUCTION OF ELECTRIC CREMATORIUM (GAS FIRED) AT ADITYAPUR, CHAIBASA, SARAIKELA AND JUGSALAI UNDER KOLHAN DIVISION, JHARKHAND

Amount

BORING

Basic rates for 125/ 115 mm dia drilled tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig machine all complete including supply all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.

(a) From 0.00 M to 30.00 M below G.L

(b) From 31.00 M to 60.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm dia nominal size

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 100 mm Dia.

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 100 mm clamp

Supplying 100mm dia. Submersible pump sets confirming to IS 8034 and motor cvonfirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft ant polypropylene/ norylimpeller. Motor suitable for working on 415 V+10%, 3PH, 50 HZ, AC supply with cable guard, thurst carbon/ fibre bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined no return valve shall be provided with pump. 3 m submersible copper conductor cable in single/ double run and nylon rope as required length shall be provided with each pump. Submersible pump set 100mm dia (with polypropylene/ Noryl Impeller) upto 20 stages. 2HP.

Supplying and fitting of standared make starter pannel board with arrangement of all necessory protection ,including all taxes , royalty etc all complete job as per direction of E/I

Supplying ,fitting & fixing & connecting 3 core 4 sqmm flat copper submerssible cable of Finolex / Hevels make including all taxes ,royalty etc all complete job as per direction of E/I

Supplying and laying /lowering of GI pipe of 50 mm dia including of required fittings solvent etc complete job as per direction of E/I

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Providing coarse clean local SAND IN FILLING in foundation trenches or in plinth including ramming and watering in layer not exceeding 150 mm thick with all leads and 1.5 M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer In charge (Mode of measurement compacted volume)

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing and laying 6 mm precast SEMI GLAZED CERAMIC TILES of approved quality in DADO over 12mm cement mortar (1:3) and jointed with white cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specification and direction of E/I with grade A coloured 15cmx15cm tiles.

Providing 50mm thick cement concrete flooring ( 1:2:4 ) with 20mm to 6mm size graded stone chips finished with floating coat of neat cement in panels, including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm cement plaster(1:3) with clean course sand of F.M 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curing taxes and royalty all complete as per building specification and direction of E/I.

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50 cm deep and1.8 cm thick fixed in Urinal Partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1cement :2 coarse sand : 4 stone chips)as per direction of E/I and finished smooth.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

suppling , fitting and fixing good quality well dressed and well seasoned sal wood work in chaukhat in doors window ,sky light, fanlight and celevitial window opening including wedge over clmps all including application of two coats of wood preservative of approved quality on the surface , building walls and lintel all complete as per building specification and direction of El.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (Approved Brand - Green club/ Green Optima/ Century/ Duro).

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-incharge (Frame work shall be paid for separately).

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i. e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium window, ventilator shutters etc. with EPDM / Neoprene gasket etc complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness

Providing and fixing glazing in aluminium door, shutters etc. with PVC/neoprene gasket etc complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.0 mm thickness

Providing and fixing Double action hydraulic floor spring of approved brand and manufacture I.S.:6315 marked, Hardwyn Make (Model 3000) or equivalent for doors including cost of cutting floors as required, embedding in floors & cover plates with brass pivot and single piece M.S. sheet outer box with side plate etc.complete as per the direction of E/I. WITH STAINLESS STEEL COVER PLATE MINIMUM 1.25MM THICKNESS:-

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

Providing P.C.C. (1:3:6) in foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 20mm nominal size)

Extra for providing and mixing waterproofing material in cement conncrete work in doses by weight of cement as per manufacturer's specification.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing, hosting and fixing above plinth level up to floor level precast Reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand ), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , exculuding the cost of reinforcement, with 1:1.5:3 (1cement : 1.5 coarse sand (zone-iii) : 3 graded stone aggregate 20mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for : Chajja

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Supplying, fitting & fixing 250 x 20 x 6 mm L-type M.S. clamp properly fishtailed including making holes and setting the same in 375 x 125 x 75 mm cement concrete block (1:2:4) with cost of all layout and materials and taxes as per building specification and direction of E/I.

Supplying, fitting & fixing M.S. GRILL made of 20 x 6 mm flat as per approved design and drawing properly fabricated with joints continuous fitted, welded and finished smooth, hoisting as per building specification and direction of E/I.

Providing & fixing FAN HOOK of 16 mm dia M.S. bar, 1 M long bent to required size and shape, placed in position and fluid in the R.C.C. slab-beam at the time of casting all complete as per building specification and direction of E/I.

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge. (Approved brand - Godrej/ Dorset)

Providing and fixing aluminium round shape handle of outer dia.100 mm with SS screws etc. coplete as per direction of E/I. Powder coated minimum thickness 50 micron aluminium.

Providing and fixing aluminium hanging floor door stoppers ISI marked anodized (anodic coating not less than grade Ac 10 as per I.S. 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper

Providing and fixing aluminium TOWER BOLTS ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required color or shade with necessary screws etc. complete. 300X 10MM

Extra for providing lipping with 2nd class teak wood battens 25mm minimum depth on all edges of shutters (over all area of door shutter to be measured).

Providing and fixing sliding arrangement in racks/ cupboards/cabinets/ Window shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately)

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roof terraces etc. consisting of following operations. Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water proofing compound conforming to IS : 2645 over the RCC slab including cleaning the surface before treatment. Laying cement concrete using broken bricks/brick bats 25 mm to 100 mm size with 50% of cement mortar of mix 1:5 ( 1 cement : 5 coarse sand ) admixed with proprietary water proofing compund conforming to IS :2645 over 20 mm thick layer of cement mortar 1:5 (1 cement : 5 coarse sand ) admixed with proprietary water proofing compund conforming to IS :2645 to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. Laying cement concrete using broken bricks/brick bats 25 mm to 100 mm size with 50% of cement mortar of mix 1:5 ( 1 cement : 5 coarse sand ) admixed with proprietary water proofing compund conforming to IS :2645 over 20 mm thick layer of cement mortar 1:5 (1 cement : 5 coarse sand ) admixed with proprietary water proofing compund conforming to IS :2645 to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. After two days of proper curing applying a second coat of cement slurry admixed with proprietary water proofing compound conforming to IS: 2645. Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 ( 1 cement : 4 coarse sand ) admixed with proprietary water proofing compund conforming to IS : 2645 and finally finishing the surface with trowel with neat cement slurry and making of 300X300 mm square.The whole terrace so finished shall be flooded with water for minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the E/I. With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (WORKS TO BE DONE BY REGISTERED APPLICATOR OF PIDILITE/ SIKA/ ROFF WITH 10 YRS. GUARANTEE.)

Providing designation 75 A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75 A BRICK WORK in CM. (1:6) in SUPERSTRUCTURE with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening,racking out joints to 15 mm depth,curing, taxes and royalty all complete as per building specification and direction of Engineer Incharge

Providing 125 mm thick REINFORCED DESIGNATION 75 A BRICK WORK in C.M. (1:4) in SUPERSTRUCTURE with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, cost of materials, racking out joints to 15 mm depth, carriage, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of Engineer Incharge .

Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonary

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. 600 x 600 mm size

Providing and fixinging 20 mm thick mirror polished, machine cut for kitchen platform and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 (1cement :4 coarse sand) laid and jointed with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shade

Extra for providing edge moulding to Granite stone counters, vanities etc. over above including machine polishing to edge to give high gloss finish etc. complete as per design approved by Architects / E/I.

DT: Basic rates for 125/115 mm dia Drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH ring Machine all complete including supplying all meterial, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of engineer-in-charge. (i) Drilling up to 30 mtr. Depth below G.L. in Rural Area

Supplying, assembling, lowering and fixing in vertical position in borewell unplasticized PVC medium well screen (RMS) pipes with ribs, confirming to IS: 12818, including hire and labour charges, fittings and accessories etc. all complete, for all depths, as per direction of engineer-in-charge. 100 mm nominal size dia. -

Supplying,filling, spreading and levelling stone boulders of of size range 5cm to 20 cm, in recharge pit, in the required thickness, for all leads and lifts, all complete as per direction of Engineer-in-charge.

Supplying,filling, spreading and levelling gravels of size range, 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in the required thickness, for all leads and lifts, all complete as per direction of E/I.

Constructing brick masonary chamber for Underground C. I. Inspection Chamber and bend with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. Cover with frame (light duty) 455X610 mm internal dimensions, total weight of cover with frame to be not less than 38 KG. (weight of cover 23 kg. and weight of frame 15 kg) RCC top slab with 1:1.5:3 mix (1 cement:1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 mix (1 cement:5 coarse sand :10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm th. with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455X610X mm and 45 mm deep for single pipe line with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete.

150 MM dia R.C.C. pipe

250 MM dia R.C.C. pipe

Supplying fitting and fixing Galvanised wire mesh of average width of aperture 1.4 mm and nominal dia of wire 0.63 mm (2'-0"x2'-0"*2) in position as per specification and direction of E/I.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing tuck pointing (1:3) in cement on brick work with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.

Making 20x6 mm grooves in plaster surface over walls trully horizontal or vertical as specified at regular intervals at all heights including cleaning finishing , scaffolding and curing with all leads and lifts of water all complete as per buildinng specification and direction of E/I.

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works use of chequered plate wherever required, all complete

Providing 2 coats of SYNTHETIC ENAMEL PAINT of approved shade and make over STEEL SURFACE grills & railings including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth copmlete .

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I

Finishing walls with Premium Acrylic Smooth exterior paint with silicone additives "Snowcryl - XT" of M/S Snowcem India Ltd, or equivalent of required shade. New work (Two or more coats applied @1.43 ltr / 10sqm. Over and including base coat of water proofing cement paint Snowcem Plus or equivalent applied @ 2.20 kg./10 sq.m. )

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall suface to prepare the surface even amd smooth complete.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm.

Providing two coats of SYNTHETIC ENAMEL PAINT of approved shade and make over new WOODEN surface including cleaning the surface after removing dirt, scales, grease and sand papering, including cost of scaffolding etc. all complete as per building specification dirction of E/I.

Providing Primer one coat of read lead paint of approved make over new STEEL SURFACE preparing the surface after cleaning, removing rust, dirt, scales, smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing 2 coats of SYNTHETIC ENAMEL PAINT of approved shade and make over STEEL SURFACE grills & railings including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I.

Supplying and fixing Rolling Shutter of approved make, made of required size M. s. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire od adequate strength confirming to IS : 4454-part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover.

Providing and fixing ball bearing for Rolling Shutters

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 16.80 sqm in area

Providing & fixing on wall face unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia. 110mm diameter

Providing & fixing on wall face unplasticised -P.V.C. moulde fittings / accessories for unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion .

Coupler - 110 mm

SHOE - 110MM

BEND - 110 MM

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 MM.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (Approved Brand - Tata Bluescope/ Equivalent)

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

Flashings/ Aprons.( Upto 600 mm)

Gutter (600 mm over all girth)

Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.

Steel work welded in built up sections as per drawing including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using steel in Spiral stairs. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing septic tank for 50 users masonary septic tank of size (12'-0'x3'-6"x6'-0")effective size and I.C. of requried size with 250 mm thick brick wall in cement mortar (1:4) including base of 4" thick PCC (1:2:4) over brick soling and sand filling with two coats of CICO plaster(1:6) with punning complete with all earth work excavation back filling as per details drawing & carriage of materials, complete job.

Making Soak Pit 2.5 m diameter 3.0 meter deep with 45x45cm dry briick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standerd design .With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing & ejecting Chemical emulsion for pre-constructional ANTI TERMITE TREATMENT and creating a chemical barrier under a alround the column pits, wall trenches, basement excavation, top surface of plinth filling junction of wall and floor along the external perimeter of building expansion joints, surrounding of pipes and conducts tic. complete (plinth area of the building at ground floor only shall be measured) with Chlorpyrifos 20% EC as per building specification and direction of E/I. (4 stages treatment)

CARRAIGE OF MATERIALS

LOCAL SAND ( 5KM )

COURSE SAND ( 25KM )

CHIPS ( 22KM )

BRICKS ( 7KM )

SANITARY, WATER SUPPLY & DRAINAGE WORKS

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast iron P or S trap, 10 litre low level white P.V.C. Flushing cistern with munally controlled device (handle lever) conforming to IS:7231 Parryware/ Hindware with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. White Vitreous China Orissa pattern W C pan of size 580 X 440 mm with integral type foot rest.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled devicde (handle lever), conforming to IS:7231, parryware/Hindware/with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15mm nominal bore

Providing and fixing C.P Soap Dish of aaproved size, shape and approved brand with concealed fittings, complete job.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china flat back half stall urinal of 580X380X350mm with white PVC automatic flushing cistern, parryware/Hindware with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass with waste fitting as per IS : 2566 P.V.C. trap with outlet grating and other couplings in C.P. brass including parenting of fitting and cutting and making good the walls and floors wherever required. Single half stall urinals with 5 litre P.V.C. auotmatic flushing cistern.

Deduct the 5 litre P.V.C. auotmatic flushing cistern fron urinal (Sl. No. - 7359. rate = Rs. 450+15% = 517.50)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end ) 32MM nominal bore.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 25mm nominal bore.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 100mm dia. Steel Jali of approved quality.

Providing and fixing stainless steel A ISI 304(18/8) kitchen sink as per I.S.13983 with C.I. Brackets stainless steel plug 40mm including painting of fittings and brackets cutting and making goods the walls wherever required: kitchen sink without drain board, 610x510mm bowel depth 200mm

Providing and fixing C.P Sink cock with swinging casted spout with concealed fitting arrangements.

Providing and fixing unplasticised P.V.C. connection pipe with c.p. nuts collar and bush of approved quality. 15 mm nominal bore with 45 cm length.

Providing And fixing 32 mm waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible Pipe

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (ITEM FOR RAIN WATER, SOIL, WASTE & VENT PIPES) 100 mm dia

Coupler -110 MM

Single pushfit Coupler - 110 MM

Single tee with door - 110X110X110 MM

Single tee without door - 110X110X110 MM

Bend 87.5° - 110 MM

SHOE - 110 MM

Nahani Trap - 110X75 MM

Multitrap - 110X100 MM

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I.(Approved Brand - ASTRAL/ SUPREME) Concealed work including cutting chases and making good the wall etc..

15 mm nominal dia Pipes

20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement & testing of joints complete as per direction of E/I. (Approved Brand - ASTRAL) Exposed on Wall

25 mm nominal dia Pipes

32 mm nominal dia Pipes

Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete.

150 MM dia R.C.C. pipe

250 MM dia R.C.C. pipe

Constructing brick masonary chamber for Underground C. I. Inspection Chamber and bend with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. Cover with frame (light duty) 455X610 mm internal dimensions, total weight of cover with frame to be not less than 38 KG. (weight of cover 23 kg. and weight of frame 15 kg) RCC top slab with 1:1.5:3 mix (1 cement:1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 mix (1 cement:5 coarse sand :10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm th. with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455X610X mm and 45 mm deep for single pipe. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass Health Faucet with 8mm dia. 1.20m long flexible tube & wall hook. Hand Shower - CAT. NO. - JAQUAR, ALD - 573

Providing and fixing C.P. Towel Ring (round) with flange. Towel Ring - CAT. NO. - JAQUAR, AQN - 7721

ELECTRICAL

Wiring for light point/fan point/exhaust fan/call bell point with 1.5 sqmm PVC insulated copper conductor cable in surface / recessed PVC conduit with moduler type switch,moduler plate,suitable size GI box etc. as required .

Wiring for light/ power plug plug with 2 X 4 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.(for AC &16A socket)

Wiring for light/ power plug plug with 4 X 4 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 2 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for submain wiring with the following size of PVC insulated, copper conductor single core cable in surface / recessed PVC conduit as required:

2x1.5 sq.mm.+1x 1.5 sq mm(for toilet switch board +6A socket)

2x2.5 sq.mm.+1x 2.5 sq mm(for switch board )

4 x 6 sq mm +2x6 sq.mm. (Sub-Mains Light DB's)

4 x 10 +2x10 sq.mm. (Sub-MainsPower DB's)

Supplying and drawing following sizes of PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit / PVC casing capping / as required. 2x1.5 sq mm

S/F of following sizes of PVC conduit alongwith the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required . 25 mm PVC coduit.

Supplying and fixing following moduler switch / socket on the existing moduler plate & switch box including connection but excluding moduler plate etc. as reqd.

5/6 amps switch

5/6 amps socket outlet

Supplying and fixing stepped type electronic fan regulator on the existing modular plate & switch box including connection but exluding modular plateetc.as required..

Supplying and fixing moduler type blanking plate.

Supplying and fixing suitable size GI box with moduler plate cover in the front on surface or in recess including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps. moduler type switch, connections painting etc. as required. (For light plugs).

Supplying and fixing suitable size GI box with moduler plate cover in the front on surface or in recess including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps. moduler type switch, connections painting etc. as required. (For power plugs).

Supplying and fixing of following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts,on surface /recess, complete with tinned copper bushbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, including painting, earthing etc. as required.

4 way(4+12)double door Horizontal type

6 way (4+18)double door Horizontal type

Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' catagory, miniature circuit breaker (10 KA) of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

6/32 amps, Single pole

32 amps.TPN

40 amps.TPN

Supplying and fixing 20 amps, 240 volts, SPN, industrial type socket outlet, with two poles and earth metal enclosed plug top along with 20 amps. "G" series, SP MCB (10 KA) in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet, and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, TP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade.of following size on wall surface as required. upto 35sq.mm.(clamped with 1 mm thick saddle)

Supply of PVC/ XLPE Insulated PVC sheathed heavy duty armoured electric cable with alluminium conductor for working voltage upto and including 1100 volts (conforms to IS:1554,part-1)

10 sq mm x 4 core

25 sq mm x 3.5 core

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

4 X 10 sq. mm (25mm)

3½ X 25 sq. mm (28mm)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness

LT PANEL (NORMAL SUPPLY) : -INCOMING (1- sets) each with following: 100 Amp, MCCB FP -1 no, Ammeter, ASS, CTs, Voltmeter, VSS, Fuses, 1 Sets of Phase Indicating Lights with fuses & following accessories: - BUS BARS,

OUTGOING: - b)2 Nos of 40 Amp TPN MCB, b)4 Nos of 32 Amp TPN MCB, b)4 Nos of 16 Amp TPN MCB, c)4 Nos of 16 Amp SPN MCB, LT Panel (Normal) as above ( G.F)

25-100 amps, 16 KA, fixed thermal setting

40 amps.TPN

6/32 AmpTPN MCB

16 amps.SPN

LED INDICATOR LAMP R/Y/B/G

DIGITAL VOLT METER 500V(3phase class 0.5)

DIGITAL A METER 500V(3phase class 0.5)

CT coil of CT tatio100/5 IS 2705 part 3

25MM*5MM(1.15 Kg/Mtr)copper strip

16 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

10sq mm ISI marked FRLS PVC insulated single core copper conductor cable

6 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

1.5 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

S/F wall floor mounted cubical panel board , fabricated with 16 gauge iron sheet suitable for panel mounted switch disconnector ,incliding busbar chamber,insulator and painting etc.as required .(but without busbar copper strip)

S/F of Earthing electrode 80mm dia x 3mtr with backfill compound chemical 4 bag (per bag 25Kg)including earth cutting removing and installation charge.

Supplying and laying 25 mm X 5 mm GI strip at 0.50 metre below ground as strip earth electrode, including connection/ termination with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping with 2 sets of brass nut bolt and & spring washer spaced at 50 mm)

P/F of lighting conductor finial, made of 25mm. Dia. 300mm. Long GI tube, having single prong at top, with 85mm. Dia. 3mm. Thick copper base plate including holes etc. complete as required.

Rivetting, sweating and soldering of copper/GI tape (with another copper/GI tape base of the finial or any other metallic object) as required.

Providing and fixing GI tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as reqd.(for horizontal run)

Providing and fixing GI tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as reqd.(for vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of tinned G.I. bolts, nuts, chuk nuts and spring washers etc. complete as required.

S.I.T.C of following rating surfface mounted LED tube light fitting suitabe for 230v 50Hz single phase supply etc complete as required

20/22w LED tube light

S.I.T.C of following rating recess/ surfface mounted LED round /square shape down light luminaierewith pressure die cast housing for single phase supply voltage luminarie shall be confirm to IS:10322 part-5/section 2 or IEC :62722 with all necessary accessories as required.

10/12w LED round down light.

18/20w LED round down light.

S.I.T.C of following rating LEDstreet light luminaiere with pressure die cast housing and toughend glass cover (IP 66 protection )in xisting pole/pipe for supply voltage 100-270 AC 50 Hz luminarie shall be confirm to IS:10322 part-5/section 3and shall be complete with all necessary accessories as required.

90/100W LED street light.

S.I.T.C of following rating LED Flood light luminaiere with pressure die cast housing and toughend glass cover (IP 66 protection )in xisting pole/pipe for supply voltage 100-270 AC 50 Hz luminarie shall be confirm to IS:10322 part-5/section 3and shall be complete with all necessary accessories as required.

120W LED Flood light.

S.I.T.C of following size ceiling fan 3 blades confirming to IS-374:2019including wiring the down rods of standared length (upto 30 cm)with 1.5 sq mm FR PVC insulated copper wire suitable for 230v 50Hz single phase supply etc.as required.

1400mm (56")Ceiling fan

9" (230) mm )metal exaust fan

12" (300) mm )metal exaust fan

15" (380) mm )metal exaust fan

S.I.T.C of following rating LED Post top lamp made in die cast aluminium housing with decorative clear /opal acralic diffuser on existing pipe including connection with 1.5 sq.mm copper conductor etc all complete as required.

40/45W LED post top lamp opel/clear (gate light)

S/F of 100w suspended type industrial COB LED highbay light with aluminium die cast heat sink.

Providing of bulkhead fitting with 9/10w LED bulb.

S/F 2 pin 5A ceiling rose on the existing junction box wooden block including connection etc ,as required.

Erection of wall bracket / ceiling fittings of all sizes and shapes ontaining upto two GLS lamp per fitting complete with all accessories including connection etc as required.

Installation, testing and commissioning of prewired, fluorescent fittings,compact fluorescent fitting of all types , complete with all accessories and tubes etc. directly on ceiling / wall, including connections with 1.5 sq.mm. PVC insulated, copper conductor, single core cable etc as required

Installation, testing and commissioning of ceiling fan including wiring the down rod of standard length (upto 30 cm.) with 1.5 sq.mm. PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation of exhaust fan upto 450 mm. sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing, commissioning etc. as required.

Silent type DG set of capacity 30KVA three phase with AMF panel IS/IEC-60034-1. IS:1460 IS: 13018

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from local or other approved source including royalty and cariage up to 1 km. (Manure measured in stacks will be reduced 8% for payment).Screened through sieve of I.S. designation 4.75 mm.

Rough dressing the trenched ground including breaking clods.

Fine dressing the ground

Spreading of sludge, dump manureor / and good earth in required thivkness(Cost of sludge, dump manure or / and earth to be paid seperately).

Mixing earth and sludge or manure in proportion specified or directed.

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Callistemon lanceolatus of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus bengalensis (varigated) of height 75-90 cm., multibranched in earthen pots of size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.

Dreaceana pendanus, well developed, having 6 to 8 suckers with helthy foliage in 25 cm size Earthen pot /Plastic pot

Dianella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot / Plastic Pot.

Euphorbia milli hybrid variety, having ht. 30 cm to 45 cm with multi branch, full bloom, fresh and healthy leaves in 30 cm size of Earthen Pot / Plastic Pot.

Adenium Obesum well developed with fresh & healthy 4 to 5 branch 60 to 75 cm ht. plant in 40 cm size Earthen Pot/ Plastic Pot

Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot / Plastic Pot.

Dracaena Mahatma having ht. 30 cm to 45 cm, well developed, fresh and healthy foliage in 20 cm size of Earthen pot / Plastic pot.

Providing and stacking of Butea frondosa (Flame of Forest) of height 60-75 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Foxtail Blue palm/ Fan palm of ht. 180-210 cm bottom girth 2530 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes joining of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of E/I. (Approved Brand - ASTRAL) Exposed on Wall - 25 MM DIA.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end ) 25MM nominal bore

SUPPLY AND INSTALLATION OF CO2 TYPE FIRE EXTIGUISHER 4.50 KG @ 6,800.00 EACH + 10% C.P. (AS/ GEMS RATE)

SUUPLYING, INSTALLATION, TESTING & COMMISSIONING OF CREMATION PLANT (GAS FIRED AUTOMATIC BURNER) WITH ALL FURNACE WORK, MACHINE & CHIMNEY, INCLUDINGHIGH ALUMINA BRICK LINING AND ALL COMPLETE

LPG/ PNG GAS CYLINDER (- ----KG) : 18 Nos. @ ₹ 3,000.00 Each + PIPELING, MANIFOLD & PRESSURE GAUGE (₹2,50,000.00)

SOLAR LIGHT WITH M.S. POLE -

M/S GUPTA CONSTRUCTION