SPECIAL REPAIRS TO BLDG No. 10 ABOS OF RMS BELGAUM AND SPECIAL REPAIRS TO BLDG No. 7 BSO OFFICE UNDER GE BELGAUM

Amount

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thick, below or above GL all as specified and directed.

Demolition of plain cement concrete of any description and in any position, not otherwise specifically provided for all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar or lime cement mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles, in any position below or above ground level all as specified and directed.

Dismantling timber scantlings 40 sq.cm and over in section, in any position, in un-framed work all as specified and directed.

Dismantling timber scantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section all as specified and directed.

Dismantling of battens for tiles, shingles etc, of any size spacing exceeding 15cm including tilting fillets in roofing all as specified and directed.

Dismantling boarding of any description fixed in any position with nails all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area n exc 1.5 Sqm each all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Taking down shutters of any description area exc 1 sqm and n.exc 2 sqm each all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position all as specified and directed.

Dismantling of single layer Mangalore pattern or similar tiles in roofing all as specified and directed.

Dismantling of single layer Mangalore pattern or similar tiles in roofing bedded in lime or cement mortar all as specified and directed.

Dismantling of plain or corrugated steel sheets of any gauge and thickness, in roof coverings, valleys, gutters, etc. all as specififed and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., (measured overall as fixed along the centre line over fittings and accessories)

Dismantling wall or ceiling boards or insulation boards/ slabs of any thickness including cover fillets all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed.

Demolition of stone slab and tiles of any description and any thickness in floors laid, bedded and pointed in any mortar all as specified and directed.

Taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc., all as specified and directed.

Taking up or down existing unserviceable 15mm bore steel & connections tubes of any grade and making good disturbed surfaces all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in hard/ dense soil all as specified and directed.

Returning filling in with approved excavated soil including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc. and mass concrete including demolition of existing RCC work complete all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate in columns , pillars, piers, posts and struts including demolition of existing RCC work all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate in beams, cantilevers, lintels, lintel bands, chajjas etc including demolition of existing RCC work all as specified and directed.

M&L plain cement concrete 1:3:6, type C1, using 20mm graded stone aggregate as in coping, bed blocks, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L for plain cement concrete 1:3:6 type C2, using 40mm graded stone aggregate as in surface channels and drains concrete all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6, type C1, using 20 mm graded stone aggregate and setting in CM 1:6 all as specified and directed.

Supply only integral water proofing compound all as specified and as directed.

M&L for use of form work to sides of concrete foundations, column footings, plinth beams and similar works for rough finished flat concrete surfaces, vertical or to batter, all as specified and directed

M&L for use of form work to sides of pillars, posts, struts, columns, etc. for fair finished concrete surfaces, square, rectangular or polygonal all as specified and directed.

M&L for mild steel TMT bars 8mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

All as described in item No. 33 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

M&L for 2nd class hard wood in scantling, clean sawn fixed in unframed work all as specified and directed.

Fixing only serviceable timber scantling of any description obtained from dismantling in un-framed work all as specified and directed.

M&L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, wrought, secured with nails or beads; sectional area exc 13 and n.exc 25 sq.cm all as specified and directed.

Fixing only serviceable timber fillets, of any description obtained from dismantling, sectional area exc 13 and n.exc 25 sq.cm, secured with nails or beads; all as specified and directed.

M&L for aluminium frame work as in doors, partitions, windows and ventilators using powder coated aluminium sections including provision of glazing clips, hinges, handles, etc all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary gaskets. (iii) Particle board/ glass panels/ wire mesh shall be measured and paid separately.

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on both sides reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelaminated PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of prelaminated PVC sheets on both sides to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and directed

S&F extruded aluminium alloy handles, 150mm in size, fabricated type, anodised all as specified and directed.

S&F aluminium anodised barrel tower bolt 200mm size all as specified and directed.

S&F aluminium anodised barrel tower bolt 150mm size all as specified and directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F stainless steel butt hinges 100mm in size, medium weight all as specified and directed.

S&F in repairs Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 150mm complete fixed in floors all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F mild steel works in tubular trusses, rafters, purlins, etc. including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 all as specified and as directed.

S&F mild steel framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 all as specified and as directed.

M&L for mild steel flats as in wind ties for roof including securing bolts and necessary drilling, conforming to Fe-290 Gde E-165 all as specified and as directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 all as specified and as directed.

S&F rolled mild steel channel, angle, or tee sections as in columns, beams, Joist, etc. including cutting and welding as necessary for staging for water tanks and the like etc, conforming to Fe.410.Gde-E-250 all as specified and as directed.

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in ridges, valleys, hips, claddings, etc. fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for cement concrete roofing tiles, rustic red colour, 420 x 330mm size, 230 kg minimum breaking strength, double groove design, as in roofing, interlocking at side joints, laid dry all as specified and as directed. Make: ETERNA model of INDOGRACE or PIONNIER or equivalent approved make.

M&L for concrete ridge/ hip cap tiles to suit rustic red concrete roofing tiles, 330 x 207/249mm size, minimum 15mm thick, bedded and jointed in CM 1:6 all as specified and directed. Make: INDOGRACE or PIONNIER or equivalent approved make.

S&F in repairs 600mm dia wind operated air circulating roof ventilator, aluminium body, made of 0.5mm thick aluminium sheet, stainless steel shaft, double shielded self lubricating ball bearings, dia of turbine 760mm, dia of neck 610mm, height 460mm, 42 vanes, with profile suitable for fixing with Galvalume roof sheet including necessary fixing bolts etc, complete as specified and directed.

S&F suspended false ceiling system with 16mm thick mineral fibre acoustical MINA TUFF EDGE TILES (MIRO LOCK), white, fibre performance class-I (BS 456, Part 6&7), with bio coating on the exposed face of tiles, module size 600x600, laid on 15 mm thick SILHOUTTE EXPOSED GRID system, with minimum load carrying of 11.68 Kg/Sqm, white/black colour all as specified and as directed.

M&L for 3mm thick Aluminium Composite Panel comprising of a core containing not less than 70% non combustible mineral filling sandwiched between two skins of 0.5mm thick aluminium alloy PERALUMAN-100 (AlMg1-NS41) complete with all necessary sub-structures, anchors, hardware and fittings to provide a total installation, fixed to existing wooden/ steel members all as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc. Make: Alstrong/ Aludecor/ Alucobond/ Eurobond

S&F PVC (SWR) eaves gutter half rounded 150mm bore including pipe accessories PVC holder bats bolts nuts etc. all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded aggregate as in sub base/ levelling course for flooring all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded aggregate as in sub base for flooring finished even and fair all as specified and directed.

M&L for coloured vitrified tiles, square or rectangular, light shade, 10mm thick, area of each tile not exc 0.36 Sqm, as in floors/ skirtings, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured non skid ceramic tiles, 8 mm thick area of each tile exc 0.11 Sqm but not exc 0.18 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured glazed ceramic tiles 300mm x 450mm x 7 to 8mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for machine cut granite stone slab, premium quality, any colour, 18 to 19mm thick, set and jointed with neat cement slurry laid over and including 15mm thick screed bed in cement mortar 1:4 and pointed in white cement (1:2) mixed with colouring pigments to match with the shade of slab, as in platforms, steps, cills, etc. including rubbing and polishing complete all as specified and directed.

M&L for grinding and polishing the existing old Terrazzo/ Tandoor/ Kota stone flooring/ skirting including filling in open joints with cement slurry and pigment and treating the surface with bees wax complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C2, (Using 40 mm graded stone aggregate), 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for 5mm thick sheet glass ordinary quality and glazing in square exc 0.5 sqm in each pane all as specified and directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable) over a coat of primer over 3mm thick layer of wall care putty, on walls, pillasters, cornices, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of exterior emulsion paint over a coat of primer on surfaces of walls including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of exterior emulsion paint over a coat of primer on new platered surfaces of walls and necessary preparation of surfaces all as specified and as directed.

M&L for preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L for preparation of old painted wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for 500 litres capacity rotational moulded polyethylene (HDPE) water storage tanks, 'ISI' marked, cylindrical, vertical with closed top conforming to IS 12701-1989 having two layers wall construction with manhole lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes, hoisted and fixed in position including dismantling and taking down of existing PVC water storage tanks of any descriptionand capacity and testing complete all as specified and directed.

S&F in repairs 25mm bore gun metal gate valve heavy duty ISI marked with iron wheel head screwed both ends to iron pipes and fixed all as specified and as directed

S&F in repairs 25mm dia PTMT ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe all as specified and directed.

S&F 25mm bore UPVC pipes, pressure rating 10 kgf/ sqcm with and including provision of all fittings, fixed complete to walls/ roofs or laid in floors/ trenches including taking up or down existing unserviceable GI pipes of any description alongwith its connections all as specified and as directed.

S&F 15mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F in repairs 15 mm bore Bib tap, long body, brass chromium plated, fancy type with wall flange, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F in repairs 15 mm bore 2 way Bib tap, long body, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed. Make: Cat No. FUS 29041 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs, pillar taps, cast copper alloy chromium plated with capstan heads, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed.

S&F in repairs health faucet, brass chromium plated with 1m long flexible PVC tube and wall hook all as specified and as directed. Make: Cat No. ALD-CHR 563 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs cascade type vitreous china wash down water closet pan (pedestal pattern), white, coupled with flushing cistern including 'P' or 'S' trap, seat and cover, fixing bolts etc, connecting to drain pipe and flushing pipe all as specified and as directed.

S&F in repairs Vitreous China wash basin, any colour, oval type, size 630x450mm, including provision of vitreous china pedestal fancy type swan neck type pillar tap, waste coupling and waste pipe including cutting for and pinning in ends of brackets etc complete all as specified and directed. Make: Cat No-1022 CONCORD MODEL of CERA or equivalent in Parryware/ Neycer/ Hindware

S&F in repairs PVC connection 15mm size with PTMT nuts, 450mm long all as specified and directed.

S&F in repairs fancy type towel rod, brass CP, 600mm long, fixed to wall with plugs and chromium plated screws all as specified and as directed. Make: CAT No. CAN-CHR- 1111Nof JAQUAR or equivalent model in JOHNSON/ ESS ESS/ CERA

S&F in repairs 1mm thick stainless steel sink, overall size not less than 495x420mm, bowl size not less than 410x330x160mm, with plug, washers and wastes including bedding in cement mortar, fixing cantilever brackets and connecting union to pipe all as specified and as directed.

S&F 1mm thick stainless steel sink of overall size 2900mm long x 760mm wide consisting of 3 Nos. of bowl with each bowl of size 570mm x 530mm x 320mm, 1 No. draining board of size 600mm x 760mm and 150mm high splash board on rear and sides of sink including provision of stainless steel framed support manufactured with 6 Nos. of 18 gauge stainless steel tubular legs of size 40mm x 40mm, 1100 high and duly interconnected with 18 gauge stainless steel tubular stiffeners of size 30mm x 30mm including PTMT plugs, washers, waste couplings and waste fittings and connecting unions to pipe all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes, single socketed, in any length, with rubber ring joints, fixed to wall with required iron strap or clamp, as in rain water drain pipes all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall including demolition of breaking up drain pipes (AC or reinforced concrete) set in cement mortar, all as specified and directed.

S&F PVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

Taking down carefully point wiring of any description complete for light, fan, 5 A socket, 15 Amps socket, 2 way points and bell point etc including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, holders, etc. all as specified and directed.

M&L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC casing capping of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including 1/2 module GI terminal box flush mounted into wall with standard white modular cover plate & frames for mounting switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed.

All as described in item No. 102 but for one fan point controlled by one switch and regulator.

All as described in item No. 102 but for one call bell point controlled by one modular bell push

All as described in item No. 102 but for one 05 Amps socket outlet on independent board.

All as described in item No. 102 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 102 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Two runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

S&F modular switch piano type, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular switch, piano type, 1 way, 16 Amps 230 volts, AC, all as specified and directed.

S&F modular bell push, 1 module, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular socket outlet, 2 module, 6 Amps 2 cum 3 pin multipurpose all as specified and directed.

S&F modular socket outlet, 2 module, 2 pin 6A/ 3 pin 16 Amps, multipurpose all as specified and directed.

S&F modular fan regulator, step type, 2 module, suitable for 1200/1400mm sweep, 230 volts, AC, all as specified and directed.

S&F in repairs ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F in repairs call bell, ding dong, 230 volts AC supply all as specified and directed.

S&F in repairs surface mounting LED light fitting, 1x 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 20W LED, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F in repairs surface mounting LED light fitting, 1x 10W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 10W LED, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F in repairs 42 Watts LED glare free luminaire recess mounted in square profile 2ft x 2ft size with 42 W high brightness SMD LEDs including electronic driver etc. complete with all accessories internally pre wired including cutting of false ceiling sheet to required size and fixing aluminium strip as per the existing size in false ceiling for fixing of light fitting and providing aluminium strip supports as reqd and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: HAVELLS VENUS NEO HE 2x2 or equivalent in CG/ Philips/ Wipro

S&F in repairs 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP66 protection, 6000K and impact resistance IK07, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of street lighT bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F ceiling fan, 230 volts, single phase, 1200mm sweep, with all accessories complete including taking down existing unserviceable ceiling fan of any description and size and depositing in MES Store yard all as specified and as directed. Make: HAVELLS Model No. ES-50 or equivalent model in makes Crompton Greaves/ USHA

S&F exhaust fan, 250mm sweep, 1200 RPM, 230 Volts, single phase, PVC body with gravity shutter and fixing arrangements with fixing bolts and provision of 3 core flexible copper conductor cable of size 1.5sqmm size from ceiling rose to connector of exhaust fan and testing all as specified as directed. Make: Ventil Air-DX model of HAVELLS or equivalent model in USHA/ KHAITAN/ CROMPTON GREAVES

S&F wall mounting fan, 230 volts, single phase, 300mm sweep, with all accessories complete including provision of suitable clamps for fixing to wall and making good disturbed surfaces matching with the existing surface complete all as specified and as directed. Make: HAVELLS Model No. D'zire or equivalent model in makes Crompton Greaves/ USHA

M&L for 50mm dia GI pipe medium grade cut to required length as per site requirement and fixed into walls in single piece without any joints as in supports for hanging of ceiling fans complete all as specified and directed.

S&F in repairs, MCB DB TPN 4 Way with 200 Amps rated bus bars double door type, fixed to wall and making good disturbed surfaces all as specified and directed.

S&F in repairs, MCB DB SPN 8 Way with 100 Amps rated bus bars double door type, fixed to wall and making good disturbed surfaces all as specified and directed.

S&F in repairs MCB TPN 63A 10KA 'C' series 50Hz AC supply all as specified and as directed.

S&F in repairs MCB DP 63A 10KA 'C' series 50Hz AC supply all as specified and as directed.

S&F in repairs MCB SP 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

M/S SAMARTH CONSTRUCTIONS

M/S VISHWAROOP ELECTRONICS AND ELECTRICALS

M/s. KIRAN M CHOUGULE

ASHIRWAD ELECTRICALS

M/s A N Kalbhavi

ASHOK M RAJGOLKAR

SHRI.H.R.PATIL

RAJENDRA KRISHNA SARAF