Construction of Model Registry Office for Sub Registrar At Akaltara

DETAIL ESTIMATE AND ABSTRACT FOR CONSTRUCTION OF TAHSIL OFFICE BHILAI 03 DISTT DURG CHHATTISGARH

CIVIL WORK & WATER SUPPLY

S. No. I. No. PARTICULAR Measurement QTY UNIT RATE AMOUNT

PART A CIVIL WORK

1 1.2 Surface dressing of the ground including removing vegetation and making up undulations and in-equalities not exceeding 15 cms in depth/ height including disposal of rubbish upto 1.5 m lift and lead upto 50m (at least 5m away from the dressed area). 1 45.00 15.30 688.50 sqm 7.20 4957.20

2 1.1 Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.

1.1.1 In all types of soils.

Horizontel 2 42.30 0.30 0.20 5.08

3 1.6 Extra for every additional lift of 1.5 m or part thereof.

1.6.1 All types of soils

4 1.18 Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

horizontal 2 42.30 0.30 0.10 2.54

tahsil court 1 6.20 4.20 1.00 26.04

nayab tahsildar 1 6.20 4.20 1.00 26.04

retiring room 1 3.00 4.20 1.00 12.60

tahsil office 1 6.20 4.20 1.00 26.04

retiring room 1 3.00 4.20 1.00 12.60

patwari room 1 3.00 4.20 1.00 12.60

revenu inspector room 1 4.20 7.50 1.00 31.50

entrance hall 1 5.30 4.20 1.00 22.26

5 3.1 Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work.

3.1.3 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size).

Horizontel 2 42.30 0.30 0.10 2.54

tahsil court 1 6.20 4.20 0.10 2.60

nayab tahsildar 1 6.20 4.20 0.10 2.60

retiring room 1 3.00 4.20 0.10 1.26

tahsil office 1 6.20 4.20 0.10 2.60

record room 1 3.00 4.20 0.10 1.26

retiring room 1 3.00 4.20 0.10 1.26

patwari room 1 3.00 4.20 0.10 1.26

record room 1 3.00 4.20 0.10 1.26

revenu inspector room 1 4.20 7.50 0.10 3.15

entrance hall 1 5.30 4.20 0.10 2.23

6 1.18 Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in each deposited layer by ramming and watering with

For Footing (Total Excavated Earth) 277.63

Deduct : PCC Work 25.98

7 3.3 Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work.

3.3.1 M-20 Grade

Column upto Plinth 59 0.20 0.40 1.70 8.02

For ground/plinth Beam

tahsil court 2 6.20 0.20 0.40 0.99

tahsil court 2 4.20 0.20 0.40 0.67

nayab tahsildar room 2 6.20 0.20 0.40 0.99

nayab tahsildar room 2 4.20 0.20 0.40 0.67

retiring room 2 3.00 0.20 0.40 0.48

retiring room 2 4.20 0.20 0.40 0.67

tahsil office 2 6.20 0.20 0.40 0.99

tahsil office 2 4.20 0.20 0.40 0.67

record room 2 3.00 0.20 0.40 0.48

record room 1 4.20 0.20 0.40 0.34

retiring room 2 3.00 0.20 0.40 0.48

retiring room 1 4.20 0.20 0.40 0.34

patwari room 2 3.00 0.20 0.40 0.48

patwari room 2 4.20 0.20 0.40 0.67

record room 2 3.00 0.20 0.40 0.48

revenu inspector room 2 4.20 0.20 0.40 0.67

revenu inspector room 2 7.50 0.20 0.40 1.20

entrance hall 1 5.30 0.20 0.40 0.42

entrance hall 1 4.20 0.20 0.40 0.34

projection 10 0.50 0.20 0.40 0.40

For Lintel Beam

tahsil court 2 6.20 0.20 0.20 0.50

tahsil court 2 4.20 0.20 0.20 0.34

nayab tahsildar room 2 6.20 0.20 0.20 0.50

nayab tahsildar room 1 4.20 0.20 0.20 0.17

retiring room 2 3.00 0.20 0.20 0.24

retiring room 1 4.20 0.20 0.20 0.17

tahsil office 2 6.20 0.20 0.20 0.50

tahsil office 2 4.20 0.20 0.20 0.34

record room 2 3.00 0.20 0.20 0.24

record room 1 4.20 0.20 0.20 0.17

retiring room 2 3.00 0.20 0.20 0.24

retiring room 1 4.20 0.20 0.20 0.17

patwari room 2 3.00 0.20 0.20 0.24

patwari room 1 4.20 0.20 0.20 0.17

record room 2 3.00 0.20 0.20 0.24

revenu inspector room 2 4.20 0.20 0.20 0.34

revenu inspector room 2 7.50 0.20 0.20 0.60

entrance hall 1 5.30 0.20 0.20 0.21

entrance hall 1 4.20 0.20 0.20 0.17

projection 10 0.50 0.20 0.20 0.20

tahsil court 2 6.20 0.20 0.40 0.99

tahsil court 2 4.20 0.20 0.40 0.67

nayab tahsildar room 2 6.20 0.20 0.40 0.99

nayab tahsildar room 1 4.20 0.20 0.40 0.34

retiring room 2 3.00 0.20 0.40 0.48

retiring room 1 4.20 0.20 0.40 0.34

tahsil office 2 6.20 0.20 0.40 0.99

tahsil office 2 4.20 0.20 0.40 0.67

record room 2 3.00 0.20 0.40 0.48

record room 1 4.20 0.20 0.40 0.34

retiring room 2 3.00 0.20 0.40 0.48

retiring room 1 4.20 0.20 0.40 0.34

patwari room 2 3.00 0.20 0.40 0.48

patwari room 1 4.20 0.20 0.40 0.34

record room 2 3.00 0.20 0.40 0.48

revenu inspector room 2 4.20 0.20 0.40 0.67

revenu inspector room 2 7.50 0.20 0.40 1.20

entrance hall 1 5.30 0.20 0.40 0.42

entrance hall 1 4.20 0.20 0.40 0.34

projection 10 0.50 0.20 0.40 0.40

8 3.4 Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Above Plinth 124.87 cum 97.50 12174.44

9 2.1 Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for:

A 2.1.1 Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level.

For Ground Beam

tahsil court 4 6.20 0.40 9.92

tahsil court 4 4.20 0.40 6.72

nayab tahsildar room 4 6.20 0.40 9.92

nayab tahsildar room 4 4.20 0.40 6.72

retiring room 4 3.00 0.40 4.80

retiring room 2 4.20 0.40 3.36

sdo court 4 6.20 0.40 9.92

sdo court 2 4.20 0.40 3.36

tahsil office 4 6.20 0.40 9.92

tahsil office 4 4.20 0.40 6.72

record room 4 3.00 0.40 4.80

record room 2 4.20 0.40 3.36

malkhana 4 3.00 0.40 4.80

malkhana 2 4.20 0.40 3.36

najir room 4 3.00 0.40 4.80

najir room 2 4.20 0.40 3.36

retiring room 4 3.00 0.40 4.80

retiring room 2 4.20 0.40 3.36

sdo court 4 6.20 0.40 9.92

sdo court 2 4.20 0.40 3.36

water room 4 4.20 0.40 6.72

water room 4 1.20 0.40 1.92

patwari room 4 3.00 0.40 4.80

patwari room 2 4.20 0.40 3.36

record room 4 3.00 0.40 4.80

revenu inspector room 4 4.20 0.40 6.72

revenu inspector room 4 7.50 0.40 12.00

entrance hall 4 5.30 0.40 8.48

entrance hall 2 4.20 0.40 3.36

projection 20 0.50 0.40 4.00

B 2.1.5 Columns, Pillars, Piers and likes- rectangular or square in shape

C 2.1.8 Beams, lintels, cantilevers & walls

For Lintel Beam

tahsil court 4 6.20 0.20 4.96

tahsil court 4 4.20 0.20 3.36

nayab tahsildar room 4 6.20 0.20 4.96

nayab tahsildar room 2 4.20 0.20 1.68

retiring room 4 3.00 0.20 2.40

retiring room 2 4.20 0.20 1.68

sdo court 4 6.20 0.20 4.96

sdo court 2 4.20 0.20 1.68

tahsil office 4 6.20 0.20 4.96

tahsil office 4 4.20 0.20 3.36

record room 4 3.00 0.20 2.40

record room 2 4.20 0.20 1.68

malkhana 4 3.00 0.20 2.40

malkhana 2 4.20 0.20 1.68

najir room 4 3.00 0.20 2.40

najir room 2 4.20 0.20 1.68

retiring room 4 3.00 0.20 2.40

retiring room 2 4.20 0.20 1.68

sdo court 4 6.20 0.20 4.96

sdo court 2 4.20 0.20 1.68

water room 4 4.20 0.20 3.36

water room 4 1.20 0.20 0.96

patwari room 4 3.00 0.20 2.40

patwari room 2 4.20 0.20 1.68

record room 4 3.00 0.20 2.40

revenu inspector room 4 4.20 0.20 3.36

revenu inspector room 4 7.50 0.20 6.00

entrance hall 2 5.30 0.20 2.12

entrance hall 2 4.20 0.20 1.68

projection 20 0.50 0.20 2.00

tahsil court 4 6.20 0.40 9.92

tahsil court 4 4.20 0.40 6.72

nayab tahsildar room 4 6.20 0.40 9.92

nayab tahsildar room 2 4.20 0.40 3.36

retiring room 4 3.00 0.40 4.80

retiring room 2 4.20 0.40 3.36

sdo court 4 6.20 0.40 9.92

sdo court 2 4.20 0.40 3.36

tahsil office 4 6.20 0.40 9.92

tahsil office 4 4.20 0.40 6.72

record room 4 3.00 0.40 4.80

record room 2 4.20 0.40 3.36

malkhana 4 3.00 0.40 4.80

malkhana 2 4.20 0.40 3.36

najir room 4 3.00 0.40 4.80

najir room 2 4.20 0.40 3.36

retiring room 4 3.00 0.40 4.80

retiring room 2 4.20 0.40 3.36

sdo court 4 6.20 0.40 9.92

sdo court 2 4.20 0.40 3.36

water room 4 4.20 0.40 6.72

water room 4 1.20 0.40 1.92

patwari room 4 3.00 0.40 4.80

patwari room 2 4.20 0.40 3.36

record room 4 3.00 0.40 4.80

revenu inspector room 4 4.20 0.40 6.72

revenu inspector room 4 7.50 0.40 12.00

entrance hall 2 5.30 0.40 4.24

entrance hall 2 4.20 0.40 3.36

projection 20 0.50 0.40 4.00

D 2.1.7 Suspended floors, roofs, access Kitchen Platform, balconies (plain surfaces) and shelves (cast in situ)

outer projection 2 42.30 0.50 42.30

outer projection 2 14.50 0.50 14.50

tahsil court 1 6.20 4.20 26.04

nayab tahsildar 1 6.20 4.20 26.04

retiring room 1 3.00 4.20 12.60

tahsil office 1 6.20 4.20 26.04

record room 1 3.00 4.20 12.60

malkhana 1 3.00 4.20 12.60

najir room 1 3.00 4.20 12.60

retiring room 1 3.00 4.20 12.60

water room 1 3.00 1.40 4.20

patwari room 1 3.00 4.20 12.60

record room 1 3.00 4.20 12.60

revenu inspector room 1 4.20 7.50 31.50

entrance hall 1 5.30 4.20 22.26

outer projection 2 42.30 0.10 8.46

E 2.1.13 Weather shade, chhajja, Cornices and mouldings

chajja front 2 42.30 0.10 8.46

chajja side 4 0.50 0.10 0.20

chajja front 2 12.30 0.10 2.46

chajja side 4 0.50 0.10 0.20

chajja front 12 3.00 0.10 3.60

chajja side 12 0.50 0.10 0.60

10 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire in foundation and plinth all complete:

3.12.1 Thermo-Mechanically treated bars FE 415 (Make:- Tata / Sail / Goel /Jindal /Gk or Equivalent)

11 3.13 Providing and laying damp proof course (upto 50mm thick) with plain cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20mm nominal size) including form work.

12 7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:

7.5.3 Cement Mortar 1:5 (1 cement : 5 coarse sand)

13 7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:

7.5.4 Cement Mortar 1:6 (1 cement : 6 coarse sand)

tahsil court 2 6.20 0.20 3.00 7.44

tahsil court 2 4.20 0.20 3.00 5.04

nayab tahsildar room 2 6.20 0.20 3.00 7.44

nayab tahsildar room 1 4.20 0.20 3.00 2.52

retiring room 2 3.00 0.20 3.00 3.60

retiring room 1 4.20 0.20 3.00 2.52

tahsil office 2 6.20 0.20 3.00 7.44

tahsil office 2 4.20 0.20 3.00 5.04

record room 2 3.00 0.20 3.00 3.60

record room 1 4.20 0.20 3.00 2.52

retiring room 2 3.00 0.20 3.00 3.60

retiring room 1 4.20 0.20 3.00 2.52

patwari room 2 3.00 0.20 3.00 3.60

patwari room 1 4.20 0.20 3.00 2.52

record room 2 3.00 0.20 3.00 3.60

revenu inspector room 2 4.20 0.20 3.00 5.04

revenu inspector room 2 7.50 0.20 3.00 9.00

entrance hall 1 5.30 0.20 3.00 3.18

entrance hall 1 4.20 0.20 3.00 2.52

projection 10 0.50 0.20 3.00 3.00

Deduction of opening

Hence the nett oty A-B 162.70 cum 3263.00 530877.05

14 7.6 Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

15 7.11 Half brick thick brick masonry with fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in superstructure above plinth level upto plinth level:

7.11.4 Cement Mortar 1:4 (1 cement : 4 coarse sand)

16 7.12 Extra for half brick work in superstructure above plinth level for every story or part thereof in addition to rate for upto plinth level: 44.28 sqm 11.00 487.08

17 7.20 Extra for providing and placing in position hopping 25x1.60 mm or 2 Nos 6mm dia MS bars reinforcement at every third course of half brick masonry. 44.28 sqm 62.50 2767.50

18 8.1 Providing wood work in frames of doors, windows, clerestory windows and other frames wrought framed and fixed in position.

8.1.2 Sal, bijasal, benteak, khair, haldu

19 8.36 Providing and fixing commercial grade water proof ply for wall paneling on wooden frame with necessary nails complete as required.

20 8.11 Providing and fixing powder coated M.S. sliding door bolts with bolts, nuts and necessary iron screws

21 8.115. Providing and fixing powder coated M.S. tower bolts (Barrel type) with necessary iron screws:

22 8.116. Providing and fixing powder coated M.S. handles with necessary iron screws:

23 8.119. Providing and fixing powder coated MS hanging door stopper with necessary powder coated MS steel screws complete. 1 30.00 30.00 each 15.00 450.00

24 9.18 Providing and fixing in position doors, windows and ventilators frames made of cold rolled pressed steel sheet framed profiles made from commercial M.S. Sheets conforming to I.S. 513 of 1973 and as per general specifications of I.S 4351 including hinges jamb, lock jamb, steel butt hinges, base tie, joints mitred and welded with 10cm long legs of size 15x3mm M.S. flat, embedded in cement concrete blocks 15x10x10cm size of grade M-10 or rawl plugs and screws or with fixing clips or with bolts and nuts including neatly compacted filling M-10 cement concrete inprofile section applying a priming coat of red oxide zinc chromate primer.

9.18.5 Double rebate 115mmx50mm size, 1.6mm thick sheet 6 7.20 43.20

24 8.12 Providing and fixing flush door shutters, conforming to IS : 2202 (Part-I), decorative type core of block board construction with frame of first class hard wood and well matched teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters excluding hinges. (Make:- Green Board/ National/ Centuary or Equivalent)

8.12.2 35 mm. thick (single leaf)

25 9.15 Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer.

26 8.148 Providing and fixing factory made UPVC door frame made of UPVC profile section having an overall dimension as below (tolerance ± 1mm) with wall thickness 2.0mm ± 0.2mm, corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19mm and 1mm ± 0.1mm wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-in-charge 7 0.80 2.10 11.76 Mtr 196.00 2304.96

27 8.150 Providing and fixing factory made 25mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762mm X 25mm or less as per requirement with an average wall thickness of 1mm ± 0.3mm. PVC foam end cap of size 23x10mm are provided on both vertical edges to ensure the overall thickness of 25mm. An M.S. tube having dimensions 19mm x 19mm is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25mm X 11mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufactures' specification. 7 0.80 2.10 11.76 SQM 2583.00 30376.08

28 9.53 Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side having 12 mm air gap including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. complete.

29 9.34 Providing and fixing stainless wire gauge of average width of aperture 1.56mm with wire of 0.35mm to existing steel door, window shutter frames with necessary M.S. strip beading etc. complete.

30 11.41 Providing and fixing chicken mesh weighting not less than 250 gms/sqm as per IS : specification in the required width with 40mm long steel nails on vertical and horizontal surface near R.C.C. and brick walls junctions including scaffolding and all lead and lifts etc. complete before plastering upto 10mts in height.

31 12.79 Providing and laying vitrified floor tiles with double charge/ multi charge (minimum 2.0 mm thick layer) with water absorption less than 0.5% and conforming to IS : 15622 of approved make in all colours and shades and size mentioned below (+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.

12.79.1 Size 600x600mm thickness 9 to 10 mm

tahsil court 1 6.20 4.20 26.04

nayab tahsildar 1 6.20 4.20 26.04

retiring room 1 3.00 4.20 12.60

tahsil office 1 6.20 4.20 26.04

record room 1 3.00 4.20 12.60

malkhana 1 3.00 4.20 12.60

najir room 1 3.00 4.20 12.60

retiring room 1 3.00 4.20 12.60

water room 1 3.00 1.40 4.20

patwari room 1 3.00 4.20 12.60

record room 1 3.00 4.20 12.60

revenu inspector room 1 4.20 7.50 31.50

entrance hall 1 5.30 4.20 22.26

32 12.36 Chequered terrazzo tiles 22 mm thick with graded marble chips of size upto 6mm in floors on 25mm thick bed of cement mortar 1:6 (1 cement : 6 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles including grinding rubbing and polishing complete.

12.36.2 Medium shade using approximately. 50% white cement and 50% ordinary cement 1 6.00 4.00 24.00

33 12.74 Providing and fixing rectified glazed ceramic tiles of 1st quality conforming to IS : 15622-2017 of approved make,in colours, shades over 20 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete.

12.74.1 Size 300x300mm thickness 7 to 8 mm

34 12.75 Providing and fixing rectified glazed ceramic wall/dado tiles of 1st quality conforming to IS : 15622-2017 of approved make,in colours, shades on wall /dado over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete.

12.75.1 Size 300x450mm thickness 7 to 8 mm

35 11.1 Providing and making 6mm thick cement plaster of mix:

11.1.2 In Cement mortar 1:4 (1 cement : 4 fine sand)

Shuttering of suspended floor 489.52

chajja shuttering 79.12

36 11.2 Providing and making 12mm thick cement plaster of mix:

11.2.4 In Cement Mortar 1:5 (1 cement : 5 fine sand)

tahsil court 2 6.20 3.60 44.64

tahsil court 2 4.20 3.60 30.24

nayab tahsildar room 2 6.20 3.60 44.64

nayab tahsildar room 1 4.20 3.60 15.12

retiring room 2 3.00 3.60 21.60

retiring room 1 4.20 3.60 15.12

tahsil office 2 6.20 3.60 44.64

tahsil office 2 4.20 3.60 30.24

record room 2 3.00 3.60 21.60

record room 1 4.20 3.60 15.12

malkhana 2 3.00 3.60 21.60

malkhana 1 4.20 3.60 15.12

najir room 2 3.00 3.60 21.60

najir room 1 4.20 3.60 15.12

retiring room 2 3.00 3.60 21.60

retiring room 1 4.20 3.60 15.12

water room 2 4.20 3.60 30.24

water room 2 1.20 3.60 8.64

patwari room 2 3.00 3.60 21.60

patwari room 1 4.20 3.60 15.12

record room 2 3.00 3.60 21.60

revenu inspector room 2 4.20 3.60 30.24

revenu inspector room 2 7.50 3.60 54.00

entrance hall 1 5.30 3.60 19.08

entrance hall 1 4.20 3.60 15.12

projection 10 0.50 3.60 18.00

TOTAL 1053.36 A

Side Gate 1 2.10 2.10 4.41

Hence the nett qty (A-B) 959.10 sqm

Total 12mm Plaster 959.10 Sqm 91.50 87757.65

37 11.3 Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix:

11.3.4 In Cement Mortar 1:5 (1 cement : 5 fine sand)

tahsil court 2 6.20 3.60 44.64

tahsil court 2 4.20 3.60 30.24

nayab tahsildar room 2 6.20 3.60 44.64

nayab tahsildar room 1 4.20 3.60 15.12

retiring room 2 3.00 3.60 21.60

retiring room 1 4.20 3.60 15.12

tahsil office 2 6.20 3.60 44.64

tahsil office 2 4.20 3.60 30.24

record room 2 3.00 3.60 21.60

record room 1 4.20 3.60 15.12

malkhana 2 3.00 3.60 21.60

malkhana 1 4.20 3.60 15.12

najir room 2 3.00 3.60 21.60

najir room 1 4.20 3.60 15.12

retiring room 2 3.00 3.60 21.60

retiring room 1 4.20 3.60 15.12

water room 2 4.20 3.60 30.24

water room 2 1.20 3.60 8.64

patwari room 2 3.00 3.60 21.60

patwari room 1 4.20 3.60 15.12

record room 2 3.00 3.60 21.60

revenu inspector room 2 4.20 3.60 30.24

revenu inspector room 2 7.50 3.60 54.00

entrance hall 1 5.30 3.60 19.08

entrance hall 1 4.20 3.60 15.12

projection 10 0.50 3.60 18.00

Total 15mm Plaster 1181.26 sqm 107.00 126394.82

38 14.13 Providing and applying 2mm thick ready mix exterior grade approved make putty (like Birla wall care, Alltek Superfine W/R of (NCL), Asian, ICI, Nerolac, J.K. wall putty) on walls to make the surface smooth and even.

As per 6mm Plaster 568.64

As per 12mm Plaster 959.10

As per 15mm Plaster 1181.26

39 14.9 Distempering with acrylic washable distemper to give an even shade.

14.9.1 On new work (Two or more coats

As per 6mm Inner Plaster 489.52

As per 12mm Plaster 959.10

40 14.15 Painting exterior surface with ACRYLIC SMOOTH exterior paint of required shade as per manufacturer's specifications to give protective and decorative finish including cleaning washing of surface etc. complete with:

14.15.1 On new work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

As per 15mm Plaster 1181.26 sqm 56.00 66150.56

41 14.22 Painting on new work (two or more coats) to give an even shade with:

14.22.1 Satin synthetic enamel paint

42 12.1 Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg/ sqm for receiving cement concrete floor including roughening cleaning etc complete.

43 4.22 Providing Water proofing treatment over Roof, Wall, Chhajjas, Balcony with Diamond Shield and Sealer coat or equivalent at leakage/ seepage area consisting of the operation

(i) Surface preparation roughening of surface, opening of cracks in ‘V’ groove in size of 5mm x 10m (WxD), filling of cracks with putty of Diamond shield with laying fiber glass mesh, Cleaning of surface by scrubbing with steel wire/ Nylon brush. Removing all dust particles and washing with adequate water to clean completely

(ii) Providing and applying 1st coat of diamond shield or equivalent compound (having two component dry powder 80% Chemical 20% (chemical having 30% solid contents) making flexible waterproof and protective modified mortar with minimum thickness 70-80 micron after proper mixing of both the parts of compound along with laying of fiber glass mesh (of weaving size of 10x10 yarn/inch duly coated with alkaline resistant polymer). Allow the coating to set in natural air for minimum 2 Hrs. After 1st coat apply 2nd coat with minimum thickness 100 micron of the same compound. Allow the 2nd coat to set in natural air for minimum 4 Hrs. Total consumption of the diamond shield or equivalent in both coat should be @ 17.90 kg for 10sqm area.

PART B WATERSUPPLY AND SANITARY WORK WORK

1 19.42 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 2 1000.00 2000.00 LTR 7.30 14600.00

2 19.7 Providing and fixing in position G.I B Class pipe line best Indian make complete with fittings, except controls such as cocks and valves fitted and fix to the walls with G.I approved clamps at any floor or buried under ground including making necessary chases and holes in walls and floors or trenching etc. complete with making good or refilling including painting of pipes.

3 18.76 Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete. a. 75mm dia Make: (Supreme/Finolex)

4 18.77 Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete.

A 18.77.1 Tee/ Tee with door/ Bend 45°/ Bend 90°

B 18.77.2 Double "Y" with or without door

C 18.77.3 Vent cowel

5 18.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ), 100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (same colour) conforming to IS : 7231, with flush bend and other fittings and fixtures complete including cutting and making good the walls and floors wherever required :

18.1.3 White Orissa pattern W.C. pan of size 580x440 mm 1 7.00 7.00 EACH 2899.00 20293.00

6 18.4 Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :

18.4.3 White wall hung type 1 1.00 1.00 EACH 4415.00 4415.00

7 18.17 Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required :

8 18.25 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

9 19.13 Providing and fixing 15 mm nominal bore Brass bib/stop cock of approved quality:

10 19.14 Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:

B 19.14.14 Soap dish plate 1 3.00 3.00 EACH 163.00 489.00

C 19.14.16 Towel rail (600mm long x 20mm dia) 1 7.00 7.00 EACH 338.00 2366.00

11 19.15 Providing and fixing stainless steel drain jali of approved make/quality. 1 10.00 10.00 EACH 51.00 510.00

12 18.30 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing

13 20.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete 150mm thick as per standard design

20.2.2 100 mm diameter S.W. pipe 1 20.00 20.00 each 357.00 7140.00

14 20.25 Providing and constructing brick masonry road gully chamber 50x45x60 cm with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal grating with frame complete as per standard design. 1 4.00 4.00 each 2872.00 11488.00

15 20.31 Providing and constructing soak pit 1.20x1.20x1.20m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. 1 1.00 1.00 each 1709.00 1709.00

16 9.11 Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rails of T-iron 40x40x6mm with 38mm steel pulleys complete with bolts, nuts, locking arrangement stoppers, handles including applying a priming coat of red oxide zinc chromate primer.

main gate 1 2.40 2.40 5.76

TOTAL 5848566.01

DETAIL ESTIMATE AND ABSTRACT FOR CONSTRUCTION OF TAHSIL OFFICE DARRI/HARDI BAZAR DISTT KORBA CHHATTISGARH

S.No SOR ITEM PARTICLAR OF ITEM NO. L B H/D QTY UNIT RATE AMOUNT

1 1.1 Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.

2 1.6 Extra for every additional lift of 1.5 m or part thereof.

3 1.18 Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete. TOTAL EXCAVATION 28.22

4 3.1 Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work.

3.1.3 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). 1 4.80 2.80 0.15 2.02 cum 2970.00 5987.52

5 3.2 Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work.

3.2.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm

Buffel Wall 2 2.00 0.10 1.50 0.60

7 3.9 Extra for precast PCC/ RCC work of any mix including form work, hoisting and fixing in Cement Mortar. 1:2 (1 Cement : 2 coarse sand) and finishing with cement plaster in Cement Mortar 1:3 (1 Cement : 3 coarse sand) but excluding reinforcement.

8 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire in foundation and plinth all complete:

3.12.2 Thermo-Mechanically treated bars FE 500D 10.0 70.00/Kg 700.56 Kg 54.50 38180.52

9 2.1 Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for:

2.1.7 Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ)

TOTAL QUANTITY 10.96 sqm 235.00 2575.60

2.1.8 Beams, lintels, cantilevers & walls

Buffel Wall 2 2.00 1.50 6.00

10 11.2 Providing and making 12mm thick cement plaster of mix:

11.2.1 In cement Mortar 1:3 (1 cement : 3 fine sand)

Buffel Wall 2 2 1.65 6.60

11 11.9 Extra for providing and mixing water proofing materials in cement plaster work in proportion as recommended by manufacturer. QTY. SAME AS ABOVE 43.40 Kg 43.50 1887.90

12 11.5 Neat Cement punning. QTY. SAME AS ABOVE 43.40 sqm 33.00 1432.20

13 9.6 Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of red oxide zinc chromate primer. 8.00 0.60 4.80

9.6.2 Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of red oxide zinc chromate primer. 4.5/kg 21.60 Kg 68.00 1468.80

Total Rs. 115926.37

DETAILLED AND ABSTRACT ESTIMATE FOR CONSTRUCTIN OF TAHSIL OFFICE DURG DISTT-DURG

S.NO. SOR. ITEM PARTICULAR OF ITEM NO. L B D QTY UNIT RATE AMOUNT

1 1.2 Surface dressing of the ground including removing vegetation and making up undulations and in-equalities not exceeding 15 cms in depth/ height including disposal of rubbish upto 1.5 m lift and lead upto 50m (at least 5m away from the dressed area) 1 X 1 45 15.3 688.5 SQM 7.2 4957.20

2 1.1 Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.

3 1.6 Extra for every additional lift of 1.5 m or part thereof.

1.6.1 All types of soils

4 1.17 Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50 M. and lift upto 1.5 M 1 X 1 139 138.81 CUM 65 9022.65

5 1.18 Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

Tahsil court 1 X 1 6.2 4.2 1 26.04

Nayab tahsildar 1 X 1 6.2 4.2 1 26.04

Reting room 1 X 1 3 4.2 1 12.6

Tahsil Office 1 X 1 6.2 4.2 1 26.04

Record Room 1 X 1 3 4.2 1 12.6

Malkhana 1 X 1 3 4.2 1 12.6

Retiring Room 1 X 1 3 4.2 1 12.6

Toilet 1 X 2 3 3 1 18

Water Room 1 X 1 3 1.4 1 4.2

Patwari 1 X 1 3 4.2 1 12.6

Record Room 1 X 1 3 4.2 1 12.6

Revenue Inspector 1 X 1 4.2 7.5 1 31.5

Entrance hall 1 X 1 5.3 4.2 1 22.26

6 3.1 Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work.1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size).

Tahsil court 1 X 1 6.2 4.2 0.1 2.6

Nayab tahsildar 1 X 1 6.2 4.2 0.1 2.6

Reting room 1 X 1 3 4.2 0.1 1.26

Tahsil Office 1 X 1 6.2 4.2 0.1 2.6

Record Room 1 X 1 3 4.2 0.1 1.26

Malkhana 1 X 1 3 4.2 0.1 1.26

Retiring Room 1 X 1 3 4.2 0.1 1.26

Water Room 1 X 1 3 1.4 0.1 0.42

Record Room 1 X 1 3 4.2 0.1 1.26

Revenue Inspector 1 X 1 4.2 7.5 0.1 3.15

Entrance hall 1 X 1 5.3 4.2 0.1 2.23

7 7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:Cement Mortar 1:5 (1 cement : 5 coarse sand)

8 3.13 Providing and laying damp proof course (upto 50mm thick) with plain cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20mm nominal size) including form work.

9 3.2 Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work.1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size).

Tahsil court 1 X 2 6.2 0.2 0.4 0.99

Tahsil court 1 X 2 4.2 0.2 0.4 0.67

Nayab Tahsildar 1 X 2 6.2 0.2 0.4 0.99

Nayab Tahsildar 1 X 2 4.2 0.2 0.4 0.67

Retiring Room 1 X 2 3 0.2 0.4 0.48

Retiring Room 1 X 1 4.2 0.2 0.4 0.34

Tahsil Office 1 X 2 6.2 0.2 0.4 0.99

Tahsil Office 1 X 2 4.2 0.2 0.4 0.67

Record Room 1 X 2 3 0.2 0.4 0.48

Record Room 1 X 1 4.2 0.2 0.4 0.34

Malkhana 1 X 2 3 0.2 0.4 0.48

Retiring Room 1 X 2 3 0.2 0.4 0.48

Retiring Room 1 X 1 4.2 0.2 0.4 0.34

Water Room 1 X 2 1.2 0.2 0.4 0.67

Water Room 1 X 2 3 0.2 0.4 0.19

Record Room 1 X 2 3 0.2 0.4 0.48

Revenue Inspector 1 X 2 4.2 0.2 0.4 0.67

Revenue Inspector 1 X 2 7.5 0.2 0.4 1.2

Entrance hall 1 X 1 5.3 0.2 0.4 0.42

Entrance hall 1 X 1 4.2 0.2 0.4 0.34

Projection 1 X 10 0.5 0.2 0.4 0.4

Tahsil court 1 X 2 6.2 0.2 0.2 0.5

Tahsil court 1 X 2 4.2 0.2 0.2 0.34

Nayab Tahsildar 1 X 2 6.2 0.2 0.2 0.5

Nayab Tahsildar 1 X 1 4.2 0.2 0.2 0.17

Retiring Room 1 X 2 3 0.2 0.2 0.24

Retiring Room 1 X 1 4.2 0.2 0.2 0.17

Tahsil Office 1 X 2 6.2 0.2 0.2 0.5

Tahsil Office 1 X 2 4.2 0.2 0.2 0.34

Record Room 1 X 2 3 0.2 0.2 0.24

Record Room 1 X 1 4.2 0.2 0.2 0.17

Malkhana 1 X 2 3 0.2 0.2 0.24

Retiring Room 1 X 2 3 0.2 0.2 0.24

Retiring Room 1 X 1 4.2 0.2 0.2 0.17

Water Room 1 X 2 4.2 0.2 0.2 0.34

Water Room 1 X 2 1.2 0.2 0.2 0.1

Record Room 1 X 2 3 0.2 0.2 0.24

Revenue Inspector 1 X 2 4.2 0.2 0.2 0.34

Revenue Inspector 1 X 2 7.5 0.2 0.2 0.6

Entrance hall 1 X 1 5.3 0.2 0.2 0.21

Entrance hall 1 X 1 4.2 0.2 0.2 0.17

Projection 1 X 10 0.5 0.2 0.2 0.2

Tahsil court 1 X 2 6.2 0.2 0.4 0.99

Tahsil court 1 X 2 4.2 0.2 0.4 0.67

Nayab Tahsildar 1 X 2 6.2 0.2 0.4 0.99

Nayab Tahsildar 1 X 1 4.2 0.2 0.4 0.34

Retiring Room 1 X 2 3 0.2 0.4 0.48

Retiring Room 1 X 1 4.2 0.2 0.4 0.34

Tahsil Office 1 X 2 6.2 0.2 0.4 0.99

Tahsil Office 1 X 2 4.2 0.2 0.4 0.67

Record Room 1 X 2 3 0.2 0.4 0.48

Record Room 1 X 1 4.2 0.2 0.4 0.34

Malkhana 1 X 2 3 0.2 0.4 0.48

Retiring Room 1 X 2 3 0.2 0.4 0.48

Retiring Room 1 X 1 4.2 0.2 0.4 0.34

Water Room 1 X 2 4.2 0.2 0.4 0.67

Water Room 1 X 2 1.2 0.2 0.4 0.19

Record Room 1 X 2 3 0.2 0.4 0.48

Revenue Inspector 1 X 2 4.2 0.2 0.4 0.67

Revenue Inspector 1 X 2 7.5 0.2 0.4 1.2

Entrance hall 1 X 1 5.3 0.2 0.4 0.42

Entrance hall 1 X 1 4.2 0.2 0.4 0.34

Projection 1 X 10 0.5 0.2 0.4 0.4

10 3.4 Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: B+C 124.87 CUM 97.5 12174.83

11 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire in foundation and plinth all complete: 1 X 1 220 110 24166.67 K.G 54.5 1317083.52

12 2.1 Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level.

Tahsil court 1 X 4 6.2 0.4 9.92

Tahsil court 1 X 4 4.2 0.4 6.72

Nayab Tahsildar 1 X 4 6.2 0.4 9.92

Nayab Tahsildar 1 X 4 4.2 0.4 6.72

Office 1 X 4 3 0.4 4.8

Retiring Room 1 X 4 3 0.4 4.8

Retiring Room 1 X 2 4.2 0.4 3.36

SDO Court 1 X 4 6.2 0.4 9.92

SDO Court 1 X 2 4.2 0.4 3.36

Tahsil Office 1 X 4 6.2 0.4 9.92

Tahsil Office 1 X 4 4.2 0.4 6.72

Record Room 1 X 4 3 0.4 4.8

Record Room 1 X 2 4.2 0.4 3.36

Malkhana 1 X 4 3 0.4 4.8

Malkhana 1 X 2 4.2 0.4 3.36

Retiring Room 1 X 4 3 0.4 4.8

Retiring Room 1 X 2 4.2 0.4 3.36

SDO Court 1 X 4 6.2 0.4 9.92

SDO Court 1 X 2 4.2 0.4 3.36

Toitel 1 X 10 3 0.4 12

Toitel 1 X 10 3 0.4 12

Water Room 1 X 4 4.2 0.4 6.72

Water Room 1 X 4 1.2 0.4 1.92

Patwari 1 X 4 3 0.4 4.8

Patwari 1 X 2 4.2 0.4 3.36

Record Room 1 X 4 3 0.4 4.8

Revenue Inspector 1 X 4 4.2 0.4 6.72

Revenue Inspector 1 X 4 7.5 0.4 12

Entrance hall 1 X 4 5.3 0.4 8.48

Entrance hall 1 X 2 4.2 0.4 3.36

Projection 1 X 20 0.5 0.4 4

13 2.1.5 Columns, Pillars, Piers and likesrectangular or square in shape

14 2.1.8 Beams, Lintels, cantilevers & wall

Tahsil court 1 X 4 6.2 0.2 4.96

Tahsil court 1 X 4 4.2 0.2 3.36

Nayab Tahsildar 1 X 4 6.2 0.2 4.96

Nayab Tahsildar 1 X 2 4.2 0.2 1.68

Office 1 X 4 3 0.2 2.4

Retiring Room 1 X 4 3 0.2 2.4

Retiring Room 1 X 2 4.2 0.2 1.68

SDO Court 1 X 4 6.2 0.2 4.96

SDO Court 1 X 2 4.2 0.2 3.36

Tahsil Office 1 X 4 6.2 0.2 2.4

Tahsil Office 1 X 4 4.2 0.2 1.68

Record Room 1 X 4 3 0.2 2.4

Record Room 1 X 2 4.2 0.2 1.68

Malkhana 1 X 4 3 0.2 2.4

Malkhana 1 X 2 4.2 0.2 1.68

Retiring Room 1 X 4 3 0.2 2.4

Retiring Room 1 X 2 4.2 0.2 1.68

SDO Court 1 X 4 6.2 0.2 4.96

SDO Court 1 X 2 4.2 0.2 1.68

Toitel 1 X 10 3 0.2 6

Toitel 1 X 10 3 0.2 6

Water Room 1 X 4 4.2 0.2 3.36

Water Room 1 X 4 1.2 0.2 0.96

Patwari 1 X 4 3 0.2 2.4

Patwari 1 X 2 4.2 0.2 1.68

Record Room 1 X 4 3 0.2 2.4

Revenue Inspector 1 X 4 4.2 0.2 3.36

Revenue Inspector 1 X 4 7.5 0.2 6

Entrance hall 1 X 2 5.3 0.2 2.12

Entrance hall 1 X 2 4.2 0.2 1.68

Projection 1 X 20 0.5 0.2 2

Tahsil court 1 X 4 6.2 0.4 9.92

Tahsil court 1 X 4 4.2 0.4 6.72

Nayab Tahsildar 1 X 4 6.2 0.4 9.92

Nayab Tahsildar 1 X 2 4.2 0.4 3.36

Office 1 X 4 3 0.4 4.8

Retiring Room 1 X 4 3 0.4 4.8

Retiring Room 1 X 2 4.2 0.4 3.36

SDO Court 1 X 4 6.2 0.4 9.92

SDO Court 1 X 2 4.2 0.4 3.36

Tahsil Office 1 X 4 6.2 0.4 9.92

Tahsil Office 1 X 4 4.2 0.4 6.72

Record Room 1 X 4 3 0.4 4.8

Record Room 1 X 2 4.2 0.4 3.36

Malkhana 1 X 4 3 0.4 4.8

Malkhana 1 X 2 4.2 0.4 3.36

Retiring Room 1 X 4 3 0.4 4.8

Retiring Room 1 X 2 4.2 0.4 3.36

SDO Court 1 X 4 6.2 0.4 9.92

SDO Court 1 X 2 4.2 0.4 3.36

Toitel 1 X 10 3 0.4 12

Toitel 1 X 10 3 0.4 12

Water Room 1 X 4 4.2 0.4 6.72

Water Room 1 X 4 1.2 0.4 1.92

Patwari 1 X 4 3 0.4 4.8

Patwari 1 X 2 4.2 0.4 3.36

Record Room 1 X 4 3 0.4 4.8

Revenue Inspector 1 X 4 4.2 0.4 6.72

Revenue Inspector 1 X 4 7.5 0.4 12

Entrance hall 1 X 2 5.3 0.4 4.42

Entrance hall 1 X 2 4.2 0.4 3.36

Projection 1 X 20 0.5 0.4 4

15 2.1.13 Water shade, chhajja, Cornices and mouldings.

16 2.1.7 Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ)

Tahsil Court 1 X 1 6.2 4.2 26.04

Nayab Tahsildar 1 X 1 6.2 4.2 26.04

Office 1 X 1 3 4.2 12.6

Retiring Room 1 X 1 3 4.2 12.6

SDO Court 1 X 1 6.2 4.2 26.04

Tahsil Office 1 X 1 6.2 4.2 26.04

Record Room 1 X 1 3 4.2 12.6

Malkhana 1 X 1 3 4.2 12.6

Retiring Room 1 X 1 3 4.2 12.6

SDO Court 1 X 1 6.2 4.2 26.04

Toilet 1 X 2 3 3 18

Toilet 1 X 1 3 2.6 7.8

Water Room 1 X 1 3 1.4 4.2

Patwari 1 X 1 3 4.2 12.6

Record Room 1 X 1 3 4.2 12.6

Revenue Inspector 1 X 1 4.2 7.5 31.5

Entrance hall 1 X 1 5.3 4.2 22.26

17 4.22 Providing Water proofing treatment over Roof, Wall, Chhajjas, Balcony with Diamond Shield and Sealer coat or equivalent at leakage/ seepage area consisting of the operation: (i) Surface preparation roughening of surface, opening of cracks in ‘V’ groove in size of 5mm x 10m (WxD), filling of cracks with putty of Diamond shield with laying fiber glass mesh, Cleaning of surface by scrubbing with steel wire/ Nylon brush. Removing all dust particles and washing with adequate water to clean completely. (ii) Providing and applying 1st coat of diamond shield or equivalent compound (having two component dry powder 80% Chemical 20% (chemical having 30% solid contents) making flexible waterproof and protective modified mortar with minimum thickness 70-80 micron after proper mixing of both the parts of compound along with laying of fiber glass mesh (of weaving size of 10x10 yarn/inch duly coated with alkaline resistant polymer). Allow the coating to set in natural air for minimum 2 Hrs. After 1st coat apply 2nd coat with minimum thickness 100 micron of the same compound. Allow the 2nd coat to set in natural air for minimum 4 Hrs. Total consumption of the diamond shield or equivalent in both coat should be @ 17.90 kg for 10sqm area.

18 12.1 Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg/ sqm for receiving cement concrete floor including roughening cleaning etc complete. 1 X 1 481 480.52 SQM 34 16337.68

19 7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in: Cement Mortar 1:6 (1 cement : 6 coarse sand)

Tahsil court 1 X 2 6.2 0.2 3 7.44

Tahsil court 1 X 2 4.2 0.2 3 5.04

Nayab Tahsildar 1 X 2 6.2 0.2 3 7.44

Nayab Tahsildar 1 X 1 4.2 0.2 3 2.52

Retiring Room 1 X 2 3 0.2 3 3.6

Retiring Room 1 X 1 4.2 0.2 3 2.52

SDO court 1 X 2 6.2 0.2 3 7.44

SDO court 1 X 1 4.2 0.2 3 2.52

Tahsil Office 1 X 2 6.2 0.2 3 7.44

Tahsil Office 1 X 2 4.2 0.2 3 5.04

Record Room 1 X 2 3 0.2 3 3.6

Record Room 1 X 1 4.2 0.2 3 2.52

Malkhana 1 X 2 3 0.2 3 3.6

Malkhana 1 X 1 4.2 0.2 3 2.52

Retiring Room 1 X 2 3 0.2 3 3.6

Retiring Room 1 X 1 4.2 0.2 3 2.52

SDO court 1 X 2 6.2 0.2 3 7.44

SDO court 1 X 1 4.2 0.2 3 2.52

Water Room 1 X 2 4.2 0.2 3 5.04

Water Room 1 X 2 1.2 0.2 3 1.44

Patwari 1 X 2 3 0.2 3 3.6

Record Room 1 X 2 3 0.2 3 3.6

Revenue Inspector 1 X 2 4.2 0.2 3 5.04

Revenue Inspector 1 X 2 7.5 0.2 3 9

Entrance hall 1 X 1 5.3 0.2 3 3.18

Entrance hall 1 X 1 4.2 0.2 3 2.52

Projection 1 X 10 0.5 0.2 3 3

20 7.6 Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 1 X 1 166 165.58 CUM 121 20035.18

21 7.11 Half brick thick brick masonry with fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in superstructure above plinth level upto plinth level:

22 7.20 Extra for providing and placing in position hopping 25x1.60 mm or 2 Nos 6mm dia MS bars reinforcement at every third course of half brick masonry 1 X 1 31.9 31.86 SQM 11 350.46

23 7.12 Extra for half brick work in superstructure above plinth level for every story or part thereof in addition to rate for upto plinth level: 1 X 1 31.9 31.86 SQM 62.5 1991.25

24 11.1 Providing and making 6mm thick cement plaster of mix:In Cement mortar 1:4 (1 cement : 4 fine sand)

chhajja shuttering 1 X 1 79.1 79.12 SQM 87 6883.44

25 11.2 Providing and making 12mm thick cement plaster of mix:In Cement Mortar 1:6 (1 cement : 6 fine sand

Tahsil court 1 X 2 6.2 3.6 44.64

Tahsil court 1 X 2 4.2 3.6 30.24

Nayab Tahsildar 1 X 2 6.2 3.6 44.64

Nayab Tahsildar 1 X 1 4.2 3.6 15.12

Office 1 X 2 3 3.6 21.6

Retiring Room 1 X 2 3 3.6 21.6

Retiring Room 1 X 1 4.2 3.6 15.12

SDO court 1 X 2 6.2 3.6 44.64

SDO court 1 X 1 4.2 3.6 15.12

Tahsil Office 1 X 2 6.2 3.6 44.64

Tahsil Office 1 X 2 4.2 3.6 30.24

Record Room 1 X 2 3 3.6 21.6

Record Room 1 X 1 4.2 3.6 15.12

Malkhana 1 X 2 3 3.6 21.6

Malkhana 1 X 1 4.2 3.6 15.12

Retiring Room 1 X 2 3 3.6 21.6

Retiring Room 1 X 1 4.2 3.6 15.12

SDO court 1 X 2 6.2 3.6 44.64

SDO court 1 X 1 4.2 3.6 15.12

Toitel 1 X 10 3 3.6 108

Toitel 1 X 7 3 3.6 54

Water Room 1 X 2 4.2 3.6 30.24

Water Room 1 X 2 1.2 3.6 8.64

Patwari 1 X 2 3 3.6 21.6

Record Room 1 X 2 3 3.6 21.6

Revenue Inspector 1 X 2 4.2 3.6 30.24

Revenue Inspector 1 X 2 7.5 3.6 54

Entrance hall 1 X 1 5.3 3.6 19.08

Entrance hall 1 X 1 4.2 3.6 15.12

Projection 1 X 10 0.5 3.6 18

Side Gate 1 X -1 2.1 2.1 -4.41

26 11.3 Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix: In Cement Mortar 1:6 (1 cement : 6 fine sand)

Tahsil court 1 X 2 6.2 3.6 44.64

Tahsil court 1 X 2 4.2 3.6 30.24

Nayab Tahsildar 1 X 2 6.2 3.6 44.64

Nayab Tahsildar 1 X 1 4.2 3.6 15.12

Office 1 X 2 3 3.6 21.6

Retiring Room 1 X 2 3 3.6 21.6

Retiring Room 1 X 1 4.2 3.6 15.12

SDO court 1 X 2 6.2 3.6 44.64

SDO court 1 X 1 4.2 3.6 15.12

Tahsil Office 1 X 2 6.2 3.6 44.64

Tahsil Office 1 X 2 4.2 3.6 30.24

Record Room 1 X 2 3 3.6 21.6

Record Room 1 X 1 4.2 3.6 15.12

Malkhana 1 X 2 3 3.6 21.6

Malkhana 1 X 1 4.2 3.6 15.12

Retiring Room 1 X 2 3 3.6 21.6

Retiring Room 1 X 1 4.2 3.6 15.12

SDO court 1 X 2 6.2 3.6 44.64

SDO court 1 X 1 4.2 3.6 15.12

Toitel 1 X 10 3 3.6 108

Toitel 1 X 5 3 3.6 54

Water Room 1 X 2 4.2 3.6 30.24

Water Room 1 X 2 1.2 3.6 8.64

Patwari 1 X 2 3 3.6 21.6

Record Room 1 X 2 3 3.6 21.6

Revenue Inspector 1 X 2 4.2 3.6 30.24

Revenue Inspector 1 X 2 7.5 3.6 54

Entrance hall 1 X 1 5.3 3.6 19.08

Entrance hall 1 X 1 4.2 3.6 15.12

Projection 1 X 10 0.5 3.6 18

27 11.41 Providing and fixing chicken mesh weighting not less than 250 gms/ sqm as per IS : specification in the required width with 40mm long steel nails on vertical and horizontal surface near R.C.C. and brick walls junctions including scaffolding and all lead and lifts etc. complete before plastering upto 10mts in height.

Lintel Beam 2 X 1 100 0.4 80

28 12.79.1 Providing and laying double/multi charge (minimum 2.0mm thick layer) vitried floor tiles with water absorption less than 0.05% and conforming to IS : 15622-2017 of 1st quality of approved make in all colours and shade and size mentioned below (+/-10mm)laid on 20mm thick cement sand) including grauting the joints with white cement and matching pigments etc.complete. size 600x600mm thickness 9 to 10mm

Tahsil court 1 X 1 6.2 4.2 26.04

Nayab Tahsildar 1 X 1 6.2 4.2 26.04

Office 1 X 1 3 4.2 12.6

Retring Room 1 X 1 3 4.2 12.6

SDO Court 1 X 1 6.2 4.2 26.04

Tahsil Office 1 X 1 6.2 4.2 26.04

Record Room 1 X 1 3 4.2 12.6

Malkhana 1 X 1 3 4.2 12.6

Retring Room 1 X 1 3 4.2 12.6

SDO Court 1 X 1 6.2 4.2 26.04

Toilet 1 X 1 3 3 9

Toilet 1 X 1 3 2.6 7.8

Water Room 1 X 1 3 1.4 4.2

Patwari 1 X 1 3 4.2 12.6

Record Room 1 X 1 3 4.2 12.6

Revenue Inspector 1 X 1 4.2 7.2 31.5

Entrance hall 1 X 1 5.3 4.2 22.26

29 12.33 Chequerred precast cement concrete tiles 22mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tile including cleaning of joint etc complete on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) :

12.36.2 Medium shade using approximately. 50% white cement and 50% ordinary cement. 1 X 1 6 4 24 SQM 713 17112.00

30 12.74 Providing and fixing rectified glazed ceramic floor tiles of 1 st quality conforming to IS 15622-2017 of approved make in all colours shade over 20mm thick bed of cement mortar 1:3 (1 cement : 3 coars sand) and joiting with grey cement slueey @ 3.3 Kg per sqm. including pointing in the white cement mixed with matching pigment complete.

12.74.1 size 300x300mm thickness 7 to 8mm 1 X 1 1.8 1.8 3.24

31 12.75 Providing and fixing rectified glazed ceramic floor tiles of 1 st quality conforming to IS 15622-2017 of approved make in all colours shade over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coars sand) and joiting with grey cement slueey @ 3.3 Kg per sqm. including pointing in the white cement mixed with matching pigment complete.

12.75.1 size 300x450mm thickness 7 to 8mm

32 8.1 Providing wood work in frames of doors, windows, clerestory windows and other frames wrought framed and fixed in position.

33 8.36 Providing and fixing commercial grade water proof ply for wall paneling on wooden frame with necessary nails complete as required.

34 8.112 Providing and fixing powder coated M.S. sliding door bolts with bolts, nuts and necessary iron screws:

35 8.115 Providing and fixing powder coated M.S. tower bolts (Barrel type) with necessary iron screws:

36 8.116 Providing and fixing powder coated M.S. handles with necessary iron screws:

37 8.119 Providing and fixing powder coated MS hanging door stopper with necessary powder coated MS steel screws complete. 1 X 1 30 30 EACH 15 450.00

38 8.12.2 Providing and fixing flush door shutters, conforming to IS : 2202 (Part-I),decorative type core of block board construction with frame of first class hard wood and well matched teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters excluding hinges.

35 mm. thick (single leaf)

39 9.15 Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer.

40 8.148 Providing and fixing factory made UPVC door frame made of UPVC profile section having an overall dimension as below (tolerance ± 1mm) with wall thickness 2.0mm ± 0.2mm, corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19mm and 1mm ± 0.1mm wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-in-charge 1 x 7 0.80 2.10 11.76 meter 196.00 2304.96

41 8.15 Providing and fixing factory made 25mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762mm X 25mm or less as per requirement with an average wall thickness of 1mm ± 0.3mm. PVC foam end cap of size 23x10mm are provided on both vertical edges to ensure the overall thickness of 25mm. An M.S. tube having dimensions 19mm x 19mm is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25mm X 11mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufactures' specification. 1 x 7 0.80 2.10 11.76 sqm 2583.00 30376.08

42 9.53 Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side having 12 mm air gap including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. complete.

43 9.34 Providing and fixing stainless wire gauge of average width of aperture 1.56mm with wire of 0.35mm to existing steel door, window shutter frames with necessary M.S. strip beading etc. complete.

44 14.13 Providing and applying 2mm thick ready mix exterior grade approved make putty (like Birla wall care, Alltek Superfine W/R of (NCL), Asian, ICI, Nerolac, J.K. wall putty) on walls to make the surface smooth and even.

Qty of Slab shuttering 489.52

Qty of 12 mm Plaster 974.22

Qty of 15 mm Plaster 1181.26

45 14.9 Distempering with acrylic washable distemper to give an even shade.

Qty of Slab shuttering 489.52

Qty of 12 mm Plaster 974.22

46 14.15 Painting exterior surface with ACRYLIC SMOOTH exterior paint of required shade as per manufacturer's specifications to give protective and decorative finish including cleaning washing of surface etc. complete with:

14.15.1 On new work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Qty of 15 mm Plaster 1181.26 sqm 56.00 66150.56

47 14.22 Painting on new work (two or more coats) to give an even shade with:

48 19.42 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 1 x 2 1000.00 2000.00 Ltr. 7.30 14600.00

49 18.4 Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :

18.4.3 White wall hung type 1 x 1 1 1.00 Each 4415.00 4415.00

50 18.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ), 100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (same colour) conforming to IS : 7231, with flush bend and other fittings and fixtures complete including cutting and making good the walls and floors wherever required :

18.1.3 White Orissa pattern W.C. pan of size 580x440 mm 1 x 1 7 7.00 Each 2899.00 20293.00

51 18.17 Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required :

52 18.25 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

53 18.76 Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete.

54 18.77 Providing and fixing on wall face UV stabilized Unplasticised - PVC Providing and fixing on wall face UV stabilized Unplasticised - PVC PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

18.77.1 Tee/ Tee with door/ Bend 45°/ Bend 90°

18.77.2 Double "Y" with or without door

18.77.3 Vent covel

18.77.5 P trap 110mmx110mm long each 227.00 1 x 1 2 2.00 Each 227.00 454.00

55 19.7 Providing and fixing on wall surface G.I. pipes medium class complete with G.I. fittings and clamps, including cutting, making good the walls etc. and testing of joints complete:

19.7.1 15 mm dia. nominal bore 1 x 1 15 15.00 Rmt 149.00 2235.00

19.7.2 20 mm dia. nominal bore 1 x 1 30 30.00 Rmt 185.00 5550.00

19.7.3 25 mm dia. nominal bore 1 x 1 40 40.00 Rmt 258.00 10320.00

56 19.13 Providing and fixing 15 mm nominal bore Brass bib/stop cock of approved quality:

19.13.3 Stop cock (350 grams) 1 x 1 20 20 Each 237 4740.00

57 19.14 Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:

19.14.4 Piller Cock (400 grams) 1 x 1 10 10 Each 398 3980.00

19.14.14 Soap dish plate 1 x 1 2 2 Each 163 326.00

19.14.16 Towel rail (600mm long x 20mm dia) 1 x 1 7 7 Each 338 2366.00

58 19.15 Providing and fixing stainless steel drain jali of approved make/quality. 1 x 1 10 10 Each 51 510.00

59 18.30.1 Providing and fixing mirror of superior glass (of approved quality) and Providing and fixing mirror of superior glass (of approved quality) and make and shade with 6 mm thick hard board backing : 1 x 7 1.5 0.6 6.3 sqm 2016 12700.80

60 20.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete 150mm thick as per standard design:

20.2.1 100 mm diameter S.W. pipe 1 x 1 15 15 Each 357 5355.00

61 20.25 Providing and constructing brick masonry road gully chamber 50x45x60 cm with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal grating with frame complete as per standard design. 1 x 1 4 4 Each 2872 11488.00

62 20.31 Providing and constructing soak pit 1.20x1.20x1.20m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. 1 x 1 1 1 Each 1709 1709.00

63 9.11 Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm size channels 20x10x2mm and braced with flat iron diagonals 20x5mm size complete with bolts, nuts, locking arrangement stoppers, handles including applying a priming coat of red oxide zinc chromate primer.

Main Gate 1 x 1 2.4 2.4 5.76

Total Rs. 5772866.00

SCHEDULE OF ITEMS FOR INTERNAL ELECTRIFICATION WORK FOR MODEL REGISTRY OFFICE FOR SUB REGISTRAR AT AKALTARA, DISTT.-JANJGIR-CHAMPA (C.G.)

S.NO. SOR ITEM NO. PARTICULARS OF ITEMS UNIT RATE NUMBER IN WORDS (IN RS.)

01 1.7 Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

1.7.1 Short Point Point 235.00 Two hundred thirty-five rupees only

1.7.2 Medium Point Point 374.00 Three hundred seventy-four rupees only

1.7.3 Long Point Point 518.00 Five hundred eighteen rupees only

02 1.9 Extra for providing and fixing light plug point on board in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) point wiring with modular type 3 pin 5/6 amp socket outlet and 5/6 amp switch including cost of base and cover plate and G. I. box etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Point 191.00 One hundred ninety-one rupees only

03 1.10 Wiring for light plug point with 3x2.5 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 6 Amp switch and 3 pin 6 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

1.10.1 Short Point Point 390.00 Three hundred ninety rupees only

1.10.2 Medium Point Point 582.00 Five hundred eighty-two rupees only

1.10.3 Long Point Point 814.00 Eight hundred fourteen rupees only

04 1.11 Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit,along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification.

1.11.3 Long Point Point 1191.00 One thousand one hundred ninety-one rupees only

1.11.4 Extra Long Point-1 Point 1594.00 One thousand five hundred ninety-four rupees only

1.11.5 Extra Long Point-2 Point 2042.00 Two thousand forty-two rupees only

1.11.6 Extra Long Point-3 Point 2492.00 Two thousand four hundred ninety-two rupees only

05 1.13 Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

1.13.2 3 X 2.5 sq. mm in 20mm conduit Meter 98.00 Ninety-eight rupees only

1.13.3 6 X 2.5 sq. mm in 25mm conduit Meter 151.00 One hundred fifty-one rupees only

1.13.4 9 X 2.5 sq. mm in 32mm conduit Meter 210.00 Two hundred Ten rupees only

1.13.6 3 X 4.0 sq. mm in 25mm conduit Meter 128.00 One hundred twenty-eight rupees only

1.13.15 6 X 16 sq. mm in 50mm conduit Meter 681.00 Six hundred eighty one rupees only

06 1.15 Supplying and fixing of following sizes FRLS PVC conduit along with accessories in concealed complete as per specification.

1.15.2 25mm Meter 46.00 Forty-six rupees only

07 3.11 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, multi strand wire in the existing surface/ concealed, FRLS PVC conduit / PVC casing caping as per specification and IS: 694 (2010)

3.11.3 3 x 1.5 sq. mm Metre 32.00 Thirty two rupees only

3.11.11 1 x 2.5 sq. mm Metre 19.00 Nineteen rupees only

3.11.23 3 x 4 sq. mm Metre 72.00 Seventy two rupees only

08 3.13 Supplying and drawing following grade co-axial TV wire FRLS PVC insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ concealed Steel/PVC conduit as per specification

3.13.1 RG-6 grade Meter 12.00 Twelve rupees only

09 3.14 Supplying and drawing UTP 4 pair Cat 6 LAN wire in existing surface/ concealed Steel/FRLS PVC conduit as per specification. Meter 16.00 Sixteen rupees only

10 4.3 Supplying and fixing of following sizes PVC switch box suitable for modular switches with modular base and cover plates on surface complete as per specification

4.3.1 94 mm X 94 mm (1/2 Module) Each 101.00 One hundred one rupees only

11 5.4 Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.

5.4.9 Fan regulator (two module size) electronic stepped type moving all rounds Each 196.00 One hundred ninety-six rupees only

5.4.11 Plug Top (Deluxe type) 3 pin 16 Amps (For power plug). Each 85.00 Eighty five rupees only

5.4.16 T.V. antenna socket outlet Each 65.00 Sixty-five rupees only

5.4.17 Computer Outlet Jack Each 214.00 Two hundred fourteen rupees only

5.4.18 25/32 amp A.C. Starter switch Each 217.00 Two hundred seventeen rupees only

12 5.6 Providing and fixing composite unit for computer points having modular type 1 No 6 pin 16 amp socket outlet, 1 No 16 amp switch, 3 Nos 3 pin 6 amp socket outlets, 3 Nos 6 amp switches, suitable G.I. box, base and cover plates, earthing the sockets and switch box including etc. as per specification. Each 720.00 Seven hundred twenty rupees only

13 5.9 Providing and fixing round/ hexagonal fan box (125mm dia) depth 75mm (max.) with 12mm dia steel bar hook, 1.6mm thick MS sheet cover, in RCC slab etc. as per specification. Each 37.00 Thirty-seven rupees only

14 6.12 Providing and fixing phenolic laminated sheet cover of 180 mm dia 3 mm thick on the fan box etc. as per specification. (If provided at the time of installation of ceiling fan) Each 49.00 Forty-nine rupees only

15 7.17 Providing and making interconnection in cubical panel between BBC and switchgears with following size FRLS PVC insulated copper conductor wire lead of length upto 50cm including providing copper thimbles on both ends as per specification (To be measured separately for each phase/ neutral).

7.17.1 10 sqmm (32 amp) Each 67.00 Sixty-seven rupees only

16 7.19 Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS powder coated sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as per specification.

7.19.1 Upto 300 mm deep sqm 6014.00 Six thousand fourteen rupees only

17 7.21 Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) copper (electric grade) bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as per specification.

7.21.2 200 amp (25x5mm) Metre 2101.00 Two thousand one hundred one rupees only

18 9.1 Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.

9.1.24 4 pole MCCB, 100A, Adjustable Thermal - Magnetic Release, 35KA Each 5626.00 Five thousand six hundred twenty-six rupees only

19 9.2 Supplying and fixing on surface/ recess following way, 240 volts SP&N MCB distribution board of sheet steel phosphatized and powder painted complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, including interconnections, earthing etc. as per specification. (But without MCB/RCCB/Isolator)

9.2.7 12 way, Double door Each 971.00 Nine hundred seventy-one rupees only

20 9.4 Supplying and fixing on surface/ recess horizontal type following way, 415 volts, TPN MCB distribution board of sheet steel phosphatized and powder painted, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, including interconnections, earthing etc. as per specification. (But without MCB/RCCB/Isolator)

9.4.5 6 way Double door Each 1798.00 One thousand seven hundred ninety-eight rupees only

21 9.11 Supplying and fixing SP MCB, 240 volts, 'C' curve, suitablefor inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

9.11.2 6 amps to 32 amps Each 130.00 One hundred thirty rupees only

22 9.12 Supplying and fixing DP MCB, 240 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

9.12.3 40 amps Each 569.00 Five hundred sixty-nine rupees only

23 9.16 Supplying and fixing TP&N MCB, 440 volts, 'C' curve,suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

9.16.5 63 amps Each 1161.00 One thousand one hundred sixty-one rupees only

24 10.17 Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as per specification. Each 83.00 Eighty-three rupees only

25 12.10 Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ concealed conduit/ submain wiring/ cable as per specification. Mtr 46.00 Fourty-six rupees only

26 12.19 Providing maintenance free earthing with following size GI pipe including making bore pit of minimum 150mm dia, providing and laying approved make Earthing Electrode of Pipe-in-Pipe technology as per IS 3043(R 2016) -1987 made of corrosion free G.I. Pipes having outer pipe of 80mm dia and inner pipe of 50mm dia and filling with specified qty highly conductive compound around pipe and above that with soft soil in bore pit complete and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as per specification:

12.19.2 With 2 metre long GI Pipes and 25 kg back filling compound. Each 7253.00 Seven thousand two hundred fifty-three rupees only

27 15.3 Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) & IS: 7098 (1988, Part 1)

15.3.12 3.5 x 35 sq. mm. Metre 118.00 One hundred eighteen rupees only

28 15.23 Supplying and making end termination with brass compression gland andaluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as per specification. .

15.23.13 3½ X 35 sq. mm (28 mm) Each 135.00 One hundred thirty-five rupees only

29 18.9 Supplying and fixing of GI Trunking/Raceways with 120 GSM coating and made up of 1.6 mm thick steel sheet. The steel sheet is Pre Galvanized with zinc coating and is double folded and arc welded in the joints to prevent concrete seepage. The trunking is compartmentalized for provision of data, power and voice cables and has a depth of 25/38mm complete as per specification. : Raw materials complies to Indian Standards IS 277:2003

18.9.11 150 mm x 38 mm x 1.6 mm (2 compartments) Metre 647.00 Six hundred forty-seven rupees only

30 18.12 Supplying and fixing of GI Junction boxes, suitable for 25/38 mm depth GI raceways. The junction boxes are made out of high pressure die cast zinc alloy complete with all accesseries such as trap lid, strong support frame, bore support studs etc. complete as per specification. Trap lid is reinforced and can with stand upto 2 tons of distributed load on the top. As per IEC 61084 Standards

18.12.2 250 mm x 250 mm x 60 mm - 75 mm (1 compartment) Nos. 997.00 Nine hundred ninety-seven rupees only

31 27.28 supplying installation testing and commssioning of 8 port mangable PoE switch 10/100/1000 8 port with 2 giga SFP uplink L2 managed PoE switch power budget max 96 w single port 30 w AI extend AI VLAN As per the specifications Each 7903.00 Seven thousand nine hundred three rupees only

32 27.46 supplying installation testing and commssioning of 9U indoor Rack Wallmount 9U 630D with front glass door lock & key 550 9U-(with 1U cable manager ;fan;6 socket PDU) complete as required Each 3677.00 Three thousand six hundred seventy-seven rupees only

33 27.70 supplying installation testing and commssioning of add on item junction box installed with mount frame inside for krone 10 pair disconnection/disconnection modules ,corrosion free impact resistant ,water proof ,mild steel stable and maintenance free with same size crone module as junction box.

27.70.1 20 pair juction box Each 2594.00 Two thousand five hundred ninety-four rupees only

34 5.7 Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts A.C. supply, complete as per specification.

5.7.2 Deluxe Each 95.00 Ninety-five rupees only

35 6.4 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, including connection, earthing etc. complete as per specification. Each 2349.00 Two thousand three hundred forty-nine rupees only

36 6.5 Supplying and fixing of wall/ cabin fan including connection etc. as per specification. P.F. should be greater than 0.9

6.5.1 300 mm sweep Each 1224.00 One thousand two hundred twenty four rupees only

37 6.6 Supplying, installation, testing and commissioning of following sizes heavy duty (continuous running) 1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9

6.6.1 300 mm sweep Each 2158.00 Two thousand one hundred fifty-eight rupees only

38 6.15 Supplying, installation, testing and commissioning of following LED fitting (luminaries) panel light in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt.

6.15.6 18/20 Watt Each 766.00 Seven hundred sixty six rupees only

39 6.16 Supplying, installation, testing and commissioning of following sleek LED panel down lighters (luminaries) in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and furnishing 5 Yrs Warranty certificate from manufacturer. P.F. should be greater than 0.9. LED chip efficacy ratio ≥100 lumens /watt.

6.16.1 24 watt, size 300 x 300mm Each 1566.00 One thousand five hundred sixty six rupees only

40 6.19 Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt.

6.19.3 18/20 watt {4 feet} Each 390.00 Three hundred ninety rupees only

41 6.27 Supplying, installation, testing and commissioning of following LED Bulk Head fitting complete with Electronic Driver Heat sink Capacitor and all other accessories, including connection, earthing etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. IP65

6.27.1 10 watt Each 1140.00 One thousand one hundred fourty rupees only

42 6.28 Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Separate housing for driver etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.

6.28.7 60 watt Each 3195.00 Three thousand one hundred ninety five rupees only

43 24.3 Supplying of approved make split type Air Conditioner unit with cooling unit (copper coil) and condensing unit (copper coil) including 5 years compressor warranty and standard length of upto 3 metre of copper piping with insulation, etc complete as per specification:

24.3.1 1.5 ton split type capacity 4500 kcal / hr (3 star). Each 29442.00 Twenty-nine thousand four hundred fourty two rupees only

24.3.3 2.0 ton split type capacity 6000 kcal / hr (3 star). Each 42353.00 Forty-two thousand three hundred fifty-three rupees only

44 24.4 Installation of split type Inverter/Non Inverter Air Conditioner unit, cooling unit on wall inside and condensing unit on out side wall/ ceiling/ floor at desired locations with existing standard length of copper piping with insulation and power cable including providing and fixing necessary good quality powder coated MS frame etc complete as per specification. (Extra length of copper piping and power cable shall be paid extra on linear basis) Each 1861.00 One thousand eight hundred sixty-one rupees only

45 24.7 Supply and fixing of approved make wall mounting type voltage stabilizer with input volts 160-250, output volts 200-240 volts and double step relay on desired location with necessary fixing material including connection etc complete as per specification.

24.7.1 4 KVA Each 3381.00 Three thousand three hundred eighty one rupees only

24.7.2 5 KVA Each 3853.00 Three thousand eight hundred fifty-three rupees only

46 24.10 Supply, connecting and fixing extra length of copper piping for split type air conditioners of following dia and approved quality with insulation sleave etc complete as per specification

24.10.1 5/8 " Meter 331.00 Three hundred thirty-one rupees only

24.10.3 1/4 " Meter 165.00 One hundred sixty-five rupees only

47 24.12 Supplying, connecting and fixing 15mm dia PVC flexible drain pipe (reinforced with nylon threads) in drain outlet of split type air conditioners etc complete as per specification Meter 13.00 Thirteen rupees only

48 1.15 Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5)

1.15.1 20 mm Mtr 42.00 Forty-two rupees only

49 3.14 Supplying and drawing UTP 4 pair Cat 6 LAN wire in existing surface/ concealed Steel/FRLS PVC conduit as per specification and IS: 694 (2010) Mtr 16.00 Sixteen rupees only

50 27.11 Supplying, installation, testing and commissioning of 4 MP Bullet Camera weather & dust proof IP based Fixed Lens day/night Camera (IP67, IK 10) , 1/3" 4MP PS CMOS Image Sensor, H.265 and H.264 triple-stream encoding, WDR(120dB), Day/Night Support, UL,CE FCC Certified as per the specifications. Each 5604.00 Five thousand six hundred four rupees only

51 27.18 Supplying, installation, testing and commissioning of 8 Channel NVR 2 Sata port - Up to 16 channel IP camera input , Max 200Mbps incoming bandwidth ,Smart H.265+/H.265/Smart H.264+/H.264 dual codec decoding , Up to 8MP resolution preview and playback , Support 2 SATA HDDs up to 6 TB each, 2 USB(1 USB3.0, 1 USB2.0) , 1 HDMI / 1 VGA simultaneous video output ,ONVIF Version 2.4 conformance , Alarm In / out 4/2 , Two way talk 1 Channel Input, 1 Channel Output RCA , 1 RJ-45 port (10/100/1000Mbps) as per the specifications. Each 9875.00 Nine thousand eight hundred seventy-five rupees only

52 27.28 Supplying, installation, testing and commissioning of 8 Port Managable PoE Switch 10/100/1000 8 Port with 2 Giga SFP uplink, L2 Managed PoE switch, Power Budget max 96 W , single port 30 W ,Al Extend, Al VLAN as per the specifications. Each 7903.00 Seven thousand nine hundred three rupees only

53 27.37 Supplying, installation, testing and commissioning of 4 TB Surveillance Hard disk drive Complete as required. Each 8437.00 Eight thousand four hundred thirty-seven rupees only

54 27.45 Supplying, installation, testing and commissioing of 6U Indoor Rack Wallmount 6U 630D With Front Glass Door Lock & Key 550 4U-(fan +PDU+Cable Manager) etc Complete as per required Nos 3094.00 Three thousand ninety-four rupees only

55 27.49 Supplying, installation, testing and commissioing of following size LED Monitor, table/wall mount with inbuild speaker minimum 5Wx2,with minimum 1 No of HDMI and USB port including remote control, connecting cable, batteries, and all accessories, connection etc complete as per specification.

27.49.2 43 inch Each 38089.00 Thirty eight thousand eighty nine rupees only

56 27.73 Supply, installation and testing for HDMI cable. Metre 408.00 Four hundred eight rupees only

57 11.2 Supplying, installation, testing and commissioning following rating single phase in single phase out ON-LINE UPS including connection etc but without batteries as per specification.

11.2.3 5 KVA with DC bus voltage 180 V Each 41214.00 Forty-one thousand two hundred fourteen rupees only

58 11.5 Supplying, installation, testing and commissioning following rating lead acid battery (Maintenance Type) including connection as per specification.

11.5.3 150 AH Each 12571.00 Twelve thousand five hundred seventy one rupees only

59 20.6 Supplying and erection of angle/channel iron cross arms/ bracket/ other fitting of approved size and shape including drilling of holes for insulator pins, bolts and nuts etc as per specification. kg 68.00 Sixty-eight rupees only