Widening and strengthening Kachanarawa to Bagesoti Jharkhand state Border road including 5 years maintenance upto 2 and half pecent of Construction cost

Excavation for Roadwork in soil with hydraulic excavator of 0.90 cum bucket capacity including cutting and loading in tippers trimming botton and side slopes, in accordance with rrequirements of lines, grades and cross sections and transporting to the embankment location with all lifts and lead upto 5000 m

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300-2

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2.

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site laying in uniform layers with paver in sub base/base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per MORTH specification No.406. in km.

Providing and applying primer coat with SS-2 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means.

Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder (VG-30) @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects.

Providing and applying tack coat with bitumen (VG-10) using bitumen pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder (VG-30) @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects

Excavation in foundation in soil mixed with moorum/ kanker /B.C soil etc. requiring the use of special T&P such as pickaxe, subbals etc. including lift up to 1.50 M and lead up to 30 M complete as per direction of E/I. and as per S.I. No. 252

Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( PCC grade- M 15 )

C.R. with cement and coarse sand mortar in the proportion of 1:4 respectively in foundation & plinth including cost of all material, labour, T&P etc. required for proper completion of the work.

Supply fitting and placing MS bar reinforcement in supperstructure complete as per drawing and techanical specificatin Clauses 1002.

RCC Grade M30 using batching plant transit mixer & manual placing in Super structure.

Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing

Furnishing and Placing Reinforced/ Prestressed cement concrete M-20 grade in foundation as per drawing and Technical Specification. For Drain

Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1,no fragment weighing not less tan 40 kg, laid dry complete as per drawings and technical specifications clauses 1301 .

Raised pointing with cement and fine sand mortar in the proportion of 1:2 respectively over stone masonary including all material, labour, T&P etc. required for proper completion of work. as per S.I. No. 574

Plastering with Cement mortor (1:4) 15mm thick on Stone Works in sub structure as per technical specification clause 613.4&1204 .

Plain/Reinforced Cement Concrete in Sub Structure complete as per Drawing and Technical Specifications.PCC Grade M 20 (Nominal Mix 1:2:4)

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8

PCC Grade M30 using batching plant transit mixer & Concrete pump for Rapta

Providing and Laying 10 cm dia PVC pipes for Weep Holes

Providing weepholes in stone masonry, plain/reinforced concrete abutment, wing wall, ret.wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 as per S.I.No.574

Earth work in embankment / in filling in soil mixed with kanker/moorum etc for diversion i/c lift up to 1.50 M and lead up to 30 M, all labour, T&P etc complete as per direction of E/I. and as per S.I. No. 253.

Supplying, laying, jointing and fixing of 350 mm dia NP3 class hume pipe with collar including its cost and carriage upto site etc complete as per direction of E/I.

Supplying, laying, jointing and fixing of 600 mm dia NP3 class hume pipe with collar including its cost and carriage upto site etc complete as per direction of E/I.

Supplying, laying, jointing and fixing of 900 mm dia NP3 class hume pipe with collar including its cost and carriage upto site etc complete as per direction of E/I.

Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8, fixing in position including painting and printing etc

Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8, fixing in position including painting and printing etc

Providing and Applying Hot applied thermo plastic compound 2.5 mm thick including reflectorising glass beads @ 250 gm /sqm area. Thickness of 2.5 mm is excusive of surface applied glass beads as per IRC 35. The finish surface tu be leveled uniform and free streaks and holes. Composition of thermo plastic material shall be as per table 800-3 of clause 803 of MORTH including cost of all material labour T&P etc required for proper completion of work as directed by E/I.

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 mad of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm

Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m belo

Cantilever signage board Supply,fixing and eraction of built up Cantilever structure 6m span comprising of one vertical post of 6.00m height made up of 300 mm NB heavy class MS pipe as vertical member welded with 10mm MS plate at top and 12mm MS plate at bottom the horizontal truss shall comprise of 50mm dia heavy class MS pipe & 10 mmMS plate at bottom for fixing to vertical post as per structure design & drawing with one of steel primer and two coat of synthetic enemel paint,the work includes construction of RCC foundationof size 90x90 cm of required depth as per site condition for built up structure including earth work in excavation 100 mm thick lean concrete in 1:4:8 and RCC with 1:2:4 including supply and fixing of 25 mm dia foundation bolt 600 mm long as per provision of structure desing including cost of inforcement & shuttering the lateral vertical clearance and complete.Installation work shall be as per relevant clauses of MORT&H specification section 800 and IRC 67 2010 complete in all respect. The rate shall include cost of design,fabrication, supply transportation, local shifting erection of signage structure using crane inclsive of all taxes royalty,VAT etc all T&P machine material and labour for proper completion of work as per direction of E/I

M/s A K Construction Company (BID ID -4823232)

M/s Barhu Singh Kushwaha (BID ID -4814507)

M/S HAZRAT ALI (BID ID -4818212)

V S Y INTERNATIONAL PRIVATE LIMITED (BID ID -4824517)

ASHTBHUJA CONSTRUCTION (BID ID -4823568)

M/s UTSAV ENTERPRISES (BID ID -4817848)