REPAIR/REPLACEMENT OF CERTAIN, CABLES, CAPACITORS BANK, APFC PANELS, STREET LIGHT, LT PANEL, TUBLER POLES JUNCTION BOX AND CONNECTED AT BMC UNDER GE (CENTRAL) KOLKATA

Amount

Demolition of Cement Concrete of any description and in any position not otherwise specifically rovided for complete all as specified and as directed.

Excavation in trenches not exc. 1.5 Metre wide and n exc. 1.50 Metre in depth for laying of cables/foundation of poles and getting out in soft /loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 Cm as in soft/loose soil complete all as specified and directed.

Removing excavated material (soils of any type) not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

Supply and laying dry coarse sand as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 Cm (15 Cm under the cable & 8 Cm over the cable) and gently punned down to 18 Cm thickness complete all as specified and as directed. Note:- Thickness after punning down shall be measured for payment.

Supply and laying in trenches Bricks, sub class 'B' over burnt (kiln burnt) old size bricks, laid flat dry with width of the bricks laid to the axis of the cable for protection of cable complete all as specified and as directed.

Laying only in trenches Old serviceable bricks obtained from taking out old unserviceable XLPE cable, laid flat dry with width of the bricks laid to the axis of the cable for protection of cable complete all as specified and as directed.

M&L for Cutting roads / hard standing to a depth not less than 60 cm and not less than 45 cm wide for laying of GI pipe to draw the UG cable and making good the disturbed surfaces by filling of PCC (1:3:6) type C-2 using 40 mm graded stone aggregate and finished the surface even and smooth with out using extra cement and disposed off the surplus debris and soil to a distance not exc 50 m complete all as specified and as directed.

M&L Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation base of poles and other similar locations complete all as specified and as directed.

M&L Plain cement concrete (1:3:6) type-C-2 using 40mm graded aggregate with and including all necessary form work as in bases of pole complete all as specified and as directed.

M&L Plain cement concrete (1:2:4) type-B-1 using 20mm graded aggregate with and including all necessary form work as in coping of pole complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on other than fair faces of Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and smooth without using Extra Cement complete all as specified and as directed.

Taking out old U/S LT UG cable of any size and any description including GI pipe of any dia fixed with bldg and bricks for cable protection where ever appeared complete all as specified and directed. Note:- (i) Serviceable bricks obtained shall be stacked properly for re-use. (ii) Excavation and earth work shall be measured and paid separately under relevant item of these schedule.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 10 Sqmm 4.0 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 16 Sqmm 4.0 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 25 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 35 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 50 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 70 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 95 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 120 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 150 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 185 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 185 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 240 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 300 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 400 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as specified and directed.

S&F Straight through joint kit heat shrinkable for LT 1100 Volts grade complete with jointing materials and accessories suitable for 3.5/4 core XLPE armoured conductor cable of following sizes including testing of cable after joints complete all as specified and directed. (a) 10 to 35 Sqmm 4.0 core

(b) 50 to 95 Sqmm 3.5 core

(c) 120 to 240 Sqmm 3.5 core

(d) 300 to 400 Sqmm 3.5 core

S&F PVC cable terminal boxes, outdoor type of size 155mm x210mm x92mm with MCB SP 6 to 32 Amps including all necessary fittings and connection including taking down old unserviceable one complete all as specified and directed. Make:- Hansel Model No. KF 1616G or equivalent model from Make:- Sitex/ Universal.

S&F PVC cable terminal boxes, outdoor type of size 93mm x93mm x62mm including fixing with clamp including taking down old unserviceable one complete all as specified and directed. Make:- Hansel Model No. KF 0200B or equivalent model from Make:- Sitex/ Universal.

S&F PVC pole boxes, outdoor type of size 195mm x135mm x90mm IP 65 for pedestrin lighting including fixing with clamp including taking down old unserviceable one complete all as specified and directed. Make:- Sintex Model No. GSJB 2014 or equivalent model from Make:- Hansel/ Universal.

S&F PVC pole boxes, outdoor type of size 250mm x200mm x105mm IP 65 for flood lighting including fixing with clamp including taking down old unserviceable one complete all as specified and directed. Make:- Sintex Model No. GSJB 2520 or equivalent model from Make:- Hansel/ Universal.

S&F Timer switch of Analogue type for street light fittings single phase 250Vof 20 Amp rating including taking down old unserviceable one complete all as specified and as directed. Make:- L&T Cat part No. AUTS01ANA00 or equivalent

S&F LED decorative post top lantern, 40 Watt capacity for energy efficient conservation upto 50% and with eco friendly lighting system with all accessories and necessary connection including taking down old unserviceable one complete all as specified and as directed. Make:- Havells cat part No. RUBYPT35WLED830PSYMTOPC or Surya Cat part No. SLE PT 40W-ETPP or Make:- Bajaj cat part No. BGCL 40W

S&F PVC insulated, stranded copper electric cable, 2.5 Sqmm 2 core drawn into the steel tubular pole by drilling holes above the junction box and another holes near street light bracket including taking out old unserviceable copper wire complete all as specified and as directed.

S&F LED street light luminaries 60 watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver ,lamp bracket with impact and corrosion resistant including thermal mangement in multiple optics with IP 65/66 protection including taking down old unserviceable one complete all as specified and as directed. Make : Bajaj cat no. ENXT P 72L WH CR PC SD or CG model No. LST-60-CDL-M or Surya model no: SLE UL 60W IP66(LXN) or equivalent .

S&F LED street light luminaries 90 watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver ,lamp bracket with impact and corrosion resistant including thermal mangement in multiple optics with IP 65/66 protection including taking down old unserviceable one complete all as specified and as directed. Make : Bajaj cat no. ZELA P 108L WH PO TG SD or CG model No. LSTP-90-CDL-HPM or Surya model no: SLE UL 90W IP66(LXN) or equivalent make of Bajaj/Philips or etc.

M&L Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.00 mm thick burried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI strip 32x6 mm as earthing lead by means of bolts, nuts, check nuts and washers of GI or steel, GI strip proected by 40 mm bore light grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20 mm bore light grade galvanised iron, wire mesh, charcoal or coke common salt laid in alternative layer of 15 cm (complete thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1, 50 mm thick pre-cast RCC (1:2:4) type B-1 normal mix cover slab reinforced with 8 mm dia TMT bar 10 cm c/c bothways and single handle of 10 mm dia round bar including necessary excavation, earth work etc. in soft / loose soil and disposal pf soil to a distance n. exc. 50 m and necessary testing on completion all as shown in electrical plate No. 3 MES Schedule Part-I complete all as specified and as directed. Note-: Excavation to be measured and paid under sch item no- 1 above and PCC will be& paid under sch item no 10 above.contractor its following iteams have not been considered against items no-29 (i0 funnel with watering pipe,wire mesh and copper lugs. (ii) GI protector pipe (iii) Test point

Taking out unserviceable LT Panels/ of any type and size from the site of work complete all as specified and directed by Engineer-in-Charge.

M&L for repair of LT panels/LT feeder piller boxes by carrying out checking thoroughly all electrical connections, lugs busbar, voltmeter, ammeter ,cable glands ,insulator on busbar, and tightening all connections properly with proper size of new nut, bolt, washer as per the site requirements and insulation of busbar with colour code insulation tapes including welding on damage panel and preparation of surfaces internal and external of panels/feeder piller boxes by cleaning with dry cloth /removal dust particles by using air blower and scratching the old painted surfaces as directed and painting with two coats of synthetic enamel paint over a coat of red oxide primer and rewriting existing letters /numbers as directed and repair the existing PCC basement of the feeder piller box/ LT panel as per site requirement or directed including applying one coat of cement base point after preparation of surfaces and testing complete as per direction of Engineer- in- charge. Note:- Cost of PCC, Painting, Nut, bolt, washer etc. are deemed to be included in quoted rates.

Supply, installation testing and commisisioning feeder pillar box CPRI approved of size 1.5 mtrX1.5 mtrX.50mtr outdoor type confirming to IP-54, factory made double door both front and back side, with locking arrangement prewired made out of 3mm thick MS sheet with 04 Nos legs, MS angle iron 40x40x6mm size 0.9mtr long suitable grouted in ground with PCC 1:3:6 type C2 and cement plaster 1:4 including two coats or synthetic enamelled paint over a coat of red oxide primer both internally & externally and including S&F aluminimum bus bar 600 amps rated duly coloured coded 04 Nos and connection through aluminium busbar of suitable size to MCCBs. MCBs and power contactor and accessories fitted in it for incoming and out going cable, including LCD multi function meter for measuring voltage ampere, frequency, KW,KWH,, Phase indicating lamps LED type RYB duly fitted in Panel and all the acessroies to be connected with suitable copper conductor (control wiring) and power connection with busbar, connection of cable with necessary lugs, glands, PVC tape after taking down old unsrviceable feeder pillar box complete all as directed by Engineer-in-Charge. (i) MCCB, 400 Amps, 4 pole, 415 volt,36 KA fixed thermal and magnetic setting - 01 Nos(incoming). (ii) MCCB,250 Amps, 4 pole, 415 volt, 36 KA fixed thermal and magnetic setting - 02 (outgoing) (iii) Changeover 400A steel enclosure type,-01 no, L&T Cat No-SK90480 (iv)Contactor ML-2 , 32A 2NO 2NC- 01 No, L&T Cat no-90701 (v) LCD Multifunction meter with CT -1No (vi) Phase indicating Lamps LED type RYB complete - 01 Set Note-: Drawing shall be submited by the contractor before manufacturing for approval of accepting officer.

S&F MCCB 4 pole 400A, 36KA, 415V thermal and magnetic adjustable type including making all fixing arrangement, cutting welding of existing panel board as per site requirment and painting the disturbed part of panel as per the existing colour of the panel and electric connection including taking down old one complete all as specified and directed .

S&F MCCB 4 pole 250A, 36KA, 415V thermal and magnetic adjustable type including making all fixing arrangement, cutting welding of existing panel board as per site requirment and painting the disturbed part of panel as per the existing colour of the panel and electric connection including taking down old one complete all as specified and directed.

S&F MCCB 4 pole 200A, 36KA, 415V thermal and magnetic adjustable type including making all fixing arrangement, cutting welding of existing panel board as per site requirment and painting the disturbed part of panel as per the existing colour of the panel and electric connection including taking down old one complete all as specified and directed.

S&F MCCB 4 pole 160A, 36KA, 415V thermal and magnetic adjustable type including making all fixing arrangement, cutting welding of existing panel board as per site requirment and painting the disturbed part of panel as per the existing colour of the panel and electric connection including taking down old one complete all as specified and directed.

S&F MCCB 4 pole 100A, 25KA, 415V thermal and magnetic adjustable type including making all fixing arrangement, cutting welding of existing panel board as per site requirment and painting the disturbed part of panel as per the existing colour of the panel and electric connection including taking down old one complete all as specified and directed.

S&F ACB 4 pole 630A, 25KA, 415V with thermal and magnetic release manual fixed type including making all fixing arrangement, cutting welding of existing panel board as per site requirment and painting the disturbed part of panel as per the existing colour of the panel and electric connection including taking down old one complete all as specified and directed.

S&F MCCB 4 pole 32A, 25KA, 415V thermal and magnetic adjustable type including making all fixing arrangement, cutting welding of existing panel board as per site requirment and painting the disturbed part of panel as per the existing colour of the panel and electric connection including taking down old one complete all as specified and directed.

Supply and erecting steel tubular swaged pole complete with cast iron base plate, finial taper plug, bolts, nuts and screw as specified, type 410 SP-31, 9 Metre long including two coats of aluminium paint over one coat of red oxide primer with dismantling of old unserviceable pole and PCC complete all as specified and as directed by the Engr-in-Charge. Note:- Rates quoted shall be deemed to be inclusive of following works:- (a) Material and labour for painting of pole externally with one coat of black bituminous paint (upto planting depth) and above plinth block concrete collar with two coats of aluminium paint over a coat of red oxide primer including preparation of surface. (b) Material and labour for writing letter or figures (Block, Roman, Italic as Indian) with thick synthetic enamelled paint of apprised shade n exc 5 Cm height including numbering of pole all as directed by EIC.

Material and labour Preparation of old painted surface of existing steel tubular swaged pole 9 mtr long, cross arms, clamps, GI street light bracket etc and applying two coats of aluminium paint including writing pole number & bottom of pole painted with black paint with yellow strip around between the junction of aluminium paint and black paint complete all as specified and directed.

Material and labour Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for LT, 20x15Cm size including taking down old unserviceable Danger notice plate complete all as specified and directed.

S&F Aluminium strip 25x3.15mm with saddles and fixing screws etc for roof conductors and down conductors above ground incl taking down old unserviceable one complete all as specified and as directed.

S&F Galvanised iron strip of size 32 x 6 mm with saddles and fixing screws etc buried in ground incl taking down old unserviceable one complete all as specified and as directed.

S&F Air termination aluminium single pointed rod 12 mm dia, 300 mm long as in repair complete all as specified and as directed.

S&F Test point terminal block made of gun metal or phosphorus bronze size 75 x 75 x 25 mm drilled and screwed including 3 nos 8mm dia 25mm long hex head screw as in repair complete all as specified and as directed.

S&F Flexible PVC pipe of size 25mm suitable for electric connection including taking out old unserviceable PVC pipe.complete all as specified and as directed.

Supply and Laying Steel Water Tubing100mm Bore (dia), Galvanised, ‘Light Grade’ with all Fittings, laid in trenches for laying of cable complete as all specified and as directed.

Supply and Laying Steel Water Tubing 80mm Bore (dia), Galvanised, ‘Light Grade’ with all Fittings, aid in trenches for laying of cable complete as all specified and as directed.

Supply and Laying Steel Water Tubing 50mm Bore (dia), Galvanised, ‘Light Grade’ with all Fittings, aid in trenches for laying of cable complete as all specified and as directed.

Supply and Laying Steel Water Tubing 40mm Bore (dia), Galvanised, ‘Light Grade’ with all Fittings, aid in trenches for laying of cable complete as all specified and as directed.

S&F Changeover Switch in sheet steel enclosure, four pole, 200 Amps, Manual type, 415 V after taking down old unserviceable one complete all as specified and as directed.

S&F Changeover Switch in sheet steel enclosure, four pole, 250 Amps, Manual type, 415 V after taking down old unserviceable one complete all as specified and as directed.

S&F Changeover Switch in sheet steel enclosure, four pole, 315 Amps, Manual type, 415 V after taking down old unserviceable one complete all as specified and as directed.

S&F Changeover Switch in sheet steel enclosure, four pole, 400 Amps, Manual type, 415 V after taking down old unserviceable one complete all as specified and as directed.

M&L Glow sign board alongwith 50mm dia GI pipe light grade 3 RMx2 nos duly grouted in ground .80m deep in PCC with accessories and supply and fix with ACP sheet Mild Steel frame box size 20ft x 2.5ft and acrylic raising letter 2 inches with LED module power supply board matching with existing one with board including connection with 1.5 sqmm single core copper conductor cable including all necessary fixing arrangement & tools and plants including taking down old unserviceable glow sign board complete all as directed by Engineer-in-Charge.

Checking connection in power factor correction panel between load services sequences else where located and set in proper condition including renewal of defective devices, testing of capacitor panel obtaining power factor above 0.95 to 0.98 complete using PVC Tape red/yellow/blue and black and cable ties all as directed. NOTE: Renewal of defective components will be measured and paid seperately.

Supply only APFC Relay 12 stage for thyristor/capacitor switching. Make L & T

Supply only 3 pole power heavy duty contactor type MNX 70 coil 230V AC in existing APFC panel . Make- L & T CS97076

Supply only 3 pole power heavy duty contactor type MNX 140 coil 230V AC in existing APFC panel . Make- L & T CS94138

Supply only 3 pole power heavy duty contactor type MNX 50 coil 230V AC in existing APFC panel . Make- L & T CS97075

Supply only capacitor duty contactor type MO C25. Make- L& T Cat No. CS 96322

Supply only capacitor duty contactor type MO C50. Make- L & T Cat No. CS 96324

Supply only 3 pole power heavy duty contactor type MNX 40 coil 230V AC in existing APFC panel . Make- L & T CS94190

Supply only box type heavy duty capacitor 5 kvar type 440V. Make L & T LTBCH 5 kvar

Supply only box type heavy duty capacitor 10 kvar type 440V. Make-L & T LTBCH 10 kvar

Supply only box type heavy duty capacitor 15 kvar type 440V. Make- L & T LTBCH 15 kvar

Supply only box type heavy duty capacitor 20 kvar type 440V. Make L & T LTBCH 20 kvar

Supply only box type heavy duty capacitor 30 kvar type 440V. Make L & T LTBCH 30 kvar

Supply only box type heavy duty capacitor 50 kvar type 440V. Make L & T LTBCH 50 kvar

Supply only LED lamp red/yellow/blue in colour 230V 22.5mm size or as per site complete with connection as directed. Make L&T Cat No. EPLA240

Supply only 16 sqmm copper ring socket with 6mm hole.

Supply only 16 sqmm copper ring socket with 8mm hole.

Supply only copper FRLSH cable 16sqmm flixible conductor.

Supply only 6 sqmm copper frog/ring/pin socket.

Supply only HF Cylindrical HF Fuse 32A 415V AC.

Supply only 6 sqmm copper cable

Supply only MCB chanel as per site requirement

Supply only CT Ratio 200/5. Make- AE/Kappa

Supply only 2 NO /2NC top mounting add on aux contact block. Make L& T CS94114 or equivalent

S&F Driver for street lights , 2x2, spot light, fountain light, any other LED complete all specified and as directed.

S&F Ceiling fans complete with blades, down rods, electronic regulator and acessories 230 V 1200 mm sweep Min air delivery 210 CFM with service Value 6.00 BEE 5 Star rated with brushless direct current motor (BLDC) including taking down old one complete all as directed and specified. Note: Taking down old fan to be deposited to MES store yard.

S&F Exhaust fan AC single phase 240 V of size 300 mm sweep with louver specially designed by toilet/bathroom in domestic ventilattion metal body and blade, powder coated metalic finishes heavy duty motor, protective bird guard complete all as directed and specifed. Make:- VENTLAIR DSP of Havells/CG/Usha or equivalent

S&F Wall fans complete 400mm sweep power input 60 watts, min speed 1350 RPM, Min air delivery 85 CFM, 240V 50 Hz including taking down old one complete all as directed and specified. Note: Taking down old fan to be deposited to MES store yard.

S&F Electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete as directed. NOTE- Old UNSV geysers to be deposited to MES Store.

Yaduvanshi Traders

INDIA ELECTRICAL EQUIPMENTS

Ultimate Solution Company

Globe Electricals

HARSH ENGINEERING

SEN ELECTRIC WORKS