8145/2022-23/E8 PROVN OF CENTRAL HEATING PLANT FOR FIELD HOSPITAL AT TANGTSE UNDER GE 860 EWS

Amount

Surface dressing n.exc 15 cm deep in soft /loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.5M wide and n.exc 1.5M depth and n.exc 10 Sqm on plan and getting out in any kind of soil complete all as specified and directed.

Excavating over areas, n.exc 1.5 m deep and getting out in hard/dense soil complete all as specified and as directed.

Excavating over areas, exc 1.5 m deep and n, exc 3.00 m deep getting out in hard/dense soil complete all as specified and as directed.

M & L for PCC 1:4:8 type D-2 ( Nominal mix) using 40 mm graded crushed stone aggregate as in foundation filling and similar work complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete etc complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished square,flat, rectangular or polygonal surfaces of concrete complete all as specified and directed.

M&L for formwork to sides of concrete roof beam, LBs sides and soffits (if any) of similar work; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for formwork to soffits of suspedded slabs such as roof slabs, floor slabs landings and similar work ,vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for rough finished formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed by Engr in Charge

M&L TMT bars 10mm dia and over in reinforcement cut to length bent to shape required incl hooking ends and binding with MS wire (annealed) not less than 0.9mm dia all as directed and specified.

M&L TMT bars 6 to 8mm dia and over in reinforcement cut to length bent to shape required incl hooking ends and binding with MS wire (annealed) not less than 0.9mm dia all as directed and specified.

TMT bars for reinforcement 5mm to 10mm dia as in stirrups/spacers/binders etc. cut to length bent to shape required including bending cranking and hooking ends and binding with including MS wire not less than 0.9mm(annealed) dia complete all as specified.

M & L for providing RCC M- 25 (using 20 mm graded crushed stone aggregate) in foundations, including rafts,footings, foundation beams, plinth beams, bases of columns and similar work complete all as specified and as directed.

M & L for providing RCC M- 25 (using 20 mm graded crushed stone aggregate) in columns, pillars, piers, post and struts etc complete all as specified and as directed.

M & L for providing RCC M- 25 (using 20 mm graded crushed stone aggregate) in Beams, cantilevers,and lintels and chajja etc complete all as specified and as directed.

M & L for providing RCC M- 25 (using 20 mm graded crushed stone aggregate) in Slab supported in walls beams and columns in roof ,Landing, balconies, deck slabs and in shelves and similar work complete all as specified and as directed.

M&L for walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as specified and as directed.

M&L for walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, laid dry complete all as specified and as directed.

Returning filling in incl spreading leveling, watering, and well, ramming in layer nexc 25 cm in layers complete all as specified.

Removing excavated material to a distance n. exc50 m and depositing where directed at a level n. exc 1.50 m above the starting point complete all as specified.

M & L Precast cement concrete block masonry type C1 1:3:6 (20mm graded crushed stone aggregate) with solid blocks, exc. 10cm in width and, setting in cement mortar 1:6 complete all as Specified.

M&L for Rendering 10mm thick in cement mortar 1:6 on PCC block walling or concrete surfaces, finished even and smooth without using extra cement complete.

M&L for Rendering 15mm thick, in cement mortar 1:4 on PCC block walling or concrete surfaces and finished even and fair without using extra cement complete.

M&L for Rendering 5mm thick in cement mortar 1:3 on ceiling surface, finished even and smooth without using extra cement complete.

M&L Hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface in broken stone or boulders complete all as specified and directed.

M&L for Cement Concrete type C-2, 1:3:6 (20 mm graded crushed stone aggregate) - 100mm thick as Sub base complete all as specified and directed.

M&L for coloured jointless Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm screed bed in cement mortar 1:6 complete all as specified and directed by Engr -in-Charge

M&L for Glazed ceramic tiles 450x300x7mm thick coloured/shaded as in vertical surfaces such as skirting dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the surface

M&L for preparation of new plastered surfaces and apply two coats of cement base paint complete all as specified and directed.

M&L for preparation surface and apply two coats of oil bond distemper over a coat of primer on newly plastered surface complete all as specified and directed.

M&L for preparation surface and apply three coats of white wash on newly plastered surface complete all as specified and directed.

Supply only water proofing compound for external plaster complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C1 (using 20mm graded crushed stone aggregate) as in plinth protection complete all as specified and directed

S&F in repair vitreous china squatting Pan of Orrisa pattern 580 mm x 440 mm with integral foot rest white with CI "P" or "S" trap front or back inlet including PCC bedding complete all as specified and directed

S & F of 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed..

M&L Concrete bed 1:4:8 type D-2 to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested bore of pipe in 110mm complete all as specified and as directed.

S&F 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches complete all as specified.

S&F 500 ltr cap Rotational moulded polyethylene water storage tank triple layered (cylindrical vertical with threaded closed top) hoisted and fixed in position including all accessories all as specified and directed by Engr-in-Charge

S&F PVC floor trap 75 mm bore with grating setting and jointing with solvent cement complete all as specified and directed

M&L for PVC (SWR) 110 mm gully trap setting joining with solvent cement complete all as specified and directed.

S&F 20 mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F 20 mm bore ball valves high pressure PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed.

S&F of 16mm bore 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc

All as per item No 44 here-in-before but 20 mm dia pipe

S&F 15 mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe and fixed.

S&F 20 mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F Viterous China wash hand basin with pedestal coloured, flat back of 550 x 400 mm including brackets, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia, PVC flexible waste pipe of 750mm long complete all as specified and directed

S&F 15mm bore pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified

S&F of 15mm bib taps, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed

S&F PVC connection 15mm size with PTMT nuts of length 450mm fixed complete all as specified and directed.

OIL FIRED BOILER :Supply, installation, testing and commissioning of oil fired glycol based hot water generator (boiler) using Kersoen/HSD oil complete with combustion chamber and equipment automatic monoblock burner assembly tubes, control panel with sequence controller, blower assembly, electric panel, mounting frame, pressure gauges at inlet and outlet suitable for operation on 50 Hz, 3 phase 415 volts AC supply and all as specified (01 Nos working and 01 No as standby.) Hot water inlet temp=65°C Hot water outlet temp=75°C Capacity-1,00,000 Kcal/hr at 303 FD Hospital Make : Rapidcool/Thermax/Rapidtherm/Western

GLYCOL MAKE UP CENTRIFUGAL PUMP OF 1 HP: Supply, installation, testing and commission of monoblock centriugal pump with bronze impeller, and carbon steel shaft , driven by suitable capacity electric motor for glycol fluid makeup and mixing complete with accessories including cement concrete foundation in PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) incliding required wiring with suitable gauge electric wire in steel conduit all as directed. Make : Kirloskar/CG/Havells

GLYCOL CIRCULATION CENTRIFUGAL PUMP of 3 HP : Supply, installation, testing and commission of monoblock centriugal pump driven by suitable capacity electric motor for ethylene glycol of 3 HP capacity inclcement concrete foundation in PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) all as specified. Make : Kirloskar/CG/Havells

FAN COIL UNITS OF 2 TR : Supplying, installing, testing and commissioning of wall/ floor mounted fan coil units complete with top grill, side panels, copper tube aluminium finned coil centriugal fan finished with powder coated paint for superior finish of cabinet and incl 3 pin 15 Amps plug top and remote with 2 nos battery all as per manufacturers specification. . Make Western/Godrej/Voltas

Supply and lay & testing of M S Pipes heavy grade with all fittings laid in floors or fixed to walls and ceilings of following sizes complete all as specified and as directed by Engr-in-charge

20mm bore MS pipe

25mm bore MS pipe

32mm bore MS pipe

40mm bore MS pipe

50mm bore MS pipe

65mm bore MS pipe

80mm bore MS pipe

100mm bore MS pipe

M & L for Insulation of M S Pipe with PUF slab 40 mm thick with and including applying bituminuous compound and GI cladding with 26 gauge GI sheet complete all as specified and as directed by Engr-in-charge.

20mm bore MS pipe

25mm bore MS pipe

32mm bore MS pipe

40mm bore MS pipe

50mm bore MS pipe

65mm bore MS pipe

80mm bore MS pipe

100mm bore MS pipe

Supply and fixing gun metal, globe or gate valve for pipe with iron wheel head, screwed both ends ISI marked of following sizes complete all as specified (Make : Kirloskar / Sant / BIR /Jindal or equivalent approved make)

20 mm bore dia of pipe

25 mm bore dia of pipe

32 mm bore dia of pipe

40 mm bore dia of pipe

50 mm bore dia of pipe

FUEL GAS CHIMNEY : Supply and installation testing and commissioning of flue gas chimney suitable for above boiler fabricated from MS plate of thickness not less than 6 mm with necessary glass wool insulation and Almunium cladding (SWG-26) complete with boiler connections complete all as specified

Supply and fixing Pressure guagues with cocks and syphon complete all as specified

Supply and fixing Temperature guague complete all as specified

Supply and fixing Y stainer 50mm complete all as specified

Supply and fixing auto air vent valve of brass 25mm dia complete all as specified

Supply and fixing NRC stainer 40 mm dia of brass complete all as specified

S&F for 1000 ltrs capacity rotational moulded polyethylene water storage tank triple layered (cylindrical vertical with threaded closed top) hoisted and fixed in position all as specified in SSR Part I including all accessories complete all as specified and directed by Engr-in-Charge.

Supply and fixing Cast iron gun metal butterfly valve of size 100 mm dia with CI drilled flanged ends (integrally cast) class PN-I.6, conforming to IS : 13095 / BS: 5155 with stainless steel spindle and iron wheel non rising type including jointing material complete such as rubber or fibre board insertion packing rings with requisite numbers of nuts, bolts & washers etc complete all as specified and directed. Make : KIRLOSKAR/BIR/LEADER

Supply and fixing Cast iron gun metal butterfly valve of size 80 mm dia with CI drilled flanged ends (integrally cast) class PN-I.6, conforming to IS : 13095 / BS: 5155 with stainless steel spindle and iron wheel non rising type including jointing material complete such as rubber or fibre board insertion packing rings with requisite numbers of nuts, bolts & washers etc complete all as specified and directed. Make : KIRLOSKAR/BIR/LEADER

Supply and fixing Cast iron gun metal butterfly valve of size 65 mm dia with CI drilled flanged ends (integrally cast) class PN-I.6, conforming to IS : 13095 / BS: 5155 with stainless steel spindle and iron wheel non rising type including jointing material complete such as rubber or fibre board insertion packing rings with requisite numbers of nuts, bolts & washers etc complete all as specified and directed. Make : KIRLOSKAR/BIR/LEADER

Supply and fixing Cast iron gun metal butterfly valve of size 50 mm dia with CI drilled flanged ends (integrally cast) class PN-I.6, conforming to IS : 13095 / BS: 5155 with stainless steel spindle and iron wheel non rising type including jointing material complete such as rubber or fibre board insertion packing rings with requisite numbers of nuts, bolts & washers etc complete all as specified and directed. Make : KIRLOSKAR/BIR/LEADER

Supply, mixing and filling of mono Glycol concentrate along with necessary additives and inhibitor in cognition and sealed in barells. The mixture freezing temperature shall be (-) 35 degree Centigrade , all as specified . The mode of payment and operation involved for this item shall be as under:- Note: (a) Mono Ethylene Glycol in concentrated from shall only be measured and paid under this item. (b) M & L for mixing, filling, preparation for Glycol charge to get the total quantity of mixture including first filling required for operation of CHS plant and network having 40% quantity of treated water available at site and 60% of mono ethylene glycol supplied as above to attain the freezing temperature of mixtures as (-35 degree Centigrade). The quoted rates shall be deemed to include the above provision. (c) The water for preparation of mixture will be supplied by MES without any extra charges for this item. The water shall be supplied at appoint decided by GE and quoted rates shall deemed to be included for transportation of same from the take off point . (d) Any other additives and inhibitors as per the requirement laid down in relevant IS shall also deemed to included in quoted rates. (e) Empty barells shall be property of MES. Make :- Indian oil/Hindustan petroleum/ Bharat petroleum

Material and labour for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified

Supply and fixing of slotted cable tray made out of 4mm thick MS sheet 350mm wide for all boiler, pumps (to carry cable connection to mentioned electrical equipments) all as specified and as directed by Engr-in-charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m depth for laying of cable/ stay assy/LT poles and getting out in hard/dense soil complete all as specified and directed.

Sand cushioning to underground cable complete all as specified in clause 19.75 of SSR Part - I.

Material and labour for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick complete all as specified.

Supply and fixing tube medium grade galvanized with all fitting and fixed complete to walls/ poles/ ceiling or laid in floor of size 50 mm bore for the protection of UG cables including dismantling/ taking out old, unserviceable one complete all as specified and as directed.

Material and Labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross sectional area 25Sqmm 4 Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed.

M/S TRADE LINK

M/S Behl Sons