Loading
Loading…
Loading…
Tender ID
Tender Value
Refer Docs
EMD Value
₹9,980
Closing Date
28 Mar 2026, 2:00 pmClosed
EXECUTIVE ENGINEER (WATER SUPPLY) GRWW
OFFICE OF THE EXECUTIVE ENGINEER (WATER SUPPLY) GARDEN REACH WATER WORKS, BIDHANGARH, KOL-66
RENOVATION OF DAMAGED ROTATING ASSEMBLY OF PUMP UNIT NO. 3 ALONG WITH REPLACEMENT, FITTING-FIXING, TESTING AND COMMISSIONING OF THE SAME AT CWPS-II, GRWW.
2026_KMC_1022229_1
KMC/EE/WS/GRWW/25-26/PH-II/55
Open Tender
MECHANICAL
Item Rate
15 days
CWPS-II OF GARDEN REACH WATER WORKS
Please refer Tender documents.
4 documents required · 4 mandatory
₹0
₹9,980
12 Jun 2026
13 Mar 2026
30 Mar 2026
13 Mar 2026
28 Mar 2026
13 Mar 2026
DISMANTLING OF NUT & BOLT WASHER ETC OF TOP COVER FROM LOWER HALF CASING OF PUMP AND KEPT IT SUITABLE PLACE AS PER DIRECTION OF THE EIC.
DISMANTLING THE BEARING HOUSING AT BOTH END & DECOUPLING BOTH FROM PUMP MOTOR UNIT AND LIFTING THE TOTAL ROTATING ASSEMBLY & KEEP IT AT A SUITABLE PLACE AS PER DIRECTION OF THE EIC.
DISMANTLING THE ALL PART OF THE ROTATING ASSEMBLY ONE BY ONE SUCH AS COUPLING UNIT OF PUMP SIDE & BEARING, SLEEVE, SLEEVE NUT AT BOTH END ETC.INCLUDING TO AND FRO TRANSPORTATION, LOADING, UNLOADING ETC. AS PER DIRECTION OF THE EIC.
SUPPLY, DELIVERY AND FITTING-FIXING ALONG WITH NECESSARY MACHINING & FINISHING OF SHAFT SLEEVE MADE OF SS 410 IN RESPECT OF THE ROTATING ASSEMBLY AS PER SAMPLE AND DIRECTION OF THE EIC.
SUPPLY, DELIVERY AND FITTING-FIXING ALONG WITH NECESSARY MACHINING & FINISHING OF BUSH FOR COUPLING OF PUMP-MOTOR MADE OF NEOPRENE RUBBER IN RESPECT OF THE ROTATING ASSEMBLY AS PER SAMPLE AND DIRECTION OF EIC.
SUPPLY, DELIVERY AND FITTING-FIXING ALONG WITH NECESSARY MACHINING & FINISHING OF COUPLING BOLT WITH NUT MADE OF HT STEEL IN RESPECT OF THE ROTATING ASSEMBLY AS PER SAMPLE AND DIRECTION OF EIC.
SUPPLY, DELIVERY AND FITTING-FIXING ALONG WITH NECESSARY MACHINING & FINISHING OF NUT, BOLT & WASHER FOR TOP & BOTTOM CASING MADE OF HT STEEL AS PER SAMPLE AND DIRECTION OF EIC.
Supply and delivery of the following bearing (Make: SKF):NU322ECM
SUPPLY, DELIVERY, FITTING AND FIXING OF SKF MAKE BEARING NO 7322 BECBM FOR 24UPH3 PUMP AT CWPS-II, GRWW.
SUPPLY, DELIVERY AND FITTING-FIXING ALONG WITH NECESSARY MACHINING & FINISHING OF SLEEVE NUT/JAM NUT MADE OF SS 410 IN RESPECT OF THE ROTATING ASSEMBLY AS PER SAMPLE AND DIRECTION OF EIC.
SUPPLY, DELIVERY AND FITTING-FIXING ALONG WITH NECESSARY MACHINING & FINISHING OF IMPELLER WEAR RING MADE OF CF8M IN RESPECT OF THE ROTATING ASSEMBLY AS PER SAMPLE AND DIRECTION OF THE EIC.
DYNAMIC BALANCING OF THE ROTATING ASSEBLY OF THE PUMP INCLUDING TO & FRO TRANSPORTATION, LOADING-UNLOADING ETC AS PER DIRECTION OF THE EIC AND SUBMISSION OF NECESSARY CERTIFICATE BY A REGISTERED AGENCY/SHOP.
LOWERING TOTAL ROTATING ASSEMBLY OF THE PUMP AND PLACING IN PROPER POSITION ON TO THE BOTTOM CASING OF THE PUMP
PLACING THE TOP COVER OF THE PUMP IN PROPER POSITION ON THE BOTTOM CASING & TIGHTENING THE NUT BOLTS AT THE JOINING POINT OF TOP & BOTTOM CASING & FITTING THE BEARING HOUSING & GLAND UNIT AT BOTH END AS PER DIRECTION OF EIC.
COMMISSIONING OF THE COMPLETE PUMP UNIT INCLUDING PROPER ALIGNMENT OF THE MOTOR WITH RESPECT TO THE PUMPING UINIT AND COUPLING OF PUMP AND MOTOR UPTO THE SATISFACTION OF THE EIC.
TRIAL RUN OF THE PUMP ASSEMBLY FOR A PERIOD OF 24 HRS TO THE SATISFACTION OF THE EIC.
stage.html
html • 0.02 MB
cancelled_1.pdf
pdf • 0.04 MB
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 1.04 MB
OID.pdf
Additional Documents • 0.43 MB
BOQ_2512385.xls
BOQ • 0.34 MB
TechnicalBid55.pdf
Tender Documents • 0.43 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .