SPECIAL REPAIR TO BLDG NO. B-22, PROVN OF MEDICAL STORE ROOM AT BLDG NO. B-22 AT MDC, PROVN OF HARDSTANDING AND MOSQUITO PROOFING AROUND STATION BADMINTOM COURT INSIDE DODA RESIDENCIAL COMPLEX, PROVN OF ENTRANCE SHED WITH INTERLOCKING TILES IN FRONT

Amount

SCHEDULE 'A' PART-I (B/R WORK) Demolition of cement concrete (unreinforced) as in ground floors or paving not exc. 15cm thick below or above ground level complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specially provided for complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlars facing dressed stonework & precast concrete articles complete all as specified and directed.

Taking down cement plaster of any description on brick or stone or concrete surface of wall etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Taking down of shutter of any description not exceeding 1 Sqm each complete all as specified and directed.

Taking down chowkats or frame wooden / PVC/Aluminium (without taking off shutter from the frames) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frame wooden / PVC/Aluminium (without taking off shutter from the frames) exceeding 1.50 Sqm but not exceeding 4.0Sqm each complete all as specified and directed.

Taking down chowkats or frame wooden / PVC/Aluminium (without taking off shutter from the frames) not exceeding 1.50 Sqm each and refixing the same after easing, screwing, etc. for smooth functioning of door complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi-corrugated etc.) sheets in roof coverings complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed.

Excavating in post holes (or similar holes) in soft /loose soil each not exceeding 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good the surface complete all as specified and directed.

Surface excavation in soft /loose soil not exceeding 30cm deep and averaging 15 cm deep and getting out complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for foundation or for shafts, well, cesspits, pier holes etc not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in soft/loose soil complete all as specified and directed.

Removing surplus excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting points in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading leveling, watering and well ramming in layers not exceeding 25cm, soil complete all as specified and directed.

M&L for broken stone or boulders hardcore of gauge not exceeding 63mm, deposited spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for broken bricks hardcore of gauge exceeding 63mm but not exceeding 100mm deposited spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for PCC (1:2:4) type B-2 (using 40 mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in fixing hold fast, coping, bed plates, kerbs or mud stops, top of chajjas, basement for water tank etc rounded or chamfered on edges including necessary form work finishing the surface even and fair with using extra cement complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in roof kerbs or mud stops, top of chajjas, coping, bed plates, basement for water tank etc rounded or chamfered on edges including necessary form work finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for precast reinforced cement concrete (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in cover slab of drain/manhole, landings cover slab for manhole, chullah hoods, chajjas, water through, managers, shelves and similar articles set in cement mortar (1:4) complete all as specified and directed. (NOTE: Cost of Form Work is deemed to be inclusive of unit rate quoted by the contractor and reinforcement shall be measured and paid Separately.)

M&L for RCC (nominal mix) (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in foundations including rafts, footings, foundation beam, plinth beams, bases for columns etc , basement slabs, under-reamed piles and mass concrete etc complete all as specified and directed.

M&L for RCC (nominal mix) (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in column, pillar, piers, post and struts etc complete all as specified and directed.

M&L for RCC (nominal mix) (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

M&L for RCC (nominal mix) (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) used as in slab supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves and like etc complete all as specified and directed.

Cutting holes into or through brick walls built in cement mortar or stone walls to a depth of embedded portion exc one brick thick but not exc. two brick for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 (using 20mm graded crushed stone aggregate) complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching for 150mm dia of pipe complete all as specified and directed.

M&L for cutting chases, in brick wall, pinning in and making good to facing where required and pointing in cement mortar (1:3), to ends or edges of landing, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing etc and making good the disturbed surface, cutting not exceeding 10 cm girth complete all as specified and directed.

M&L for brick work with sub class 'B' bricks locally available best quality straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:4) complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks locally available best quality , straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed.

Supply only integral water proofing compound liquid, ISI marked complete all as specified and directed.

Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work in cement mortar (1:6) complete all as specified and directed.

Providing form work to sides of concrete foundation, footing, base of column, raft & plinth beam for flat, rough finish surface of concrete complete all as specified and directed.

Providing form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc for flat, rough finish surface of concrete complete all as specified and directed.

Providing form work to sides of pillar, posts, struts, piers, columns and stanchions for flat, rough finish surface of concrete complete all as specified and directed.

Providing formwork to the soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200 mm thick (horizontal or sloping ) and making flat, rough finished surfaces of concrete complete all as specified and directed

Providing formwork to Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail?ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon?tal or sloping and similar work exc 10cm but n exc 20cm wide rough finished surfaces of concrete complete all as specified and directed.

Material and labour for 12mm thick medium density fibre board, exterior grade, fixed with screws/ beading to aluminium frame complete all as specified and as directed.

S&F of factory made solid PVC door frame of size 50mm X 47mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube as per specification and drawing as mentioned in SSR Part-II (2020), Section 8, Page No. 178 complete all as specified and directed.

S&F of factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification & drawing as mentioned in SSR Part-II (2020), Section 8, Page No.174 complete all as specified and directed.

S&F of 35mm thick second class hard wood glazed/ gauge & skeleton shutters , open rebated & prepared to receive glass, gauge etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitered beads for securing glass etc. sizes of members of shutters as specified in SSR part-I, Section-8, Clause 8.24 (a) (larger size to be provided) complete all as specified and directed.

S&F of 35mm thick (factory made) plain, second class hard wood, framed, panelled shutters (three panels) with lock rails and panel of 12 mm veneered particle board with commercial veneering on both faces (BWR type), the size of rail and stile as per IS-1003 (Part-I) (larger size to be provided) klin seasoned and chemically pressure treated fitted to chowkats complete all as specified and directed.

S&F in repairs of double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel (heavy duty) complete all as specified and directed.

S&F of double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel (heavy duty) complete all as specified and directed.

S&F in repairs of aluminium extuded body door closer hydraulically regulated designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg as fixed complete all as specified and directed.

S&F of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor (overall length of cover plate 150mm) complete all as specified and directed.

S&F in repairs of 250 mm aluminum alloy, anodised , sliding door bolt with hasp and staple (bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified and directed.

S&F of 300 mm aluminum alloy, anodised , sliding door bolt with hasp and staple (bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified and directed.

S&F of 200 mm long aluminium, anodised, barrel tower bolts of extruded section( IS-204 (Part-2) : 1992) and fixed complete all as specified and directed.

S&F of 150 mm long aluminium, anodised, barrel tower bolts of extruded section( IS-204 (Part-2) : 1992) and fixed complete all as specified and directed.

S&F of 150 mm long aluminium anodised extruded alloy handle fabricated type(IS-208: 1996) complete all as specified and directed.

S&F of 100 mm long cold rolled mild steel butt hinges, medium weight complete all as specified and directed.

S&F of 100 mm mortice lock vertical type of brass with 4 lever completed all as specified and directed.

S&F in repairs of 25mm dia aluminium, powder coated (wood colour finished), single curtain rails (wall thickness of curtain rails not less than 1mm) including funnels etc complete all as specified and directed.

S&F of MS bracket (heavy duty), powder coated of best quality as approved by GE suitable for fixing 25mm bore curtain rails fixed in wall complete all as specified and directed.

S&F of stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm & fixed with stainless steel wire staple complete all as specified and directed.

S&F of anodised (powder coating of minimum thickness 50 micron) aluminum frame (powder coated) for doors , windows, ventilators with one or more rebates (sliding & fixed type) including jointing cleat for fixing etc complete all as specified and directed.

S&F for anodised (powder coating of minimum thickness 50 micron) aluminium door shutters (powder coated), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. including locking arrangement, roller complete all as specified and directed.

S&F of anodised (powder coating of minimum thickness 50 micron) aluminium window/ventilators shutters, double leaf type without sash bar, aluminum section weighing 0.55 Kg/m, including necessary joining cleat, glazing clips, rubber neoprene packing, hinges type B-21 100 mm long (02 Nos), peg stay 150mm long (01 No), anodised aluminium snap beading, screws etc including locking arrangement, roller complete all as specified and directed.

M&L for TMT bars 10 mm dia and over cut to length bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F of rolled mild steel angle iron roof trusses (framed) and purlins, rafters crane gantries, rails, heavy brackets etc including distance pieces, cleats, angle, tee etc including necessary cutting , welding etc complete Fe-410W (Gde E-250) quality 'A' complete all as specified and directed.

S&F of mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or forged into spikes; framed guard bars; barred iron doors; ladders, railings, framed brackets, walk ways, frame work of water tank and similar work conforming to Fe-290-0 Gde-E-165 complete all as specified and directed.

S&F for Welded steel wire fabric supplied and fixed complete to wood or steel members weight per Sqm not exceeding 4.00Kg complete all as specified and directed.

S&F of mild steel hold fast of made flate iron of size not less than 25mm x 6mm complete all as specified and directed.

S & F of framed brackets of angles or tees with web and flanges cut to shape, drilled and counter sunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F of pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F of pre-painted galvalume aluminium zinc coating GI based plain steel sheet of 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in ridge / wall/cladding, fixed with self tapping screws complete all as specified and directed.

S & F for 605mm X 605mm grid GI frame work for seamless false ceiling compising of GI perimeter channel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm eachn and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including 12mm Gyspsum Board in ceiling fixed with screw as per manufacturers instructions for insulation/acoustic purpose of 600mm x 600mm in size fixed with snap grid flase ceiling frame and 0.55mm thickness having jurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with conccecting clips across the intermediate channel at 457mm centre to centre and Hangers 6mm dia GI (upto 1200mm length) adusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-2 (using 20mm graded crushed stone aggregate), as in sub base to footpath and floor complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8) type D2 (using 40mm graded crushed stone aggregate), as in sub base of floor complete all as specified and directed.

M&L for 100mm thick PCC (1:4:8) type D2 (using 40mm graded crushed stone aggregate), as in sub base to footpath and floor complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in plinth protection & floor including finishing the cement concrete surface even and smooth without using extra cement complete all as specified and directed.

M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound of grade 'A' complete all as specified and directed.

M&L for 25 mm thick cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in floor/paving etc finished even and smooth without using extra cement complete all as specified and directed.

M&L for 20 mm thick screed bed in cement mortar 1:4 on concrete surfaces of roof as levelling course mixed with WPC @200ml per 50 Kg of cement or as per manufacturer's instructions complete all as specified and directed. (Note : WPC will be measured and paid separately under relevant item)

M&L for 50 mm thick cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in floor/paving etc finished even and fair complete all as specified and directed.

M&L for vitrified light shade (shade as approved) ceramic tiles (ultra charge) 8-10mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 Sqm in floors etc set over and including 15mm screed bed in cement mortar (1:4) and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

M&L for non skid (joint free) ceramic coloured tiles of 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match with shed of tiles over and including 15mm thick screed bed or beading layer of cement mortar (1:4) for laying floor finishes complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface of size 450 mmX 300 mmX 7 mm to 8mm thick or equivalent set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering of cement mortar (1:4) complete all as specified and directed.

M&L for 20mm thick granite (any type) work (table rubbed and polished) machine cut in steps, jambs, pillars, window cill, cooking platform etc bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the granite stone including and polishing over and including 15mm thick cement mortar (1:4) as screed bed complete all as specified and directed.

M&L for 60mm thick machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2008 (M-35 grade) laying over and including 50mm thick sand filling complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on brick work or concrete surfaces of wall, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:3) on brick work or concrete surfaces of ceiling, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster on concrete surface on top of RCC roof with cement mortar (1:4) mixed with WPC @200ml per 50 Kg of cement or as per manufacturer's instructions , finished the surfaces even and smooth without using extra cement complete all as specified and directed. (Note : WPC will be measured and paid separately under relevant item)

M&L for applying two coats of oil emulsion distemper over a coat of alkali resistant primer over and including applying 3 mm thick wall care putty on wall after preparation of newly plastered surfaces of walls complete all as specified and directed.

M&L for applying two coats of oil emulsion distemper over a coat of alkali resistant primer over and including applying 3 mm thick wall care putty on ceiling surfaces after preparation of newly plastered surfaces of walls complete all as specified and directed.

M&L for applying two coats of oil emulsion distemper over a coat of alkali resistant primer over and including applying 3mm thick wall care putty on old decorated plastered surface of wall after and including complete removal of existing treatment and preparation of surfaces complete all as specified and directed.

M&L for applying two coats of acrylic exterior emulsion paint over a coat of exterior acrilic primer over and including applying 3mm thick wall care putty on old decorated plastered surface of wall after complete removal of existing treatment including preparation of old plastered surfaces complete all as specified and directed.

M&L for applying two coats of acrylic exterior emulsion paint over a coat of exterior acrilic primer over and including applying 3mm thick wall care putty on new plastered surface of wall including preparation of plastered surfaces complete all as specified and directed.

M&L for applying three coats of white wash on surface of ceiling including preparation of new plastered surface complete all as specified and directed.

M&L for applying two coats of cement based paint over a coat of alkali resistance primer on newly plastered surface of walls including preparation of surface complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer after preparation of new steel surfaces of any description over 10cm width or girth complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer after complete removal of existing paint including preparation of old steel surfaces of any description over 10cm width or girth complete all as specified and directed.

M&L for writing letters or figures (block, roman, italic or Indian) not exceeding 30cm high after cleaning and preparation of existing surfaces complete all as specified and directed.

M&L for writing stops, commas, short lines dashes, hyphens, bracket etc after cleaning the existing surface complete all as specified and directed.

M&L for preparation of wood and wood based/ steel based materials treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc., area n exc 0.1 sq. m each complete all as specified and as directed.

S&F of 3mm thick figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 sqm each pane complete all as specified and directed.

S&F of 5.5mm thick sheet glass ordinary quality and glazing with oil putty or fixed with aluminium bead/glazing pins in squares not exceeding 0.50 sqm each pane complete all as specified and directed.

S&F of 5.5mm thick sheet glass ordinary quality and glazing with oil putty or fixed with aluminium bead/glazing pins in squares exceeding 0.50 sqm each pane complete all as specified and directed.

S&F in repairs of 15mm dia bib tap, fancy type, cast copper alloy with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferule, chromium plated with long screw type fixed complete all as specified and directed.

S&F in repairs of central hole CP wash basin mixer for mixing Hot & Cold water screw down for iron pipe including necessary connection pipe from stop cock complete all as specified and directed.

S&F in repair of chromium plated Towel rack 600mm long with lower hangers complete all as specified and directed by Engr-in-Charge.

S&F in repairs of 15 mm bore angular stop valve, fancy type, chromium plated , cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs of 15 mm bore stop valve, fancy type chromium plated with long shank and cup (concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs of 15mm dia pillar tap, fancy tpype, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with letter 'HOT' or 'COLD' with long screwed shanks & fly nuts, screwed for iron pipes complete all as specified and directed.

S&F of Corner glass shelf (large) 300 X 300mm (12" x 12") complete all as specified and directed.

S&F in repair of toilet paper holder fixed to walls with chromium plated (CP) brass screws all as specified and directed by Engr-in-Charge.

S&F of 32 mm bore low density polyethylene pipes (LDPE) of pressure rating 6kgf/cm2 fixed complete to wall or in floors etc. as in outlet pipe for WHB, urinal etc.complete including taking down old unserviceable pipe all as specified and directed.

S&F in repairs of shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) complete all as specified and directed.

S&F of 15 mm dia PVC connection pipe of length 450 mm with PTMT nuts complete all as specified and directed.

S&F in repairs of 20mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipes or for unions pipes, fixed and including taking down old unserviceable gate valve complete all as specified and directed.

S&F in repairs of 20mm dia ball brass valve, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F of 1000 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) multi layer, (three layer) ISI Marked hoisted and fixed in position with cover of tank with its locking arrangement, making hole for inlet, outlet and overflow connection with and including 25mm dia ball valve high pressure of PTMT (minimum weight 455 gms) including dismantling / taking down old unserviceable PVC water tank, ball valve etc complete all as specified in SSR Part-I and directed.

Disconnecting existing water tanks of (exceeding 500 & not exceeding 1000 litres in capacity), setting aside (or lowering if required) and cleaning, removing all scale and dirt etc from tanks and mouth of pipe including hoisting (if required) reconnecting and refixing in position with required fittings complete all as specified and directed. (NOTE: Date of cleaning must be written at side of water tank with white paints after cleaning of tank)

S&F in repairs of vitreous china wash basin, white, flat back, pedestal type of size 630 X 450 mm, excluding taps, chain and plug and porcelain stopper but including waste pipe, brackets and cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F in repairs of 32mm dia waste fittings, brass chromium plated for glazed ware sinks, basins etc. with long screwed shanks & fly nuts, flanged end bedded in red lead cement & other end fixed complete all as specified and directed

S&F in repair of chromium plated tubular towel rail, 20mm dia, D-type, 60cm long between flanges complete all as specified and directed.

S&F of 125mm dia grating with waste hole , fancy type, chromium plated complete all as specified and directed.

Refixing old steel tubings & connections in new or old position (wall, ceiling, floor, trench etc.) for 15 mm bore pipes with new fittings etc after and including taking up or down existing steel tubing and cleaning the same for reuse complete all as specified and directed.

S&F of 15mm dia tubes (medium grade) galvanised iron, with all fittings and fixed complete to walls and ceilings or laid in floors, wall etc (surface or concealed type) after and including taking up or down existing unserviceable steel tubing complete all as specified and directed.

S&F of 20mm dia tubes (medium grade) galvanised iron, with all fittings and fixed complete to walls and ceilings or laid in floors, wall etc (surface or concealed type) after and including taking up or down existing unserviceable steel tubing complete all as specified and directed.

S&F of 25mm dia tubes (medium grade) galvanised iron, with all fittings and fixed complete to walls and ceilings or laid in floors, wall etc (surface or concealed type) after and including taking up or down existing unserviceable steel tubing complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or laid in trenches or in floor after and including dismantling of existing unserviceable pipe any type complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or laid in trenches or in floor after and including dismantling of existing unserviceable pipe any type complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bends any radius provided with access door complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F of 110mm bore PVC(SWR) junction single, (single T) equal or unequal providing access door complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) branch piece, double (double Y) equal or unequal provided with access door complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) bends any radius provided with access door complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F of 75mm bore PVC(SWR) junction single, (single T) equal or unequal providing access door complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) branch piece, double (double Y) equal or unequal provided with access door complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair of chromium plated towel ring of 200mm dia with round flange complete all as specified and directed..

S&F in repairs of 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

Removing plant including roots by dismantling of brick work/PCC/RCC including necessary scaffolding any type in any location/position i.e. roof, parapet wall near pipes etc and applying concentrated hydrochloric or sulphuric acid after removing roots for preventing the regrowth and making good of disturbed portion using PCC (1:2:4) type B0 & 10mm thick plaster in cement mortar (1:3) size of disturbed portion 150mm X150mmX200mm complete all as specified and directed.

S&F steel rack of size 1830mm x 760mmx 1905mm complete all as specified and directed. (Rack shall be as per drawing No. FD-129M and approved by the Accepting Officer)

SCHEDULE 'A' PART-II (ELECTRIFICATION) Taking down carefully copper/aluminium point wiring (light, fan, bell, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, holders, regulators, sockets, light fittings and including making good the disturbed surfaces to match with the existing surfaces by applying white/ colour wash/distemper over applying of putty for smooth finish surface complete all as specified and directed.

M&L for point wiring complete with 1.5 sqmm PVC insulated, FR-LSH type, ISI marked, conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade (MMS) and including cutting, chasing work at any height and all accessories concealed in walls / roofs / floors / ceiling etc. flush mounting MS box with top, bottom, side/back wall knockout for conduit entry from any direction made out of 1.60mm thick and 50mm depth suitable for fixing of modular top cover , blanking plate as per numbers of switch modules, modular switches, sockets, fan regulators, red colour indicator, blank plates etc as approved coloures modular accessories of suitable modules and including 1.5 Sqmm PVC insulated multistranded FR-LSH type unsheathed single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surfaces by applying white/colour wash/distemper as applicable after applying of putty for smooth finish surface complete all as specified and directed for the following:- (Note:- (i) All necessary accessories such as modular box, top cover plate, blank plate, MS box, screws, washers etc are to be used of same make/brand only in relevant items. (ii) Cutting & chasing of wall for point wiring at any height shall be done and cost of the same deemed to be including with quoted rate.)

One light point controlled by one switch .

One fan point controlled by one switch and one regulator.

One 3/5 pin 6 amps socket point controlled by one 5/6 amps switch on independent board .

One 3/5 pin 6 amps socket point controlled by one 5/6 amps switch on same board .

One bell/ buzzer point controlled by one bell push .

All as per Item No.144.00 here-in-before but point wiring with 2.5sqmm PVC insulated multistranded flexible unsheathed copper conductor FR-LSH and earth conductor of size 2.50 sqmm for one 5/6 pin 6/16 amps socket outlet point controlled by one 15/16 amps switch on independent board.complete all as specified and directed.

All as per Item No.144.00 here-in-before but point wiring with 4.0sqmm PVC insulated multistranded flexible unsheathed copper conductor FR-LSH and earth conductor of size 4.0 sqmm for one 5/6 pin 6/16 amps socket outlet point controlled by one 15/16 amps switch on independent board.complete all as specified and directed.

S&F of modular switch 10 Amps, single pole, 1 way, 1 module, 240V, AC, ISI Marked complete all as specified and directed.

S&F of modular type switch 16 Amps, single pole, 1way, 1 module, 240V, AC, ISI Marked complete all as specified and directed.

S&F of modular type bell push 10 Amps, single pole, 1 module, 240V, AC, ISI Marked complete all as specified and directed.

S&F of modular socket shuttered type 6 Amps, 2/3 pin combined 2 module, 240 V, AC, ISI marked complete all as specified and directed.

S&F of modular socket 6/16 Amps, 6 pin combined shutter socket, 2 module with light indication, 240 V, AC, ISI marked complete all as specified and directed.

S&F of modular fan regulator, electronic, stepped type (01 to 4/5), 100 to 120 Watts, 2 module, 240Volts, AC, ISI marked complete all as specified and directed.

S&F of call bell, AC, 230 Volts single pole, multi music type ISI marked complete all as specified and directed.

S&F of modular red colour lighting indication lamp 6 Amps, single pole, 240volts, AC, 50 Hz suitable for 1 module, ISI Marked complete all as specified and directed.

S&F of ceiling rose , three terminal, PVC/polycarbonate body, ISI marked complete all as specified and directed.

S&F of decorative box type 20 -22watt LED fittings with and including LED T-8 tube light 20 watt of fire retardant engineering grade complete with all accessories internally pre-wired, connecting up with and including three core sheathed flexible copper conductor cable of required size and including mounted on PVC/Wooden round/square blocks-02 Nos complete all as specified and directed. (Make - Havells Cat No REGALBATTENT8UPTO1 x 22WDSBSWH & Tube cat No. PHOTONULTRAE2.01213T8SSTL20WLED865SPC/Philips Cat No. TMC501P1XT LED 22WP 3241 for batten and Essential LED TUBE 20W B2B865T8 for tube/SURYA Cat No. SUB118T8LED for batten and SLE TL DS 20 PC REFORM (NANO) for tube or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F of recess mounting 2'x2' LED 35/36 Watt light fittings with LED lamp and required driver, slim in class LED ceiling panel with best in class aesthetic white powder coated frame blended seamlessly with ceiling layout modular ceiling grid and also can be suspended with provided kit and necessary electric connection with and including required size three coat sheathed flexible copper conductor cable from looping box to light fitting and testing complete all as specified and directed. (Make: Crompton Cat No. LCTLRNE-36-F0-CDL/Havells Cat No. VENUSNEOHE2x2R36WLED857PIRSENSOR/ Philips Cat No. RC 383B LED 36S-6500 PSU OD WH PIR/SURYA Cat No. SLE DS 3622R ASTRUM or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F of 10 watt LED light fitting mirror type with high out put diffuser 2 feet, 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size other fixing accessories complete all as specified and directed. (Make: Philips Cat No. WT202W LED 6 SCW PSU S2PC/Havells Cat No. LUMILINE + BS10WLED 865 SPCSS/SURYA Cat No. SLEBT10IL or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F LED light fitting 1x9W/1x10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including fixing arrangements at any hight with nuts, screws and washers and connected to ceiling rose complete all as specified and directed. (Make: Philips Cat No. WT202WLED6SCWPSUS2PC/SURYA Cat No. SLE BH 10W/Bajaj Cat No. BIBWP10W LED or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F round shape 15 Watt, 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. (Make: SURYA Cat No. ATHENA SLE DLR 15W XXRD/Havells Cat No. INTEGRANXTDLR15W LED 857S/Bajaj Cat No. BGSLO Sleek Recess RD15W HW LED or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F of 70/72 watts LED street light fittings, 230 V, IP-65/66 pressure die cast housing LED lamp aluminium compact high power LED street light with heat resistant toughened glass with LED lamp and necessary electric connection with suitable size copper cable after and including taking down old unserviceable fittings complete all as specified and directed. (Make :- CROMPTON Cat No. LST-70-CDL-M/ SURYA CAT NO-SLE UL 72W IP66 LXN/ BAJAJ Cat No. ENXT P 84L WH PO PC SD/ PHILIPS CAT NO. BRP409 LED CW M2 FG PSU OD40 P4498 or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F of 35/36 watt LED street light fittings IP-65/66 pressure die cast housing LED lamp aluminium compact high power LED street light with heat resistant toughened glass with LED lamp and necessary connection with suitable size copper cable complete all as specified and directed . (Make : Crompton Greaves Cat No LSTS-36-CDL-M/ Bajaj Cat No BRTFG 36W LED/Philips Cat No. BRP052 LED 036 CW HP SLAF G SI PSU GR or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

Supply, fabricated and fixing of street light bracket made out of GI pipe 40mm dia medium grade bent to shape of 1.2 mtr long as directed including clamps made out of 40 mm x 6 mm flat iron for fixing bracket suitable for steel tubular poles including nuts and bolts, washers and other connected items of required size including painting with two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed.

S&F of powder coated sheet metal enclosure acrylic door 415 volts AC,TPN distribution board 8 way 8+24 modules suitable for flush mounting with 100 Amps copper busbar, neutral bar, earth bar and MCB incomer of rating upto 100 Amps, MCB TPN/DP, and MCB SP as outgoing and complete connecting cable links with top and bottom removable gland plate with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface and colour coat including taking down old unserviceable one complete all as specified and as directed. (Make:- Legrand cat No. 5076 82 8 way /L&T Cat No. DBTPN008GD or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F of powder coated sheet metal enclosure acrylic door 415 volts AC,TPN distribution board 4 way suitable for flush mounting with 100 Amps copper busbar, neutral bar, earth bar and MCB incomer of rating upto 100 Amps, MCB TPN/DP, and MCB SP as outgoing and complete connecting cable links with top and bottom removable gland plate with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface and colour coat including taking down old unserviceable one complete all as specified and as directed. (Make:- Legrand cat No. 5076 80 4 way /L&T Cat No. DBTPN004GD or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F of powder coated sheet metal enclosure acrylic door 240 volts AC, SPN distribution board 8 way for flush mounting with 200 Amps copper busbar, neutral bar, earth bar and MCB incomer of rating upto 200Amps, MCB SPN/DP and MCB SP as outgoing and complete connecting cable links with top and bottom removable gland plate with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface & colour coat as including taking down old unserviceable one complete all as specified and directed. (Make: Legrand Cat No. 5076 21 8 way /L&T Cat No.DBSPN008GD or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F of powder coated sheet metal enclosure acrylic door 240 volts AC, SPN distribution board 4 way for flush mounting with 200 Amps copper busbar, neutral bar, earth bar suitable for MCB incomer of rating upto 100 Amps, MCB SPN/DP and MCB SP, 10KA as outgoing and complete connecting cable links with top and bottom removable gland plates with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface and colour coat complete all as specified and as directed. (Make:- Legrand cat No. 5076 20 4 way /L&T Cat No. DBSPN004GD or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F of MCB, SP, 6 Amps to 32 Amps , 'C' series, 240 Volt, 10KA, 50 Hz, ISI marked complete all as specified and directed

S&F of MCB, SPN, 32 Amps, 10 KA, 'C' series, AC, 240 volts, ISI marked complete all as specified and directed.

S&F of MCB, SPN, 40 Amps to 63 Amps, 'C' Series, 415 Volts, 50Hz, ISI marked complete all as specified and directed.

S&F of MCB, four pole, 40 Amps to 63 Amps, 'C' Series, 415 Volts, 50Hz, ISI marked complete all as specified and directed.

S&F of MCB, TPN, 40 Amps to 63 Amps, 'C' Series, 415 Volts, 50Hz, ISI marked complete all as specified and directed.

S&F of MCB, TPN, 100 Amps, 'C' Series, 415 Volts, 50Hz, ISI marked complete all as specified and directed.

S&F in repairs of MCCB, 100 Amps, 4 pole, 25KA breaking capacity Icu at 415 Volt with thermal magnetic release, 50 Hz complete all as specified and directed. (Make - L&T Cat No. CM91712OOKOOG or equivalent of Legrand Cat No. 4200-55 or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F of flush mounting sheet steel enclosure metal clad plug and socket including MCB SP 20 Amps, 10KA 'C' series, 240 Volts after and including taking down of unserviceable one complete all as specified and directed. (Make : Legrand Cat No. 5078 11/Havells Cat No. DHDPUSN020/L&T Cat No. DBMPS220SD or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

M&L for earthing with glavanised steel earth plate electrode of size 600mmX600mmX6mm thick buried directly in ground (earth pit not less than 2.25 m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel using GI or steel wire 4mm dia as earthing lead as shown in electrical plate No.3 of SSR Part-I connected to earthing test point all specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC (1:3:6) type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe , 15mm dia GI medium grade earth lead protection pipe and pre-cast earth pit cover 50mm thick made of RCC (1:1.5:3) type A-1 duly reinforced with 8mm dia TMT bar @150c/c both ways, one lifting handle made out of 10mm dia TMT bar 250 mm long embedded in cover slab and cover, wire, copper lugs etc mesh, charcoal and common salt in alternate layer of 15 cm thick complete all as specified and directed. (Notre: Galvanised iron wire of 4mm dia upto 7.5m long including testing is deemed to be included with quoted rate).

M&L for sub main wiring complete with 2 run of 10 sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FR-LSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of required size medium grade (MMS) with all connected accessories such as Bend, Tee, Elbow, Short pieces etc concealed in wall/roofs/floors and including one run of 10 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FR-LSH type as earth continuity conductor connected to common earth dolly and including chease cutting and filling the same with cement mortar and finished with putty and making good the disturbed surfaces to match with existing surface as required for concealed work including taking down old unserviceable submain wiring complete all as specified and directed.

M&L for sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FR-LSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of required size medium grade (MMS) with all connected accessories such as Bend, Tee, Elbow, Short pieces etc concealed in wall/roofs/floors and including one run of 6 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FR-LSH type as earth continuity conductor connected to common earth dolly and including chease cutting and filling the same with cement mortar and finished with putty and making good the disturbed surfaces to match with existing surface as required for concealed work including taking down old unserviceable submain wiring complete all as specified and directed .

M&L for sub main wiring complete with 2 run of 4 sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FR-LSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of required size medium grade (MMS) with all connected accessories such as Bend, Tee, Elbow, Short pieces etc concealed in wall/roofs/floors and including one run of 4 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FR-LSH type as earth continuity conductor connected to common earth dolly and including chease cutting and filling the same with cement mortar and finished with putty and making good the disturbed surfaces to match with existing surface as required for concealed work including taking down old unserviceable submain wiring complete all as specified and directed . (Note for item No. 177.00 to 179.00 : (i)Two runs of cable with one run earth wire and PVC conduit shall be measured as one length. (ii) Extra length of cable required for connection to DBs shall be deemed to be included in the unit rate and shall not be measured separately. (iii) Earth wire shall run inside the conduit. (iv) Suitable color code of wire must be ensured for phase/netural/earth. (iv) All surface cutting/making good for wiring/switch board/junction box/DB etc are included with unit quoted rate.)

M&L for 40 mm bore GI pipe (medium grade) fixed with wall with maximum span of 4.0 meters suitable for hanging of ceiling fan with and including necessary cutting hole in brick/stone wall and making good the same with PCC (1:2:4) type B-1 as required complete all as specified and directed.

S&F of ceiling fan of size 1400 mm sweep, high speed, single phase, 240Volts, AC, 50Hz, BEE 5 Star rated, BLDC fan as approved colour and including hanging GI hook with necessary suitable MS clamps and connecting cable three core 0.75 sqmm round PVC sheathed from ceiling rose to fan connector and testing complete all as specified and directed.

S&F of 450mm sweep Air Circular fan, high speed, single phase, 240Volts, AC, 50Hz, heavy duty stand fan with accessories as approved colour complete all as specified and directed.

S&F of exhaust fan made of sturdy Engineering plastic, AC single phase 230/240 V of size 250 mm sweep, 1200 RPM with louver and necessary connection, testing including cutting the existing wall surfaces of brick/stone masonry and making the hole of any height for fixing the exhaust fan with nuts, bolts and washers after grouting in PCC including mild steel jalli and wooden frame for avoid insects complete all as specified and directed.

M&L for XLPE insulated, LT armoured electric cable with aluminium stranded conductor 1100 volts grade, cross-sectional area 35 sqmm, 3.5 core laid in trenches/pipes/ducts/wall/borings with necessary cable lugs and glands, nuts, bolts and washers etc and testing complete all as specified and directed. (NOTE: Excavation/earth work, sand cushioning, cable cover/brick shall be measured and paid separately if required).

M&L for XLPE insulated, LT armoured electric cable with aluminium stranded conductor 1100 volts grade, cross-sectional area 70 sqmm, 3.5 core laid in trenches/pipes/ducts/wall/borings with necessary cable lugs and glands, nuts, bolts and washers etc and testing complete all as specified and directed. (NOTE: Excavation/earth work, sand cushioning, cable cover/brick shall be measured and paid separately if required).

M&L for sand cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep including required watering and consolidation after laying and stretching the cable complete all as specified and directed. (Note: Only punned down volume of sand to be measured).

M&L for brick covering with width equal to length of brick as protection to cable with well burnt sub class ‘B’ bricks of size 250mm x 125mm x 75mm laid dry flat complete all as specified and directed.

Supply, fixing and commissioning water heater storage type, eletric operated, capacity 25 Litres, BEE 5 Star rated complete with all connected accessories suitable for AC supply, 240 volts, 50 Hz including connecting with water supply pipe line and all water and electrical connection complete with necessary PVC connection pipe all as specified and directed. (Make: Crompton Model No. Arno Neo 25-L5 Star, Bajaj Model No. Montage 25L 5 Star or equivalent model/make as Appx 'A' of PS)

Supply, Installation, commissioning and testing of Split Type wall mounted Air Conditioner (indoor & outdoor unit with cordless remote control unit) of Capacity not less than 2.0 TR, minimum BEE 3 star rating (not less than), fitted with rotary compressor (5 year Warranty), Refrigerant type R-410A/R-32, cooling capacity rated (6450/7033 Watts), PVC FRLS grade multi stranded copper conductor cable 4 core 2.5 Sqmm for connections with outdoor unit, clamps, nuts, bolts, washers, drilling holes on walls/ceiling for connection/drain pipes and making good the disturbed surfaces of wall/ ceiling with cement mortar, white cement and painting work to match the existing surfaces of walls complete all as specified and directed. (Make:- Latest Model of Daikin/ Latest Model of O-General/ Latest Model of Hitachi or equivalent latest model and make of Blue Star.) {Note :- (i) PVC drain pipe of suitable size & Heavy Duty copper connection pipes including suitable insulation upto 3 mtrs are deemed to be included in above quoted rate. (ii) PVC drain pipe of suitable size & Heavy duty copper connection pipes including suitable insulation Exceeding 3 mtrs shall be measured and paid seperately under relevant item.

Supply, Installation, commissioning and testing of voltage stabilizer for automatic operation single phase, wall mounted, copper wounded air cooled, with digital display desinged for input variation between 170 volt to 260 volt with output voltage 220 + 9% volt with calibration accuracy + 3% with high low cutoff, inteligent time delay facility of capacity 5.0KVA S complete all as specified and directed. (Make:- AE/APLAB/ ANREWYULE/ INDIAN TRANSFORMER & ELECTRICALS P. LTD./ V-GUARD/ VOLINA/ VINITEC)

S&F of refrigerator of capacity not less than 308 litres electric drivens, single phase, double door 5 star rated, stainless stell body 10 years compressor warranty complete all as specified and directed.

Taking down old unserviceable GI earthing complete all as specified and directed.

Taking down old unserviceable 40mm dia GI pipe complete all as specified and directed.

M/S. ARUP KUMAR DEY

DE CONSTRUCTION CO

PRESCIENCE TECHNO INDUSTRIES

N C DUTTA

R N CHATTERJEE

SITALA COMMERCIAL AND CONSTRUCTION COMPANY

KOLAY CONSTRUCTION