REPAIRS / RENEWALS OF STREET LIGHTS AND ALLIED WORKS AT ZONE II AND D, REPAIRS TO LT OH LINE, LT UG CABLE, LT PANELS, STREET LIGHTS AND ALLIED WORKS AT UNIT 289, UNIT 371 AND UNIT 729 UNDER AGE E/M NO II OF GE (U) SECUNDERABAD

Amount

Taking down/out unserviceable UG Cables of any Cross Sectional Area and Connections including Pipes, Bricks, etc. of any descriptions, laying in Trenches and/or fixing with Walls/Poles including Segregating of Serviceable Materials viz Bricks, Pipes, etc. and keep in Safe custody for re-use, complete all as specified and as directed.

Supply and lay in trenches/fixed to walls/poles etc connecting buy using lugs and commissioning XLPE insulated and PVC sheathed heavy duty LT 1100 Volts grade armoured under ground cable with aluminium conductor of 2 Core 10 Sqmm COMPLETE all as directed. Make : Havells/Finolex/POLYCAB/KEI/Gloster Note :- Earth work excavation, sand cushioning and brick protection shall be measured and paid separately.

All as per item No 02 above but 4 Core 10 Sqmm

All as per item No 02 above but 4 Core 16 Sqmm

All as per item No 02 above but 4 Core 25 Sqmm

All as per item No 02 above but 3.5 Core 50 Sqmm

Relaying of LT cable of size 10 Sqmm to 120 Sqmm 2/3.5 core after carrying out necessary Repair such as joining with Epoxy joint and laid with sand Cushioning and brick protection and making connection By using Lugs all as specified and directed by ingr in charge. Note: ( Earth work , sand Cushioning, brick protection, Lt Joints shall be measured and paid separately under Relevent Item) (b) Retrived serviceable bricks/ PCC cover shall be reused under relevent item)

Supply and lay GI tubing 50 mm bore light grade for cable protection at road crossing / on poles/ fixing of post top lantren and tubing sealed at both ends after laying the cables complete all as directed by Engineer-in-Charge. Make :- ISI

All as per item No 8 above but 40 mm bore

Supply and Fixing of cable jointing kit for 1.1 KV grade cable for outdoor end termination heat shrinkable type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 25 sqmm to 50 sqmm complete including taking out old unserviceable one all as specifide and directed.

Cutting & trimming of tree branches any girth and size touching to overhead lines ( HT/LT) and cleaning the distance 1.5 mtr both sides of overhead line with in a gap of span average 35 mtrs each depositing the same for cleaning the site all as directed by the Engr-in-Charge.

Excavation in trenches not exc 1.5 mtr wide and n.exc 1.5 mtr in deep and getting out in Hard/Dense soil laying of cables etc.

Returning filling in including spreading, leveling watering and well ramming in layers n.exc 25cm thick using excavated soil

Removing excavated surplus soil to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5mtr above from the starting point

M & L for brick protection cover of old size bricks common burnt clay building bricks sub class ’B’ of size 230 X 113 X 75mm laid dry and flat abutting each other with width equal to length of brick and gap between adjacent bricks not exceeding 10 mm complete all as specified.

Supply and spread approved riddled earth for foundations/Cable duct including watering and consolidation, cushioning of cable laid in trenches complete all as directed by Engineer-in-Charge Note:- Punned thickness will be measured for payment purpose

Laying only old Brick in trenches for Under Ground Cable Protection (Serviceable Materials obtained from Item No. 1 here-in-before), complete all as directed.

S&F galvanised steel strip 32X6 mm with saddles and fixing screws on poreceling insulator/ spacer fixed at every 1 mtr length as lightening conductor on roof/wall of explosive building and joining the same with existing earth test point all as directed by Engr-in-Charge.

Advance Maintenance Free G.I. SAFE EARTHING Electrode with PIPE of not less than 50 mm outer dia) and two meter length, The electrode should be of galvinised (80 -100 micron) along with earth lead as Galvanised steel strip of size 32 X6 mm 7.5 m . The GI Electrode shall be pre-filled with Cristaline Conductive Material (CCM) . The GI electrode shall be surrounded with 25 kg BackFill compound to provide maximum contact between the electrode and Back Fill Compound. The earting pit cover should be factorty built ( size TOP- 10 Inch, Bottom -13 Inch, Height 10.25 Inch ) made of heavy duty Polypropylene complete all as specified and directed make ASHLOK / INDELEC/JMV /TERCEL/TRUE POWER

M&L preparing Steel and Iron Surfaces of any description, over 100 cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L for straight Through Joint heat shriankable type suitable for 1100 volt 10 to 25 Sqmm 4 core complete all as specified and directed

M&L for straight Through Joint heat shriankable type suitable for 1100 volt 35 - 50 Sqmm 3.5 core complete all as specified and directed

M&L for road crossing/drain crossing by adopting trench less tunneling work through specified pipe jacking method by erecting the equipment to true to the allignment and gradient by haidrolic pipe jacking technique complete including tunneling, excavation in any type of soils including hard rock, GI pipe Medium Grade of size 50 mm dia in any length including jointing materials to carry LT UG cables of size upto 50 Sqmm and necessary conveyance charges of machinery and other required materials in co-ordination with the concerned authorites complete all as specified and as directed including refilling and making good of disturbed surface . Note : Quoted rate includes for GI Pipe 50 mm dia medium grade and necessary machinaries required for the above work

Supply and fixing by replacing, MCB TPN 32 Amps 10 KA, C Curve complete all as directed

Disconnection and removing of MCCB's 415 volts 4 pole 35 / 36 KA with and including both side spreader link of breaking capacity Adjustable type of 160 Amps Capacity burnt out one from the existing position supply and fixing the new one making connections including install and testing complete all as specified and directed. Make : L&T/Legrand/Havells/standerd.

All as per item No 25 above but MCCB's 415 volts 3 pole 25 KA breaking capacity Adjustable type of 160 Amps Capacity

All as per item No 25 above but MCCB's 415 volts 3 pole 16 KA breaking capacity fixed type of 100 Amps Capacity

All as per item No 25 above but MCCB's 415 volts 4 pole 16 KA breaking capacity fixed type of 100 Amps Capacity

All as per item No 25 above but MCCB's 415 volts 3 pole 16 KA breaking capacity fixed type of 63 Amps Capacity

All as per item No 25 above but MCCB's 415 volts 4 pole 16 KA breaking capacity fixed type of 63 Amps Capacity

M&L for PCC 1:2:4 type B2 using 40mm graded aggregate as in coping /pedestals of poles including necessary form work and applying two coats of white wash to exposed surface of coping/platform complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40mm graded aggregate as in foundation, filling and mass concrete for pole / stay / post etc complete all as specified and directed.

M&L for twin core 1100 volt grade aluminium service wire cross sectional area 2.5 Sqmm for connection of light complete all as specified and directed including taking down old one

M&L for twin core 1100 volt grade aluminium service wire cross sectional area 4.0 Sqmm for connection of light complete all as specified and directed including taking down old one

M&L for twin core 1100 volt grade aluminium service wire cross sectional area 6.0 Sqmm for connection of light complete all as specified and directed including taking down old one

Disconnection existing LT UG cable of any size from pole/Oh line and connect the same to pole after repair or federpiller box by using cable glands , lugs etc as required complete all as directed

Cutting the existing road straight by manual, depth and width not less than 0.6 mtr below ground level for passing of underground cable and filling back with excavated soil upto 75% road portion and 25% shall be made with cement concrete 1:2:4 (using 20 mm graded aggregate stone complete all as specified and directed.

S&F MCCB box made of CRCA sheet of 2mm thick of suitable size Powder coated Suitable for fixing at Pole including two set of clamps / wall byusing anchor bolt comprising MCCB 63 Amps 16 KA FP WITH BOTH SIDE SPREADER LINK complete all as specified and directed.

S&F MCCB box made of CRCA sheet of 2mm thick of suitable size Powder coated Suitable for fixing at Pole including two set of clamps / wall byusing anchor bolt comprising MCCB 100 Amps 16 KA FP WITH BOTH SIDE SPREADER LINK complete all as specified and directed.

S&F MCCB box made of CRCA sheet of 2mm thick of suitable size Powder coated Suitable for fixing at Pole including two set of clamps / wall byusing anchor bolt comprising MCCB 125 Amps 16 KA FP WITH BOTH SIDE SPREADER LINK complete all as specified and directed.

Supply and Replace Change over switch 100 amps side handel ONLOAD type 4 pole 415 volt without enclosure . Make: Havells/L&T/Schneider

Supply and Replace Change over switch 63 amps side handel ONLOAD type 4 pole 415 volt without enclosure. Make: Havells/L&T/Schneider

Supply, installation, test and Commissioning CPRI APPROVED factory fabricated, out door type, LT FEEDER PILLAR BOX made out of 3.15 mm thick CRCA Sheet with projected Globe roof for rain water protection Dust and Vermin Proof, Double door with both side opening including Neoprene Rubber Gasket, suitable for 440 Volt 3 Phase 4 Wire System ,including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate comp-lete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeded with 50X50X6mm Mild Steel Angle Iron Frame and 600 mm above the Normal Ground Level complete with internal connection with suitable size of cable, cable lugs and cable glands PCC Foundation in Cement Concrete 1:3:6 (20mm Graded Stone Aggregate) and Test-ing after Installation complete all as specified and comprising of the following :– (SIZE NOT LESS THAN 1.05mx0.75mx0.4m)

(a) Aluminium bas bar 300amps - 04 Nos, supported with suitable size of heavy duty porcelin stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving. The bar shall be colour coded (red, yellow and blue) for three phases and black for neutral. (b) MCCB 200 amps,415 volt,16 KA Breaking capacity 4 pole Electromagnetic release duly connected to Bus Bar As IN COMING - 02 Nos Make Legrand model no: 420018/ Equivalent from Schinder/L&T/Hagar/Havells Note:(i) All Internal connection between MCCB and Changeover and Bus bar shall be connected by aluminium strip of suitable size and capacity. (II) All MCCB to be connected with both side Spreader Link. The rate shall deemed to be include in the item rate

Supply and fix on wall with necessary arrangements busbar chamber 100 amps 4 way 4 pole wall mounted IP -31 , made out of 1.6 mm thick CRCA sheet epoxy powdwer coated single layer operational voltage 440 Volt , Short circuit current capacity 25 KA for 1 Second including necessary cable connections complete all as specified and directed. Note: Quoted rates inclusive of necessary fixing arrangement and cable connections , cable glands as required for proper fixing / functioning of Bus Bar Chamber. Make : Havells/ HPL/Standerd,

M&L for replacement of cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including welding, bending cold or hot, drilling holes for hinged, in any shape or size as indicated for valve chamber top cover, 4 mm thick MS sheet cover fixed on 40 mm X 40 mm X 6 mm thick angle iron frame with locking arrangement, mild steel handle, and painting to steel surfaces with two coats of synthetic enamel paint over one coat of primer including disposal of surplus soil to a distance not exceeding 50 m etc complete all as specified and directed.

Cutting the existing building plinth protection/ Floor by using suitable cutter , depth and width as required for replacement of LTUG Cable of any size /any kind of pipes pipes up to 50 mm dia and making good of disturbed surface shall be made with cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) to match with the adjoining surface complete all as specified and directed.

Taking down unserviceable street light fittings of any watt ( tube light / T5 fittings only/SVL/MH FITTINGS) existing position on pole/ wall/ tower, complete and deposite to MES store yard complete all as specified and as directed

Taking down serviceable street light fittings of any watt and type from existing position on pole/ wall/ tower including bracket / clamp and refix the same at new location in pole complete all as specefied and directed.

Taking out unserviceable junction boxes of any type or size for replacement from pole/wall and removing the same from site completeall as specified and directed.

Taking down old unserviceable post top lantern/bollard / Garden/ Gate light fitting of any watt and type from existing position complete for repair and replacement all as specified and as directed

Supply, fixing, connecting and testing post top light fitting in spherical shape polycarbonate PMMA clear diffuser and IP65 protection, new generation energy saving and environmental friendly long life aesthetically desinged aluminium decorative luminaires with high power LED as light source of capacity 1X35/40 watts, fixed to Pole/Wall in any position including taking down old existing street light fitting of any type and capacity complete all as specified and directed. Make:- PHILIPS Cat Part No BGP161 LED2500/NW PSU 220-240V 7043 IN or CG MODEL NO LPTO 40 CDL/ Surya model lP07 501-XXX-57-CL / Havells Cat No. RUBYPT35WLED757PSYMTOPC or Wipro cat No.LP07-501-XXX-57-CL.

Supply, fixing, connecting and testing decorative LED Bollard light with opal diffuser and aluminium reflector of 8/9/11 watt LED including nut, bolts, washers, clamps etc as in repair complete all as specified and directed. Make:- C&S Cat Part NoLTGLCW9WLED or SURYA MODEL NO SLEBL 6W BLK800 or Havells Cat No. BAMBOOBL8WLED830SSYMTOPCM (1.0) or Wipro cat No.LB14-131-XXX-65-05.

Supply, fixing, connecting and testing energy saving, environmental friendly long life Varsatile pressure die cast aluminium alloy for housing (heat sink) with IP66 protection road way light fitting with high power LED as light source of capacity 60 watts with warranty option of 2 years with suitable driver and cable gland for maintaining ingress protection with Epoxy powder coated siemens grey finish after phosphochromate treatment, Tempered protective toughened glass,thermal shock and impact resistant fixed to the housing with SS screws , High efficiency long life LED chip in modules with lumen efficacy of >140 lm/W with PC lens and system lumen 6000. Powered by Built-in electronic LED driver with APFC (SMPS based constant current supply), lower THD, Open Circuit protection, Phase to Phase protection, Over Voltage protection, Surge Voltage protection. CCT 5700, CRI>70, THD<10%, PF>.95, IP66, IK07.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +50 DEG.C; Input Supply Voltage Range:140-270 V, Frequency : 50-60 HZ, Driver safety requirement standards :IS 15885-2-13, Test report to be submitted for Driver performance requirements as per IS 16104, for Photo bilogical safety norms as per : IS 16108, Certification as per LM 79 for Luminaire , LM 80 for LED Source, with all standard accessories etc, including disconnecting and taking down old existing light fittings any type/capacity from any height/position complete all as specified and as directed. Make: Bajaj Cat No.BRTFG 60W LED V3 or Havells Cat No. ENDURAPEARLPLUSSL60WLED757SASYTOPC, SURYA CAT NO: SLEUL60W IP66 (LXN) or Wipro cat No. LR02-671-XXX-57-XX/ equivalent from CG / Philips

All as per item No.53 above, but 70/72 Watt LED Street light fitting with minimum system lumen out put 9000 lumen. Make: Bajaj Cat No.BRTFG 70W LED I or Havells Cat No. ENDURACITYLINERNEOSL70WLED757PASYBOTG, SURYA CAT NO: SLEUL72W IP66 (LXN) or Wipro cat No. LR02-781-XXX-57-G2.

All as per item No.53 above, but 90 Watt LED Street light fitting with minimum system lumen out put 9000 lumen. Make: Bajaj Cat No.BRTFG 90W LED I or Havells Cat No. ENDURAPEARLPLUSSL90WLED757PASYTOPCASTHO, SURYA CAT NO: SLEUL90W IP66 (LXN) or Wipro cat No. LR02-102-XXX-57-XX , equivalent from CG / Philips.

All as per item No. 53 here-in-before but Flood light of high power LED as light source of capacity 200 watts.. Make: Make : Bajaj Cat No.BARFEG 200W LED or Havells Cat No. JETAVALOURFL200WLED757PINTWBLTG, SURYA CAT NO SLEFEL200 WATT IP66 LUMOS II or Wipro cat No. LF20-272-060-57-G2, equivalent from CG / Philips .

All as per item No. 53 here-in-before but Flood light of high power LED as light source of capacity 150 watts.. Make: Make : Bajaj Cat No.BARFEG 150W LED or Havells Cat No. JETAIRISFLS150WLED757PSYMLTG, SURYA CAT NO SLEFEL150 WATT IP66 LUMOS MAX or Wipro cat No. LF20-192-060-57-G2, equivalent from CG / Philips .

All as per item No. 53 here-in-before but Flood light of high power LED as light source of capacity 100 watts.. Make: Make : Bajaj Cat No.BARFEG 100W LED or Havells Cat No. JETAIRISFLS100WLED757SYMLTG, SURYA CAT NO SLEFEL100 WATT IP66 LUMOS MAX or Wipro cat No. LF20-122-060-57-G2, equivalent from CG / Philips . Notes for item Nos 53 to 58 :- (i) LED's used should be the make of Cree/Osram/Lumilieds/Nitchia, (ii) Contractor has to produce LM-79/ LM-80 certificate along with purchase vouchers and Guarantee certificate from Manufacturer. (iii) Surge protection (In-built) of the drive shall not be less than 10 KV or equivalent model in philips or Wipro.

Supply and lay PVC Insulated , PVC sheathed industrial HV round multicore flexible cable with copper conductor THREE core 2.5 sqmm including PVC conduit 20 mm dia medium grade and necessary bends, fittings and fixtures as required for connection of light fittings . ( uSED FOR GARDEN LIGHT CONNECTION, EXCAVATION , RETUNING FILLIING ETC WILL BE MEASURED AND PAID SEPARATELY.

Supply and fix locally available Acrylic glob light best quality clear with and including LED bulb 9 watt of 200 mm dia complete suitable for fixing in 40/50 mm dia GI pipe including necessary connections complete all as specified and directed including taking down old one .

Supply and fix locally available Acrylic glob light best quality clear with and including LED bulb 9 watt of 300 mm dia complete suitable for fixing in 40/50 mm dia GI pipe including necessary connections complete all as specified and directed including taking down old one .

Supply, lay, test and commissioning of galvanized iron tubing 50 mm bore light grade with all fitting for fixing of garden light incl necessary clamp, bolt/nut if any and making hole on wall complete all as specified and as directed.

Material and Labour for drawing two runs of PVC insulated unsheathed single core multi stranded copper conductor FRLS cable of size 2.50 sq mm with one run of PVC insulated unsheathed single core multi stranded copper conductor FRLS cable of size 2.50 sq mm including 20mm dia PVC conduit of dia 20 mm medium gradeexclusive of boxes but inclusive of all tees, bends, elbow, reducers etc and fixing accessories such as couples, lock nuts, saddles, pipe hooks, clamps etc complete all as specified

S & F hot press moulded SMC junction / terminal box of size with internal diamensions of 200 x 140 x 95 mm with hinged door, incl provision of 2 way connector 415 Volts made out of polycarbonate or bakelite and 1 No MCB of 6 Amps with DIN bar, drilling holes for cable connections, connecting incoming and or out going cables by providing suitable of size of cable lugs/glands, fixied on pole by means of clamps made out of MS flat iron of size 25 mm x 3 mm including dismantling of old unserviceable all as specified and as directed.Make: Hensel/Syntex/C&S/nyptune

Supply and replace contactor ML 3 with coil operating voltage 230 Volt complete all as directed

Supply and replace contactor ML 2 with coil operating voltage 230 Volt complete all as directed

Supply and replace Timer Analog Type Suitable for 24 hours operation of street light of 16 amps capacity (LEGRAND/AVV/CG)

Supply and Replace MCB SP 32 Amps 10 KA, C Curve complete all as directed

Fabrication and installation of GI pipe bracket made of midium Grade tubing of size 40 mm dia, duly bended by hot forgoing after filling of sand, length 1.20 mtr including providing two pair of MS flat strip clamps 40 mm x 4 mm with GI bolts nuts and washer complete all as specified and directed

Material and labour for Taking down UNSV LED Lights and removing Carbon from its connector joints incl replacement of Connecting wire with new PVC sheated weatherproof 3X single core cable for electrical connection and refixing the fitting after repair to its original/New location or as directed by engr-in-charge.(connecting wire will be measured and paid separately only)

Supplying, erecting and fixing steel tubular swaged poles with cast iron base plate of size 300mm x 300mm x 6mm, finial taper plug, bolts, nuts & screws for type 410 SP-31 (9.0 mtrs long) including painting with two coats of aluminium paint over one coat of red oxide primer on all exposed surfaces and tarring with black bituminous paints to embedded portion in PCC and providing 3 Nos of 30cm wide circular bands with black & yellow paint starting from plinth level at a gap of 30 cm in between 2 bands and numbering of poles, in yellow paint over black painted back ground at a height of 2m from bottom of pole with 5 cm large bold letters 2" (inch) wide including taking down old unserviceable PCC poles of any type complete all as specified and directed. Note: Excavation, earth work, PCC in foundation and coping shall be measured and paid separately under relevant item of this schedule.

Supply and fixing lantren of dia 60 CM for fixing of flood light, cap type to be fixed on the top of 9 m SP-31 Steel pole , made of MS pip medium grade dia greater than the top dia of the pole of length 0.35 M supported by MS flat iron of size 50X6 mm 8 nos including two coat of aliminium painting over a coat of redoxide primer complete all as directed

Excavating in trenches, not exc. 1.50 METRE wide and exc. 1.50 METRE but not exc. 3.00 METRE in depth, for Foundation of Poles, etc. and getting out in Soft/ Loose Soil, complete all as specified and as directed.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate for filling & foundation of pole & mass complete all as directed

Disconnecting from over head conductor, cutting worn out portion of LT cables of any type and size, carry out repairs including taking out cables from under ground loop line and rejoining the same to restore electric supply. Note :- (i) LT Jointing Kits, Cable protection Pipe if required at site will be measured and paid separately. (ii) Quoted rate is deemed to be inclusive of cutting and removing the pole coping and inserting the cable alongwith protection pipes.

M&L for ACSR conductor, steel reinforced for LT over head lines on poles including streching tightining of poles insulator with binding wire of suitable size with insulator/streching of ACSR conductor including disconnecting/taking out old existing unsv ACSR conductors complete all as specified and directed.

M&L for Pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 100 mm height, 65 mm dia for 1100 volts grade, including disconnecting/taking out old existing unsv insulators complete all as specified and directed.

M&L for Shackle type, Porcelain, vitreous, white, brown or green insulator including galvanised mild steel straps, washers, insulator bolts, washers and nuts of size 100 mm height, 115 mm dia for 1100 Volt grade, section of straps 31x5 mm, including disconnecting/taking out old existing unsv insulators complete all as specified and directed.

S&F Stay assembly comprising of 7/10 SWG galvanised MS stranded stay wire of required length, minimum tensile strength 70 Kg/mm (grade-2 quality) fixed to pole with and including FI clamps, bolts, nuts, washers, galvanised steel stay rod 16mm dia 180 cm long bow 400 x 14 mm nuts/bolts, washers, loop type insulator of size 65 x 90 mm vitreous, clearance dia of hole 16mm, stay plate of size 230 x 230 x 6 mm including necessary excavation and earth work PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate in foundation and disposal of surplus soil, upto 50m including disconnecting/taking out old existing unsv stay assembly complete all as specified and directed.

S&F of Galvanised steel wire (GI) 4mm dia including disconnecting/taking out old existing unsv GI wire complete all as specified and directed.

Restreching/Restringing, tightening and repair to overhead line ACSR conductor of any size on LT poles including necessary Aluminium binding wire connectors PVC sleeves for jumper, fixing of insulators and prunning of tree complete all as specified and directed. Notes: (i) The distance between pole to pole in one span (contains 4/6 runs) i.e one span will only be considered for payment purpose. (ii) No Extra conductor will be measured for binding to insulators / jumpering etc.

M&L for painting the existing LT steel poles of 9.0 Mtr long including cross arms, clamps, street light junction boxes etc with 1 coats of aluminium paint including throughly cleaning the existing surface, writing of pole numbers in yellow circle 15 cm with black paint on poles. Painting the poles up to 1.5 Mtr height with alternate bands 30 cm height (3 Nos black and 2 Nos Yellow) from ground level, complete all as specified and directed.

M&L for Painting the existing LT PCC poles with 1 coats of synthetic enamole base paint including painting of cross arms, clamps, etc with one coat of aluminium paint and providing alternative band of 30 cm width (3 black and 2 yellow) from bottom of pole to 1.5 metres height , writing of pole numbers in yellow circle15 cm with black paint on poles complete all as specified and directed.

S&F LED High Bay light 90 W lumanaries with with high luminous efficacy,IP 65 protected, front toughened glass with discrete high lumen LED along with Reflector including dismantling of old unserviceable fitting all accessories complete all as directed. (Make - Surya Cat Ref: SLE HB 90 W COMET AND RFHB 90 COMET or equivalent make of Philips/CROMPTON/HAVELLS).

Supply and fix locally available gate / garden light best quality metal Silver / metal black Decorative Exterior of size not less than 300 mm X220 mm with and including LED bulb 9 watt suitable for outdoor installation and suitable for fixing in 40/50 mm dia GI pipe including necessary connections complete all as specified and directed including taking down old one. Make : Jhoomarwala or equivalent make as approved by GE.

Supply and fix locally available gate / garden light best quality Black Color Steel Shade With Fiber Glass Outdoor Gate Lamp of size not less than 360 mm X250 mm with and including LED bulb 9 watt suitable for outdoor installation and suitable for fixing in 40/50 mm dia GI pipe including necessary connections complete all as specified and directed including taking down old one. Make : Jhoomarwala model SKU: (PM-GT-10-BIG) / equivalent as approved by GE

Sri venkateswara Electricals

Dwarka Pershad Radhey Ramanlal

L and S ENTERPRISES

DPS sales and services india

STANDARD AGENCIES

Srinivasa Consructions

Srinivash Engineers