SPECIAL REPAIRS TO BUILDING NO P 139 SNCOs TRAINEE ROOMS AND LIVING IN STAFF ROOMS AT MTC CHAFB BANGALORE

Amount

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubing down with water etc complete all as specified and directed

Demolition of brick or stone/boulders masonary, built in cement morter complete all as specified and directed

Demolition of cement concrete in ground floor and paving n/exe 15 cm thick below or above GL complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not balking) removing serviceable tiles to store complete all as specified and directed

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in cement mortar complete all as specified and directed

Demolition of reinforced cement concrete of any description ( reinforcement cut as reqd to facilitate demolition ) complete all as specified and directed

Dismantling plain or corrugated steel sheeting any guage, thickness including roof covering etc complete all as specified and directed

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n/exe 1.50 Sqm each complete all as specified and directed.

Taking down chowkhat or frames with shutters exc 1.5 sqm but n exc 4 sqm each (w/o taking of shutters from the frame).

Taking down shutter of any description exe 1.00 sqm but n/exe 2.00 sqm and re fixing in the same opening incl easining etc complete all as specified and directed.

Taking down shutter of any description exe 1.00 sqm but n/exe 2.00 sqm complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B1 (20mm graded aggregate) as in sub base/levelling course complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type C1 (using 20 mm graded aggregate ) as in sub base for receiving floor finishes/plinth protection etc. complete all as specified and directed.

M&L for 100 mm thick PCC (1:2:4) type B2 (using 40 mm graded aggregate) as in hard standing floor finishes etc. laid in alternate panels complete all as specified and directed.

M&L for chequerd cement concrete tiles glossy finished 30cm x30cmx25mm th with grey cement and pigment , set , jointed and pointed in neat cement slurry in floors laid over 15 mm thick screeed bed in CM 1:6 complete all as specified and directed

M&L for Non - skid Ceramic coloured joint free tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed bed or bedding in CM 1:4 complete all as specified and directed.

M&L for Non - skid Ceramic coloured joint free tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 10mm thick rendring in CM 1:4 complete all as specified and directed.

M&L Marble work 18 to 20mm thick (table rubbed and polished) makrana white in steps, jambs, pillars, windowcills,cooking platforms, border and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment set, jointed and pointed in neat cement slurry in floors laid over 20mm thick screeed bed in cm 1:6 complete all as specified and directed

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:3) mixed with waterproofing treatment with using integral waterproofing compound conforming to IS:2645 as per manufacturers instruction all as specified and as directed. Note : WPC will be measured and paid seperately.

Supply only integral WPC conforming to IS:2645.

M&L for cement concrete type F2 (1:7:12) using 40mm graded aggregate as in foundations, filling and mass concrete in sunken floor all as specified and as directed.

M&L for Non skid ceramic coloured joint free tiles 7mm to 8mm thick (square/ rectangular), area of each tiles exceeding 0.06 sqm but n exc 0.11 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles, laid over and including cement screed bed 15 mm thick in cement mortar (1:6) laying floor finish complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surfaces 300mm x450mmx 7mm/ 300mmx600mmx7 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match laid over 10mm thick cement plaster in CM (1:4) complete all as specified and directed.

M&L for Pre cast cement concrete block masonry with soild blocks, type C1 (1:3:6) using 20mm graded aggregate exc 10 cm in width and setting in cement mortar (1:6) complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement morter 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering in two coats first coat with 10mm thick in cement morter 1:6 and second coat with 5mm thick in cement morter 1:4 on fair faces of brick work or concrete surfaces with water proofing compound @ 200 ml per 50kg of cement or as per manufacturer's instruction etc finished even and smooth without using extra cement complete all as specified and as directed. (Note : WPC shall be measured and paid separetely)

M&L for rendering 5mm thick on concrete surfaces of ceiling in cement morter 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

M&L Granite 18 to 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and tabil top for fixing wash basin and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 for laying granite all as specified and as directed

M&L for providing, cement concrete type B-0 (1:2:4) using 12.5mm graded stone aggregate as in roof kerbs, padding or mud stops, rounded or chamfered on edges all as specified and directed

M&L for cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry (1:3) complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:3 on roof padding finished even and fair with approved water proofing compound @ 200ml per 50kg of cement or as per manufacturer's instruction all as specified and as directed. (Note : WPC shall be measured and paid separately as supply only under relevent item)

Supply only liquid water proofing compound

M&L for water proofing treatment on horizontal and vertical surfaces with Providing and laying / fixing TPO (Thermoplastic Polyolefin) membrane including cleaning the surface and laying of 200GSM Geo textile and cover up with TPO RF 1.2 mm thermoplastic membrane on roof including upto 300mm of parapets and crumple joint including junction of roof and parapet, welding the seam joints with hot airgun/machine and terminate the corners with extra protection to withstand the high wind pressure. The TPO should be thoughroly tightened with the lower structure using mechanical fastening properly to avoid the corners and seam joint failure. Make :Asian paints TPO or equivalent product of M/s Bauchemic/CIPY/ SIKA/Pidilite/Dr fixit TO membrane

Supply & fixed steel windows box type ERW hollow 'P' section comprising double frame including gauged and glazed skelton shutter 30mm thick jointed internally with flat iron 25x3mm complete including hinges handle tower bolts, stops lugs,grill etc all as shown in drawing CEJZ TD -20 sheet 1/3 to 3/3 as applicable complete Note :- (i) For the purpose of measurement & payment double shutter with frame and grill shall be considered as one unit. (ii) Glazing, wire mesh & painting shall be measured & paid separately.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built upstandard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chief. Note : All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufactures catalouge for the corresponding aluminum sections/fittings.

S&F Pressed steel frames for doors size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc., complete, as specified and directed

S&F Pressed steel frames for doors size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc., complete, as specified and directed

M&L for PCC 1:3:6 type C-1 (using 20mm graded aggregate) as filled in pressed steel foor frames etc complete all as specified and as directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded aggregate) as in hold fast block including necessary form work etc complete all as specified and as directed.

S&F for 35 mm thick factory made second class hard wood plain framed panelled shutter ( two panel) with lock rail and panel of 9mm B.W.P. commecrcial ply or 12mm veneered particle board with commecrcial veneering on both face. The size of rail and stile as per IS 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35mm thick IIst class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, divided into squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc, size of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a) supplied and fitted to chowkats, complete all as specified and directed.

S&F for 4mm thick sheet glass ordinary quality and fixed with aluminium beading in square not exc. 0.50 sqm in each pane complete all as specified and as directed.

S&F for 4mm thick Figured glass, pin head type and fixed with aluminium beading in squares n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and as directed.

S&F for butt hinges 100mm medium weight cold rolled mild steel complete all as specified and directed

S&F mild steel sliding door bolt plate type stove enammelled black of length 300 mm with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate and fixed complete all as specified and directed

S&F 200mm long of barrel tower bolts stove enammeled black with bright bolt omplete all as specified and directed.

S&F 150mm mild steel pressed handles oval type stove enamelled black complete all as specified and directed.

S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm wood grain printed PVC sheet reinforced with MS square tube manufactured as per SSR Part-I specifications and drawings.

S &F Factory made solid PVC Moulded door shutter,28 to 30mm thick (stiles),with 2,4 or 6 raised panel design with 2mm thick Moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face ,with particle board core supplying & fixing in frame at site as per specifications & drawing complete all as specified and directed by Engr-In-Charge.

S & F 100 mm long extruded Aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin, type C22 complete all as specified and directed by Engr-In-Charge.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engr-In-Charge.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed by Engr-In-Charge.

Dismantling water storage tanks of any description, exc 250 litres & n.exc 500 litres capacity and removing from site complete all as specified.

Dismantling water storage tanks of any description,exc 500 litres & n.exc 1000 litres capacity and removing from site complete all as specified.

S&F for Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated alu rod & high density plastic ball complete all as specified

S&F for Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated alu rod & high density plastic ball complete all as specified

S&F repairs Vitreous China wash down water closet pan (Pedestal Pattern), White with 'P' or 'S' trap, including provision of fixing bolts and connecting upto drain and flushing pipe etc. complete all as specified and directed by Engr-In-Charge.

S & F plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engr-In-Charge.

S & F repairs PVC flushing cistern with flush out valve type,10 ltrs capacity,low level white with inlet ball valve, float and handle including bracket including flush pipe complete all as specified and directed

S&F in repairs vitreous China wash basin, white flat back, size 550x400mm including brackets, 32mm dia CP waste coupling, waste pipe, short connection complete cutting for and pinning in ends of brackets or ereesing stand complete all as specified and directed

S&F in repairs 15mm pillar tap,cast copper alloy, with capstan head, chromium plated, fancy type screwed down high pressure,with or without lettered "hot" or "cold" with long screwed shank and fly nuts screwed for iron pipe of 15mm bore complete all as specified and directed

S&F PVC connection pipe 600mm long 15mm dia both end having brass coupling nut and PVC washer complete all as specified and directed

S&F in repairs Toilet paper holder of stainless steel fixed by CP brass screw in wall complete all as specified and directed

S& F Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1 m long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed

S&F 110mm PVC (SWR) WC connector bent type complete all as specified and directed.

S&F in repairs 15 mm bore fancy type, chromium plated Stop valves / Angle cock screwed down high pressure with crutch handle screwed both ends for iron pipe or for unions complete all as specified and as directed by Engr-In-Charge.

S&F in repairs brass chromium plated fancy type towel rail, 20mm dia, D type 600mm long between flanges including brass CP brackets complete all as specified and directed by Engr-In Charge.

S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed.

S&F CP two way stop cock with all accessories complete all specified and directed.

S&F in repairs 15 mm bore fency type CP bib taps cast copper alloy with crutch or butterfly nuts , handle, screwed down for iron pipe complete all as specified and directed

S&F gratings doom , 100mm dia of PTMT(minimum weight 25 gms) complete all as specified and directed

S&F gratings doom, 125mm dia with waste hole of PTMT(minimum weight 40 gms) complete all as specified and directed

S&F 15 mm bore GI tubing med grade galvanished with all fittings including taking up or down and fixed complete to walls & floors etc complete all as specified and directed

S&F 20 mm bore GI tubing med grade galvanished with all fittings including taking up or down and fixed complete to walls & floors etc complete all as specified and directed

S&F 25 mm bore GI tubing med grade galvanished with all fittings including taking up or down and fixed complete to walls & floors etc complete all as specified and directed

S&F in repair 25 mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed.

S&F in repairs 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, all fittings including taking up or down and fixed complete to walls & floors etc complete all as specified and directed fixed on walls complete

S&F in repairs 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls complete all as specified and directed

S&F in repairs (SWR) 75mm dia floor trap,plain with grating incl jointing with solvent cement complete all as specified and directed

S&F 75mm PVC (SWR) bends any radius complete all as specified and directed

S&F 110mm PVC (SWR) bends any radius complete all as specified and directed

S&F 110mm PVC (SWR) vent cowl complete all as specified and directed

S&F 75mm PVC (SWR) vent cowl complete all as specified and directed

S & F PVC (SWR) 75mm bore junction single, (Single T) equal or unequal complete all as specified and directed

S & F PVC (SWR) 110mm bore junction single, (Single T) equal or unequal complete all as specified and directed

M&L for preparation of new plastered surfaces of wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primig paint complete

M&L for applying 2mm thick wall care putty on wall including preparation old/new surfaces plastered or unplastered surfaces , complete all as specified and directed.

M&L for applying two coat of distemper oil emulsion to new treated surfaces of wall including complete removal of existing tratment and preparation of old surface of walls by washing down,rubbing down and stopping of distempered surface, complete all as specified and directed

M&L for preparation of old plastered surfaces of ceiling and applying two coat of white wash complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceilling and applying two coat of white wash complete all as specified and as directed.

M &L for preparing new plastered or un plastered surface of walls and applying two coats of Cement base paint on walls a over alkali resistant priming paint through mechanical means complete all as specified and directed.

M &L for preparing old plastered or un plastered surface of walls and applying two coats of Cement base paint on walls through mechanical means complete all as specified and directed.

M&L for two coats of synthetic enamel paint on new wooden surfaces over coat of pink to new surfaces including preparation of surfaces, over 10cm width or girth complete all as specified and directed.

M&L for two coats of synthetic enamel paint on new steel surfaces over coat of red-oxide primer including preparation of surfaces, over 10cm width or girth including preparing roof painting complete all as specified and directed.

M&L for one coat of synthetic enamel paint on old steel surfaces over coat of red-oxide primer including preparation of surfaces, over 10cm width or girth complete all as specified and directed.

Material and labour for applying one coat of synthetic enamel paint to old painted wooden surfaces of any description, not otherwise described, over 10 cm width or girth including preparaton of surfaces all as specified and direcet by the Engineer-in-Charge.

Removing building materials etc. (other than spoil payable under items -earthwork) to a distance of 30.00 Km or above, beyond the lead included in the rates, including loading, unloading and stacking at the destination all as specified and as directed

Dismentling structural steel work including doors, gates,grills but excluding framed truss etc complete.

Dismentling wrought iron or mild steel work of any description as in angle iron not otherwise provded for etc complete.

S&F angle iron for posts, struts in fencing including cutting tops, to shape as required, drilling holes, notching for wire, including welding etc, confirming to Fe-290 Gde, E-165 complete all as specified and directed

S&F framed work such as grills, gratings etc, with ends of bars, shouldered, end or riveted or forged into spikes framed gaured bars barrel iron doors ladders, framed blausters walk ways,raillings,framed water tanks and similar works confirming to Fe Fe 290 Gde-E-165 complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick as in ridge of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets.

S&F external teak wood lipping for block board or veneered particle board 6mm thick fixed with nails for 18 to 19mm thick all as specified and as directed.

S&F 30 mm wide Continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and directed

S&F 125mm long Hasp and staple, safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed

M&L for 18 to 19mm thick pre-laminated partical board, interior grade, pre-laminated one side with decorative choice lamination & other side balancing white lamination, and fixed with screw and Continuous (piano) hinges, 125mm long Hasp and staple and and prepared kitchen cabinate with shutter (and one or two self as per site requirement for sorage) and hanging on wall and also fixed to timber frame work where required all as specified and directed

M&L 20 mm dia curtain rods of aluminium annodised powder coated fixed including with fixing brackets,stops, rollers etc brackets, fixed as in repairs, complete all as specifed and directed.

M&L for PCC 1:2:4 type B-1, (using 20mm graded aggregate) as in grouting of angle posts, pillars ,coping,plinth courses,parapets and raillings etc including necessary form work complete all as specified and directed.

M&L for PCC 1:2:4 type B-1, (using 20mm graded aggregate) as in surface channel and drains complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light fan socket or power) complete including fittings & fixtures such as switches, ceiling rose, pendants, regulators, sockets, ceiling roses,pendants, regulators, light fittings etc. Removing materials to store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified & as directed.

Taking down ceiling fans from ceiling, dismantaling blades & refixing of the same including provision of cable from ceiling rose or connector to fan all as specified and directed.

Taking down Exhaust Fans, from walls and refixing the same including connecting up and provision of cable from ceiling rose or connector to fan all as specified and directed.

Taking down Geyser from walls, and handing over the same at MES store, complete, ll as specified and directed.

Point wiring with cable of PVC insulated FRLS copper multistranded conductor 1.5 sqmm 1100 volts grade in and including medium grade 20 mm dia PVC Conduit Pipe ISI marked with all accessories and fixing arrangements concealed in Stone walls / brick masonary walls /ceilings / floors etc by cutting chasis in existing stone/ brick masonary, including fixing top cover /PVC /MS Modular type junction boxes concealed in Stone walls / brick masonary walls for housing switches/sockets/ regulators etc. with and including 1.5 sqmm PVC insulated multistranded copper earth continuity conductor connecting to the common earth dolly etc complete all as specified and directed for the following :- (a) One light controlled by 1 switch 5 amps, single pole

All as per Item No. 121 above but for One Ceiling fan point controlled by one single pole 5 Amps switch

All as per Item No. 121 above but for One Exhaust fan point controlled by one single pole 5 Amps switch

All as per Item No. 121 above but for One 3 pin switch socket out let point 5 Amps switch on independent board

All as per Item No. 121 above but for One 3 pin switch socket out let point 5 Amps switch on same board

All as per Item No. 121 above but for One bell Point controlled by one push button 5 Amps switch on independent board

All as per Item No. 121 above but for One light controlled by two nos, 2 way switch 5 amps, single pole

Point wiring with cable of PVC insulated FRLS copper multistranded conductor 2.50 sqmm 1100 volts grade in and including medium grade 20 mm dia PVC Conduit Pipe ISI marked with all accessories and fixing arrangements concealed in Stone walls / brick masonary walls /ceilings / floors etc by cutting chases in existing stone/ brick machinery, including fixing top cover /PVC /MS Modular type junction boxes concealed in Stone walls / brick masonary walls for housing switches/sockets/ regulators etc. with and including 2.50 sqmm PVC insulated multistranded copper earth continuity conductor connecting to the common earth dolly etc complete all as specified and directed for the following :- NOTE : Chases/ groove cutting shall be measured and paid separately under relevant items. NOTE for Item Sl. No 120 to 127 : Chasis/ groove cutting in stone walls/ brick wall/ block masonary walls as required for concealed wiring shall be measured and paid separately under relevant item No 149 & 150.

Supply and fix Modular switch , 1 Module single pole one way 10 Amps.

Supply and fix Modular switch , 1 Module single pole one way 16 Amps.

Supply and fix modular socket , 2 Module 6 Amps, 2/3 pin, 240 volts Ac 2/3 pin combined all as specified and directed

Supply and fix modular socket , 2 Module 6/16 Amps, 2/3 pin, 240 volts Ac 2/3 pin combined all as specified and directed

Supply and fixing of modular type fan regulator upto 120 watts with 5 step speed control for fans any sweep 1200 mm/1400 mm complete all as specified and directed

Supply and Fixing of modular type Bell push 6 A, 1 Module complete all as specified and directed

Supply and Fixing of Ding Dong Bell, AC, 230 volts, Single Pole complete all as specified and directed

Supply and fixing of modular white cover plate with frame, 1 module complete all as specified and directed

Supply and fixing of modular white cover plate with frame, 2 module complete all as specified and directed

Supply and fixing of modular white cover plate with frame, 3 module complete all as specified and directed

Supply and fixing of modular white cover plate with frame, 4 module complete all as specified and directed

Supply and fixing of modular white cover plate with frame, 6 module complete all as specified and directed

Supply and fixing of modular white cover plate with frame, 8 module complete all as specified and directed

Supply and fixing of metal flush box 1/2 module complete all as specified and directed

Supply and fixing of metal flush box 3 module complete all as specified and directed

Supply and fixing of metal flush box 4 module complete all as specified and directed

Supply and fixing of metal flush box 6 module complete all as specified and directed

Supply and fixing of metal flush box 8 module complete all as specified and directed

Supply and fixing PVC ceiling rose 65 x 50 mm surface type with 3 terminals all as specified and directed.

Supply and fixing in repair LED lights fitting 1x 10 W, 220V,AC decorative box type with driver, holder including LED tube light connecting up, complete all as specified and directed.Make : BAJAJ, Model : ivora led batten, CAT NO : 830413, or eqivalent in HAVELLS/ CROMPTON, WIPRO

Supply and fixing in repair LED lights fitting 1x 20 W, 220V,AC decorative box type with driver, holder including LED tube light connecting up, complete all as specified and directed.Make : BAJAJ, Model : ivora led batten CAT NO : 830481, or eqivalent in HAVELLS/ CROMPTON, WIPRO

M&L for Cutting into or through the stone walls / brick walls built in cement mortar or cement lime mortar and walls of cement concrete suitable size for housing for sunk box using heavy duty stone drilling/cutter machine and making good the disturbed surface all as specified and directed.

Cutting chasis, pinning in Stone walls/ brick walls etc. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc, for concealed conduit wiring a into or through the stone walls built in cement mortar or cement lime mortar and walls of cement concrete suitable for housing 25mm dia conduit pipe using heavy duty stone drilling/cutter machine and making good the disturbed surface all as specified and directed.

Supply and fix sub main wiring with Two runs of single core FRLS PVC insulated cable with copper conductor multistranded 1100 volts grade 2.5 sqmm in and including suitable size of non-metallic rigid PVC conduit & accessories, fixing arrangements concealed in stone wall, floor or ceiling etc by cutting chases in existing stone/ brick masonary including one run of single core 2.5 sqmm PVC insulated multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC Conduit and two run of copper conductor together taken as one RM for measuring unit length.

Supply and fix sub main wiring with Two single core FRLS PVC insulated cable with copper conductor multistranded 1100 volts grade 6.00 sqmm in and including suitable size of non-metallic rigid PVC conduit & accessories, fixing arrangements concealed in stone wall, floor or ceiling etc by cutting chases in existing stone/ brick masonary including one run of single core 6.00 sqmm PVC insulated multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC Conduit and two run of copper conductor together taken as one RM for measuring unit length.

Supply and fix sub main wiring with Four single core FRLS PVC insulated cable with copper conductor multistranded 1100 volts grade 10.00 sqmm in and including suitable size of non-metallic rigid PVC conduit & accessories, fixing arrangements concealed in stone wall, floor or ceiling etc by cutting chases in existing stone/ brick masonary including two runs of single core 10.00 sqmm PVC insulated multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and directed. Note : Two runs of earth continuity conductor,one run of PVC Conduit and Four runs of copper conductor together taken as one length for measuring unit length. NOTE for Item Sl. No 151 to 153 : Chasis/ groove cutting in stone walls/ brick wall/ block masonary walls as required for concealed wiring shall be measured and paid separately under relevant item

Material and labour for Earthing complete with galvanised steel earth plate electrode 60x60cmx6mm thick, buried directly in ground, Putting of adequate qty of salt and Char coal in layer by layer by completely covering of earth plate on sourrounding six sides, ( earth pit not less than 2.25mtrs deep below ground level) with top edge of the plate not less than 1.5mtrs below normal ground level, connected to galvanised earth lead wire 4.00 mm dia as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point, provision of PCC earth chamber, Chamber cover, GI funnel with mesh, GI Pipe etc all as including provision all as specified or indicted including testing on completion complete all as specified and directed

S&F Earth Continuity Conductor or main earthing lead fixed to wall on batten or recess or chasis or buried in ground or drawn in conduit / pipe or fixed for earthing etc. of size 4.00 mm dia galvanised iron or steel wire all as specified and as directed.

Supply & Fixing of Sheet metal enclosure for VTPN DB's double door TPN 08 ways Suitable for 125 Amps MCCB Fixed in DB, deep drawn with 200 Amps rated copper bus bar 415 V, IP 43 Protection, Concealed in walls, complete all as specified and directed. Including taking down old unsv from exiting place.

S&F Sheet metal enclosure for DB's double door TPN, 8 ways when MCBs to be used single pole and neutral,deep drawn with 200 Amps rated copper bus bar 415 V, Concealed in walls complete all as specified and directed. Including taking down old unsv from exiting place.

S&F Sheet metal enclosure for DB's double door SPN, 8 ways when MCBs to be used single pole and neutral,deep drawn with 200 Amps rated copper bus bar 240V, Concealed in walls complete all as specified and directed. Including taking down old unsv from exiting place.

S&F MCB TPN, 63 Amps, 415 V, C- series with breaking capacity of 10KA complete all as specified and directed.

S&F MCB SPN, 40 Amps, 240 V, C- series with breaking capacity of 10KA complete all as specified and directed.

MCB SP, 6-32 Amps, 240V, C- series with breaking capacity of 10KA complete all as specified and directed.

Supply and fixing of MCCB 125 A, TPN, 25 KA,

Supply and fixing of LED 36 WATTS building security, Make : CG, Model : FREEDOM NEO, CAT NO : LSTS-36 CDL-M or equivalent in HAVELLS/ BAJAJ/ OSRAM ETC.

Supply and fix Surge protection device Type TP+N, AC Triple pole and neutral, 20kA N complete all as specified and directed.

Supply and fixing of GI Pipe 40 mm dia bend L shaped for fixing of Building security lights, including properly grouting on wall with required fixing arrangements such as bolts, nuts, screws, clamps etc.

Supply and fixing of LED 40 WATTS Decorative post top light fitting, Make : CG, Model : MAPLE, CAT NO : LPTO-40 CDL-M or equivalent in HAVELLS/ BAJAJ/ OSRAM

Supply and fixing of LED Bollard 10 Watts, light fitting, inverted pyramid tripod type with soft 360 degree Make : CG, Model : LIARA, CAT NO : LBLSN-10 CDL-M or equivalent in HAVELLS/ BAJAJ/ OSRAM ETC.

Supply and fixing of Pole mounted Junction box enclosure 240 x 130 x 110 mm complete all as specified and directed

kamadhenu Electricals (BID ID -3296568)

OM ENTERPRISES (BID ID -3296945)

GKR and CO (BID ID -3295101)

Moulya Builders (BID ID -3302189)

PRACHANIVA CONSTRUCTIONS (BID ID -3296574)

M/S Suresh Raju (BID ID -3293953)

VARGHESECHACKO AND CO (BID ID -3302212)