GE/CHM-44/2023-2024 SPECIAL REPAIR TO MD ACCN IN SECTOR C, E AND OTHER MINOR WORKS UNDER AGE B/R III AT CHANDIMANDIR

Amount

Taking down chowkats or frame not exc. 1.5 sqm with shutters, without taking off shutters from the frame, complete all as specified and directed.

Taking down chowkats or frame exc. 1.5 sqm and n exc 4 Sqm with shutters, without taking off shutters from the frame, complete all as specified and directed.

Taking down shutter of any description exc 1 Sqm but n.exc 2 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 1Sqm but not exceeding 2sqm each including stacking at location as directed by Engineer-in-Charge for refixing in same opening(s) after rescuring or easing, adusting, welding, etc., complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden, metel frames including punching or drilling out glazing pins/spring clips complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness. (Below or above ground level) complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description in any position not otherwise specifically provided for, complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors, beams, staircases, landing, chajjas and similar suspended work, complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded or laid bedded pointed in any mortar, all as specified.

Taking down cement plaster / terrazo of any description from brick walls or concrete surfaces including raking out joints, hacking out for key, scrubbing down with water complete, all as specified and directed.

Dismantling floor hearth or wall tilling including cement mortar bedding, complete as specified and directed.

Taking up or down steel tubing and connections 15mm bore, complete all as specified and directed.

Taking up or down steel tubing and connections 20mm bore ,complete all as specified and directed.

Taking down rain water pipes of any type including all fittings , complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, all as directed.

Dismantling of existing brick tiles or terracing tiles single layer on roof grouted in cement mortar including mud phuska as in roof of any thickness including plastering and leeping etc , removing any type of existing treatment ,complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete, all as specified & directed.

Plain cement concrete 1:7:12 type F-2 using 40mm graded brick coarse aggregate as in sunken floor filling and mass concrete complete all as specified & directed.

Plain cement concrete type B-1, 1:2:4 using (20 mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, parapets and railings upto 60 cm in height, copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including the use of forms or moulds with plain faces complete all as specified and directed.

Material and labour for 50mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight, all as specified & directed by Engineer-in-charge.

Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick bedding layer in CM 1:6, complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick bedding layer in CM 1:6, complete all as specified and directed.

Glazed ceramic coloured printed tiles 7 mm thick of size 300mm x 450mm/350mm x 250mm as in skirting, dado or wall, set and jointed in neat cement slurry and grouted in white cement complete over and including 10 mm thick bedding layer in CM 1:4 complete, all as specified and directed.

14-16mm thick Baroda green marble (of any type & shade as approved), as on steps, jambs, cooking platform, counter slab etc (length and width as ordered by GE in one piece) best quality machine cut and jointed with grey cement slurry and pointed in white cement mixed with pigment (1:2) to match the shade of slab laid over and including 15mm thick screed bed in cement mortar 1:4 including nosing at edges , dismantling of existing tiles ,complete all as specified and directed.

Machine cut kota stone slab flooring 18-20mm thick (one piece) for staircase landing , treads steps, etc laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, laid over and including 10mm screed layer in cement mortar 1:4, cutting, rubbing, grinding and polishing upto granite finish, complete all as specified.

All as per serial item No 26 herein before but in skirting, riser of staircases etc over and including 10mm thick rendering in cement mortar 1:4

Making holes into or through concrete slabs/ stone slabs 150 mm thick for 25mm dia pipe as in cooking plateform, incl making good the surface, complete all as specified and directed.

Reinforced cement concrete, 1:2:4 (nominal mix, type B-0, using 12.5mm graded crushed stone aggregate) as in slabs supported on walls, beams etc, shelves and the like complete, all as specified and directed .

Reinforced cement concrete, 1:2:4 (nominal mix, type B-0, using 12.5mm graded crushed stone aggregate) as in chajja etc, shelves and the like complete, all as specified and directed .

Reinforced cement concrete 1:2:4 (nominal mix, type B-0, using 12.5mm graded crushed stone aggregate) as in beams, lintels over 1.5 metre span and the like complete all as specified and directed (reinforcement shall be measured and paid for separately).

Mild steel TMT bars 10mm dia and over ,cut to length, bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

Mild steel TMT bars 6mm to 8mm dia and over ,cut to length, bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

Form work to flat surfaces of suspended slabs such as roof slab, floor slab, landing, shelves etc not exceeding 200mm thick, including edges in any position, rough finished surfaces, complete all as specified and directed.

Form work to chullah hoods, chajjas and similar items including edges / sides and soffits of lintels etcrough finished surface of concrete flat complete all as specified and directed.

Form work to sides and soffits of floor or roof beams, beam hanunchings, girders, shelves including supports, overhangs etc also splays between floors and beams etc rough finished surface of concrete flat complete all as specified and directed.

Factory made pressed steel frames having profile 125mm x 60mm for doors with one or more rebates made out/fabricated of 1.25 mm thick MS sheet, including necessary fixing lugs, hinges, lock strike plate, thress hold bar/flat etc. complete ,all as specified and directed.

Factory made pressed steel frames having profile 105mm x 60mm for doors with one or more rebates made out/fabricated of 1.25 mm thick MS sheet, including necessary fixing lugs, hinges, lock strike plate, thress hold bar/flat etc. complete, all as specified & directed.

35mm thick flush shutters, solid core costruction, with block board core and plywood face panels, commercial type on both sides as in cupboards, etc. complete all as specified and directed.

35 mm thick second class hard wood glazed and skelton shutters open rebated and prepared to received gauge/ glass etc, edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc complete all as specified and directed.

35 mm thick, factory made, second class hard wood, plain framed hammer marked, panelled shutter (two panel)with lock rail and panel of 9 mm BWP commercial ply both face . The size of rail and stile as per IS : 1003 (Part I) kiln seasoned and chemically pressure treated complete all as specified and directed.

Solid PVC frame (Single Rebated) of size 75mm x 50mm made out of solid PVC foam of 550 density with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed.

Solid PVC frame (Single Rebated) of size 62mm x 32mm made out of solid PVC foam of 550 density with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner , complete all as specified and directed.

Factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

Factory made solid PVC board 20-22 mm thick with PVC leeping pasted at the exposed sides as in kitchen cabinet/ cupboard panell,sag free thermal and electrically insulated, light weight wrap free, impact resistant, fire resistant, termite resistant, chemically resistant and smell free complet,e all as specified and directed.

100 mm size butt hinges medium weight cold rolled mild steel complete, all as specified and directed.

100mm butt hinges , extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed for PVC door, type C-21 complete all as specified and directed.

Continuous (Piano) hinges of size 30mm (width of flap when open) , mild steel ,fixed in repairs, complete all as specified and directed.

100mm hasp and staple,aluminium anodised, wire type, including bolt to hinge plate and fixed with screws, complete all as specified and directed.

125mm hasp and staple,aluminium anodised, wire type, including bolt to hinge plate and fixed with screws, complete all as specified and directed.

200 mm size aluminium , barrel tower bolt of extruded section and fixed complete all as specified and directed.

150 mm size aluminium, barrel tower bolt of extruded section and fixed for PVC door complete all as specified and directed.

150 mm aluminium handles cast type complete all as specified and directed.

250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed,complete all as specified and directed.

300mm MS ordinary rat tail rod pattern spring incl roller plate complete all as specified and directed.

40mm dia cupboard brass knob fixed with nut screw and washer fixed in any position, complete all as specified and directed.

Magnetic catcher 40mm x 25mm size, PVC body with magnet amd MS plate and fixed with standard steel screws, complete all as specified and directed.

Cutting holes in brick walls built in cement mortar (exc. half brick but not exc. one brick ) and making good the surfaces by cement mortar (1:3) or PCC (1:2:4) type B-1, complete all as specified and directed.

Cutting opening through brick wall built in cement mortar for doors, windows, and other openings or enlarging existing openings, converting window to door opening etc removing and rubbish n.exc 50 metre and making good complete all as specified and directed.

Factory made steel window box type with side hung shutters including box type hinges and one shop coat of red oxide primer, 125mm steel handle-02 Nos mild steel ISI marked tower bolt 125mm size (minimum 2 for each shutter) complete with glazing bars, dovetailed or welded fixed with and including MS flat of suitable size for fixing grills and guards bars etc , fixed in repairs, complete all as specified.

Factory made steel window box type with side hung shutters including box type hinges and one shop coat of red oxide primer, 125mm steel handle-02 Nos mild steel ISI marked tower bolt 125mm size (minimum 2 for each shutter) complete without glazing bars, dovetailed or welded,fixed in repairs, complete all as specified.

Factory made box type steel ventilators, openable with side hung shutters with box type hinges including one shop coat of red oxide primer, hinges, tower bolts 100 mm, steel handles and steel peg stay complete without glazing bars devetailed or welded, fixed in repairs, complete all as specified and directed.

4mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty (or beading) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

Galvanized MS wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm, fixed as in repairs, complete all as specified and directed.

4mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty (or beading) in square n.exc 0.5 Sqm in each pane, complete all as specified and directed.

Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings, framework of water tanks, framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc and similar work conforming to Fe.290.Gde-E-165, all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of red oxide, complete all as specified and directed.

Preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint , complete all as specified and directed.

Preparation of old steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint , complete all as specified and directed.

Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and directed.

Preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint , complete all as specified and directed.

Brick work with sub class ‘B’ bricks, old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

Dubbing out average 15mm thick on irregular face of walls /RCC surfaces in cement mortar (1:4), complete all as specified and directed.

Rendering 5mm thick in CM 1:3 on fair faces of concrete/brick surfaces as in ceilings , facia, chajja, etc finished fair and smooth, complete all as specified and directed.

Rendering 15mm thick in Cement and Sand mortar 1:6 over fair faces of brick / concrete ,finished even and smooth without using extra cement, complete all as specified and directed.

Rendering 15mm thick in Cement and Sand mortar 1:4 over fair faces of brick / concrete ,finished even and smooth without using extra cement, complete all as specified and directed.

Rendering 15mm thick in Cement and Sand mortar 1:4 over fair faces of brick / concrete ,finished even and smooth without using extra cement, inclunding using water proofing compound complete all as specified. Note : WPC shall be measured and paid separately.

Preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over and including a coat of primer complete all as specified and directed.

Preparation of old surfaces of walls and applying two coats of oil bound distemper complete, all as specified and directed.

Three coats of white wash on ceiling surfaces including preparation of new plastered surfaces complete all as specified and directed

Two coats of white wash on old surfaces of wall including preparation of surfaces, complete all as specified and directed

Two coats of white wash on old ceiling surfaces including preparation of surfaces, complete all as specified and directed

Preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer , complete all as specified and directed.

Preparation of old decorated surfaces of walls by removing existing finishes and applying two coats of cement base paint , complete all as specified and directed.

Water proofing treatment to sunken portion and adjoining walls of kitchen, WC, Bath & Toilet, etc complete all as specified as under:- (a) 15 mm plaster in cement mortar (1:3) mixed with water proofing compound as per manufacturer’s instructions after roughning and cleaning the surface . (b) Curing the sunken portion with water minimum for 48 hours by ponding. (c)Applying 3mm thick APP membranne with bitumen by torch application to the treated sunken surface over a coat of primer as per manufacturers instructions. (d) Joints/Traps/WC/soil pipes shall be properly sealed with approved sealing compound .

40mm thick brick tiles , joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on and including 20mm thick screed bed or bedding layer in CM(1:4), complete all as specified and directed.

All as per serial item No 87 herein before but except brick tiles .

Cast iron nahani traps 100mm dia with grating including jointing to waste pipe with run led jointed and setting/fixed in cement concrete type B-1 1:2:4 fixed as in repair complete all as specified and directed.

Wash hand basin, vitreous china, flat back, white of size 550 x 400 mm, waste coupling, angle brackets, PVC connection 15mm size, 450mm long, PVC waste pipe, fixed as in repair complete all as specified and directed.

Vitreous China Wash down water closet (pedestal pattern), white with and including PVC seat cover, fixed as in repair complete all as specified and directed.

Vitreous china squatting pan "orissa" pattern, size 580 x 440 mm white, with integral foot rest (excluding flushing cistern and flush pipe) and connecting to trap, fixed as in repair complete all as specified and directed .

PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle and brackets, fixed in repairs. complete all as specified & directed.

sink mixer one hole with swivel casted spout ( wall mounted model), chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs, complete all as specified & directed

Cast iron "P" or "S" trap 100 mm bore, complete all as specified and directed.

PVC connections 15mm size with PTMT nuts of length 450mm, fixed in repairs, all as specified and directed.

Towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 190gms), fixed as in repair complete all as specified and directed.

Towel ring of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 90gms), fixed as in repair complete, all as specified and directed.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide with CP bracket guard and railing 60cm long, fixed as in repairs, complete all as specified and directed.

Grating doom 100mm dia of PTMT, fixed to floor trap with cement mortar 1:3, fixed as in repairs, complete all as specified and directed.

Plate rack of stainless steel sheet 1.0mm thick of size 750mmx 600mm with steel shelves and hanging arrangements for utensil, fixed as in repairs, complete all as specified and directed.

Kitchen sink with drainage board made out of stainless steel sheet 1.0mm thick with plug, washers and CP waste coupling, overall size 915mm x 460mm x 203mm, with bowl of size 405mm x 354mm x 203mm incl fixing cantilever brackets, fixed as in repairs, complete all as specified and directed.

15 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors ,complete all as specified and directed.

Refixing old steel tubing of 15 mm bore and connections in new or old position (walls, ceilings, floors etc.) including cleaning ,complete all as specified and directed.

20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

Refixing old steel tubing of 20 mm bore and connections in new or old position (walls, ceilings, floors etc.) including cleaning, complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc and cutting chases for concealed water tubing & making good, cutting not exc 10 cm girth, in brick walls complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 20mm bore pipe, fixed as in repairs complete all as specified and directed.

Bib taps brass, fancy type, Short body with wall flange, standard chromium plated, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, fixed as in repairs compl complete all as specified and directed.

Bib taps brass, fancy type, long body with wall flange, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Stop valve (concealed type), cast copper alloy, chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Wash hand Basin brass Mixer of chromium plated hot and cold water screwed down for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair, complete all as specified and directed

Chromium plated, fancy type shower rose with swivel joints 125mm dia with arm and fixing to steel pipe 15mm bore, fixed as in repairs, complete all as specified and directed

20mm dia stainless steel curtain rod including fixing fancy types brackets, stops, rollers etc., complete all as specified and directed.

20mm dia anodised aluminium alloy curtain rod including fixing fancy types brackets, stops, rollers etc., fixed in repairs, complete all as specified and directed.

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, complete all as specified and directed.

PVC (SWR) 75mm bore, single socketed in any length as in waste and vent pipewith rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, complete all as specified and directed.

110 mm bore PVC (SWR) bends of any radius complete, all as specified and directed.

75 mm bore PVC (SWR) bends of any radius complete, all as specified and directed.

Raking out joints/ pointing in cement mortar to brick tiles, laid flat on roofs to receive cement concrete including cleaning of surfaces, complete all as specified and directed.

Rendering 20mm thick (average thickness) for levelling of RCC roof slab, finished even and fair in cement mortar (1:4), complete all as specified and directed.

APP based polymeric membrane 3mm thick, minimum weight 3 kg/Sqm , reinforced with polyester non woven fabric (weight not less than 150 gms/sqm) laid on primed surface by torch application on and including bituminous primer @ 0.40 ltrs per square metre ,complete all as specified and directed.

Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surfaces complete all as specified and directed.

Kitchen sink made out of stainless steel sheet 1.0mm thick with plug, washers and CP waste coupling, overall size 495mm x 420mm , with bowl of size 410mm x 330mm x 160mm incl fixing cantilever brackets, fixed as in repairs, complete all as specified and directed.

Supply only integral water proofing compound (ISI Marked) complete all as specified & directed.

Plain cement concrete type C-2, 1:3:6 using 40mm graded crushed stone aggregate as in padding on RCC roofs finished fair and even complete all as specified and directed.

500 Litres capacity Rotational moulded polythene water storage tanks (cylindrical vertical with closed top) double layered hoisted and fixed in position including PTMT ball valve 20mm bore & PTMT tank nipple, etc, fixed as in repairs, complete all as specified and directed.

Float valve/ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed for 20mm bore pipe (minimum weight 210 gms), fixed as in repairs, complete all as specified and directed.

Rolled sections as in main and cross beams, hip and jack rafters,purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates, conforming to Fe-290 Gde E165, all as specified and directed.

Pre-painted galvalume aluminium zinc (AZ-70) coating GI based corrugated steel sheeting 0.50 mm thick any colour having tensile strength 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws etc , including dismantling of old sheet of any description complete all as specified & directed by Engineer-in-charge.

Machine pressed Concrete interlocking paver block, with grey cement and pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over and including 25mm thick sand cushioning , including dismantling of old tiles complete all as specified and directed

Taking down carefully aluminum/copper point wiring on & including hard wood battens, surface conduit and board/blocks etc or through conduits for light , socket or power point ,fan point complete incl fitting such as switches ,sockets, ceiling rose , holder socket, light fitting, regulators and making good disturbed surfaces of wall, floor , ceiling etc and removing materials (other than those for which credit has been given by the contractor) to the MES stores yard for keeping in safe custody complete all as specified and directed.

Point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in existing conduit terminated on and including new modular sunken box and suitable size of frame, cover for mounting switch, socket and regulator fixed on surface flush with wall , comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed. Note : (i) Unit rate is inclusive of making good the disturbed surfaces by provding by wall putty/POP after mason work and finshing to match the original surface and nothing extra shall be paid on this account. (ii)Unit rate is inclusive of cutting chases in wall /foor/PCC for sunken box and making good the disturbed surfaces to match the original and nothing extra shall be paid on this account.

All as per serial item 136 herein before but for one light point controlled by two way switches, complete all as specified and directed

All as per serial item 136 herein before but for socket outlet 3 pin 6 Amps on same board complete all as specified and directed

All as per serial item 136 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed

All as per serial item 136 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor

Switch modular type (ISI marked), single pole, one way 6 Amps, one module (ISI marked), complete all as specified & directed.

Switch modular type (ISI marked), single pole, one way 16 Amps, one module (ISI marked), complete all as specified & directed.

Switch modular type (ISI marked), two way 6 Amps, one module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2/3 pin 6 Amp modular type multi purpose combined two module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2 in 1 pin 6/16 Amp modular type multi purpose combined 2 module (ISI marked), complete all as specified & directed.

Modular switch type stepped fan regulator, single pole, 230 volt one module ,all as specified and directed.

Modular switch type bell push, single pole, 230 volt one module,(ISI marked) all as specified and directed.

Modular white cover plate with frame,3 module, complete all as specified.

Modular white cover plate with frame,4 module, complete all as specified.

Modular white cover plate with frame,6 module, complete all as specified.

Electric Bell, AC, 230 volts, single pole all as specified and directed by Engineer-in-charge.

Modular metal flush box,3 module, complete all as specified.

Modular metal flush box,4 module, complete all as specified.

Modular metal flush box,6 module, complete all as specified.

Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge.

Lamp holder, PVC/Polycarbonate type with back plate angular type fixed on wall suitable for batten fitting ,complete all as specified and directed.

LED bulb 9W, B 22 type, complete all as specified.

LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete, fixed in repairs, all as specified..

LED bulk head lights 1x 9W/ 1x 10 W, 220V, including LED driver, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete, fixed in repairs, all as specified..

Taking down and refixing only LED lights fitting 1x 20W, 220V, AC after cleaning and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete,all as specified..

LED lights fitting 1x 10W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete, fixed in repairs, all as specified..

Taking down carefully old copper or aluminium sub main wiring of any Nos of wiring and size with earth wire on wooden batten/ surface conduit/ casing- capping complete with its all accessories and making good disturbed surfaces of wall , floors etc complete all as specified and directed.

Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 6 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 6 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 6 sqmm and one single core of 06 sqmm cable shall be considered as 1 running metre. (ii) PVC conduit and cutting chases will be measured and paid separtely (iii) colour code shall be Red for phase, Black for neutral and green for earth

Disconnecting the power supply and taking down carefully by unscrewing from boards fittings and fixtures such as DBs, Junction Box, Panels of any size complete with all MCCB's ,MCB's etc and removing from site, Complete all as specified and directed .

MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, 08 way SPN with 200 Amps busbar 240V completed all as specified and directed.

MCB ,SP , 240 volt, 6Amps to 32Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

MCB, SPN , 240 volt, 40 to 63Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

Cutting openings, through brick walls in round shape , for 300mm dia exhaust fan and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required including finishing and matching the disturbed surface and removing surplus unserviceable bricks, hard-core, etc. from site and rubbish complete all as specified & directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers, , all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, burried directly in ground vertically to a depth not less than 2.25m below normal ground level, with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI light grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of presast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Sch Part-I (2009), complete including dismantling of old earthing, all as specified and directed. Note(s) :- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) unit rate including protection pipe and GI wire 4.00mm dia from top to earth plate upto 7.5 meter

KUNDRA CONSTRUCTIONS

Gunjan and Gunjan Associates

M/S Dashmesh Enterprises

M/s Hari Om Engineer and Contractor