CA NO CWE/FZR-56/2019-20 SPECIAL REPAIR TO BLDG NO E-31 (FAMILY WING) OF 159 GH UNDER GE (EAST) FEROZEPUR CANTT

Amount

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegetation, complete all as specified.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified.

M&L for screeding 10 mm thick in cement mortar (1:4) on brick/concrete surfaces of roof, finished even and smooth without using extra cement, complete all as specified.

S&F 150 micron thick (transparent) polythene film with 150mm end & side laps, laid over a coat of bitumen primer @ 0.30 kg to 0.50 kg per sqm, bonded with a coat of 80/100 industrial bitumen @ 1.20 Kg/sqm and laid on roof, complete all as specified.

M&L 80 mm thick average, consolidated thickness, mud phuska on flat roofs,including 25 mm thick mud plaster and 3 mm thick leeping plaster, complete all as specified.

S&F 40 mm thick brick tiles laid over a layer of 25mm thick mud mortar and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement, complete all as specified.

All as per item No 6 herein before but using old brick tiles retrieved from dismantling (Item No 01 hereinbefore) including cleaning and removal of mortar from tiles, complete all as specified.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level), complete all as specified.

M&L Cement concrete (1:2:4) type B-0 (12.5 mm graded stone aggregate) as in kerbs, mud stops, round or chamfered on edges etc including form work, weathering, slightly rounded or chamfered complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified.

M&L for cement concrete chequered tiles 20cm x 20cm x 25mm thick, set jointed and pointed in neat cement slurry in floors with grey cement and pigments to match, including 15 mm thick screed in CM 1:6, complete all as specified.

Demolition of reinforced cement concrete in any position not described else where, complete all as specified.

M&L reinforced cement concrete (1:2:4) type B-1 (20 mm graded stone aggregate) as in slab supported to walls, beams, roofs, landings, balconies, canopies and shelves, complete all as specified.

S&F Mild steel TMT bars 10 mm dia and over as in reinforcement cut to length bent to shape required including cranking, hooking at ends and binding with mild steel wire (annealed) not less than 0.9mm dia FE-500/550 confirming to IS-1786-1985 all as specified.

M&L for use & waste wooden form work (rough finished surfaces ) as in slab supported to walls, beams, roofs, landings, balconies, canopies and shelves including edges, supports overhangs, etc also splays between floors and beams, floor/roof slab, landings and similar work n. exc 200mm thick, complete all as specified

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc, complete all as specified.

M&L for Rendering 10 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M&L for Rendering 15 mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M&L Rendering 5 mm thick in cement mortar (1:3) on ceiling concrete surfaces finished even and smooth without using extra cement, complete all as specified.

M&L for Glazed ceramic tiles, coloured ( colour & shade as approved), of size 300x200x7 mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry and pointed in white cement with pigment to match the colour of tiles, laid over & including 10 mm thick rendering in cement mortar (1:4), complete all as specified.

M&L for Non skid Ceramic coloured ( colour and shade as approved) tiles,any shape, 7mm to 8 mm thick area of each tile exc. 0.11 sqm and not exc 0.18 sqm as in flooring set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles laid over & including 15 mm thick screed in cement mortar (1:6), complete all as specified.

M&L for Vitrified tiles light colour, (Square/rectangular) 10 mm thick area of each tile n.exc. 0.36 sqm as in flooring set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles laid over & including 15 mm thick screed bed in cement mortar (1:6), complete all as specified.

All as per item No 22 herein before but as in skirting including backing coat 10mm thick in cement mortar (1:4), complete all as specified.

M&L for Taking down wooden/steel chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts,making good jambs with plaster in CM (1:4) to match with existing finish, complete all as specified.

All as per item No 24 herein before but size exceeding 1.5 Square metre and not exceeding 4 Square metre each, complete all as specified.

S&F aluminium anodised sections as in doors/windows/partions,channel, rollers,aluminium anodised snap beading for fixing glass panes etc, cleats any size, thickness, including inserted to floor/wall, fixing with rawl plugs, steel screws etc, complete all as specified. Note:- (i) Glass pane will be measured and paid separately. (ii) The quoted rates inclusive of cost of rubber beading however it will not be weighed and paid seprately.

S&F anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc, complete all as specified.

S&F anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, complete all as specified

S&F in repair Gypsum Board 12mm thick in ceiling fixed with screw of size 60cmx60cm placed in ceiling including anodised aluminium snap grid frame work of size 605mmx605mm for false ceiling including hanging arrangements, complete all as specified.

M&L Preparation of newly plastered surfaces of ceiling & applying three coats of white wash, complete all as specified.

M&L Preparation of old decorated plastered or unplastered by brooming down with steel wire brush, scarping down smoke soot, mould,moss and efflorescent salts and trading oil, greasy spots and applying two coat of white wash on ceiling including cornices, pillasters etc, complete all as specified and as directed.

M&L Preparation of newly plastered surfaces and applying two coats of oil bound distemper, over a coat of 3 mm thick wall care putty, and a coat of primer, complete all as specified and as directed.

M&L Preparation of old decorated plastered or unplastered by brooming down with steel wire brush, scraping down smoke soot, mould, moss and efflorescent salts and trading oil, greasy spots and applying two coats of oil bound distemper over of chalk whitening and primer, complete all as specified and as directed.

M&L Preparation of new plastered surfaces walls etc and applying two coats of cement base paint, over a coat of 3 mm thick wall care putty, and a coat of primer, complete all as specified and as directed.

M&L Preparation of old plastered surfaces of walls after complete removal of existing treatment and applying two coats of cement base paint over a coat of primer complete all as specified.

M&L for Kota stone slabs, 20mm to 25mm thick, machine cut as in flooring of size not less than 0.25 Square metre each, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab laid over & including screed bed of 20 mm thick in cement mortar (1:6) including rubbing, cutting and polishing (mirror type) complete all as specified.

S&F Kota stone slabs, 20 mm thick, machine cut as in shelf, skirting,steps,dado,pillars etc, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab laid over & including rendering coat of 15 mm thick in cement mortar (1:4) including rubbing, cutting and polishing ,complete all as specified.

S&F Factory made solid PVC door frame (having density not less than 600 kg/cum) of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube, complete all as specified in MES Schedule Part-I (2009), including making good jambs in CM(1:4) with finishes to match with existing, complete all as per specification & shown in drawing.

S&F Factory made solid panel PVC door shutter 30 mm thick (having density not less than 600 kg/cum) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site, complete all as per specification in MES Schedule Part-I (2009) & shown in drawing.

S&F PTMT tower bolts, 200 mm long and fixed with steel screws complete all as specified.

S&F PTMT butt hinges,100 mm long and fixed with steel screws complete all as specified.

S&F PTMT handle,125 mm long and fixed with steel screws complete all as specified.

S&F in repair, Galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceiling, complete all as specified.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in flag post, floors and all other similar works & including 15 mm thick screed in cement mortar (1:4) laid over, complete all as specified.

S&F 140 mm floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed.

M&L tubular Towel Rail 60cm long 'D' type between flanges of aluminium anodized 20mm dia fixed to walls, complete all as specified.

S&F 4 lever mild steel mortice lock,vertical type size 100 mm complete all as specified.

Taking down carefully existing copper/alumimium point wiring for light/fan/socket out let points complete with fitting and fixtures, battens, wire etc and making good the disturbed surfaces of walls and ceilings, complete all as specified.

Taking down unserviceable main switches, electric metres and distribution boards single phase, complete all as specified.

Taking down carefully old unserviceable sub main wiring and making good disturbed sufaces and matching with existing complete all as directed and specified.

S&F Point wiring complete with 1100 volts grade PVC FRLS insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through & including PVC rigid concealed conduit, medium grade of suitable size (not less than 20mm dia) duly ISI marked with all accessories such as bends, reducers, spacers, saddles, junction boxes, bakelite sheets, sizes for mounting switch/sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS copper conductor, insulated, unsheathed,stranded (Green colour) connected to common earth dolly complete all as specified for following:- (a) One light/fan/bell/exhaust point controlled by one single pole one way switch.

(b) One 3 pin 5 Amp socket outlet point controlled by one switch on same board.

(c) One 3 pin 5 Amp socket outlet point controlled by one switch on Independent board .

All as per item 51 above, but one switch socket outlet multi purpose, 3 pin, 15 Amps, point to be controlled by one switch and wiring with 2.5 Sqmm PVC FRLS cable, insulated, stranded, unsheathed copper conductor on Independent board with continuous earth wire of size 2.5 sqmm, PVC copper conductor, insulated, unsheathed, stranded, complete all as specified.

S&F Switch, piano, flush type, single pole one way, 5 Amps, ISI marked,complete all as specified.

S&F Switch piano flush button type 15 Amps, single pole, one way,ISI marked, complete all as specified.

S&F Socket outlet,2 in 1, 5 pin, 5 Amp, piano flush type,ISI marked, complete all as specified.

S&F Socket outlet 2 in 1, 6 pin,5 Amp and 15 Amp, piano flush type, ISI marked, complete all as specified.

S&F Ceiling rose, surface type, backelite 65mmx50mm, 3 terminals complete all as specified.

S&F Lamp holder, insulated body, threaded dome pattern, suitable for bracket/batten fittings, complete all as specified.

S&F LED bulb of 10 watts, complete all as specified.

S&F in repair of regular batten for LED 18W indoor decorative batten with extruded aluminium housing & Opal diffuser IP-20 fixed to walls/ ceiling etc complete including LED tube 18 W, complete all as specified.

S&F 20W suspended architectural LED flat luminaire soft light and glare free symmetrical illumination (with continuous mounting end cap) hanging light, complete all as specified.

S&F 36 Watts recess and surface mounting LED flat panel 2'x2' made of CRCA sheet duly powder coated with high efficient LEDs and glare free full opal diffuser IP-20, complete all as specified.

S&F in repairs bldg security light LED fittings 25 watts complete with all accessories like lamp, bracket of not exc 1.2 metre 25 mm GI light grade tubing & bent at middle to shape by 120 degree from vertical du;ly painted with two coats of aluminium paint with mild steel clamps, nuts & bolts,sleek pressure die cast aluminium housing heat resistant glass IP-65 protection, cable insulated and PVC sheathed copper conductor multi stranded and connecting to conductor and testing, complete all as specified.

S&F in repair Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet,powder coated, SPN DB with 200 Amps rated bus bar, 8 way, FP-42 protection surface mounting, 240 volts, dust and vermin proof, suitable for incorporation of MCCBs duly concealled in wall, factory made,including making good disturbed surfaces with matching colour, complete all as specified.

S&F in repair Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet, powder coated, concealed in wall, TPN DB with 200 Amps rated bus bar, 4 way, 415 volts, vertical type, dust and vermin proof,suitable for incorporation of MCBs duly concealled in wall, factory made,including making good distrubbed surfaces with matching colour, complete all as specified.

S&F in repairs Bell buzzer single phase 220/240 volts, complete all as specified.

S&F bell push Switch, 5 Amps, ISI marked, complete all as specified.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan, complete all as specified.

S&F in repairs stepped type electronic fan regulator for ceiling fan 1200/1400mm size, 230 volts, 6 Amps, complete all as specified.

S&F of MCCB Thermal based release adjustable type 4 pole 63 Amps 50 Hz 415 Volts with rupturing capacity 16 KA including testing, complete all as specified and as directed.

S&F of MCCB Thermal based release adjustable type 4 pole 100 Amps 50 Hz 415 Volts with rupturing capacity 16 KA including testing, complete all as specified and as directed.

S&F of MCCB Thermal based release adjustable type 4 pole 125 Amps 50 Hz 415 Volts with rupturing capacity 16 KA including testing, complete all as specified and as directed.

S&F in repairs MCB, SPN, 40 Amps, 240 volts 10KA duly ISI marked, complete all as specified.

S&F in repairs MCB, single pole, 240 Volt, 6 to 32 Amps, 10 KA complete all as specified.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB MCB 20 Amps, complete all as specified.

S&F in repairs for sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable FRLS 2x6 Sqmm single core 650/1100 V, drawn through & including rigid PVC rigid conduit 25 mm dia including continuous earth wire of size 1x6 sqmm, PVC insulated and unsheathed cable copper stranded conductor (green colour), complete all as specified. NOTE:- Two runs of cable, 1 run of earth wire & one run of PVC conduit shall be measured as one length.

S&F in repairs for sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable FRLS 2x10 Sqmm single core 650/1100 V, drawn through & including rigid PVC rigid conduit 25 mm dia including continuous earth wire of size 1x10 sqmm, PVC insulated and unsheathed cable copper stranded conductor (green colour), complete all as specified. NOTE:- Two runs of cable, 1 run of earth wire & one run of PVC conduit shall be measured as one length.

M&L Earthing as in repairs complete, all as shown on electrical plate No 3 of MES schedule part-I , as in repairs and as specified including the following :- (i) Galvanised steel earth plate of size 60cmsx60cmsx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth not less than 1.50 metre below normal ground level.(ii) Earth plate surrounded by and packed with char-coal and common salt in alternative layers (n.exc 15cms each layer).(iii) 4 mm dia (8 SWG) G.I earth wire from earth plate to main switch board including necessary GI bolts, nuts check nuts, washers, thimbles etc.(iv) 15 mm bore light grade, GI pipe for protection to earth-strip.(v) 20mm bore, medium grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horizontally to the earth pit. (vi) 50mm thick pre-cast cover of cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate and MS angle iron 25x25x3mm frame including two coats of painting over a coat of red oxide to exposed steel surfaces.(vii) Excavation in soft/loose soil, returning filling & removal of surplus soil to a distance upto 50 metre as directed.

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire, complete all as specified.

S&F heavy duty, 900 RPM Exhaust fan AC single phase 230/240 Volts of 300mm sweep with louver plastic body, including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection, complete all as specified.

Cutting hole making good, the disturbed surface, grouting nuts & bolts for fixing of exhaust fans, complete all as specified.

S&F Mild steel galvanised pipe, light grade, 50 mm nominal bore for passing of cable, fixed to poles/walls, laid under floor/road crossings, complete with and including clamps socket & elbow etc including taking down old pipe, complete all as specified.

S&F as in repairs XLPE insulated, armoured,1100 volts grade, heavy duty cable of size 50 Sqmm nominal cross section, 4 core, flat or circular, PVC FRLS insulated aluminium conductor, served with inner sheathing of galvanized steel wire or tape and over-all PVC FRLS sheathed in service connections, laid in trenches, duct, through pipe, in floor, on pole including jointing and testing, complete all as specified .

S&F as in repairs XLPE insulated, armoured,1100 volts grade, heavy duty cable of size 35 Sqmm nominal cross section, 4 core, flat or circular, PVC FRLS insulated aluminium conductor, served with inner sheathing of galvanized steel wire or tape and over-all PVC FRLS sheathed in service connections, laid in trenches, duct, through pipe, in floor, on pole including jointing and testing, complete all as specified .

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and not exc 10 Sqm on plan, for laying of cable and getting out,compete all as specified.

M&L Dry and clean fine sand for cable cushioning to underground cable protection, complete all as specified. (Excavation and earth work measured separately). Note- Punned down thickness shall be measured.

S&F in repair Cover to underground cable with one layer of bricks using sub class ‘B’ bricks (old size) laid flat across the cable complete all as specified. (Excavation and earth work measured separately.

Returning, filling in, earth including spreading, leveling watering and well ramming in layers each not exceeding 25cm thick each layer, complete all as specified.

Removal of surplus soil to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.5 metre above the starting point complete all as specified.

M/s Sanjiv Kumar

Kissan contractor and engg works

S S BUILDERS

M/s Mukand Lal Khanna

M/s S B Construction Company

M/S Yashpaul Gulati

M/s Bansi Lal