PROVISION OF STORE ROOM IN PW DIVISION AREA AT INF SCHOOL MHOW

Amount

Excavating over areas , n exc. 1.50m deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches n exc. 1.50 m wide and n exc. 1.50m depth: for foundation, etc or for shafts,wells cesspits, manholes, pier holes, etc n exc. 10 sqm on plan & n exc. 1.50m in depth & getting out in hard/dence soil complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass complete all as specified and directed.

Formwork surfaced to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter (rough finished) complete all as specified and directed.

M&L for RCC design mix M-25 (20mm graded aggregate) in foundation, footings, plinth protection and similer RCC works complete all as specified and directed.

Formwork to surfaces of concrete to sides of concrete flat or curves sides of pillers, posts, struts,piers,columns and stanchions (rough finished) complete all as specified and directed.

M&L for RCC design mix M-25 (20mm graded aggregate) in coloumns,pillers,piers,posts and struts complete all as specified and directed.

Form work to sides and soffits of floor or roof beams haunching, lintel, coloumn, cantilevers shelves includig supported over hangs etc with rough finished flat surfaces of concrete complete all as specified and directed.

M&L for RCC design mix M-25 (20mm garded aggregate) as in Beams,Cantilevers.brussumenrs,lintels over than 1.50 Span complete all as specified and directed.

Formwork to sides and soffits of slab such as roof slab,floor slab,landing and similer work,etc not exceeding 200mm thick with rough fnished surface of concrete flat complete all as specified and directed.

M&L for RCC design mix M-25 (20mm graded aggregate) as in slab supported on wall , landings, beams canopies, deck slabs and shelves etc complete all as specified and directed.

M&L for 10mm dia and over mild steel TMT bars cut to length bent to shapes as required including bending cranking and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for 6mm to 8mm dia and over mild steel TMT bars cut to length bent to shapes as required including bending cranking and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

All as per item No 12.00 above but 5 mm to 10 mm dia as in Stirrups,spaces & binders complete all as specified and as directed.

M&L for brick work with fly ash brick with using modular size brick, straight or cured on plan exc 6m mean radiuos built cement mortar 1:6 complete complete all as specified and directed.

M&L for moorum/Red bajri filling in floor or paving laid in layers n.exc 15cm thick spread,levelled and rammed including watering complete all as specified and directed.

Removing excavated material exc. 50m but n exc. 500 m and depositing where directed complete all as specified and directed.

M&L for broken stone or boulder hardcore gauge n exc. 63mm, deposited spread and levelled in layers n exc. 15mm thick, watered and rammed to true surface complete all as specified and directed.

M&L for 100 mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in sub-base, to floor and foothpath etc complete all as specified and directed.

M&L for PCC 40mm thick cement concrete type B-0 1:2:4 (using 20mm graded stone aggregate) as in floor as per leveling course complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 20 mm thick (+ 2mm) thick of with 58cm x 58cm in size (or nearest size as available in the market) laid over and including 15mm thick screed bed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing to mirror finish complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 20 mm thick in riser of steps,skirting,dado and piller laid over cement screed and joined and over and including 10mm thick rendering in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing to mirror finish complete all as specified and directed.

M&L for rendering 15 mm thick on unfair faces of brick work or concrete surfaces in cement mortar 1:6 for finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for rendering 15 mm thick on unfair faces of brick work or concrete surfaces in cement mortar 1:4 using using water proofing compound (200ml by weignt per bag cement) finished even and smooth without using extra cement complete all as specified and directed. Note: WPC will be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggragate) as in plinth protection and paving finishing concrete surfaces even and smooth without using extra cement complete all as specified and directed.

S&F powder coating anodised aluminium ventilator (Louvers type) with louvers glass and glass stay,setion weighing 0.55Kg/m incl necessary joining cleats, glazing clips for fixing of wiremesh,rubber neoprene packing,anodised aluminium snap beading screws etc.(minimum thickness of powder coating 50micron) complete all as specified and directed.

S&F factory made steel window , with side hung shutter including projecting hinges with steel handle, stay complete devetailed or welded complete all as specified and directed.

S&F factory made steel window, with side hung shutter including projecting hinges with steel handle, stay complete without glazing bar and guard bar devetailed or welded complete all as specified and directed.

M&L for painting with two coats of synthetic enamel paint to steel surfaces of any description over 10cm width or girth on untreated steel surfaces over a coat of red oxide primer after preparation of surfaces complete all as specified and directed.

S&F framed work such as grills,grating etc with ends of bars shoulders and/or rivited/welded in guard bars and similer works confirming to FE.290,Gde-E-165 complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:3 as on concrete surfaces in ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&Lfor preperation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for applying evently a tack coat of industrial bitumen 25/85 at the rate of 1.20Kg per Sqm including cleaning surfaces over bituminous primer complete all as specified and directed.

M&L for APP based polymeric mebrain minimum weighing 3Kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt on not less than150ms/Sqm) land on priimed surface by forced torch application complete all as specified and directed.

M&L for two coats of bitumen based aluminium painting over a coat of primer on water proofing treatment with preparation of surfaces as on non assesable area complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of wall care putty wall complete all as specified and directed. Note: Putty shall be measured and paid separatly.

M&L for 1 mm thick white cement based wall care putty wherever required complete all as specified and directed.

M&L for preparation of newly plastered surface of wall, pilasters, cornices etc and treatemnet apply two coats of Anti fungal weather coat acrylic emulsion paint over a coat of primer (X2) complete all as specified and directed. Make : (a) Asian (Apex ultima) / Berger weather coat all gaurd / ICI Dulex (Weather sheild Max) / Nerolac (Excel total) Make of primer : Asian / Berger/ ICI Dulex /Nerolac Note : (i) Each stages i.e Preparation primer application, first coat and second coat of paint will be passed by Engr-in-Charge (ii) Written warrenty for four years after completion of work is required to be funished by the contractor.

S&F in steel rolling shutters thickness of lath in 1.25mm with ball bearing,as specified including top cover,anchoring rod,hesp and staple and one shop coat of primer ercted in position as indicated,complete push pull or manual type and including safety lever locks mild steel with 4 levers for rolling complete all as specified and directed.

M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC FRLS concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches and blank plates, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :-

(a) One ligh/Exhaust Fan point controlled by one switch

(b) One 5amps socket out let point controlled by one switch on same board with other switches.

(c) One 5amps socket out let point on independent board controlled by one switch.

S&F switch piano flush button single pole one way 6 Amp 240 volt complete all as specified and directed.

S&F socket outlet flush type 5 pin, 6 amps, 230 volts complete all as specified and directed.

S&F ceiling rose surface bakelite three terminal complete all as specified and directed.

S&F integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 /Bajaj cat Pt No. BCLSB 18WH or equivalent in Wipro as approved by GE.

S&F LED street light fittings 1x35 Watt, 5700K complete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 /66protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible copper cable complete all as specified and directed. Make:- Havells Cat No.LHEXAYP7PN6K030 / Crompton Cat No. LSTO-25-CDL /Bajaj Cat No. BCLST 25W LED IV2

S&F double door SPN DBs eight way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed by Engr-in-Charge.

S&F MCB TPN 40 to 100 amps 10 KA, c-series including connection with suitable size aluminium/copper lugs complete all as specified and directed by Engr-in-Charge.

S&F MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-in-Charge.

S&F exhaust fan steel body AC single phase, 230 V of size 300 mm sweep ventil air DSP green type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall or fixing in aluminium fabricated windows including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base and finishing compelte all as specified and directed. Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in quoted rate.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cmx 6.3 mm thick buried directly in ground ( earth pit not less than 2.25 meter deep below ground level) with the top edge of the earth plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate No.5 of MES SSR parts-I and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of PCC earth chamber in mix 1:3:6 type C-1 with 40 mm thick RCC 1:2:4 type B-J cover reinforced with 8mm dia MS TMT bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia GI light grade and 15mm dia light grade pipe for earth lead protection and testing on completion, complete all as specified and directed.

Supply and laying & testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size 4 core x 16 Sqmm complete all as specified and directed

Excavation in trenches n exc. 1.50m wide & n exc. 1.50m in depth for foundation ,laying of cable or pipe ( where provide for protection of cable or fixing poles and stay and getting out in soft/loose soil including trimming the sides and forming bottom surfaces to required levels complete all as specified and directed.

Returning, filling in trenches in soft/loose soil in layers n exc. 25 cm after laying of cables including spreading, levelling, and well ramming complete all as specified and directed.

Removing surplus excavated soil to a distance n exc. 50m and depositing where directed at a level n exc.1.50m high from the starting point complete all as specified and directed.

M&L for local sand cushioning with dry and clean sand over and under the under ground cable in trenches , ducts for cable protection complete all as specified and directed. Note: Punned thickness shall be measured.

M&L for bricks slightly over burnt (kiln burnt) , modular bricks , best quality, locally available , laid flat, dry, laid in trenches along the length of cable transvarsally with width equal to length of brick for cable protection complete all as specified and directed.

S&F galvanised iron pipe 'light Grade' 40 mm in trenches , under floors, roads, along poles for protection of cables with all necessary fittings, including sealing ends complete all as specified and directed.

J B CONSTRUCTION AND DEVLOPERS (BID ID -3125147)

M/s Narendra kumar Agrawal (BID ID -3113862)

M/S UnitedConstruction (BID ID -3112887)

sunway associates (BID ID -3113886)

Sudarshan Associates (BID ID -3125315)