Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Infra Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹38.9 LAccepted-AOC 29 GANDHI NAGAR VETERINARY COLLEGE ROAD BIKANER 334001 RAJ | BIKANER | RAJASTHAN | 334001 | L1 | Accepted-AOC Due to lowest bidder | |
| 2 | L2₹42.8 L+₹3.4 L (8.71%)Rejected-Finance PEMASAR ROAD WARD NO 04 UDASAR BIKANER RAJ 334001 | BIKANER | BIKANER | RAJASTHAN | 334001 | L2 | Rejected-Finance Due to not lowest bidder |
Tender Value
₹49.9 L
EMD Value
₹99,840
Closing Date
4 Dec 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE (N) BIKANER
GE (N) BIKANER RAJASTHAN 334001
PROVN OF GD ROOM ALONGWITH SENTRY TOWER AND TOILET AND SPL REPAIR TO OR BATHROOMS AND TOILETS AT MIL STN BIKANER UNDER GE N BIKANER
2023_MES_620785_2
GE (N) BKN-TOKEN/58/2023-24
Open Tender
Miscellaneous Works
Item Rate
270 days
GE (N) BIKANER
As per tender documents
6 documents required · 6 mandatory
₹500
GE (N) BIKANER
₹99,840
Yes
25 Jan 2024
14 Nov 2023
11 Dec 2023
14 Nov 2023
4 Dec 2023
22 Nov 2023
Amount
Dismantling Asbestos cement Corrugated sheets in roof covering including ridges complete all as specified and directed by Engineer-in Charge.
Taking down cement plaster, any description on brick or stone or cement concrete walls including any tiles and raking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engineer-in Charge.
Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), all as specified and directed by Engineer-in Charge.
Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, and refixing in the same opening after rescuring easing and adjustment, complete all as specified and directed by Engineer-in Charge.
Demolition of brick/stone masonry built in CM. complete all as specified and directed by Engineer-in Charge.
Demolition of cement concrete (unreinforced) In ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in Charge.
Dismantling floor hearth or wall terrazo or tiles in bath, WC and kitchen etc including ceent mortar bedding but not backing removing serviceable tiles to store and rebbinsh off the premises complete all as specified and directed by Engineer-in Charge.
Taking up or down steel tubing 15 mm bore with connections for cleaning for refixing complete all as specified and directed by Engineer-in Charge.
Taking up or down steel tubing 20 mm bore with connections for cleaning for refixing complete all as specified and directed by Engineer-in Charge.
Dismantling cast iron /PVC pipes fixed to walls or laid in trenches in any position of dia upto 100mm complete all as specified and directed by Engineer-in Charge.
Dismantling of Roof tiles of any description or thickness in floor, apron etc laid, bedded and pointed in cement mortar complete all as specified and as directed by Engineer-in-Charge.
Demolition of lime concrete of any description over roof slab complete all as specified and as directed by Engineer-in-Charge..
Dismantling water tanks and removing to store exc 500 ltrs and nexc 1000 ltrs complete all as specified and directed by Engineer-in Charge.
Disconnecting existing tanks, setting aside (or lowering if required) for repairs cleaning etc and hoisting if required reconnecting and refixing in position after cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc complete (capacity of tanks exc 500 ltr and n exc 1000 ltrs)
M&L brick work with fly Ash bricks straight or curved on plan to any radius built in CM 1:6 all as specified and directed.
M&L half brick work with fly Ash bricks straight or curved on plan to any radius built in CM 1:4 all as specified and directed.
M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair complete all as specified.
M&L for Rendering 10+5 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified. (Water proofing compound to be measured and paid for separately).
M&L for Rendering 10mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in Charge.
M&L for Rendering 5mm thick on brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in Charge.
Suplly only liquid water proofing compound ISI marked complete
M&L for 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:3 and finished even and fair for receiving tiles on vetical surface mplete all as specified.
M&L for glazed coloured ceramic tiles in dado/vertical surface (350mm x250mm x 7 mm/450x300x7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface complete all as specified and directed.
M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 laying floor finishes complete all as specified.
M&L for Non skid coloured tiles (square/rectengular) 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified.
M&L for machine cut kota stone flooring 20-25mm thick over cement screed base laid and jointeed with pigment to match the shade of the slab including rubbing with bees wax polishing all as spd and as directed by Engineer-in-charge.
Cutting & grinding to existing kota stone flooring with bees wax polishing grinding upto mirror finish complete all as specified as directed by Engineer-in-Charge.
Applying a priming coat of bitumen primer @ 0.70 ltr/sqm complete all as specified and as directed by Engineer-in-Charge
M&L 50 mm PCC 1:2:4 using 20mm graded aggregate over stone roof slab as leveling course complete all as specified and as directed by Engineer-in-Charge.
Preparing surface and cleaning of concrete slab by wire brushing and applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.20 Kg per sq m including cleaning surfaces complete all as specified and as directed by Engineer-in-Charge
M&L 150 micron polyethylene sheet supplied and fixed complete all as specified and as directed by Engineer-in-Charge
M&L for 10 mm thick Rendering in cement mortar 1: 4 on concrete surfaces, finished Fair & even including mixing water proofing compound as per manufacturer's instns( WPC to be measured separately as supply only)
M&L for Lime concrete terracing as specified on roof complete all as specified as directed by Engineer-in-charge.
M&L for 40 mm thick Brick tiles bedded in 15 mm thick cement and sand mortar (1:6) and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed by Engineer-in-Charge.
M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed by Engineer-in Charge.
S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening complete all as specified and directed by Engineer-in Charge.
S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site. complete all as specified.
Supply and fixing of 100 mm But hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed by Engineer-in Charge.
S&F steel locking bolts with mils steel electrogalvanised plate and bright bolt ont less than 10 mm dia and 100 mm size, complete all as specified and directed by Engineer-in Charge.
S&F for 150mm size aluminium anodised barrel tower bolt of extruded section and fixed.all as specified and directed.
S&F for 150mm size aluminium anodised handle of febricated type and fixed.all as specified and directed.
M&L plain cement concrete type D2 1:4:8 using 40 mm graded stone aggregate as in foundations, filling and mass-concrete such as sunken floors complete all as specified and directed by Engineer-in Charge.
M & L 15 mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified.
Supply, laying and jointing GI tubes, medium grade 20mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches /under floor complete all as specified and directed by Engr-in-charge.
Supply, laying and jointing GI tubes, medium grade 40mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches /under floor complete all as specified and directed by Engr-in-charge.
Cutting existing steel tubing for alterations or additions done in position without taking down for 10mm to 40 dia pipe (Each cut measured) complete all as specified and directed by Engr-in-charge.
Refixing old GI tubing with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified.
Refixing old GI tubing with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified.
M&L for pre painted galvalume aluminium zinc cozting GI based corrugated steel Sheet high rib profile tile pattern color coated 0.5 mm thick of 550 Mpa Tensile strength sheets as in roof covering and fixed as per manufacturers instruction (design as app by Engg in charge complete all as spfd )
S&F 1000 ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, complete
S&F for Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 20mm bore (minimum weight 210 gms) complete.
S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed 0r in repair
S&F Gun metal gate valve 40 mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and directed .
S&F Gun metal gate valve 25 mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and directed .
Materal and labour for construction of brick masonary valve pit chamber of size 900x900x600 mm (Internal dimension) using sub class ,B, bricks complete, earth work, PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation, brick masonary sub class bricks 23 cm build n cement mortar and below ground level PCC with 1:2:4 type B2 using 20mm grade stone aggregate, copng 50 mm thick including frame of size 75x75x6mm made of angles iron and chamber cover made of MS sheet of 4 mm thickness double leaf including MS hinges locking arrangement with provision of locks and keys, painting of the steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer including necessary excavation, returning & filling & removing of surplus soil etc complete all as specified and as dircted by Engineer in Charge.
S&F Vitreous China Squatting pan `Orissa pattern` size 550x440mm including integral foot rest, incl P or S trap comp all as specified and fixed in repairs.
M & L for vitreous china wash down water closet pan (Pedestal pattern) with white seat cover and including bend and branch piece required to jointing with existing or new outlet connection comlete including fixing bolts, flushing cistern and flush pipe fixed in repairs complete
S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand including brackets & waste pipe etc complete all as specified.
S&F in repair 15 mm bore centre hole Brass CP mixer for mixing hot & cold water screwed down for iron pipe and complete all as spfd.
S&F in repair health faucet with 1 mtr long tube and hook and knab all as specified and directed by Engineer-in-Charge
S&F in repairs PVC flushing cistern 10 ltrs capacity incl flushing pipe and connections complete. as approved by Engineer in charge,low level, white with inlet, ball valve ,complete including connection to pipe all as specified.
S&F in repair Brass chromium plated wall mixer non telephonic for mixing hot and cold water screwed down for iron pipe 15 mm bore complete all as specified and as directed by Engineer-in-Charge.( Prayag/ Parryware/Cera)
S&Fin repair 15mm bore PVC connection with PTMT nuts length 450 mm complete all as specified and directed by Engineer-in Charge.
S&F in repair chromium plated Bib Tap, with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule, fancy type, CP, 15mm dia complete all as specified and directed by Engineer-in Charge.
S&F in repair fancy type chromium plated stop valve/Angle valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions chromium plated of size 15 mm. complete all as specified and directed by Engineer-in Charge.
S&F in repair 15 mm bore brass fancy concealed type stop valve chromium plated with long shank and cup complete screwed for iron pipe complete all as specified and directed by Engineer-in Charge.
S&F in repair Brass chromium plated shower rose 125 mm size with and incl shower arm complete all as specified and directed by Engineer-in Charge.
S & F in repair for tubular towel rail of Stainless steel, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed by Engineer-in Charge.
S&F stain less steel peg set with 06 no of hooks mounted on SS plate 4 mm thick with and including screws complete all as specified and directed by Engineer-in Charge.
S & F glass corner of size 300mmx300mm with 5.5 mm thick glass and steelness steel clip and steelness steel railing allround the shelf complete all as specified and directed by engineer in charge .
S&F in repair soap dish Make Jaquar/ cera or eqivalent complete all as specified.
S&F cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints laid in trenches all as specified.
S&F cast iron soil, waste and vent pipes (sand cast) 75mm bore in any length with or without ears with cement joints laid in trenches all as specified.
S&F cast iron soil, waste and vent pipes (sand cast) 75mm bore in any length with or without ears with cement joints fixed to wall all as specified.
S&F cast iron vent cowl for 75 m dia pipe. complete all as specified and directed by Engineer-in Charge.
S&F Cast iron bend (any radius) diminishing pieces or tapers/ Reducers/ Sockets/T 100mm bore fitted with oval access door. all as specified.(Larger bore measured)
S&F Cast iron bend (any radius) diminishing pieces or tapers/ Reducers/ Sockets 75mm bore fitted with oval access door all as specified.(Larger bore measured)
S&F 100 mm bore CI floor trap plain with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer-in Charge.
S&F 75 mm bore CI floor trap plain with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer-in Charge.
S&F stack clamps out of 100mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 75mm bore pipe complete all as specified and directed by Engineer-in Charge.
M&L for Salt-glazed stoneware gully traps size 125x100 mm, square or round mouthed, tvpe 'P' complete all as specified and directed by Engineer-in Charge.
M/L for ATT providing and injecting of Voide in masonary using chemical emulsion one liter per hole, at 300mm intervals including drilling holes, (note the treatment work shall be carried throught authorised agency only, and certificate for the same for warranty shall have to furnished before submitting payment) and drilling holes at 45 degree and plugging the same with cement motor 1:2 to match with existing surface complete all as specified and directed by Engineer-in Charge.
M&L for preparation of newly steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed by Engineer-in Charge.
M&L for Three coats of white washing on ceiling including preparation of New plastered surfaces complete all as specified and directed by Engineer-in Charge.
M&L for two coats of white washing on ceiling including preparation of old plastered surfaces complete all as specified. (Note:- Prepration of old surface shall include brooming down or steel wire brushing; scrappingdown soot moulds, moss and effloescent salts and trading oil nad greasy spout.)
M&L for three coats of white wash on walls old plastered surfaces complete all as specified and directed by Engineer-in Charge.
M&L for three coats of white wash on walls new plastered surfaces complete all as specified and directed by Engineer-in Charge.
M&L two coats of cement cement base paint on walls including preparation on new surfaces complete all as specified and directed by Engineer-in Charge.
M&L two coats of cement cement base paint on walls including preparation on old surfaces complete all as specified and directed by Engineer-in Charge.
De-sludging by removing of solid/semi solid sludge from existing drainage of any depth and capacity in foul conditions including taking and placing in position the cover slabs of any description including cement sand mortar 1:4 if required . Removal of will be remove to any place out side defence land or depositing where directed by Engr-in-Charge all as specified and directed.
Excavation in trenches n exc 10Sqm on plan n exc 1.5 m deep and n exc 1.5 m wide, getting out for laying of UG cable /Pole etc in any type of soil.
Returning filling in incl spreading levelling watering and well ramming in layers n exc 25cm thickness complete all as specified and directed by Engineer-in Charge.
Removing excavated soil to a distance n exc 50m and depositing at alevel n exc 1.5m above the starting point complete all as specified and directed by Engineer-in Charge.
Removing excavated soil/Demolished material to a distance n.exc 2.5 Km and depositing where directed at a level n.exc 1.5 above the starting point complete all as specified and as directed by Engr-in-charge.
M&L for conc 1:3:6 type C2 using 40mm graded aggregateas in bed to 150mm drain pies incl packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed by Engineer-in Charge.
S&F salt glazed stone ware drain pipe 150mm bore in trenches and jointed complete all as specified and directed by Engineer-in Charge.
M&L brick work in cement mortar (1:4) using old size sub class 'B' burnt bricks in walling, straight or curved on plan exc 6m mean radius all as specified.
M&L For PCC type B1(1:2:4) using 20 mm graded cushed stone agg as in coping ,benching and the like incl form work complete all as specified and directed by Engineer-in Charge.
M&L Precasted RCC 1:2:4 type B1 using 20mm graded aggregates for precast cement conc slabs as in drain/ manhole covers set in cement mortar1:4.(Note : Slab covers shall be floated with surface vibrator,and over turfed base ,arrandement for turfed base has to be from contractors side)
M&L for mild steel steel TMT bars 6mm to 8mm dia and over cut to length bent to shape reqd ,incl cranking ,bending spirally for hooping columns hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia
M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete ,using extra cement ,incl forms moulds ,mitered/stopped ends complete all as specified and directed by Engineer-in Charge.
M&L hardcore of broken stone or boulders gauge n exc. 63 mm, deposited, spread and levelled in layer n exc. 15 cm thick watered and rammed to a true surface complete all as specified and directed by Engineer-in Charge.
M&L for 75mm thick PCC (1:4:8), type C2 using 40mm graded stone agg as in sub base of floors etc finished even and rough complete all as specified and directed.
M & L for Screed bed or bedding layer of mortar(1:6) 15mm thick for laying floor finishes complete all as specified and directed.
M&L Chequered cement concrete tiles 20cmx20cmx25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment complete all as specified and directed.
M&L cement plastering 15mm thick in CM 1:4 on other than fair face of brick work surface finished even & smooth w/o using extra cement complete all as specified and directed by Engineer-in Charge.
M & L sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete all as specified and directed.
M&L for construction of Soak Well for 25 users, brick masonry, complete, all as specified and shown on drawings (BTD-830 Sheet No. 1/1).
M&L concrete bed to drain pipe in PCC 1:4:8 type D2 using 40mm graded stone aggregate incl packing under and hunching against sides of pipe after they are laid on slope and tested for 150mm dia bore sewer pipe line ( earth work excavation and sewer pipe line will be measured and paid separately)
Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft/loose soil
M & L 40mm thickDamp proof course to horizontal or vertical surfaces incl necessary formwork with PCC 1:2:4 type B-0 & mixing of water proofing compound as per manufacturer's instructions.
Earth filling under floors or in foundation incl watering, ramming and consolidation complete as directed.
M & L roughly squared stone lintels, beams, hammer dressed on face and soffits, hoisted, set and pointed in CM 1:4 complete n exc 3m in length complete all as specified and directed by Engineer-in Charge.
M & L stone for chajja,hammer dressed on face and soffits,hoisted,set and pointed in CM 1:4 complete all as specified and directed by Engineer-in Charge.
M & L for design mix RCC M-25 (20 mm graded aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified.
M & L for design mix RCC M-25 (20 mm graded aggregates) as in columns, pillars, piers, posts and struts complete all as specified.
M & L for design mix RCC M-25 (20 mm graded stone aggregate) in slab supported on walls, beams and coloums in roofs, floors, balconies, canopies desk slabs and in selves etc complete as specified.
M & L for design mix RCC M-25 (20 mm graded aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified.
Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; verticle or to batter for rough finished surfaces of concrete flat complete all as specified.
Formwork to sides of pillars, posts, struts, piers,columns, and stanchions for rough finished surfaces of concrete square,rectangular,polygonal complete all as specified.
Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, rough finished surfaces of concrete flat complete all as specified.
M & L for Formwork in soffits of suspended slabs such as roof slabs, landing ,and similar work not exc 200mm thick rough finished surfaces of concrete flat complete all as specified.
M & L for form work to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide complete all as specified and directed by Engineer-in Charge.
M & L for Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to cmplete as specified.
Ditto all as per item above 125 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified.
Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engineer-in Charge.
M & L Non skid coloured ceramic tiles of size 300x300x7mm thick as in flooring jointed in neat cement slurry and pointed with white cement mixed with pigments matching to tiles colour including 15mm thick screeding/ bedding layer in CM 1:6 complete all as specified and directed.
M & L Glazed ceramic colour tiles of size 300x200x7mm thick as in dado/ skirting jointed in neat cement slurry and pointed with white cement mixed with pigments matching to tiles colour including 10mm thick screeding/ bed plaster in CM 1:4 complete all as specified and directed.
M & L cement plastering 15mm thick in CM 1:6 on other than fair face of brick work surface finished even & smooth w/o using extra cement complete all as sepcified.
M & L for two coats of distemper oil emulsion on walls on newly plaster surfaces of walls incl preparation of surfaces.
M & L for two coats of Synthetic enemal paint/camouflage paint over a coat of priming coats including preparation of new plastered surfaces complete all as specified and as directed.
S & F Steel windows box type with side hung shutters including projecting type hinges with steel handles and steel pay stay, complete with glazing bars/without glazing bars, dovetailed or welded complete all as specified.
S & F box type steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and directed by Engineer-in Charge.
S & F M S Guard bars of 12mm square bars welded to steel frame of windows complete all as specified.
S & F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exec 0.5 sqm in each pane complete all as specified and directed by Engineer-in Charge.
S & F 4mm thick sheet glass pin headed type and glazing with oil putty in square n exec 0.5 sqm in each pane complete all as specified and directed by Engineer-in Charge.
M & L PCC 1:3:6 type C-1 using 20mm graded aggregate as in bed blocks etc for fixing windows, doors frames or other structural section as directed.
Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed
S&F 35mm thick Second class hardwood factory made plain, framed, panelled shutter (two panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete.
S&F 2nd class HW 35mm thick glazed and skeleton shutters open rebated and prepared to receive glass gauge etc (w/o sash bars) complete all as specified.
S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.
M & L for Preparing new or previously untreated surfaces of wood and wood based materials of any decription exceeding 10 cm in width or girth when un-connected with other painting or when painted in different tint and applying two coats of synthetic enamel paint over & including a coat of pink primer complete all as specified.
Supply only 100 mm MS butt hinges medium weight cold rolled mild steel complete all as specified.
S & F 200mm long alumimium barrel tower bolts extruded section complete all as specified.
S & F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed length of bolt 300 mm complete all as specified and directed by Engineer-in Charge.
S&F for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe,grating and union for discharge pipe and all fitting.
S&F CP towel rail 450 mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified.
S & F pillar tap cast copper alloy fancy type screwed for iron pipe on both ends of 15mm bore and fixed complete all as specified and directed by Engineer-in Charge.
S & F Stop cock cast copper alloy with crutch or butterfly handle screwed for iron pipe on both ends of 20mm bore and fixed complete all as specified and directed by Engineer-in Charge.
S & F Chromium plated 80 mm long shower rose with or without swivel joints, any size, incl fixing to steel pipe or union as in repairs complete all as specified and directed by Engineer-in Charge.
S & F 15 mm bore chromium plated angle cock cast copper allay, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipes complete all as specified and directed by Engineer-in Charge.
S & F PVC connections 15mm size with brass nuts of length 450mm complete all as specified and directed by Engineer-in Charge.
Supply, laying and jointing GI tubes, medium grade 25mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches/wall/under floor complete all as specified and directed by Engr-in-charge
S & F PVC (SWR) pipe of 100mm bore fixed to wall or laid in trenches complete all as specified and directed by Engineer-in Charge.
S & F PVC (SWR) pipe of 75mm bore laid in floors or trenches complete all as specified.
S & F PVC (SWR) bend any radius of 75mm bore jointed with solvent cement complete all as specified and directed by Engineer-in Charge.
S & F PVC (SWR) junction double (Single tee) of size 75mm bore jointing with solvent cement complete all as specified and directed by Engineer-in Charge.
S & F PVC (SWR) floor trap plain with grating including jointing with solvent cement of size 75mm outlet complete all as specified and directed by Engineer-in Charge.
M & L for 10 mm thick screeding in cement mortar 1:6 on concrete surfaces, finished fair & even including mixing water proofing compound as per manufacturer's instructions complete. (WPC shall be measured separately as supply only) all as specified.
M&L applying priming coat of cold bitumen primer at the rate of 0.40 Ltrs per Sqm as per para 11.44.5 of MES SSR Part-I incl cleaning and preparing the surface complete all as specified.
M & L APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. Not less than 150 gms/sqm) land on primed surfaces by forced application complete all as specified.
S&F 4mm dia Plain mild steel wire, galvanised class 3, in fencing including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured)
M & L for framed brackets of angles cut to shape,drilled and countersunk for screw.including bending and welding angles,as necessary conforming to Fe 410-0 or Fe310-0 all as specified.
M & L for PCC 1:3:6 type C-1 using 20 mm thick greded stone aggregate in chowkhats filling complete all as specified and directed by Engineer-in Charge.
M&L 60mm thick factory made coloured mixed with pigment precast concrete interlocking paver block of Grade M-35 confirming to IS 15658-2006 of any shape and size as directed with grey cement and pigment complete all as specified and as directed.
M&L for 25mm thick sand filling under floors, cushning under interlocking tiles or in foundations incl watering and consolidations complete all as specified and directed.
M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as in sub base,surface finished fair and even complete all as specified and as directed.
S&F Stainless steel drapery rod of 25 mm inner dia & 1.6mm dia wall thickness (in lengths as directed) with & including stainless steel sockets & decorative finial at both ends and pair of stainless complete all as specified.
Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as spcified and directed.
Taking down old U/S existing DB TPN 4 way and DB SPN 8 way including MCB/MCCB of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed.
M & L for point wiring for one light/fan/bell/buzzer point controlled by one way switch with 1.5 sqmm single core PVC insulated and sheathed multi stranded copper conductor FRLSH cable 1100 volts grade (ISI Marked) including 1.5 sqmm single core PVC insulated and sheathed multi stranded copper conductor FRLSH cable 1100 volts grade (ISI Marked) as continues earth wire in green colour to coomon earth dolly laid/drawn into and including non metalic PVC concealed conduit (medium duty, ISI marked not less than 20 mm dia) with all fittings such as tee, bends etc all as per IS terminated in & including new modular metal flush boxes of requisite module concealed in wall for mounting fittings like modular Switches, sockets, regulators etc with and including modular cover plates with frame of requisite modules all as specified and as directed: Notes:- (i) Cost of cutting/leaving forming chases for conduit, sinking for metal flush boxes and making good in CM 1:4 shall deemed to be included in quoted rate of this item. (ii) The quoted rates of this item shall deemed for include for modular metal flush boxes of requisite module and modular cover plate with frame of requisite module of colour as approved by GE (a) One Light/fan/ex-fan/Bell/point controlled by one switch.
(b)One pin 5 amps socket point on the same board with other switches complete
(c) One 3 pin 5 amps socket on independent board.
Ditto all as per item No 173 here -in- before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 sqmm single core PVC insulated and and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 2.5 Sqmm single core PVC insulated and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed .
Ditto all as per item No 173 here -in- before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4.0 sqmm single core PVC insulated and and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 4.0 Sqmm single core PVC insulated and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed .
S&F switch Modular type, 6 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.
S&F switch Modular type, 16 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.
M&L socket outlet 3 Pin 6 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.
M&L socket outlet 3 Pin 6/16 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.
S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed by engineer-in-charge.
S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as specified.
S&F LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Philips-BN021 LED 20S PSU CW GR S2/ Crompton Greaves LDDR20-CDL Dazzle Ray / bajaj-BCLAB 20W
Supply and fixing LED mirror light fitting , type with high out put diffuser 2 feet, 5watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.HAVELLS CAT PART NO-ENDURALINEARNEOBS10WLED865SPCWH/WIPRO CAT PART NO-LL20-111-XXX-65NE3/BCLSB 10 WH
S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-charge.
M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings Complete all as specified and as directed by Engineer-in-Charge
Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.
S&F GI bracket made out of 40 mm bore GI pipe light grade /medume grade, ISI marked, medium grade 1.2m long bent to shape suitable for fixing of street light fitting including with 2 Nos MS clamps made with 40x3mm flat iron, bolts, nuts, washers etc including two coats of synthetic enamel paint over one coat of zinc chrome primer and fixing on electric pole complete all as specified and as directed by Engr-in-charge.
Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and as directed by Engr-in-charge.
Supply and hanging/fixing ceiling fan 1200mm sweep AC supply (input voltage range 120 to 280v), BLDC type, 5 star rated BEE and ISI marked, super enameled copper winding of 'B' class insulation, single phase 20 watt (+ 10%), PF 0.90 (MIN), air delivery of 220 CUM per min (CMM), 350 RPM (+ 10%), TEMP RISE 40 DEGREE MAX, without remote, with electronic regulator, 3 blades, down rod including accessories, total harmonic less than 10%, 5 speed, hanging in position, including making connection wih and including flexible cord twin core twisted copper conductor of size 23/0.0076 from cealing rose to fan complete all as specified and as directed. Note :- (i) Sl No of cealing fan and GE office name shall also be writing on fan with red colour permanant marker. Cost for the same shall deemed to be included in quoted unit rate. Nothing shall be paid extra on this account.
supply and fixing fan step regulator modular type,120W -2 module electronic socket type five step controlled 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.
Supply & fix Air Circulator fans 230 volts single phase oscillating 450 mm sweep suitable for wall mounting complete all as specified and as directed
Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers Complete all as specified and as directed by Engineer-in-Charge
Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm Complete all as specified and as directed by Engineer-in-Charge
Taking down and refixing water heater storage type of 25 ltrs capactiy and 1500 watts, BEE Star rated-5, with glass line inner shell with Hot & Cold pipe, water connection pipe, electric connection and necessary repairing/replacement of inner tank, siphon assembly, glass wool, thermostate switch, heating element including washers, 3 core PVC insulated copper conductor cable etc including fixing arrangement complete all as specified and directed.
S & F water heater storage type 25 Ltr capacity, BEE 5 star and 8 bar pressure rated stainless steel (minimum wall thickness 2 mm) tank with feroglass coated inner container energy saving high density PUF insulation vertical ABS shock proof plastic body grouting of studs in wall in cement motar (1:3) nuts, washers, provision of two Nos PVC braided connection 450mm long heavy duty with brass nuts and two Nos brass chromium plated angular valve,thermostate,NRV ,TOP PLUG 20AMP with valve flange suitable for 15mm bore pipe for water supply connection complete.
Supply and fix desert cooler electric driven (singal phase) having nominal air flow capacity of 4000 CUM per hour, steel body Complete all as specified and as directed by Engineer-in-Charge
S&F sheet metal enclosure MCB DB, double door, vertical TPN 4 way with 200 Amps rated busbar all as specified and as directed. Make:- Hegar/Legrand/Seimens
Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of TPN (4 Poles) and 40 To 100 AMP current carrying capacity in the DB complete with connection testing and commissioning all as specified and as dircted by Engr-in-charge..
S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.
S & F MCB SP, 5-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.
S & F MCB SPN, 5-32 Amps, 240 volts, breaking capacity 16KA complete all as specified and as dircted by Engr-in-charge.
Excavation in trenches n. exc 1.5 m in depth and not exc 1.5 m width for laying of cable lines etc and getting out in hard/ dense soil complete all as specified.
M&L for Earthing complete with galvanized steel earth plate electrode 60cm x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level connecting to the galvanised earth lead wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanized iron and steel earth wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -5 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.
Supply & Laying & commissining of LT UG cable XLPE sheathed PVC insulated, screened PVC bedded, galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volts grade, laid in tranches, in GI pipe, including brass cable glands, clamps etc of size 3.5 core x 50 Sqmm complete all as specifed and as directed. Make : Polycab/KEI/Havells Note: Earthwork, sand cushioning, bricks, GI pipe, etc will be measured and pad under appropriate items.
Supplying and laying un-reinforced precast concrete cable cover, class Class LV, Type I, flat, size 250mm x 150mm x 40mm Complete all as specified and as directed by Engineer-in-Charge
M&L for Sand Cushioning (dry) in trenches/ducts for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 23 cm spread thickness (8 cm in depth before laying the cable and 15 cm in depth after laying the cable) and consolidated (punned) upto 180 mm thickness, complete all as specified and as directed. Note : For the purpose of payment, punned thickness of sand cushioning only shall be measured and paid for.
Supply and fixing GI Pipe light grade og Size 80 mm bore with all fittings for passing of cables fixed to pole/wall/laid under floor or roads including all fixing accessories complete for protection of cable all as specified and directed. Make: Jindal/ Bansl/Tata
Supply and laying bricks (old size) for cable protection by using common burnt clay building bricks, sub-class ‘B’ designation 75 laid dry flat across length of the cable with width of the trenches equal to length of bricks and all as directed.
Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 2 core complete all as specified and directed.
S&F GI tubing light grade 40mm dia for protection of cable on pole/ wall etc complete all as specified and as directed by Engr in charge.
SUBHAM ENTERPRISES
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .