GE U(N) 64 2021 2022 PROVISION OF GROOMING SHED FOR ARMY DOGS AND SPECIAL REPAIR TO BLDG NO NP 16 AND NP 19 UNDER OF GE NORTH UDHAMPUR

Amount

M&L for demolition of brick work built in CM including all quions arches pillars etc complete all as specified and as directed by Engr-in-Charge.

M&L for demolition of cement concrete of any description in any position complete all as specified and as directed by Engr-in-Charge.

M&L for dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed by Engr-in-Charge.

M&L for dismantling ceiling boards,fibre pulp insulation etc or insulation boards/slabs/blankets,any thickness, including cover and mild steel Tee grid, complete all as specified and as directed by Engr-in-Charge.

M&L for demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground) complete all as specified and as directed by Engr-in-Charge.

M&L for dismantling of floor hearth or wall tiling incl CM, bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-in-Charge.

M&L for dismantling timber Scantling 40 Sq Cm and over in Section, in any Position, as in Unframed Work, complete all as specified and as directed by Engr-in-Charge.

M&L for taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed by Engr-in-Charge.

M&L for taking down chowkats or frames with shutter in brackets without taking off shutters from frames exc 1.5 sqm sqm but n.exc 4 sqm each including cutting holes for taking out hold fasts or dismantling brick work ( holes cut and any other damage to jambs, wall for taking out hold fast shall be finished idential to existing finish without any extra cost to the Govt) complete all as specified and as directed by Engr-in-Charge.

M&L for taking down shutters of any description not exc 1 sqm from chowkhat and removing to or from store as required complete all as specified and as directed by Engr-in-Charge.

M&L for excavation in trenches n exc 1.50 m in width and n exc 1.50 m in depth for foundation/ laying of cables etc or for shafts wells cesspits , manholes, pier holesetc n exc in 10 sqm on planand not exc1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed by Engr-in-Charge.

M&L for excavation in post holes in soft/loose soil, each n. exc. 0.50cum, getting out , returning, filling in and ramming moorum or broken rubble mixed with moorum in layers n. exc. 25 cm thick, watering, and removing excavated soil to a distance n. exc. 50m and making good surfaces complete all as specified and as directed by Engr-in-Charge.

M&L for returning filling incluiding spreading levelling watering and well ramming in layer n exc. 25 cm in soft/loose soil complete all as specified and as directed by Engr-in-Charge.

M&L for removing excavated soil to a distance n.exc 50 mtr and depositing where as directed at a level of 1.5 m above the starting point complete all as specified and as directed by Engr-in-Charge.

M&L for surface excavation n.exc 30cm deep & averaging 15cm deep and getting out in any type soil complete all as specified and as directed by Engr-in-Charge.

M & L for moorum/ red bajri filling in floors or pavings, foundations etc laid in layers n. exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed by Engr-in-Charge.

M&L for 100mm thick for hard core of gauge exc 63 mm but n.exc 100 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rolled/ rammed to a true surface of Broken stone or boulders complete all as specified and as directed by Engr-in-Charge.

M&L for hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by Engr-in-Charge.

M & L for plain cement concrete 1:3:6 , type C-2, using 40mm graded stone aggregate as in foundation filling and mass concrete for erecting fencing posts complete all as specified and as directed by Engr-in-Charge.

M & L for plain cement concrete 1:4:8 , type D-2, using 40mm graded stone aggregate as in foundation filling and mass concrete for erecting fencing posts complete all as specified and as directed by Engr-in-Charge.

M & L for plain cement concrete 1:3:6 , type C-2 using 40 mm graded stone aggregate as in walls,or retaining walls any thickness , size or shape including pillasters, buttresses, cols,pillars,boundary pillars and posts.( incluiding caps and bases) incluiding necessary form work complete all as specified and as directed by Engr-in-Charge.

M&L for providing precast cement concrete kerb stone type B1 1:2:4 (20mm gradded aggregate) of any section as indicated with plain fair faces including champers, weathering,throating and setting in cement mortar 1:4 complete with joints to match complete all as specified and as directed by Engr-in-Charge.

S&F Pre-painted Coloured profiled Galvalume/Zincalume sheet with min 0.5mmTCT with BTM of 0.45mm thick conforming to IS 513 (AZ-150 GSM,Al zinc alloy metallic coating 550 Mpa yeild stess as per AS-1397) as in roof covering/cladding to wall fixed with self tapping screws,colour/exterior coat of silcon modified polyster/BHPX RW paint system 20 micron top coat applied over 5 micron primer all fixed with galvanised self drilling self tapping fastener 12-14x55 with EPDM seats complete all as specified and directed.

S&F Pre-painted Coloured plain steel profiled Galvalume/Zincalume sheet with min 0.5mmTCT with BTM of 0.45mm thick conforming to IS 513 (AZ-150 GSM,Al zinc alloy metallic coating 550 Mpa yeild stess as per AS-1397) as in roof covering/cladding to wall fixed with self tapping screws,colour/exterior coat of silcon modified polyster/BHPX RW paint system 20 micron top coat applied over 5 micron primer all fixed with galvanised self drilling self tapping fastener 12-14x55 with EPDM seats complete all as specified and directed.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) with old size bricks complete all as specified and as directed by Engr-in-Charge.

M&L for half brick work with sub class 'B' bricks , straight or curved on plan to any radius in half bricks thick walls built in CM 1:4, complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 15mm(10+5 mm) thick in cement mortor 1:4 on fair faces of brick work or concrete surfaces complete all as specified and as directed.

M&L for 15mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 10 mm thick in cement mortor 1:6 other than fair faces of brick work or concrete surfaces complete all as specified and as directed by Engr-in-Charge.

Supply only integral water proofing compound complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of new plaster surfaces of wall and applying two coat of cement base paint over a coat of alkali resistant primer paint including 2mm thick wall care putty finishes complete all as specified and as directed by Engr-in-Charge.

M&L two coats of oil bound distemper over a coat of primer over 2 to 3 mm thick approved wall care putty over and including preparation of new plastered surfaces of wall complete all as specified and as directed by Engr-in-Charge.

M&L for reparing of newly plastered or unplastered surfaces of wall and applying two coats of white wash complete all as specified and as directed by Engr-in-Charge.

S&F stainless steel powder coated curtain rods with bracket fixed to wall with suitable screws and onion type end brackets all as per approved design/colour/pattern fixed as directed in Engr-in-Charge.

S&F in 3mm Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane all as specified.

M&L for stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel staples complete, all as specified and directed by Engr in Charge.

S&F false ceiling non asbestos fibre Cement board ceiling 4mm, thick in 600x600mm panel designed ceiling conforming to IS-14862 type B in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 gmild steel, both side inclusive) consisting of main 'T' runner with suitably spaced joints to get required length, and 15x32 mm made of 0.30 mm sheet, and cross'T' at 600mm c/c to form a grid including, required cutting/making, opening for services like diffusers,grills,light fittings, fixures,smoke detectors etc . Main 'T' runners to be suspended from ceiling using GI soffit cleats fixed to existing rafter, purlin, etc with gavanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15 mm of all T- sections shall be centre black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, and refixed all exesting electric wiring and fixture all complete at all heights as per direction of Engineer-in -Charge.

M&L for coloured vitrifired ceramic tiles 10mm thick (square) polished , light shade, area of each tiles exc 0.18 sqm but n.exc 0.38Sq.m (min. size 600mm x 600mm) in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement incl 10mm thick screed bed in CM (1:4) complete all as specified and as directed.

M&L for coloured vitrifired ceramic tiles 10mm thick (square) polished , light shade, area of each tiles exc 0.18 sqm but n.exc 0.38Sq.m as in skirting, etc, set and jointed in neat cement slurry and pointed in white or coloured cement incl 10mm thick rendering in CM (1:3) complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (sqare/ rectanglear) area of each tile exc 0.11sqm but n exc 0.18 sqm in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick screed bed in Cement mortar (1:4) complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surfaces of wall of size 450mm x 300mm x 7 mm thick as approved pattern approved by GE, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick rendering in Cement mortar 1:3 as in skirting, dado, etc, complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20mm thick over 20 mm th cement screed in CM 1:4 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Granite stone slab of any colour nosing rounding edges directed colour, 18 mm thick machine cut,as in cills/skirting/ dado bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, over 10mm thick rendering in CM 1 :3 complete all as specified and as directed.

M&L for providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection even and smooth with using extra cement complete all as specified.

M&L for plain cement concrete 1:4:8 type D-2 as in floors 75mm thick complete all as directed & specified complete all as specified and as directed by Engr-in-Charge.

M&L for 100 mm thick Cement concrete type D-2 , 1:4:8 using 40mm graded aggregate as in subbase complete all as specified and as directed.

M&L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade Grade) complete all as specified and as directed by Engr-in-Charge.

M&L for Machine pressed concrete interloking paver block glossy finish,any shape and size confirming to IS 15658-2006 of 60mm thickness,M-35 grade with grey cement and pigment over 50mm thick sand cushion complete all as specified and as directed by Engr-in-Charge..

S & F in repairs viterous china WHB (flat back or angle back) any size, including cutting for and pinning in ends of brackets complete with waste pipe and all fittings complete all as specified and as directed by Engr-in-Charge.

S & F chromium plated towel rail 600 mm long complete all as specified and as directed by Engr-in-Charge.

S & F PVC connection colour 600 mm long suitable for cold water connection complete all as specified and as directed by Engr-in-Charge.

S&F PVC bathroom cabinets quality as approved by Engr-in Charge, of size 600mmx400mm with mirror on front door and with one towel rail for hanging towel of mild steel chromium plated fixed with screw and wooden gutties etc, complete all as specified and as directed by Engr-in-Charge.

S & F PVC (SWR) Floor trap of 75 mm outlet plain with grating including jointing with solvent cement. complete all as specified and as directed by Engr-in-Charge.

S & F viterious china squatting pan ORISSA Pattern size 580x440mm with integral foot rests, (excl flushing cistern and flush pipe) but with and incl connection to trap, and to flushing pipe anti-syphonage pipe, etc. complete incl provn of lime concrete and making good to floor, in repair complete all as specified and as directed by Engr-in-Charge.

S & F bib taps, brass, chromium plated, fancy type, long nose, with capstan head handle screwed down high pressure, including chromium plated brass wall flanges; screwed for 15mm bore pipe connection complete all as specified and directed.

S & F chromium plated brass soap dish complete all as specified and as directed by Engr-in-Charge.

S&F Glass self ( With chromium plated brakets) complete all as specified and as directed by Engr-in-Charge.

M&L for 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layer white in colour (inside outside) hoisted and fixed in position incl inlet, outlet and overflow connection nipple of suitable size all as specified

S & F ball brass valve 20mm dia high pressure with polythene float and fly nut complete all as specified and directed.

S&F 15 mm bore steel water Tubing 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engr-in-Charge.

S&F 20 mm bore steel water Tubing 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engr-in-Charge.

S&F 25 mm bore steel water Tubing 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engr-in-Charge.

S&F 25 mm Gun metal , global or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by Engr-in-Charge.

S&F PVC low level flushing cistern 10 ltrs capacity , valve less, syphonic action type, white, with inlet, ball valve, float and handle including brackets, PVC 32mm dia flushing pipe etc., fixed in repairs,complete all as specified and directed.

S&F Toilet paper holder, brass, chromium plated, heavy duty, fixed with brass screw complete all as specified and as directed by Engr-in-Charge.

S&F pillar tap 15mm dia with capstan head screwed down high pressure complete all as specified and as directed by Engr-in-Charge.

S&F Vitreous china bowl urinal flat back, size of 465 X 355 X 265 mm white with grating and union for discharge pipe including, waste pipe and PVC connection, bedding urinal against wall in cement mortar 1:2 securing urinal to, plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and directed by Engineer-in-Charge.

S & F in repair Angle cock/stop cock cast copper alloy 15mm bore screwed down high pressure chromium plated concealed type complete all as specified and as directed by Engr-in-Charge.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified and as directed by Engr-in-Charge.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified and as directed by Engr-in-Charge.

S&F 75mm dia PVC (SWR) bends with oval with rubber ring joints fixed as required complete all as specified and as directed by Engr-in-Charge.

S&F 110mm dia PVC (SWR) bends with oval with rubber ring joints fixed as required complete all as specified and as directed by Engr-in-Charge.

S&F 110mm dia PVC (SWR) junction double, (double T), equal or un equal with oval accesse door including jointing with solvant cement as required complete all as specified and as directed by Engr-in-Charge.

S&F 75mm dia PVC (SWR) junction double, (single T), equal or un equal with oval accesse door including jointing with solvant cement as required complete all as specified.

S&F 110mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 75mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 110mm dia PVC (SWR) reducer, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 75mm dia PVC (SWR) vent cowl, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 110mm dia PVC (SWR) "P" trap single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S & F for factory made solid panel PVC door shutters 30mm thick (style) consisting of frame made out of mild steel tube for top and bottom rails. mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struk complete all as specified and as directed by Engr-in-Charge.

S&F solid PVC door frame of size 50mm x 47mm made out 5mm thick PVC sheet prelaminated on single side and plain on other side reinforced with mild steel square tube including painting of edges to match with prelaminated sheet, fixed in opening as per specification complete all as specified and as directed by Engr-in-Charge.

M&L for powder coated Anodised Aluminium door air tight of anodised frame made of size 100 mm x 45mm of section thickness -1.50 mm thick with one or more rebates including jointing cleats etc for fixing aluminium anodised door shutter fully panelled (two no of panels on each shutter) with 5.5 mm thick tinted glass as in panels shutter rail made of 80mm x45 mm of sheet thickness 1.50 mm (Top and bottom rails and stiles) single /double leaf side hung type including necessary jointing cleats /anodised aluminium fillets/ glazing clips with rubber gasket ,with aluminium fittings such as aluminium anodised tower bolt 200mm long 03 No for each door, aluminium anodised bow handles 150 mm 'D' type 02 nos for each shutter , mortice locks 6 lever make - harrison one on each door, door shutter mounted on bottom double action floor spring hydrailically regulated made up of 1.25mm thick aluminium alloy sheet foundation box , main body with stainless steel cover , governing mild steel heavy duty and door shutter top mounted on aluminium alloy pivot. -01 No on each shutter , bottom and floor stoppers, Complete all as specified. Note : All fitting shall be of ISI marked except cleats ) sizes of each door shall be as per site requirement all as directed and specified .

M&L for powder coated Aluminium window air tight of anodised frame made of size 100mm x 45mm of section thickness-1.50mm thick and shutter stiles made of section 80mm x 45mm x 1.5mm thick with or without rebates, with 5.5mm thick tinted glass fixed with aluminium beads, including necessary jointing cleats/anodised aluminium fillets/alluminium glazing clips with rubber gasket, with aluminium fittings such as aluminium butt hinges 100mm long 03 Nos, aluminium anodised tower bolt 100mm long 02 No, aluminium anodised bow handles 100mm 01 No, aluminium hook and eye 150mm 01 No in each shutterm including aluminium grill of 5 to 6 dia, size of mesh not exc 7.5cm in either direction, as approved by GE, complete all as specified. Note:- All fitting shall be of ISI marked except cleats ) sizes of each shutter shall be as per site requirement all as directed and specified .

M&L for powder coated aluminium louver ventilators in WC & bath with 5mm thick frosted glass etc complete all as specified and as directed by Engr-in-Charge.

M&L for mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS-1239 (Part I-1990).all as per specified and directed by engr-in-charge.

M&L for Rolled mild steel plates (plain or chequered), square cut or notched (ordinary or counter sunk) forming holes etc of Gde Fe-410-S. complete all as specified and as directed by Engr-in-Charge.

S&F framed work as in doors or gates of approved pattern & design of angle or other section conforming Fe 290 (Gde-E- 165) with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering of doors, etc. to be prepared for hanging or sliding with and including either hooking and hinges or steel hanging door fittings (including of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, complete all as specefied and and directed.

Mild steel work as in angle iron (65x65x6mm) fencing posts, struts including cutting, tops to shape as directed, bent to shape, drilling holes, notching for wire etc including all necessary bolting or riveting etc and embedding in concrete complete all as specified and as directed by Engr-in-Charge. Note:- Earth work and concrete shall be measured and paid for separately under respective item

Mild steel flat iron (40x6mm) supports for posts/struts for securing fencing (chain link) using mild steel rods including drilling holes, notching for wire etc complete all as specified and as directed by Engr-in-Charge.

Supply and fixing mild screw bolts(machine made) with hexagonal heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal head, dia of bolt 5 mm to 10 mm & length n. exc 5 cm complete all as specified and as directed by Engr-in-Charge.

Fixing only galvanised, 2 strand steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacings and straining and fixing to fencing posts, any type of standard rails, straining bolts, including securing or tying at crossings with and provisions of galvanised mild steel wire staples or steel nib,pins etc complete all as specified and as directed by Engr-in-Charge. ( each line of wire to be measured )

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and as directed by Engr-in-Charge . Note:- Supply of chain link and mild steel galvanised line wire shall be measured and paid separately under respective item

Supply only chain link mild steel galvanised fencing of size 100x100mm, 3mm dia complete all as specified and as directed by Engr-in-Charge.

Supply only 4mm dia plain mild steel wire, galvanised class 3 , in fencing including straining and fixing to steel posts and/or to straining bolts complete all as specified and as directed by Engr-in-Charge.. (each line of wire to be measured)

M&L for preparation of new steel surface of any description not exc 10 cm in width or grith when unconnected with other painting & applying two coats of synthetic enamel paint over a coat of zine chrome primer complete all as specified and as directed by Engr-in-Charge.. Note:- Galvanised steel surfaces (chain link) is excluded from above item.

M&L for preparation of new steel surface of any description and girth, not otherwise described for and treated end of posts, back of chowkhats etc with tar or coal tar black paint, area tarred exc. 0.10 sqm but n. exc. 0.50 sqm each complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of new steel surface of any description exc. 10 cm in width or grith & applying two coats of synthetic enamel paint over a coat of zine chrome primer complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engr-in-Charge.

Taking down carefully point wiring copper/aluminium (light, fan, socket, and power) complete (fittings such as switches ceiling roses, pendent regtulators sockets etc to be measured and paid for separately removing materials to store for keeping of safe custody and making good the disturbed surfaces complete all as specified and as directed by Engr-in-Charge.

M&L for point wiring with PVC insulated unsheathed, FRLS 1100 volts grade stranded copper conductor cable single core 1.5 Sqmm for one light / fan point/bell point controlled by one way switch, and wire to be drawn in and including concealed conduit of dia not less tham 25mm complete with all accessories including mild steel sheet metal 1.2 mm thick switch board of suitable size be fixed flush wall , with 3 mm thick ebonite sheet cover and necessary screws, cap washers etc. or to be fixed on wall respectively as directed by EIC and providing earth continuity wire using PVC insulated, un sheathed single core stranded copper conductor FRLS cable of size 1.5 Sqmm complete all as specified and as directed by Engr-in-Charge.

All as per item No 100 above but for one 3/5 pin socket 5 Amp on same board with cable1.5sqmm size.

All as per item No 100 above but for one 3/5 pin socket 5 Amp on independent board with cable1.5sqmm size.

All as per item No 100 above but for 3 pins socket outlet 15 Amps independent with 2.5 sqmm incl continous earthing with multistandred copper conductor PVC insulated unsheathed size 2.5 Sqmm complete all as specified and as directed by Engr-in-Charge.

S&F Switch Piano flush type single pole 5 Amps One way, complete all as specified and as directed by Engr-in-Charge.

S&F socket flush type single pole 5 Amps One way, complete all as specified and as directed by Engr-in-Charge.

S & F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal complete all as specified and as directed by Engr-in-Charge.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. complete all as specified and as directed by Engr-in-Charge.

S&F Ceiling rose, 3 terminal, PVC / polycarbonet, isolated body complete all as specified and as directed by Engr-in-Charge.

S&F Slim linear LED lighting fixture 20 watt LED batten, with full base of extruded aluminium section acting as a heat sink with closed back, isolated driver, complete making all connection using 1.5 sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings complete including taking down old US tube light fitting 1x36W complete all as specified and as directed by Engr-in-Charge.

S&F LED light fitting PLUTO NEO PANEL 2'x2' PLR 36 watt LED 857S environmental friendly , new generation , aesthetically designed ,ultra modern recess mounting luminaire with high brightness SMD LEDs as light source suitable for armild steeltrong /grid /ceiling complete all as specified and as directed by Engr-in-Charge.

S&F in replacement E-Lite LED Curve lighting fixture for mirror 10/12 watt LED batten,2' long with full base of extruded Aluminium body environmental friendly, energy efficient ready to use pack with isolated driver, complete making all connection using 1.5 sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings complete including taking down old unserviceable tube light fitting 1x 18 watt from the site complete all as specified and as directed by Engr-in-Charge.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed by Engr-in-Charge.

Taking down fan, ceiling cable end, dismantling blades and kept in safe custody for refixing on same location complete all as specified and as directed by Engr-in-Charge.

M&L for repair of ceiling fan/exhaust fan 1200/300 mm sweep of any make obtained from above item, oiling, greasing cleaning slot, over hauling & replacement of defective nut bolts washer etc including painting. If as per site requirement fan will be found burnt rewinding will be provide by the contractor as per unit quoted rate all as specified and directed.

Hanging /fixing only ceiling fan/Exhuast fan and connecting up including provision of cable from ceiling rose or connector to fan obtained from site complete all as specified and as directed by Engr-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed by Engr-in-Charge.

M&L for submain wiring with 2X6.0 SQMM+1X6.0SQMM Earth Wire single core PVC insulated FRSL sheathed cooper cable connecting to common earth dolly in and including heavy duty PVC Concealed Conduit as per site requirement including taking down old us submain wiringand direction by EIC, all accessories complete all as specified and directed.

S & F single pole and neutral sheet steel powder coated Distribution board for MCBs fitted with bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 12 ways complete all as specified and as directed by Engr-in-Charge.

S&F 'C' series SPN MCB 40 to 63 Amps 240V ,50Hz,10kA lighting and other domestic loads incl all termnials, fitting etc. complete all as specified and as directed by Engr-in-Charge.

S&F 'C' series SP MCB 06 to 32 Amps 240V ,50Hz,10kA suitable for lighting and other domestic loads incl all termnials, fitting etc. complete all as specified and as directed by Engr-in-Charge.

S & F sheet metal TPN DBs - DPX3 160 MCCB DBs 04 way (DPX3 160+ 12) with metal door 415 volts grade IP 43 Protection Grade fixed flush to wall complete including connections should be provide with necessary reducer lugs complete all as specified and as directed by Engr-in-Charge.

S & F DPX3 thermal magnetic MCCB 3 pole 100 Amps 415 Volts 16 ka INCLUDING MAKING NECESSARY ARRANGEMENT complete all as specified and as directed by Engr-in-Charge.for MCCB DB

M & L for replacement of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps 240 volt capacity complete all as directed.

M&L Earthing complete with galvanised steel earth plate electrode 60x60cmx6mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No-5 of MES Part-1 fixed in replacement including testing on completion including the material and labour of the following :- (a) Excavation and earth work for drilling hole for electrode in any type of soil. (b) plain cement concrete Pit in cement concrete 1:2:4 type B-1. (c) Precast RCC cover with suitable handle 40mm thick in plain cement concrete 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. (d) Funnel with watering pipe of GI protection pipe 5 mtr long for protection of earthing lead from mechanical injury or tempering. (f) Requisite quantity of common salt and charcoal. (g) Testing of Earthing.

Supply and fixing Exhaust fans steel body,AC single phase 230 volts of size 300 mm sweep with blades and frame and louver complete all as specified and directed

Supply and lay XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 4 core in trenches/floor/pole/GI pipe complete including cutting/chasing to any surface and making good to the disturbed surface to match the existing complete all as specified and as directed by Engr-in-Charge.

Supply and lay XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core in trenches/floor/pole/GI pipe complete including cutting/chasing to any surface and making good to the disturbed surface to match the existing complete all as specified and as directed by Engr-in-Charge.

M&L for dry sand cushioning to under ground cables provided with a layer of sand 8 cm deep before laying the cable, 15 cm depth after laying cable & stretching the cable complete all as specified and as directed by Engr-in-Charge.

Supply and laying brick class ‘B’ covering as mechanical protection to cable with well burnt complete all as specified and as directed by Engr-in-Charge.

M&L GI tubing light grade with all fitting and fixed in wall and floor or fixed to pole of size 40mm dia complete all as specified and as directed by Engr-in-Charge.

SHIVAE CONSTRUCTION

M/s LAL DAYAL CONSTRUCTION CO

KUMAR CONSTRUCTION CO

paras ram pachiala

RAMAN CONSTRUCTION CO

M/S Inderjit Sharma and Co.