REPAIR TO FLOORING PLASTERING JOINERY CEILING STONE MASONARY ROOFING IN CERTAIN UNITS AT ZONE 1 AT MIL STN JAISALMER

Amount

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing, removing serviceable tiles).

M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floors & finishing the surface even & smooth without using extra cement.

M&L for non skid ceramic coloured tiles of size 300x 300 by 7mm thick as in floors set & jointed in neat cement slurry and pointed in coloured cement to match the tiles and including scread bed or bedding layer 15mm thick in CM 1:6 all as specified.

M&L for ceramic tiles exterior grade 300 x 300 x 10mm (Endura from Johnson or equivalent) including screed bed in CM 1:6, 15 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match all as specified and roughening of exc concrete surfaces all as directed

M&L for vetrified ceramic coloured tiles 9 to 10 mm thick area of each tile exc 0.18sqm but not exc 0.38sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement over 15mm thick screed bed in CM 1:6 all as directed (size 600mm to 600mm)

...ditto…as per item no 05 above. but as in skirting, steps etc in vertical surfaces with 10mm thick backing coat in CM 1:4

M & L non skid ceramic coloured tiles 7-8mm thick(square/rectangular) area of each tile exceeding .11Sqm but n.exc .18Sqm in floor set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6.

M & L glazed ceramic coloured tiles (450x300mm)x 7mm thick joint free in dado/skirting set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 etc.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L for 75mm thk cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in subbase of flooring/hard standing as specified

M & L for 60mm thk, M 35 grade machine pressed precast concrete interlocking paver block rubber mould using grey cement and no pigment of any shape and size conforming to IS 15658 - 2006 laid over incl 25mm thk sand cushoining complete.

S & F rubber moulded chequered cement concrete tiles 20cm X 20 cm X 25mm thk with grey cemnt and pigments,set jointed in neat cement slurry as in floors/path etc over and including 15mm thk screed bed in CM 1:4 complete.

M&L for PCC 1:2:4, 100mm thick using 20mm graded aggregate as in flooring.

M& L for PCC 50mm thk type C1 1:3:6 (20mm graded stone aggregate laid in alternative as in plinth protection including finished the surface even and fair without using extra cement and filling the joints with mastic filling ie one part of bitumen 85/25 & 3 parts of sand by weight

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. loaded bedded and pointed in any mortar

M & L for Granite (of any type) tiles18 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types

M&L for machine cut kota stone flooring 550 x 550x 20 to 25mm thk laid over cement screed bed jointed & pointed with grey cement slurry mixed with pigment to match the shade including rubbing &mirror polishing including over a screed bed or bedding layer of 15mm thk in CM 1:6 for laying floor finishes all as specified and directed.

ditto above but on vertical surfaces such as skirting /dado etc including over a screed bed or bedding layer of 10mm thk in CM 1:3 for laying tiles all as speciifed.

Taking down cement plaster on brick/stone/concrete surface including wall tiling or terrazo finish and hacking out joints hacking for key scrubbing down with water etc complete

M & L rendering 10mm thick on surface of stone masonry or surface other than fair face of brickwork in CM 1:6 all and it is to be finished even and smooth without using extra cement all as specified

M&L for rendering 15 mm thick on stone masonry surfaces or surfaces other than fair faces of brick work or on one side of lathing in cement mortar 1:4 & finished the surface even & fair without using extra cement all as specified.

M&L for rendering 5 mm thick on fair faces faces of brick work or concrete surfaces of ceilings in cement plaster 1:3 & finished the surface even & fair without using extra cement all as specified.

M & L preparation of new plastered surfaces and applying three coat of white wash on walls complete

M&L for preparation of new surface and applying two coat of distemper oil emulsion after applying one coat of alkali resistant primer complete all as specified and as directed by Eng-in-Charge.

M & L preparation of new plastered surfaces and applying three coat of white wash on ceiling

M & L preparation of new plastered surfaces and applying two coats of cement base paint over a coat of white wash on walls

Taking down shutters of any description not exc 1 Sqm each all as specified and as directed

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each all as specified and as directed

Taking down chowkat (without taking of shutter from the frame) not exc 1.5 sqm each including making good the disturbed surface in PCC 1:2:4 type B0 or CM 1:3 all as specified and as directed

Ditto- all as per item No 29 above but exc 1.5 sqm and n exc 4 sqm each

S & F factory made second class hard wood plain framed panelled shutters 35mm thick with panels of timber flat on both sides (feather edged) or of veneered particle board medium density wood particle tone veneers, fixed to chowkhat all as specified and as directed.

S & F glazed and skeleton shutters, open rabated and prepared to receive glass gauge etc second class hard wood 35mm thick for door shutter all as specified and directed

Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M S square tubes, S&F in opening as per specification & drawing given in SSR-2004.

S/F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawingetc all as specified and directed.

S & F mild steel tower bolts 150 mm long stove enameled black with bright bolt complete all as specified and directed.

S & F aluminium anodized tower bolt 150mm size complete all as specified and directed.

S & F Butt hinges Aluminum 100 mm type C21 complete all as specified and as directed

S & F aluminium handle 125 mm cast type anodized

S & F mild steel sliding bolt 300 mm long plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fix complete all as specified and as directed

S & F Butt hinges MS 100 mm cold rolled complete all as specified and as directed

S & F MS Pressed handle 150mm size oval type stove enameled black

S & F steel windows with side hung shutters including projecting type hinge with steel handle and steel peg stay ,complete with glazing bars ,devetailed or welded

S & F sheet glass 3mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane and all as specified.

Galvanized mild steel wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanized wire staples fixed as in reparis

S & F figured glass pin head type 3mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane and all as specified.

M&L for Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified.

M&L for Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

Prelaminated particle board, 18/19mm interior grade, prelaminated both sides withdec orative choice laminations & other side balancing white lamination, fixed with screws to timber frame work

Sheet glass, 5.5mm ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty approved by Engr-in-Charge

Dismantling (AC corrugated , semi corrugated etc) AC sheets in roof coverings complete all as specified & directed by Engineer in charge.

S&F Pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet/ semi corrugated 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws as specified.

Dismantling wrought iron or mild steel work of any description not othervise provided for that purpose.

S &F Rolled nild steel framed work as in door or gates of angle or other section confirming to Fe - 410-S with gusset plates, rail braces etc complete drilled for fixing of steel sheeting or other covering and hanging and fixing complete.

S & F Joist, channel,angel or tee sections, fixed independently , without connecting plates etc

M & L preparation of new steel surfaces exc 10cm in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer primer

M & L applying two coats of synthetic enamel paint over a coat of prink primer on wood or wood based material over 10 cm width or girth including preparation of new wood surface or previously untreated surface any description.

Dismantling boarding, any description, fixed in any position with nails

M&L Anodised aluminium snap grid frame work for false ceiling all as specified

S&F 12mm Medium density fibre board ISI marks, exterior grade, fixed to timber framework with screws to frame work complete all as spd

Demolition of stone masonry built in cement mortar incl coping of any description all as specified and directed.

M&L squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 all as specified.

ditto - as per item as above, but except stone

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified.

M & L for Keyed pointing to rubble masonry uncoursed or brought up to courses in cement mortar 1:4.

M and L for preparing RCC roof surfaces with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particle and providing 10 mm thick cement plaster in CM (1:3) using water proofing compound @ 3 % by weight of cement and applying one coat of bituminous primer @ 200 gms per Sqm and then laying 3mm thick APP modified bituminous membrane (mineral finish) weighing not less than 3.5 Kg/Sqm reinforced with non woven polyster mat as reinforced weighing not less than 160 gms/Sqm laid by torch application method overlap while torching shall be 75 mm on length and 100 mm width side ,all angles and bituminous should sealed with extra care to ensure full bondage all joints and changes should covered with CM 1:3 with water proofing chemical as per manufacturer's instructions and cured well before laying membrane including two coat of aluminium paint above membrane all as directed and specified by Engineer in charged.

M/S JAGDAMBA ENTERPRISES

GEMRARAMCONTRACTOR

Dadhich Engineers

Bhawani Constructions

M/S MAYA CONSTRUCTION COMPANY

AMBEY MAA CONSTRUCTION COMPANY

Leelashah Enterprises

M/S RAM NIWAS BISHNOI

M/s Shri Inder Construction Company

S R ENTERPRISES

S K TRADER