REPAIR TO VARIOUS TYPES OF WOODEN FURNITURE FOR MARRIED ACCN AND MISC WORKS AT AF STN GWALIOR

Amount

CHAIR DINNING CUSHIONED LONG BACK. M&L for repair & replacement of the following part without disturbing the other component incl tightining of frame all specified and shown on drg. FD-E6/MAP/10 & Spl

Teak wood strips 04 Nos. size 15x30x500 mm shall be provided to strength of back side support.

S&F of Teak wood rails of all side 65x25x450 mm

S&F of Teak wood legs 25x40x900 mm

S&F of Teak wood stiffener of 20x25x450 mm

S&F of Teak wood wooden stopper 20x50 mm

S&F of Teak wood front leg 30x40x400mm

S&F of 30 mm THK 32 Density foam with leatherite upholstry. Make of foam Sleepwell/Rajfoam

S&F of 12 mm TH BWR phenol bonded plywood

S&F Seat & back shall be 75mm thick 32 density foam with fabric on seat of 12 mm thk ply seat as approved by GE.

S&F of Nylon Buffre

Polishing old and new surface of chair Dining long back after repair with French polish including preparation of surface all as shown on drg and directed by Engr-in-Charge

REPAIR TO CHAIR WOODEN BOTTOM W/O ARM M&L for repair & replacement of the following components of chair wooden bottom w/o arm without disturbing the other components including tighting of frame all as specified and shown on drg :- FD-225, FD-285

S&F ply wood commercial type 6mm thick BWR Make-Century Ply/Green Ply/Kitply for seat with perforation

Back leg (Teak Wood ) left/right

Front leg (Teak Wood) left/right

Side rail (Teak Wood) left/right

Front/back rail(Teak Wood)

Wooden back strip (Teak Wood)

Stiffener (Teak Wood)

Polishing old and new surface of chair wooden bottom w/o arm after repair with French polish including preparation of surface all as shown on drg and directed by Engr-in-Charge

REPAIR TO CHAIR DINING/CBB M&L for repair & replacement of the following components of chair dining without disturbing the other components including tighting of frame all as specified and shown on drg :- FD-16(M), FD-203, FD-228, FD-279

Back leg (Teak Wood) left/right

Front leg (Teak Wood) left/right

Side rail (Teak Wood) with holes for cane weaving, spacing of holes shall match with the existing rail on the other side(left/right)

Front/back rail(Teak Wood) with holes which shall match with the holes of existing rail on the other side

Back strip (Teak Wood)

Stiffener (Teak Wood)

Polishing old and new surface of chair dining after repair with polish including preparation of surface all as shown on drg and directed by Engr-in-Charge

Recaning shall be done with 2mm wide plastic cane half round and 4mm wide plastic cane half round for lining around. The canning shall be Standered pattern and as per approval of Engineer-In-Charge.

REPAIR TO CHAIR WRITING/CHAIR OFFICE M&L for repair & replacement of the following components of chair writing/chair office without disturbing the other components including tighting of frame all as specified and shown on drg :- FD-20(M), FD-148(M), FD-271/88, FD-280

Back leg (Teak Wood) left/right

Front leg (Teak Wood) left/right

Side rail (Teak Wood) with holes for cane weaving, spacing of holes shall match with the existing rail on the other side(left/right)

Front/back rail(Teak Wood) with holes which shall match with the holes of existing rail on the other side

Back strip (Teak Wood)

Arm rest (Teak Wood)

Stiffener (Teak Wood)

Polishing old and new surface of chair after repair with French polish including preparation of surface all as shown on drg and directed by Engr-in-Charge

Recaning shall be done with 2mm wide plastic cane half round and 4mm wide plastic cane half round for lining around. The canning shall be Standered pattern and as per approval of Garrison Engineer.

REPAIR TO CHAIR DINING JCOs/ORs M&L for repair & replacement of the following components of chair dining (JCO/ORs) without disturbing the other components including tighting of frame all as specified and shown on drg :- FD/MAP-II/05

Back leg (30x55) (Teak Wood) left/right

Front leg (30x55) (Teak Wood) left/right

Side rail (Teak Wood) left/right

Front/back rail(Teak Wood)

Back strip (45x15 out of 45x35) (Teak Wood)

Stiffener (20x25) (Teak Wood)

Polishing old and new surface of chair dining after repair with polish including preparation of surface all as shown on drg and directed by Engr-in-Charge

Refixing of PVC sheet 4 mm thick with holes and screwed with frame. The PVC Sheet shall be Standered pattern and as per approval of Engineer-In-Charge. Make : Cello/Amko

Nylon Buffer of Front/back leg.

REPAIR TO TABLE WORK BENCH WORK SHOP M&L for repair & replacement of the following components of table work bench work shop and steel fram fram with hard wood top 1500x900x760 and 1800x900x760 disturbing the other components including tightening of frame by using sikanja all as specified & shown on drg. FD-301

Top made of hard wood 2nd class 25-40mm thick duly covered with all 1 mm thick GI sheet/Alluminium and top coverd with around 6 mm thick teak wood beading and directed by Engineer-in-Charge..

Legs made of teak wood as per drg.

Stiffer of teak wood as per drg.

Long Rails of teak wood as per drg

Short Rails of teak wood as per drg

Removing U/S drawer. S & F new drawer unit as per FD without disturbing to other component all as directed.

Polishing old and new surface of Table work bench work shop after repair with polish including preparation of surface all as shown on drg and directed by Engineer-in-Charge.

REPAIR TO TABLE (3050X1220X760) M&L for repair & replacement of the following components of table with hard wood top 3050x1220x760 without disturbing the other components including tightening of frame by using sikanja all as specified & shown on drg. FD-290

Top made of MDF board 18/19 mm thick duly covered with 4 mm TW beading and directed by Engineer-in-Charge..

Legs made of teak wood as per drg.

Stiffer of teak wood as per drg.

Long Rails of teak wood as per drg

Short Rails of teak wood as per drg

S&F of hard rubber ring TOE

Polishing old and new surface of Table after repair with polish/paint including preparation of surface all as shown on drg and directed by Engineer-in-Charge.

REPAIR TO TABLE M&L for repair & replacement of the following components of table hard wood top 1520x860x760 without disturbing the other components including tightening of frame by using sikanja all as specified & shown on drg. FD -289

Top made of MDF board 18/19 mm thick duly covered with 4 mm TW beading and directed by Engineer-in-Charge..

Legs made of teak wood as per drg.

Stiffer of teak wood as per drg.

Long Rails of teak wood as per drg

Short Rails of teak wood as per drg

Polishing old and new surface of Table after repair with polish/paint including preparation of surface all as shown on drg and directed by Engineer-in-Charge.

M/s Manish Contractor

M/s Pal Construction

M/s Sohan Singh Mathur