Addn/altn to bldg No. P-15, provn of misc E/M works in certain OTM bldgs and misc B/R and E/M works at various locations at AF Station Deolali

Amount

Demolition of cement concrete (unreinforced) in ground floors (below or above ground level ) not exceeding 15 cm thickness and including removing demolised PCC from site exc 500 mtr but n exc 1500 Mtr depositing where directed.

Excavation in trenches n. exc 1.50 m wide and n.exc 1.50m in depth for foundation shafts, wells, manholes etc n.exc 10 Sqm on plan and n.exc 1.50M in depth and getting out in any type of soil , complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40mm graded aggregates) as in foundation filling and mass concrete all as specified and as directed.

Reinforcement cement concrete M-25 (Design mix) 20mm graded aggregates as in foundations including rafts, footings, foundations beams, plinth beams, bases for columns and basement slabs etc complete all as specified and directed.

Reinforcement cement concrete M-25 ( Design mix) 20mm graded aggregates as in columns, pillars, piers, posts and struts etc complete all as specified and directed.

Reinforcement cement concrete M-25 ( Design mix) 20mm graded aggregates as in beams, cantilever, bressummeres lintels over 1.50m span complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, including flat rough finished surafaces of concrete complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns, and stanchions, square, rectangular or polygonal in shape, including flat rough finished surafaces of concrete complete all as specified and directed.

Form work to sides and soffits of floor and roof beams, beams haunching, girders, bressummers, lintels and cantilever, shelves including supports over hangs etc rough finished surfaces of concrete ( flat ) complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

Mild steel TMT bars 6 to 10mm dia ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, (as in stirrups) hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-310-O or Fe-410-O all as specified & directed.

Brick work with fly ash bricks (Old Size bricks) straight or curved on plan exc 6 mtr mean radius built in CM (1:6) all as specified and directed

M&L rendering 15mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed

M&L Rendering 15mm thick cement plaster on other than fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed

Taking down cement plaster on brick/stone walls/ concrete surface etc including raking out joints, hacking for key, scrubbing down with water etc all as directed.

M & L for rendering 10mm thick over 10mm thick rendering (as in backing course) on stone masonry surfaces of walls in cement mortar 1:6 finished even and smooth (without using extra cement) all as specified and directed.( Note : Rendering should be done in two layers)

M & L for preparation of new plastered surface of wall by applying 2mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper complete all as specified & directed.

Complete removal of existing treatment of walls by steel wire brushing, prepariation of surfaces and applying two coats of distemper oil emulsion after chalk whiting or JK wall care putty 2mm thick over the walls all as specified and directed by Engineer-in-Charge.

M & L for providing 100mm thick cement concrete type B-2, 1:2:4 (using 40mm graded stone aggregates as in floor all as specified and directed by Engineer-in-Charge.

M & L for providing cement concrete type B1 1:2:4 (12.5mm graded aggregaes) in bed plates, coping, roof/window chajjas kerbs or mud stops, rounded or chamferred on edges etc all as specified and directed.

S & F rolled mild steel angle/tubular/square/rectangular roof trusses (framed), trussed purlins, rails and fastenings and heavy bracket framing, confirming to Fe 410 - W (Grade-E-250) including distance pieces, cleats, etc., complete all as specified and directed..

S&F Framed work such as grills, gratings door chowkats etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

M&L preparation of new steel surfaces of any description over 10 cm in width or girth not other wise described and applying two coats of synthetic enamel paint over one coat of red oxide all as specified and as directed.

Returning filling in including spreading, levelling,watering and well ramming in layers not exceeding 25cm thick all as specified and as directed.

Removal of surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding and depositing where directed at a level not exceeding 1.5m above the starting point all as directed.

M & L for false ceiling work of aluminium snap grid system size 605x605mm for false ceiling with aluminium angles of size 23.5 mmx23.5,,x1.5mm fixed to wall with GI screws and aluminium tee of size 37.5x37.5x1.5mm in main and cross runners fixed 60 cm c/c and tied to existing roof/truss/rafters complete

M & L for hanging of aluminium false ceiling grid with 3 mm dia GI wire(upto necessary required length & 1.2 Mtr c/c) fixed to slopping roof (rafter/purlin/trusses) complete all as specified.

M & L Non asbestos fibre cement building boards 4 mm thick (one side embosed design), fixed or laid/ inserted to Aluminium grid frame work in ceiling with clips all as specified and directed.

M & L for 3mm thick poly carbonate translucent corrugated/plain sheeting with two corrugations side lap fixed with coatch screw and washer in roof, wall etc fixed with L-type or cranked hook bolts in lieu of screw all as specified and directed.

Cutting openings through stone walls built in cement mortar for door, windows and other openings for inserting roof truss etc or enlarging existing openings etc or cutting out defective masonry for underpinning including providing, fixing and removing shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises all as specified and directed by Engineer-in-Charge.

M & L for plain/reinforced cement concrete type B-1, 1:2:4 (using 20 mm graded granite stone aggregate) cast in situ in copings, bed plates and the like including weathering, slightly rounded or chamfered angles & throating and including use of necessary form work all as directed.

Taking down chowkats or frames with shutters not exc 1.5 sq.m (without taking off shutter from the frame) all as directed.

S&F Anodised powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators 114.30 mm x 44.45 x 3.18 mm with one or more rebates including jointing cleats for fixing etc complete all as specified and directed.

S&F Anodized aluminium door shutters powder coating (any colour decided by GE) of thk not lesss than 50 micron, aluminium section in which size of shutter top members 47.62 x 44.45 x 3.18 mm , shutter bottom member 100 x 44.45 x 3.18 mm , shutter vertical members 47.62 x 44.45 x 3.18 mm and shutter lock rail member of size 63.50 x 44.45 x 2.40 mm including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos each door, hinges, anodised aluminium snap beading screws etc complete all as specified.

S&F Anodized aluminium powder coated window and ventilator shutters, glazed/gauzed shutter having stile and rails size 44.60 x 30.00 x 3.18 mm thick with triangular aluminium beading of 15 mm size side hung/sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings, such as peg stays 150 mm long (1 No), hinges type B-21 100 mm long (2 Nos) suitable handle (1 No) complete all as specified and as directed.

S&F 5.5 mm thick frosted sheet glass, ordinary quality and glazing with oil putty in squares exc 0.5 Sqm in each pane all as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks, or stainless steel wire staples all as specified & directed.

S&F double action floor door stopper/spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation bore, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty all as specified and as directed.

S & F aluminium (die cast) body door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters of 851 to 1000mm in width & weight between 61 to 80 Kg and fixed all as specified and directed.

S&F Mortice lock brass 100 mm 4 lever vertical type fixed.

S&F for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed.

Supply only pre -coated fancy type drapery 25mm dia fixed with fancy type matching pair of brackets fixed with screw (Note : Brackets will be measured and paid for seperately)

S & F fancy type brackets to suit pre-coated curtain rod 25mm dia

Exacavating over area n.exc 1.50M deep and getting out any type of soil all as specified and directed .

All as per item No. 44 above but beyond 1.50m in depth.

Surface dressing n.exc 15 cm deep in any type of soil all as specified and directed.

Removal of surplus soil to a distance not exceeding 250M but n.exc 500M and depositing where directed at a level not exceeding and depositing where directed at a level not exceeding 1.5m above the starting point and disposal.

Brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius for manhole/septic tank etc built in CM (1:4) all as spd and directed

Brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius for manhole/septic tank etc built in CM (1:6) all as spd and directed

M & L for brick work with sub class 'B' brick, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 all as specified and directed.

M & L for rendering 15 mm thick in CM 1 : 4 on fair faces of brickwork or concrete surface finishing the surface even and smooth without using extra cement.

M&L for rendering or plastering work 10mm thick in CM 1:3 in fascia / edging / ceiling of Chajjas, roof projections etc, including taking out peeled off plaster / concrete and making the line in true shape and finishing the surface without using extra cement.

Preparation of new plastered surface of external wall and chajjas and making the surface smooth with sand paper and priming the surface with alkali resistance primer paint for external surface, over primed surface applying two coat of cement base paint incl curing complete all as specified & directed.

Preparation of old surface after complete removal of existing treatment applying 2mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper complete all as specified & directed.

M & L Cement concrete 1 : 2 : 4 type B1 (using 20 mm graded stone aggregate) as surface channel and drains.

Extra for forming fair finished drain or channel 30cm inner grith in cement concrete, using extra cement, including forms, moulds, mitred/stop ends etc.

M&L concrete bed to drain pipes incl forming cadles in cement concrete 1:3:6 type C2 for 200 mm dia pipe.

S&F salt glazed stoneware gully traps, squar or round mouthed, type 'P' of size 180x110.

M&L 150 Salt-glazed stoneware drain pipes laid in trenches and jointed as specified and directed.

Cutting into existing manholes for connecting new drains/sewage line pipe of 150mm internal dia pipe, making good to pipe and rendering cutting out existing benching for and forming branch channel1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming bencing as required.section) all as directed.

S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frames shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom railon either side and as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification & drawing.

All as per item No. 62 above but wire gauzed i.e panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8 mm MS solid tube and this tube shall be welded to MS tubes. The wire gauze shall be stretched to tighten firmly, complete all as specified and as directed.

S&F aluminium powder coated window and ventilator shutters fixed type without sash bar, aluminium section weighing 0.55 Kg/M including necessary joining cleats, glazing clips, rubber packing, aluminium snap beading powder coated, screws etc complete all as specified and directed by Engineer-in-Charge.

S & F plain sheet glass 5 mm thick tinted, fixed to aluminium doors/ windows / ventilators complete all as directed by Engr-in-Charge (Note:- Beading/rubber packing is included in the rates for aluminium sections above.)

Provision of aluminium grill in panelled of Deco grill model No DG-902 or equivalent with required aluminium frame of size 65 x 1.5 mm thick including necessary joining cleats, rubbers packing and aluminium beading screws etc complete all as specified & as directed by Engr-in-Charge.

S & F 1.25mm thick mild steel, plain, black sheet in wall cladding, steel gates, etc., cut to size, holes punched including rounded headed screws, clout nails or revets and fixed to wood or steel framing or fixing to MS clamps with necessary bolts and nuts with plain 40mm lap joints welded to frame as directed.

S&F 100 mm long stainless steel Butt hinges, medium weight, cold rolled and fixed all as specified.

Cement concrete type C-1, 1:3:6 (using 20mm graded aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair incl making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight and complete all as specified

Hardcore of guage exc63mm,Broken Stones or Boulders deposited, spread & leveled in layers n exc. 15 cm thick, watered & rammed to a true surface

M&L for 75 mm thk PCC 1:4:8 type D-2 as in subbase to flooring.

M&L Chequered cement concrete tiles rubber moulded 25cm x 25cm x 25mm thick set, jointed and pointed in near cement slurry in floors, with grey cement and pigments over and including 15 mm thick screed bedding in CM 1:6 all as specified and directed.

M & L glazed coloured (digital/printed/design) ceramic tiles in vertical surface 450 mm x 300 mm x 7mm thick 450 mm x 300 mm x 7mm thick or set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 10 mm thick rendering in CM 1:4 including taking down cement plaster complete all as specified and directed

M & L for machine cut cudappa stone slab 30-40mm thick as in slab/vertical pillar over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

M&L 20 mm thick Granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills cooking platforms & like in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite over 15 mm thick cement screed/rendering in CM 1:4 including Roughening surfaces of old/new concrete floor/wall by picking,sweeping clean and washing down with water to remove dust etc and brusing neat cement slurry with 3.00 kg per sqm all as spd & directed.

Round chamfering, to the edges of granite/mirror finished kota stone n.exc 15mm wide on granite stone shelves.

Precast Reinforced cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) set in cement mortar 1:4 as in slab for water tank/shelf, landings, cover slabs (for man holes etc) chullah hoods, chajjas, water trough, managers, shelves & similar articles with plain faces all as directed.

S&F 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc all as specified.

M&L cutting chases with diamond cutter pinning in brick mas and making good to facing where required and pointing in cement and making good in CM 1:3 cutting n.exc. 10 cm in girth.

S&F 25mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc all as specified.

S&F Bib taps for 15 mm bore pipe, cast copper alloy fancy type chromium plated fixed of Make - Jaquar , Marc and Johnson complete all as specified and directed.

S & F Vitreous china wash basin counter top oval type , white flat back,size 550 x 400 mm including waste pipe , brackets and cutting for and pinning in ends of brackets or errecting stand and 32 mm dia PVC waste pipe fixed including waste copling 32mm size full thread , all as specifiedd and directed

S&F 15mm bore pillar cock fancy type, screwed down high pressure with or without letters hot or cold with long screwed shank and fly nuts screwed for iron pipe ISI marked complete all as specified & directed.

S&F towel rail CP 600 mm long complete all as specified and directed.

S& F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass sheof 12cm wide with chromium plated brackets guard & railing 60cm long

S&F Liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 105 gms)

PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. Make:Paryag/Polytech

Rotational moulded polyethlene water storage tanks of capacity 1000 litres three layers (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete including 20mm dia ball brass valve high pressure with polythene float and dismantling of existing PVC tank of any capacity complete all as specified & directed.

S&F 15 mm size gun metal globe or gate valves with iron wheel head, screwed both endsfor iron pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butter fly handles screwed down screwed for iron pipe of 15 mm bore.

S&F 25 mm size gun metal globe or gate valves with iron wheel head, screwed both endsfor iron pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butter fly handles screwed down screwed for iron pipe of 25mm bore.

S&F CI floor trap 75 mm with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 with CP grating with ot without hole for waste pipe complete all as specified.

M&L for point wiring complete with two single core, PVC insulated, unsheathed, multi stranded bright annealed copper conductor cable, 1.5 Sq.mm 1100 Volts, FR grade drawn through and including heavy duty PVC casing and capping not less than 25 mm width and accessories surface mounted on walls, ceilings etc. on & including PVC board with earth dolly arrangement with surface plate for mounting switches, sockets, regulators etc and one run of 1.5 Sq.mm PVC insulated, unsheathed, multistranded, copper conductor cable FR grade as earth wire and connected to common earth dully complete for the following :-

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One bell point controlled by one push button.

(d) One 3 pin socket out let 5 Amps on Same board.

(e) One 3 pin socket out let 5 Amps on independent board.

All as per Sl item No 93 above but with two runs of 2.5 Sq.mm cable and one run of 1.5 Sq.mm cable as earth wire for one 3 pin socket outlet/power point 15 Amps controlled by one switch.

Supply & fix switch piano flush type single pole one way 5 Amp.

Supply & fix switch piano flush type single pole one way 15 Amp

S&F Fan regulator electronic solid state with various steps variable speed suitable for ceilling fan of size 900 to 1500mm sweep working on 230 V AC supply with all necessary connections

S&F Bell push 5 Amps SP one way suitable for 230 Volts flush type.

S&F electric bell Ding Dong AC 230 volts single pole.

Supply & fix Socket out let 2 in 1, 5 pin 5 Amps flush type.

Supply & fix Socket out let 2in1,3 pin 5 and 15 Amps flush type.

S&F ceiling rose,3 phase/ PVC /polycarbonate isolated body,65x50 mm two to three terminals

S&Fceiling light fittings 36W LED energy saving, environmental friendly long life and accessories fixed false ceiling 60 cm x 60 cm in size including connection with PVC copper 1.5 sqmm 3 core cable etc complete all as directed. Make crompton Model No LCTLRN-36-CDL or equivalent in Phillips, Havells, Wipro or approved makes by HQ CESC pune as approved by GE

S&F exhaust fan AC single phase 230Volt of size 300mm sweep with lauvers, complete all as directed. Make: Havells (Ventil Air DB) or equivalent in Crompton, Khaitan, Usha, Bajaj, Almonard or approved makes by HQ CESC pune as approved by GE

S&F sheet metal enclosures Distribution board 415 volt, Vertical TPN 4 way with provision for DPx160 series MCCB of legrand make or equivalent in L&T as incomer and SP/TP MCB's as outgoing as per IS including compact insulated bus bar and rounded neutral bar, door earthing complete double door surface/reccess mountingIP-43 IK-09 protection with the following :- (i) MCCB DPx160 series thermal magnetic, 25 KA rupturing capacity,125A, 4 pole as incomer-01 Nos (ii) MCB SP 6 to 32 Amp,10 KA - 10 Nos.

S&F sheet metal enclosure 8 way MCB SPN distribution board 240/415 volt, double door with DIN rail bus bar, neutral link, earth terminal etc IP-43, IK 09 protection Make- L&T or equivalent as approved all as specified and directed by Engr-in-Charge.

S&F sheet metal enclosure 4 way MCB SPN distribution board 240/415 volt, double door with DIN rail bus bar, neutral link, earth terminal etc IP-43, IK 09 protection Make- L&T or equivalent as approved all as specified and directed by Engr-in-Charge.

S&F MCB SP 6-32 Amp single phase 240 volts including making connection complete all as specified.

S&F MCB SPN 6-32 Amp single phase 240 volts including making connection complete all as specified..

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to GI wire 4 mm dia through GI pipe 15 mm dia light grade by means of bolts,nuts, check nuts and washers of galvanised iron or steel,with adequate quantity of charcoal and salt, proper watering arrangements including 20 mm dia medium grade GI tubing.PCC chamber,Chamber Cover all as shown in electrical plate no 3of SSr part I 2009 connected to earthing test point all as specified or indicated and testing on completion. The end point connection of eatrhing will be carried out with the help of GI bolt grouted and washer and nut.

Supply and fix LT XLPE insulated & PVC heavy duty armoured cable 1100 volts grade UG multi stranded aluminium conductor electric cable cross sectional area 6 Sqmm 2 Core including necessary connection with provision of lugs & cable gland fixing arrangements all as specified and directed.

S&F power shield (mini MCB with enclosure) with DP, 32 Amp single phase 240 volts including making connection complete all as specified.Make: Standard: cat.no. DSMPCDPA032 or equivalent of L&T/HPL or approved makes by HQ CESC pune as approved by GE

Supply & fix fans ceiling complete with electronic type regulator and accessories 230 V,1200 mm sweep. BLDC fan including connection with PVC copper cable 1.5 sqmm 3 core etc complete all as directed. Make- Havells(Model ES Neo) or equivalent in Bajaj, Usha, Crompton or approved makes by HQ CESC pune as approved by GE.

Supply and install Cassette type AC units indoor/outdoor complete with cordless remote control unit , scroll compressor, three phase units 440V - 660V, 50 Hz of capacity 4.0 TR copmplete all as directed. Make- Blue star, Hitachi, Carrier, Lloyd or approved makes by HQ CESC pune as approved by GE.

Supply & fix Air Circulator fans 230 volts single phase oscillating 450 mm sweep suitable for wall mounting. Make- Havells (Turbo force) or equivalent in Almonard, Crompton, Bajaj, Usha or approved makes by HQ CESC pune as approved by GE

S&F Sub main wiring with PVC insulated un armoured heavy duty copper conductor 1100 Volts FR grade 2 single core 2.5Sq.mm cable and one run of 1.5Sqmm copper earth wire for continuous earth fixed on wall/ceiling/floor etc. drawn in PVC casing capping/ PVC non metallic conduit complete all as specified and as directed by Engr-in-Charge. Note: Two run of 2.5Sqmm cable, one run of 1.5Sqmm cable and one run of PVC casing capping/PVC non metallic conduit shall be measured as one unit length.

S&F wall fan 230V, 400mm sweep with all connection arrangements & necessary nut bolts etc including wall fixing arrangements & connecting with flexible wire of size 23x0.0076 for connecting up to ceilling rose all as directed by the Engr-in-Charge. Make Havells(Model : Swing, Single phase or equivalent in Usha, Bajaj, Crompton, Phillips as approved by GE).

Supply and fix electric water heater storage vertical type of capacity 25 litres of high energy saving with multiple safety including all fixing arrangements all as directed. Make- Havells, Racold, Crompton, Usha or approved makes by HQ CESC pune as approved by GE

Supply & fix heavy duty exhaust fans AC single phase 230/ 240 V of size 300 mm sweep, 1400 rpm with louver with all connection arrangements and necessary nut bolts etc including wall cutting and making good disturbed surfaces if necessary and connecting with flexible wire of size 23x0.0076 for connecting upto ceiling rose all as directed by Engr-In-Charge. Make: Havells (Model: Turbo force) or equivalent in Almonard, Crompton, Bajaj, Usha or approved makes by HQ CESC pune as approved by GE

Supply & fix heavy duty exhaust fans AC single phase 230/ 240 V of size 380 mm sweep, 1400 rpm with louver with all connection arrangements and necessary nut bolts etc including wall cutting and making good disturbed surfaces if necessary and connecting with flexible wire of size 23x0.0076 for connecting upto ceiling rose all as directed by Engr-In-Charge. Make: Havells (Model: Turbo force) or equivalent in Almonard, Crompton, Bajaj, Usha or approved makes by HQ CESC pune as approved by GE

S&F flood light fittings 140 watt LED energy saving, environmental friendly long life versatile die cast aluminium housing with IP 66 protection, 10 KV external SPD with high power LED and acessories fixed on existing/new GI pipe bracket fixed on HT/LT poles and connection with PVC aluminium 1.5 sqmm 3 core cable etc complete all as directed. make: Crompton Cat Part No: LFLN11-140-CDL/60 or equivalent in Philips, Havells, wipro, Bajaj or approved makes by HQ CESC pune as approved by GE

S & F 18W all in One Solar Street Light IP65 Protection, 20 W (120 lm/watt) 6000k-6500k including inbuilt Solar Panel 40 W (Monocrystalline SPV modulel),20*1 LED Panel, CRI > 80% 5000 burning hr LED lamp life, Battery Lithium-Ion (LifePO4) 12.8 V 21 AH, Including necessary fixing bracket, nut, bolt & washer etc. complete. Make: Havells Cat Ref: SSSSLX0136 or Equivalent in Bajaj/Tata BP Solar India/ BHEL Note:- Ther serviceability of solar street light will be maintained for minimum two years under supervision of OEM.

Supply and laying, fixing, tube galvanised medium grade 40mm dia with all fittings laid in tenches/Fixing on wall/pole including fixing arrangements like clamp, nut and bolt etc all as directed.

SHREE SAMARTH SERVICES

SHRI SULAI ELECTRICALS

M/s.NIKI ENTERPRISES

MAHIMA CONSTRUCTION