ADDNALTN TO P-338 OF 8 BIHAR AND P-67 OF 100 MTN BDE AT SEVOKE ROAD MIL STN UNDER GE SEVOKE ROAD

Amount

Schedule 'A'

Dismantling plain or corrugated galvalume aluminium zinc sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding/ eaves board fixed with selp tapping screw complete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding/eaves board fixed with selp tapping screw complete all as specified and directed.

S & F Mild steel work in framed brackets of angles or tees with web and flanges cut to shape, drilled and counter sunk for screw, including bending and welding angles as necessary gusset plates; riving etc n'exc 10 Kg each brackets conforming to Fe-290 Gde-165 complete all as specified and directed. .

S & F Framed work as in tubular posts roof trusses, purlines, rafters etc made of tubes (square circular oval or any other shape or section as directed) including all necessary fittings, nut bolts, threading or welding etc as required for completion of work complete all as specified and directed.

Taking down cement plaster or any description including raking out joint, hacking for key scrubbing down with water etc and removal of debris out side MD land complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished fair and even without using extra cement complete all as specified and as directed.

M&L for 20mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layer of 10mm each mixed with water proofing compound in top layer @ 3% by the weight of cement or as per manufacture's instructions finishing the surface fair and even without using extra cement complete all as specified and as directed. (Note:- Water proofing compound shall be measured and paid separately under relevant item of this schedule 'A')

M&L for 15mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layer of (10+5)mm mixed with water proofing compound in top layer @ 3% by the weight of cement or as per manufacture's instructions finishing the surface fair and even without using extra cement complete all as specified and as directed. (Note:- Water proofing compound shall be measured and paid separately under relevant item of this schedule 'A')

M&L for rendering 5 mm thick in CM 1:3 as in ceiling finished even and smooth without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and directed.

S&F of galvanised steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with galvanised steel wire staples complete all as specified and directed.

M&L for 2-3 mm thick wall care putty on internal surface of wall of new/old surface complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with roller over a coat alkali resistant primer complete all as specified and as directed.

M&L for complete removal of existing treatment of wall by booming down or steel wire brushing scrapping down to remove smoke soot moulds moss and efflorescence salts and treating oil and greasy spots etc and applying two coats of oil bound distemper with roller over a coat alkali resistant primer complete all as specified and as directed.

M & L for preparation of new plastered surfaces of wall and applying applying one coat of Primeseal primer of M/s Dr Fixit or equivalent chemical of M/s STP Ltd as approved by the GE or one coat of Chemstic PDE 600 elastomeric coating (and allowing to dry for 8hrs) under torch dry condition and subsequently applying two coats of water proofing decorative elastomeric coating system Raincoat of M/s Dr Fixit with DFT 100microns or Shalicryl 215 of M/s STP Ltd or Chemstic PDE 600 elastomeric coating (the surfaces after painting one coat shall be allowed to dry for 6 to 8hours before application of next coat) including necessary scaffolding etc complete all as per manufacturer instructions complete all as specified and as directed Note: The aforesaid treatment shall be got executed by the contractor from the authorised applicator of the manufacturer(s) and also necessary authenticated documents on account of above shall be submitted by the contractor to the GE.

M&L for complete removal of existing treatment of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots including washing down water etc. applying applying one coat of Primeseal primer of M/s Dr Fixit or equivalent chemical of M/s STP Ltd as approved by the GE or one coat of Chemstic PDE 600 elastomeric coating (and allowing to dry for 8hrs) under torch dry condition and subsequently applying two coats of water proofing decorative elastomeric coating system Raincoat of M/s Dr Fixit with DFT 100microns or Shalicryl 215 of M/s STP Ltd or Chemstic PDE 600 elastomeric coating (the surfaces after painting one coat shall be allowed to dry for 6 to 8hours before application of next coat) including necessary scaffolding etc complete all as per manufacturer instructions and all as specified & directed. Note: The aforesaid treatment shall be got executed by the contractor from the authorised applicator of the manufacturer(s) and also necessary authenticated documents on account of above shall be submitted by the contractor to the GE.

M&L for for preparation of newly ceiling plastered surfaces and applying three coats of whitewash on wall complete all as specified and as directed.

M&L for complete removal of existing treatment and applying two coat of white washing on ceiling surface complete all as specified and as directed

M&L for complete removal of existing treatment and applying two coat of white washing on wall surface complete all as specified and as directed

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store, and rubbish off the premises complete all as specified and as directed.

M & L for roughening surfaces of old concrete floor by picking sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3 kg of cement per sqm complete all as specified and as directed

M&L for machine cut kota stone slab 20-25 mm thick (size not less than 55cm X 55 cm) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including cement screed bed 20 mm thick in cement mortar (1:6), complete all as specified and as directed.

M&L for machine cut kota stone slab 20-25 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing as in skirting over and including 10mm thick backing layer in cement mortar (1:3) on brick work or concrete surface, complete all as specified.

Demolition of reinforced cement concrete work(chimney, kitchen platform etc) of any description and in any position not otherwise specifically provided for complete all as specified and as directed

M&L for RCC 1:2:4 type BI (using 20 mm graded stone aggregate) nominal mix as in kitchen slab, fins, facia etc complete all as specified and as directed.

M&L for 20mm thick granite slabs of any type (table rubbed and polished) on cooking platforms set and jointed in net cement slurry and pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including necessary moulding at edges laid over and including 20mm thick cement mortor screed bed in cement mortor (1:6) complete all as specified and as directed

M&L for 20mm thick granite slabs of any type in skirting/ dado laid over cement screed bed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including necessary moulding at edges laid over and including 10mm thick cement mortor screed bed in cement mortor (1:3) complete all as specified and directed.

M&L Non - skid Ceramic tiles(colour) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and 15mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed.

M&L for glazed ceramic tiles coloured of size 450 x 300 x 7 to 8mm thick as in dado, skirting. riser to steps, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of the tiles complete all as specified and as directed with 10 mm screed bed 1:4 for laying wall finishes complete all as specified and as directed.

M&L Non - skid Ceramic tiles(colour) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and 15mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed.

M&L for coloured ceramic tiles 7 to 8mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in ditto/skirting etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick cement mortar screed bed in CM 1:6 etc, complete all as specified and directed.

M&L for vitrified Non-skid ceramic tiles 10 mm thick (square/ rectangular) polished size, area of each tile exceeding not exceeding 0.36 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 20mm thick cement mortar screed bed in CM 1:6 etc, complete all as specified and directed.

M&L for vitrified Non-skid ceramic tiles 10 mm thick (square/ rectangular) polished size, area of each tile exceeding not exceeding 0.36 Sqm as in datto/skirting etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick cement mortar screed bed in CM 1:4 etc, complete all as specified and directed.

Taking down chowkhats or frame exc 1.5 sqm but n exc 4 sqm but with shutters (without taking off shutters from the fame) and refixing of old shutter in new chowkhats complete all as specified and directed by Engr in Charge.

Taking down chowkat or frame Chowkhats or frames not exc. 1.5 Sqm each but with shutters (without taking off shutters from the frame) complete all as specified and as directed.

S&F Second class Hard Wood (SAL/Hollock/Kalasiris) plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints etc complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and as directed.

S&F factory made solid panel PVC door shutters 30 mm the style size consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC C channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail , paneling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading ,and joined together with solvent cement & fix in the frame at site complete all as specified and as directed.

M & L pressed steel door frame of size 105mm x 60mm (thickness of profile 1.25mm) with one or more rebates including necessary fixing lugs , hinges, lock strike plate etc complete all as specified and as directed.

M & L pressed steel door frame of size 125mm x 60mm (thickness of profile 1.25mm) with one or more rebates including necessary fixing lugs , hinges, lock strike plate etc complete all as specified and as directed.

M&L for PCC (1:3:6) type C-1 with using 20mm graded stone aggregate as in bed blocks, coping, for fixing holdfast/lugs, filling hollow space of pressed steel door frame etc including necessary form work complete all as specified and as directed.

S & F factory made 35mm thick plain, framed panelled shutter (two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm veneered particle board with commercial veneering in both faces. The size of rails and stiles shall be as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated of 2nd class hard wood complete all as specified and directed.

S&F factory made 35mm thick 2nd class hard wood Kiln seasoned and chemically pressure treated, glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars), edges, of framing plain, chamfered or rounded, fitted with cut and mitred bends for securing glass etc, sizes of members of shutters as specified in SSR Part I, Section 8, cluase 8.24 (a) ; supplied and fitted to chowkats complete all as specified and directed.

M & L for 18/19mm thick preliminated partical board grade 1 quality exterior grade type one side with decorative choice lamination & other side balancing with lamination fixed with screws to timber frame work as in cup board complete all as specified and as directed

M & L for 18/19mm thick block board grade 1 quality exterior grade type commercial type fixed with screws to timber frame work as in cup board shelves complete all as specified and as directed

S&F Machine cut cudappa stone slab 20-25mm thick over cement screed bed CM 1:4 10 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing as in cill/wall cladding etc complete all as specified and as directed

S&F standard aluminum section powder coded in partition / frame and door shutter, sliding windows / ventilators and places otherwise not specified cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass or wire cloth or Bakelite sheet and all necessary fittings, hinges, screws, plugs, locking arrangements for windows, Nylon ball bearing etc completed all as specified and directed Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper only will be measured and paid separately under respective items as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

S&F in repairs aluminium alloy wire cloth, 0.45 mm noimnal dia of wire and average width of aperture 1.40 mm,complete all as specified and as directed

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for 4mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc. 0.5 Sqm in each pane, complete all as specified and as directed.

S&F 5.5mm thick figured glass/pin head type and glazing with oil putty in squares not exceeding 0.50 sqm in each pane complete all as specified and as directed

S&F 100mm long stainless steel butt hinges medium weight complete all as specified and as directed.

S&F aluminium anodised bow handles of 150mm size, fabricated type of extruded section fixed with screws to shutters, complete all as specified and directed.

S&F aluminium anodised bow handles of 125mm size, fabricated type of extruded section fixed with screws to shutters, complete all as specified and as directed

S&F of 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F of 125mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and as directed.

M& L for Hasp and staple, safety type, aluminium anodised 100 mm including bolt to hinge plate and fixed with screws complete as specified and directed.

S&F in repair continuous (piano) hinges width of flaps 30mm , mild steel, bright finish or electrogalvanised complete all as specified and as directed

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for for preparation of old steel surfaces of any description or not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed

M&L for for preparation of new steel surfaces of any description or not other wise described n exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and as directed

M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Preparation of old painted wooden surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint,desigen and pattern as approved by engineer in charge complete all as specified and as directed

Demolition of Cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) including removal of debris / demolished materials to a distance exc 50m and n.exc. 250m complete all as specified and as directed.

Demolition of brick work built in CM incl. taking out roots vegetation if any at any position and removal to out side MD land complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with sub class 'B' old size bricks best quality straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

M&L for 100mm thick cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) in PCC floor finished even and smooth without using extra cement complete all as specified and as directed.

M&L for chequered cement concrete tiles 30cm x 30 cm x 25 mm thick (with grey cement and pigments), set, jointed and pointed in neat cement slurry in floor with grey cement mixed with pigments to match with the colour of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed

M&L for PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in surface channels and drains including necessary form works complete all as specified and directed.

M & L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

Add or deduct for each 25mm girth or part thereof over or under 30cm ---------------- Ditto -----------.complete all as specified and as directed.

Taking up or down GI tubing 15 mm bore pipe and connection including cleaning for refixing or removal from site complete all as specified and as directed.

Taking up or down GI tubing 20 mm bore pipe and connection including cleaning for refixing or removal from site complete all as specified and as directed.

Taking up or down GI tubing 25 mm bore pipe and connection including cleaning for refixing or removal from site complete all as specified and as directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good in brick walls, cutting not exceeding 10 cm girth complete all as specified and directed.

S&F for 15 mm bore medium grade galvanized steel water tubing concealed with all fittings and fixed to wall/ceiling or laid in floor complete all as specified as in short lengths complete all as specified and directed.

S&F for 20 mm bore medium grade galvanized steel water tubing concealed with all fittings and fixed to wall/ceiling or laid in floor complete all as specified as in short lengths complete all as specified and directed.

S&F for 25 mm bore medium grade galvanized steel water tubing concealed with all fittings and fixed to wall/ceiling or laid in floor complete all as specified as in short lengths complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittinges, heads, shoes, bends, swan-necks etc including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed

S&F in Plain, Aluminium sheeting,0.71 mm thickness Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (as in crumple joints) complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and as directed

S & F 110 mm bore PVC (SWR) branch piece single (Single `Y') equal or unequal with access door complete all as specified and as directed

S & F 110 mm bore PVC (SWR) Vent cowl complete all as specified and as directed

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and as directed

S & F 75 mm bore PVC (SWR) branch piece single (Single `Y') equal or unequal with access door complete all as specified and as directed

S & F 75 mm bore PVC (SWR) Vent cowl complete all as specified and as directed

S&F in repairs wash hand basin, vitreous china white of size 550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar taps chromium plated fancy type etc complete all as specified and directed.

S&F Stop cock/angle cock, cast copper alloy chromium plated, screwed down, high pressure with crutch or butterfly handle, fancy type chromium plate with long shank and cup complete all as specified and directed.

S&F 15mm bore bib tap cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed iron pipe or for brass ferrule complete all as specified and directed.

S&F 15 in repair mm bore basin mixture cast copper alloy with capstan head chromium plated fancy type screwed down high pressure with or without letter hot or cold with long screwed shank and flynuts screwed for iron pipe complete all as specified and directed.

S&F 15 mm bore chromium plated fancy type health faucet with 1.5m long tube with CP wall bracket complete all as specified and directed.

S&F 15 mm bore chromium plated two way bib cock complete all as specified and directed.

S&F in repair of CP brass wall mixture 3 in 1 system with provision forehead shower with long bend pipes and wall flanges with 125mm size chromium plated shower rose with swivel joint and matching CP arm complete all as specified and directed.

S & F in repairs flushing cistern, 10 Ltrs. Capacity, PVC valveless, symphonic action type with dual flushing system, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or PVC, 32mm dia, complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

Supply & fixed Shower rose swivel type brass chromium plated 125 mm size including fixing to steel pipe or unions complete all as specified and as directed

S&F towel rail 600mm long of PTMT (min weight 190 grams) fixed with and incl chromium plated brass screws and wooden / plastic cleats, complete all as specified and directed.

S&F 32mm bore high density polyethylene pipes (LDPE) of pressure rating 6 Kgf / cm2, fixed to walls, ceiling or laid in floors etc, complete all as specified and directed.

S&F sinks with drain board made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including provision of fixing cantilever brackets and connecting union to pipe, also including 40mm bore PVC waste pipe, overall size 915mm x 460mm with bowl size 410mm x 330mm x160mm, complete all as specified and directed.

S&F sinks without drain board made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including provision of fixing cantilever brackets and connecting union to pipe, also including 40mm bore PVC waste pipe, overall size 495mm x 420mm with bowl size 410mm x 330mm x160mm, complete all as specified and directed.

S&F CP curtain rails 20 mm dia chromium plated, with and including fixing brackets, stops, rollers etc, complete al as specified and directed.

S&F in repair vitreous china squatting pan "Orissa" pattern size 580x440mm white with integral foot rests(excluding flushing cistern and flush pipe) with 'P' or 'S" trap from or back inlet etc including connection to trap tend flushing pipe and provision of lime concrete bedding complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan European type with 'P' or 'S" trap from or back inlet (pedestral pattern)(excluding flushing cistern & flush pipe), white including plastic water closet seat cover, back closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F 15 mm dia chromium plated Sink mixture good quality ISI marked sample approved by GE complete all as specified as directed.

S&F PVC cabinate with mirror good quality ISI marked sample approved by GE complete all as specified as directed.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified as directed.

S&F Chromium plated soap dish Chromium plated ISI marked sample approved by GE complete all as specified as directed.

S&F toilet paper holder Chromium plated ISI marked sample approved by GE complete all as specified as directed.

S&F kitchen plate rack made out of stainless steel 1mm thick sheet with partition and size of rack 800X250X900 mm with shape and pattern as per sample kept in sample room of GE office complete all as specified and directed.

Demolition of reinforced cement concrete roofs floors (other than ground floors), beams, staircases, landings, chajjas and similar suspended work complete all as specified and directed.

M&L for Reinforced cement concrete typeB0 1:2:4, (12.5mm graded aggregate as in chajja, kitchen platform etc complete all as specified and as directed..

M 7 L for formwork to chullah hoods, slab , chajja, troughs and similar items including edges for flat complete all as specified and as directed.

M & L for removing loose, disturbed or disintegrated old concrete surfaces of RCC beam, column, lintel, pardi, railing etc, cleaning thoroughly exposed reinforcement, by sand blasting using suitable pump as directed by the GE, preparing exposed concrete surfaces to receive guniting, applying one coat of anti corrosive paint to the exposed reinforcement, supply and fix welded wire mesh of size 100 x 100 mm of 3 mm dia wire, weight not less than 1.37 Kg/Sqm & binding with 22 guage mild steel (annealed) binding wire to reinforcement and applying pressure guniting in cement mortar 1:3, minimum thickness 30 mm and thereafter rendering 10 mm thick plaster in cement mortar 1:3, mixed with water proofing compound @2% by weight of cement and finishing the surfaces even and smooth without using extra cement to match with the existing surfaces, removing the debris outside MD land including material and labour for necessary scaffolding and safety arrangement for guniting work, complete all as specified and directed. (Note :- The finish of the surfaces to be matched with the existing surface. WPC shall be measured & paid separately as supply only).

M&L mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire annealed, not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire annealed, not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All as per item No.121 above, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

S & F in repair gun metal globe or gate valve 25mm dia,ISI marked with iron wheel head, screwed both ends including all necessary accessories complete all as specified and directed

S & F in repair gun metal globe or gate valve 15mm dia,ISI marked with iron wheel head, screwed both ends including all necessary accessories complete all as specified and directed

Dismantling water tank exc 250 & n.exc 500 ltr capacity and removing to store complete all as specified and as directed

Dismantling water tank exc 500 & n.exc 1000 ltr capacity and removing to store complete all as specified and as directed

S&F White loft polyethylene water storage tanks, triple layered (ISI marked) of 1000 ltrs capacity (rectangular with closed top) hoisted and fixed in position all as specified in SSR Part-I, including provision of necessary fittings for connection the overflow, drain out, inlet and outlet pipes, complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks, double layered(ISI marked) of 500 ltrs capacity(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I, including provision of necessary fittings for connection the overflow, drain out, inlet and outlet pipes, complete all as specified and as directed.

S&F 25mm brass ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms) complete all as specified and as directed.

Demolition of tiles /cement concrete (unreinforced) from existing roof/terrace etc and also removing/taking down of existing water proofing treatment of any thickness in any position including cleaning the surfaces of roof etc with wire brush complete and removing the retrieved debris in low lying area, complete all as specified and as directed

M&L for special treatment for sunken portion of WCs/ Bath & toilet executed in following stages:- Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc including removing debris outside MD land etc . Stage 2:- Providing 10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per Manufacture's instructions. Complete. Stage 3:- Apply Dr Fixit Primeseal primer or Equivalent of STP Ltd (and allow to dry for 8 hours) all as per Manufacture's instructions. Stage 4:- Apply two coats of water proofing elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP (The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per Manufacturer's instructions. Stage 5:- Rendering 10mm thick in CM 1:3 mixed with Integral water proofing chemical Dr Fixit Pidicrete URP or plaster seal of STP Ltd all as per Manufacture's instructions. Stage 6. All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP all as per Manufacture's instruction. Stage 7:- Making holes in wall and fixing 600mm long 40mm dia medium grade GI spout for draining the surplus water if any . Stage 8:- Carry out ponding test for 48 hours to ensure water tightness of repaired sunken portion water tightness of repaired sunken portion and filling of sunken portion for cement concrete Type E2 1:5:10 using 40 mm graded aggregate as in lean concrete complete all as specified and directed. Note :- (a) Only plan area shall be measured and accorded for payment under this item. (b) Depth of sunken portion of WC's/Baths shall be upto 35cm, which is to be taken into account while quoting the rate against this item. (c) Rate quoted by Contractor shall be deemed to be included for all the horizontal and vertical treated surfaces of sunken portions of WC & Bath

M&L for PCC (1:2:4) type B-0, using 12.5mm graded stone aggregate as in levelling course over RCC roof surface to achieve required slope including making rounded or chamfered on edges mixed with WPC @3% by weight of cement, complete all as specified and directed. Note : WPC shall be measured and paid separately as supply only.

M & L for 4 mm thick APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160gm/Sqcm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm. (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimensional stability % change = Maximum 1%.

M&L for applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP roof membrane, complete all as specified and directed.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F steel rolling shutters thickness of laths 1.25mm, with out ball bearing as specified including top cover anchoring rod hasp and staple and one shop coat of primer erected in position as indicated, complete push pull or manual type complete all as specified and as directed.

S&F safety lever lock mils steel with 4 levers for rolling shutters complete all as specified and as directed.fied

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coat of aluminium paint over a coat of red oxide primer complete all as specified and directed.

M & L for Re-writing letters or figures (Block, Roman, Italic or Indian) n.exc 30cm height with synthetic enamel paint complete all as specified and directed.

M&L for Block boards, of 19 mm thickness grade 1 quality, exterior grade, decorative type with decorative face veneer on both face, for kitchen cabinet fixed with screws to timber frame work complete all as specified and as directed.

S&F Cubical of size 0.60x0.60x0.675 mtrs (minimum) made out from 19 mm thick plywood grade BWR including front facia PVC laminated, with wall supported at back, ply on three sides, resting below cooking platform. The cubical shall have three baskets (cutlery, cup saucer and thali) made out of stainless steel of grade 304 fixed with telescopic drawer channels and accessories. The internal surface shall be laminated with white colour complete all as specified and as directed.

S&F Cubical of size 0.60x0.60x0.675 mtrs (minimum) made out from 19 mm thick plywood grade BWR including front facia PVC laminated, with wall supported at back, ply on three sides, resting below cooking platform. The cubical shall have two baskets made out of stainless steel of grade 304 fixed with telescopic drawer channels and accessories. The internal surface shall be laminated with white colour complete all as specified and as directed.

S&F 19 mm thick plywood grade BWR as in cabinet complete all as specified and directed. complete all as specified and directed.

M&L 1.5 mm thick PVC laminates and fixed with approved Adhesive as per manufacturer instructions complete all as specified and directed.

M&L 0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer instructions complete all as specified and directed.

S&F Aluminium anodised profile handle no protruding type and shall match the surface of cubical complete all as specified and as directed.

S&F Kitchen cabinet hinges 2 hole full over lay make of Godrej complete all as specified and directed.

M&L for injecting chemical GLYPHOSPHATE (4% concentration) of 20 ml or till refusal by making cut/injection in the stem of plant of roots at 30mm and spraying with solution 25 ml GLYPHOSPHATE (4% concentration diluted with 1 ltr of water) and removing the plant /vegetation complete all as specified and as directed.

Chipping, removing carefully loose/damaged concrete including plastering (total thickness exceeding 40mm but not exceeding 60mm ) from surfaces of RCC members, in any location by low impact Hammer/Breaker without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris in low lying area complete all as specified and directed. Note : 1) Hard concrete shall not be removed by force

M&L for providing Polymer Bonding Agent of Fosroc (NITOBOND-SBR) OR equivalent brand of Dr. Fixit, as approved by the GE followed by flexible polymer based putty ( 1cement: 1.2 fine sand :20% polymer by weight of cement : water as required ) on cracks after cutting the cracks to a 'V' shaped groove upto 10 mm wide and 10 mm deep in structural RCC members, lintel,chajja finished with spatula etc. complete all as specified and directed.

M&L for building up the profile of structural members using polymer modified mortar from Polymer mortar HB of Dr Fixit or equivalent, while the bonding agent is still tacking upto 20mm thickness, including leveling, profiling and connected form works etc, complete all as specified and directed.

M&L for casting & repairing of excessively damaged distressed RCC members (exceeding 40mm in thickness) with prebatched, prepacked,single component ready to use micro concrete from FOSROC (Renderoc RG) or equivalent or Dr fixit as approved by GE, at any level/height and at any lead or lift as directed including prefabricated water tight formwork, centering, scaffolding, also including mixing, laying, levelling, finishing, curing etc as per manufacturers specifications and all other relevant works, complete all as specified and directed. Note : Reinforcement only shall be measured and paid separately)

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs/ blankets any thickness including cover fillets complete all as specified and directed.

Supply and Fix for Anodised aluminium snap grid framework, with size of grid 605 mm X 605 mm, for false ceiling, fixed with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm,4mm thick decorative type non asbestos fibre cement building boards fixed or laid /inserted to aluminium frame work as in ceiling complete all as specified and directed. Note:- The size of aluminium main and croos tee shall be 40mm x25mm x2mm and size of angle shall be 25mm x 25mm x 2mm)

M&L for preparation of new decorated surfaces of wall and applying two coats of antifungal exterior paint (of shade/colour as directed by GE) over one coat of primer all as per manufacturer instruction including necessary scaffoldings etc. complete all as specified and directed.

M&L for complete removal of existing treatment of wall by booming down or steel wire brushing scrapping down to remove smoke soot moulds moss and efflorescence salts and treating oil and greasy spots etc including washing down water etc. and applying two coats of antifungal exterior paint (of shade/colour as directed by GE) over one coat of primer all as per manufacturer instruction including necessary scaffoldings etc. complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and apply three coat of white wash complete all as specified and directed.

S&F 4mm thick figured glass/pin headed type ordinary quality with oil putty in squares n exc 0.5 Sqm in each pane fixed in steel ventilator, complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate, 75mm thick in plinth protection, footpath laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Supply only applying two coats of polymer modified cementious water proof coating as per manufactures instruction to bottom and vertical sides up to finished floor level +100mm height . The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion complete all as specified and directed.

M & L for Hydraulically machine pressed cement concrete tiles of size 300x300X20mm thick (with grey cement and no pigment), set in neat cement slurry laid over terrace and roofs etc including provision of 15mm thick cement screed bedding layer in CM 1:4 mixed with integral water proofing compound, tiles joints shall be grouted and immediately after grouting, the joints shall be pointed flush in CM 1:3 (in separate process) mixed with integral water proofing compound etc, complete all as specified and directed. (Note : Integral water proofing compound will be measured and paid separately as supply only).

M&L for sunken floor treatment by roughening of sides and bottom of sunken floor by picking, sweeping clean and washing down with water to remove dust etc. and 6mm thick rendering in CM(1:4) on concrete surface (bottom sides of sunken floor) finished fair and even mixed with liquid water proofing compound complete all as specified and directed..

M&L for non skid coloured ceramic tiles of 8 to 10mm thick (square/rectangular) area Exceeding 0.18sqm but not exceeding 0.38 sqm as in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer of CM 1:6 for fixing of tile in floor complete all as specified and as directed.

M&L for non skid coloured ceramic tiles of 7 to 8 mm thick (square/rectangular) area Exceeding 0.18sqm but not exceeding 0.38 sqm as in skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles including 10 mm thick screed bed or bedding layer of CM 1:3 for fixing of tile in skirting complete all as specified and as directed.

M&L for complete removal of old decorated surfaces of walls and applying two coats of cement base paint over a coat of primer on wall complete as specified and directed.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or inducting butt welded tubes, base plates conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed

M & L for reinforcement with 8mm dia TMT bars cut to length bent to shape required incl cranking bending spirally for hooping for columns hooking ends and binding with MS wire (annealed) not less than 0.90mm dia complete all as specified and as directed

M&L for RCC 1:2:4 type BI (using 20 mm graded stone aggregate) nominal mix as in fins, facias,chajja,lintel etc complete all as specified and as directed.

M&L for use and waste formwork to fins, louvers, fascia for fair finished surfaces of concrete, flat complete all as specified and as directed

S&F steel windows with side hung shutters including box type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded including one shop coat of Zinc Chrome primer complete all as specified.

All as per item No. 173.00 here-in-above hereinbefore but without glazing bars for gauzed shutter including one shop coat of Zinc Chrome primer complete all as specified and directed.

S&F for aluminum anodized barrel tower bolts of extruded section, 200mm long, ISI marked, complete all as specified and as directed

S&F MS butt hinges medium weight cold rolled of size 100mm complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with tinned tacks or galvanised wire staple complete all as specified and as directed

S&F 150mm long Aluminium handle cast type anodised complete all as specified and as directed

S&F sheet glass in repairs ordinary quality 3mm thick and glazing with oil putty and securing pins not exceeding 0.50sqm each pane complete all as specified and as directed

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15 deep in soft/loose soil and getting out complete all as specified and as directed

Hardcore of gauge not exc. 63mm, deposited, spread and levelling in layers not exc. 15 cm thick, watered and rammed to true surface with broken stone or boulder complete all as specified and as directed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed

Returning filling in including spreading leveling watering and well ramming in layers n exc 25 cmin soft/loose soil complete all as specified and as directed

Excavation in trenches n.exc. 1.5 m wide and n, exc 10 sqm on plan and not exc 1.5 deep and getting out in hard /dense soil complete all as specified and as directed

M & L PCC 1:4:8 type D2 using 40 mm graded aggregate as in foundation and mass concrete complete all as specified and as directed

M&L for 150 mm nominal dia DWCPE pipe (SN-8) pipes ISI marked laid in trenches and joined complete all as specified and as directed

M&L for PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in bed for drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 200 mm bore pipe complete as specified and as directed.

S&F in repairs CP brass towel rail 60cm long including fitting complete all as specified and directed. Cat Part No.AEC-1111 of ESSCO or equivalent complete all as specified and as directed

S&F in repairs CP brass overhead shower 80mm dia round shape Cat No.EOS-541N of ESSCO or equivalent with and and including CP brass shower arm 240mm long with wall flange Cat No.ALE 536A of ESSCO or equivalent complete all specified and directed.

S&F in repairs bib tap fancy type chromium plated cast copper alloy with capstan head wall flange screwed down screwed for iron pipe 15 mm bore. Cat No. DLX-511 of ESSCO or equivalent complete all as specified and as directed

S&F in repairs Concealed 15 mm Angle stop cock cast (male or female thread) copper alloy chromium plated fancy type with capstan head, wall flange screwed down screwed for iron pipe and fixed in repairs Cat No. DLX-511 of ESSCO or equivalent complete all as specified and as directed

S&F in repairs 15 mm Pillar tap cast copper alloy with capstan head chromium plated fancy type screwed down high pressure with or without letter hot or cold with long screwed shank and flynuts screwed for iron pipe. Cat No. DLX-507 of ESSCO or equivalent complete all as specified and as directed

S&F in repairs 15 mm stop valve (male or female thread) cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe and fixed in repairs complete all as specified and as directed

S&F in repairs of 15mm bore CP Toilet Hand Pressed Nozzle (Heath faucet) with 1.5 mtr long tube with CP wall bracket including taking down the old one complete all as specified and as directed.

Cutting chases in brick walls girth exc 10 cm but n exc 20 cm , pinning in making good to facings where required and pointing in cement mortar 1:3 for canceled water tubing etc and making good complete all as specified and as directed

S&F PVC waste pipe suitable for 32 mm dia waste coupling for wash hand basin complete all as specified and directed.

S&F stainless steel grating 100mm dia over floor trap complete all as specified and as directed

S&Fsheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12mm wide with CP brass bracket guard railing 60cm long complete all as specified and as directed

S&F in repairs 15 mm bore medium grade galvanized concealed steel water tubing with all fittings and fixed to wall/ceiling or laid in floor complete all as specified as in short lengths complete all as specified and as directed

M&L for cutting holes exc 150 sqcm but n exc 400sqcm into through brick wall built in mud mortar and making good CM 1:3 0r cement concrete 1:2:4 type B1 as required complete all as specified and as directed

S&F PVC (SWR) bends any radius suitable for 110mm bore pipe provided with access door complete all as specified and as directed

S&F PVC (SWR) bends any radius suitable for 75mm bore pipe provided with access door complete all as specified and directed.

S&F PVC (SWR) 110mm Junction (Single T) equal or un equal provided with access door complete all as specified and directed.

M&L PVC (SWR) gully trap 125/110mm setting and jointed with solvent cement complete all as specified and directed.

S&F PVC (SWR) 75mm bore junction (Single T) equal or un equal provided with access door complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete etc complete all as specified and as directed

M&L for RCC 1:2:4 type B-1(using 20 mm graded crushed stone aggregate) nominal mix as in columns, finished fair and even complete all as specified and as directed

M&L for RCC 1:2:4 type B-1(using 20 mm graded crushed stone aggregate) nominal mix as in foundations including raft footing, foundation beams, plinth beams, beams for columns etc complete all as specified and as directed

M&L for RCC 1:2:4 type B-1(using 20 mm graded crushed stone aggregate) nominal mix as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and as directed

Use and waste Formwork to sides of concrete foundations, footings bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work vertical or to batter, rough finished surfaces complete all as specified and as directed

Use and waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work n exc 200mm thick rough finished surfaces complete all as specified and as directed

M&L sand filling under floors or in foundation including watering and consolidation complete all as specified and directed (consolidated thickness shall be measured)

M&L for 75 mm thick PCC 1:4:8 Type D-2 (using 40mm graded mechanically crushed stone aggregate) as in sub base of flooring complete all as specified and as directed

M&L for 50 mm thick, PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in floor, finished even and rough with using extra cement complete all as specified and as directed

S&F rolled mild steel sections any type including hollow section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates (FE-290 Gde E-165) complete all as specified and as directed

M&L for PCC 1:3:6 type C1 (20mm grade agg) as in back filling of pressed steel frame complete all as per specification and directed by Engr in Charge.

S&F for steel windows for with side hung shutters including projecting type hinges with steel handles and still peg stay, complete with glazing bars, dovetailed welded complete all as specified and directed

S&F for steel windows for with side hung shutters including projecting type hinges with steel handles and still peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed

M & L for applying two coats of oil bound distemper with roller over one coat of primer, after preparation of new surfaces of walls etc, complete all as specified and directed.

Taking down carefully old unserviceable copper/aluminium point wiring (light,Exchaust fan, socket or power) complete incl fittings such as switches, ceiling roses, pendents, regulators,bells,sockets,tube light fittings etc, and making good disturbed surface of walls & floors etc complete all as specified and as directed.

Taking down old unserviceable Main Switch, DB's consisting of MCBs wooden/GI/MS sheet board etc complete all as specified and as directed

Taking down carefully unserviceable sub main wiring of any size/core/type including making good the disturbed surfaces complete all as specified and as directed

M&L for concealed point wiring with two single core PVC insulated, unsheathed, multistranded copper conductor FRLS of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.50 sqmm green in colour as earth lead in and including PVC rigid conduit (medium grade) with all fittings & accessories for mounting modular switch, sockets, fan regulators etc for one light / fan point / call bell point complete all as specified and as directed NOTE : Cost of making good the disturbed surfaces (if any) matching with the existing surface is deemed to be included in the unit quoted rates. Modular fitting will be paid & measured under relevant items separately.

All as per Item Sl No 225.00 here-in-above but with two single core PVC insulated, unsheathed, multistranded copper conductor of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.5 sqmm green in colour as earth lead for 5/6 A switch-socket point on independent board complete all as specified and as directed

All as per Item Sl No 225.00 here-in-above but with two single core PVC insulated, unsheathed, multistranded copper conductor of size 2.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 2.5 sqmm green in colour as earth lead for 15/16 A switch-socket point on independent board complete all as specified and as directed

All as per Item Sl No 225.00 here-in-above but with two single core PVC insulated, unsheathed, multistranded copper conductor of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.5 sqmm green in colour as earth lead for 5/6 A socket point with switch on same board complete all as specified and as directed

All as per item Sl No 225.00 here-in-above but for one light point controlled by two 2 way switches for modular fitting complete all as specified and as directed

S&F modular switch one way 6 Amps 230 volts, 1 module complete all as specified and as directed by the Engineer in charge

S&F modular bell push switch one way 6 Amps 230 volts, 1 module complete all as specified and as directed by the Engineer in charge

S&F modular switch two way 6 Amps 230 volts, 1 module complete all as specified and as directed by the Engineer in charge

S&F modular switch one way with indicator 16 Amps 230 volts, 1 module complete all as specified and as directed by the Engineer in charge

S&F modular socket 2 in 1, 2/3 pin, 6 Amp complete all as specified and as directed by the Engineer in charge

S&F modular socket 3 pin, 6-16 Amp combined shuttered complete all as specified and as directed by the Engineer in charge

S&F modular white cover plate with frame 1 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge.

S&F modular white cover plate with frame 2 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge.

S&F modular white cover plate with frame 3 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge.

S&F modular white cover plate with frame 4 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge.

S&F modular white cover plate with frame 6 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge.

S&F modular white cover plate with frame 8 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge.

S&F modular white cover plate with frame 12 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge.

S&F modular metal flush box 1/2 module complete all as specified and as directed

S&F modular metal flush box 3 module complete all as specified and as directed

S&F modular metal flush box 4 module complete all as specified and as directed

S&F modular metal flush box 6/8 module complete all as specified and as directed

S&F modular metal flush box 12 module complete all as specified and as directed

S&F ceiling rose ,surface bakelite 65mm x 50mm size with three terminals complete all as specified and as directed

S & F Bell Ding-Dong AC 230 V Single Pole complete all as specified and as directed

Taking down existing u/s FTL light fitting and S&F in repair decorative box type fitting with LED retrofit tube 20 watt with Al extruded batten luminaries for 230 volt AC,including LED tube 20 Watt complete all as specified and as directed by EIC

Taking down existing u/s FTL light fitting and S&F in repair decorative box type fitting with LED retrofit tube 9 watt 2 feet with Al extruded batten luminaries for 230 volt AC,including LED tube 10 Watt complete all as specified and as directed by EIC

Taking down ceiling fans of any size, sealing cable end, dismantling blades and removing fan and blades to store for refixing or complete all as specified and as directed

S&F modular electronic step regulator (speed regulation in 5 steps) 1 module suitable for ceiling fan 1200 sweep/1400 mm, 120 Watt complete all as specified and as directed

S&F in repair energy efficient, star rated ceiling fan 230V 1200 mm sweep with all accessories and connecting up with the ceiling rose with required flexible wire of suitable size with ceiling fan complete all as specified and as directed.

S&F exhaust fan AC with louvers, single phase, 230/240 V, of size 300 mm seep steel/aluminium metal body incl making holes on wall & making good the disturbed surfaces with all connecting arrangements complete all as specified and as directed.

M&L LED street light of capacity 30 watt in Aluminium PDC housing, toughened glass cover with IP66 protection complete all accessories with connections PVC copper wire not exc 5 mtr and complete all as specified and as directed

S&F ventilation fan with louvers, single phase, 230/240 V, of size 200 mm seep polycarbonate body, incl making holes on wall & making good the disturbed surfaces with all connecting arrangements complete.

Supply & Fixing TP&N DB 4 way with sheet metal enclosure 415 volts, double door 160 Amp rated bus bar for MCB incl cutting chases exc 10 cm but not exc 20 cm girth for DB and making good disturbed surface area complete all as specified and as directed.

Supply & Fixing DB with sheet metal enclosure 240 volts, 12 way with rated bus bar single pole & neutral double door for MCB, incl cutting chases for DB of reqd size and making good disturbed surface area complete all as specified and as directed.

Supply & Fixing DB with sheet metal enclosure 240 volts, 8 way with rated bus bar single pole & neutral double door for MCB, incl cutting chases for DB of reqd size and making good disturbed surface area complete all as specified and as directed.

S&F MCB TPN 63Amp 415 volt breaking capacity 16KA complete all as specified and as directed

Supply & Fixing MCB double pole (DP) 240 volts of capacity 6-40 Amp ,C curve, complete all as specified and as directed.

S&F MCB, SP, 10KA, 415V, "C" curve, 06-32 A, ISI Marked complete all as specified and as directed

Material and labour for concealed sub main wiring surface type with two nos single core PVC insulated unsheathed multi strand copper conductor FRLS cable of size 10 sqmm and one no single core PVC insulated unsheathed multi strand copper conductor FRLS cable of size 10 sqmm as in continuous earth wire drawn into and including surface rigid non-metallic ISI marked PVC conduit medium grade with all fittings and fixings accessories complete all as specified and as directed.

Material and labour for concealed sub main wiring surface type with two nos single core PVC insulated unsheathed multi strand copper conductor FRLS cable of size 6 sqmm and one no single core PVC insulated unsheathed multi strand copper conductor FRLS cable of size 6 sqmm as in continuous earth wire drawn into and including surface rigid non-metallic ISI marked PVC conduit medium grade with all fittings and fixings accessories complete all as specified and as directed.

M & L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground (in vertical position ) earth pit not less than 2.25 mtrs below normal ground level with the top edge of the earth plate not less than 1.5 mtr (B.G.L.) & connected to galvanised iron wire 4 mm dia by means of bolts,nuts,checknuts & washer of galvanised iron including PCC (1:2:4) type B1 precast RCC cover slab with suitable handle made pf 6 mm round bar, including necessary excavation & earth work in any type of soil , 20 mm dia med grade galavinised steel tube for watering with one end fixed with cast iron funnel & wire mesh, 15 mm bore light grade galvanised steel tubing up to 7.5 mtr length for drawing earth lead GI strip protection & common salt , charcoal in alternate layers etc. complete all as shown in EP no 3 of SSR Part 1 & testing on completion incl taking down old unsv earthing complete.

M&L for concealed point wiring with two single core PVC insulated, unsheathed, multistranded copper conductor FRLS of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.50 sqmm green in colour as earth lead in and including PVC rigid conduit (medium grade) with all fittings & accessories including provn of MS sunk terminal box of appropriate size suitable for switch fixed flush to wall for mounting switch, sockets, fan regulators etc with 3mm thick phylum sheet top cover with screws & cup washers for one light / fan point / call bell complete all as specified and as directed NOTE : Cost of making good the disturbed surfaces (if any) matching with the existing surface is deemed to be included in the unit quoted rates.

All as per Item Sl No 266.00 here-in-above but with two single core PVC insulated, unsheathed, multistranded copper conductor of size 4.0 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 4.0 sqmm green in colour as earth lead for 15/16 A switch-socket point on independent board complete all as specified and as directed

M & L for Switch Socket combination 3 Pin, 5 Amp flush type universal, 240 volts, complete all as specified and as directed

M & L for Socket outlet 3 Pin, 5 Amp flush type universal, 240 volts, complete all as specified and as directed

M & L for Switch Socket Combination 5 in 1, 3 pin, 5 and 15 Amp flush type universal, 240 volts, complete all as specified and as directed

S&F piano switch single pole 5 Amp 230 Volt complete all as specified and as directed

S&F including taking down existing, new generation energy saving & environmental friendly long life versatile pressure die-cast aluminium building security light with high power LED as light source lamp type 25W with SPD, IP 66 protection with toughened glass incl fixing pipe/saddle complete all as specified and as directed.

S&F MCB, SP, 10KA, 230V, "C" curve, 06-32 A, ISI Marked complete all as specified and as directed

S&F MCB, DP, 10KA, 415V, "C" curve, 06-32 A, ISI Marked complete all as specified and as directed

S&F new generation energy saving & environmental friendly long life versatile pressure die-cast aluminium building security light with high power LED as light source lamp type 25W with SPD, IP 66 protection with toughened glass incl fixing pipe/saddle complete all as specified and as directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation etc and getting out soft or loose soil complete all as specified and as directed.

Returning filling in including spreading leveling watering and well ramming in layers n exc 25 cm in soft/loose soil complete all as specified and as directed.

Removing excavated material n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified and as directed.

Supply and lay in trenches or passing through pipe LT UG XLPE insulated ,armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 10sq mm 2 core including making necessary connections complete all as specified and as directed

Supply & laying in trenches clear sand for cushioning under cable 8 cm below and 15 cm above complete in level complete all as specified and as directed.

Supply and laying burnt clay sub class B brick as cable protection complete all as specified and as directed

S&F GI pipe 40mm bore light grade ISI marked including fittings fixed for cable protection alongwith wall complete all as specified and as directed.

M/S.TIRUPATI CONSTRUCTION

CHAKRABORTY AND SONS

S.N. GHOSH AND CO.

M/S JYOTI SHARMA AND SONS

M/S R. K. INDUSTRIES

M/S JANATA CONSTRUCTION

M/s Singh enterprises