Construction of Tourist and Amaranth Yatra Interpretation Centre at Pahalgam.Balance Part

Providing and laying in position cement concrete of specified grade including curing but excl the cost of centring and shuttering. All work with 1:2:4 aggregate 20 mm incl all carriage complete job

Centering and shuttering including strutting, propping and removal of form work in foundation

steel work welded in built up sections / framed work , including cutting , hoisting , fixing in position and applying a priming coat of approved strel primer using structural ate ne os required

Providing & fixing Precoated galvalume profile sheets 0.50 mm TCT having a crest height of 28-32mm at 195mm pitch and effective width of 975-1000mm and length to suit site requirement to the purlins using self drilling and self tapping fasteners of reputed make with purlin sheet using self drilling and self tapping fastners & Fixing flashings, valleys and ridges of colour coated galvalume plain sheet using self drilling and self tapping fasteners of reputed makel complete and as directed. The contractor shall give a minimum of 10 years guarantee for sheets against deterioration, disintegrations loss of luster, variation in colour, etc. and leakages across laps, fasteners etc. All types of steel sheets shall be load tested to satisfy 1.10 times the design wind load and coating thickness to the satisfaction of the Engineer-in-Charge. Fasterners shall also be load tested. The Contractor is to submit design and shop drawings for approval on the sheet profile, design and fabrication details before installation (including cost of all material,leads, lifts and carriages ete upto site of work complete) (white Colur)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete SIZE 600 mm x 60 mm same as plinth area

Providing and fixing false ceiling with 16 mm thick plain/ semi perforated or with design ceiling tiles of BWP type phenol formaldehyde synthetic resin bonded pressed particle board conforming to 15:3087, finished with a coat of aluminum primer on both sides & edges, including two coats of synthetic enamel paint of approved quality on exposed face, fixed to a grid made out of anodized aluminum (with 15 micron anodic coating) T sections 35 x15x1.5 mm size main runners, cross runners 23.5x19x1.5 mm 13 fixed to main runners placed 600 mm centre to centre both ways so as to form a grid of 600 mm square. The frame work shall be suspended from ceiling by level adjusting hangers of 6 num dia M.S rod fixed to roof slab by means of ceiling cleats and dash fastener.

Providing and fixing aluminium work for doors, window ventilators and partitions with extruded built up standard tubular sections/ appropriate Z. sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with rawl plugs and screws or with fixing clips, or with cxpansion hold fastmers including necessary filing up of gaps at junction at top bottom and sides with required PVC/neoprene felt etc. aluminium sections shall be smooth rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminiunt snap bending for glazing/panelling. CP brass/stainless steel screws, all complete as per architectural drawings and the directions of 14 Engineer in Charge Polyester powder coated aluminium (mininuun thickness of polyester powder coated 50 microns) 20002 For Frames

Providing and fixing aluminiuin work for doors, window ventilators and partitions with extruded built up standard tubular sections/ appropriate Z. sections and other sections of approved make conforming to 15-733 and 15: 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junction at top bottom and sides with required PVC/neoprene fell etc. aluminium sections shall be smooth rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ panelling. C.P brass/stainless steel screws, all complete as per architectural drawings and the directional of Is Engineer in Charge Polyester powder coated aluminium (minimum thickness of polyester powder coated 50 microns) 19592 For Shutters Incl Fixtures

Providing and fixing of 12mm thick Decorative type Particle Board

Providing and fixing of 5mm thick glass panes fitted with EPDM rubber in aluminuim door windows