ADDITION ALTERNATION OF OTM ACCN AT EME CENTRE, SECUNDERABAD

Amount

B/R ITEMS

Dismantling of stone slabs in roofs, suspended floors, etc., any thickness jointed in any mortar etc and removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

Dismantling mangalore pattern roofing tiles single layer including ridge tiles laid, bedded in cement mortar etc complete all as specified and as directed.

Dismantling asbestos cement (corrugated ) sheet in roof covering/ fibre sheets etc complete all as specified and directed. Note: 30% quantiy of serviceable AC sheet to be deposited at AGE B/R No.1 Store including loading and unloading with transportation and the rate quoted is deemed to be inclusive of the same.

Dismantling of CGI/PGI sheet roofing any gauge and any thickness including ridge, valley gutter etc complete all as specified and as directed.

Supply and fix pre-painted galvalume aluminium zinc coating galvanised based corrugated steel sheet of 0.50 mm thick of approved colour having tensile strength of 550 Mpa as roof covering/cladding to wall fixed with self tapping (SD) screws complete all as specified and as directed

Supply and fix pre-painted galvalume aluminium zinc coating galvanised based profile/plain steel sheet of 0.50 mm thick of approved colour having tensile strength of 550 Mpa as ridge, gutters fixed with self tapping (SD) screws complete all as specified and as directed

Dismantling battens for tiles any size exceeding 15cm in spacing complete as directed.

Dismantling timber Scantling framed work in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified and as directed.

Dismantling timber Scantling framed work 40 sqcm and over in section, in any position complete all as specified and as directed.complete all as specified and as directed. Note: 30% quantity of serviceable timber scantling to be deposited at AGE B/R No.1 Store including loading and unloading with transportation and the rate quoted is deemed to be inclusive of the same.

Fixing only 2nd class H/W clean sawn timber scantling as in purlins, trusses etc. framed work complete all as specified and as directed. Note : Serviceable timber scantiling obtained vide item No 9 shall be reused

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and and as directed

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness including cover fillets etc complete all as specified and directed..

Supply and fix Grid suspended false ceiling grid system of size 600 x 600mm with main runner 39x29.7x0.60mm cross tee 29x24.7x0.60mm and wall angle 22.2x22.2x0.50mm ceiling suspended with 2 to 2.5 mm dia GI wire hanger fixed to purlin / truss etc complete (Main runner, cross tee, wall angle of MS galvanised with PP CGS) over the grid providing 4mm thick HPSC pre primed self designer texture non asbestos fibre cement building board fixed to frames complete all as specified and as directed

Material and Labour for fixing Gypsum Board 12mm thick in ceiling fixed with screw and Gypsum board surfaces of ceiling and applying two coats of distemper oil emulsion over 3 mm thick wall care putty and a coat of primer using chalk whitening as per manufacturers instruction and all as directed.

Supply and fix joist channel, angle or tee sections, fixed independently without connecting plates, etc., ( cut to ordinary lenghts i.e within 20mm of the length indicated of Fe 410-W ( Gde-E-250) quality A and including necessary precautionary measures as in supports etc complete all as specified and directed.

Supply and fix Roof trusses (framed) and connecting plates, etc., ( cut to ordinary lenghts i.e within 20mm of the length indicated of Fe 410-W , Gde-E-250) quality A Note: The ISMB's have to be inserted in wall by replacing damaged existing rafters as in old madras terrace roof including taking necessary precautionary measures as in supports etc., complete all as directed.

Supply and fix Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment etc.Roof trusses (framed) and connecting plates, etc., complete including necessary precautionary measures as in supports etc., all as directed.

Supply and fix wind ties for roof including securing bolts including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 etc complete all as specified and directed.

Supply and fix Mild steel bolts made.with hexagonal or forming holes, without any attachment dia of neck exc 20mm not exc 25mm etc complete all as specified and directed.

Material and labour for plain cement concrete 1:2:4, type B1 using 20 mm graded stone aggregate as in bed block, coping, roof kerbs, bands etc including necessary form work complete all as specified and as directed

Material and Labour for RCC 1:2:4, type B1, using 20mm graded stone aggregate as in Lintel band etc complete all as specified and directed.

Material and Labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams etc as in rough finished flat surfaces of concrete etc complete all as specified and directed.

Material and Labour for mild steel TMT bars 10mm dia and over including all cutting bending, binding, cranking placing & binding with MS wire (annealed) not less than 0.90mm dia etc complete all as specified and directed.

Material and Labour for mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups , spacers and binders etc., including all cutting bending, binding, cranking placing & binding with MS wire (annealed) not less than 0.90mm dia etc complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar with all quoins, arches, pillars, etc but excluding ashlar facings, dressed stone work and precast concrete articles including disposal of the rubbish out off the premises etc complete all as specified and directed.

Material and labour for brick work with fly ash bricks old size, straight or curved on plan exceeding 6.0 metre mean radius built in cement mortar 1:4 complete all as specified and as directed

Material and labour for walling of squared rubble masonry regular coursed, Secunderabad and Bangalore types, well bonded, bedded and solidly hearted, built in cement mortar 1:6 etc complete all as specified and directed.

Material and labour for walling of squared rubble masonry regular coursed, Secunderabad and Bangalore types, well bonded, bedded and solidly hearted, built in cement mortar 1:6 etc but except stones. complete all as specified and directed. Note- Serviceable stones obtained vide item No 25 shall be reused after removing mortar and cleaning with water complete all as specifed and directed. .

Material and labour for brick work with fly ash bricks old size, straight or curved on plan exceeding 6.0 metre mean radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed

Taking down cement plaster of any description and thickness on brick walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed

Material and labour for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 without using extra cement complete all as specified and as directed

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 without using extra cement complete all as specified and as directed

Material and Labour for rendering 10mm thick in cement mortar 1:6 and 5 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces in two coats (10 + 5 mm), top coat mixed with integral water proofing liquid ISI Marked as per manufacturers instructions and finishing the surface even and fair complete all as specified and directed Note - WPC shall be measured and paid separately

Supply only water proofing liquid of ISI marked complete all as specified and as directed.

Material and Labour for preparing newly plasterd wall surfaces of walls and applying two coats of distemper oil emulsion over 3 mm thick wall care putty and a coat of primer etc complete all as specified and as directed.

Material and Labour for preparing newly plastered wall surfaces and applying three coats of white wash complete all as specified and as directed.

Material and Labour for preparing the old plastered or unplastered decorated surfaces of walls and applying two coat of white wash all as specified and as directed.

Material and Labour for complete removal of existing treatment on wall surfaces and applying two coats of oil bound distemper over a coat of primer over a coat of 3mm thick birla wall care putty etc all as specified and as directed.

Material and Labour for preparing old decorative surfaces of walls, by washing, rubbing down, stopping and applying two coats of cement base paint of approved colour all as apecified and as directed

Material and Labour for preparation of new surfaces of steel, of any description, not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Material and Labour preparation of old painted surfaces of wood and applying one coat of synthetic enamel paint on wood or wood based material over 10 cm width or girth etc complete all as specified and directed.

Material and Labour preparation of old painted surfaces of steel and applying two coats of synthetic enamel paint on steel surfaces over 10 cm width or girth etc complete all as specified and directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for and removal of rubbish/ demolished materials outside of MD land complete all as specified and directed.

Material and Labour for 75 mm thick plain cement concrete 1:4:8 mix,type D2 (using 40 mm graded stone aggregate) as in subbase to floor complete all as specified and as directed.

Material and Labour for PCC 25mm thick, 1 : 2 : 4 type Bo(12.5 mm graded stone aggregate) as in sub-base to floors as a levelling layer etc., where ever as required all as specified and directed.

Material and Labour for designer rubber moulded chequerred cement concrete tiles with mixture of grey and white cement in equal porportions with pigments of size 200x 200xx25mm ,300 x 300 x 22mm or 250 x 250 x 22mm thick and set and pointed in neat cement slurry in floors over a screed bed or bedding layier in CM 1:6, 15mm thick for laying floor finishes etc complete all as specified and as directed.

Material and Labour 75 mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) in plinth protection laid in alternative bays finished even and smooth without using extra cement including making 10 mm wide grooves to full depth at 3 m interval and at every change of direction and filling the grooves with mixture of bitumen and sand mixed in the ratio of 1:3 by weight and top 10 mm depth sealed with sealing compound grade ‘A’ complete all as complete all as specified and as directed

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and as directed.

Material and labour for glazed ceramic coloured wall tiles of approved colour of size 350x 250x 7/ 450x300x7 mm thick on vertical surfaces as in dado/wall set and jointed in neat cement slurry and pointed with white or coloured cement to match over including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and as directed

Material and labour for non-skid ceramic coloured tiles of size exceeding 0.11 sqm but not exceeding 0.18 sqm of 7 to 8 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in white/coloured cement to match laid over including 15 mm thick screed bed in cement mortar 1:6 and also dismantling of existing tile complete all as specified and as directed

Material and labour for Non skid coloured ceramic tiles of size exceeding .0.06 square metre but not exceeding 0.11 square metre of 7 to 8mm thick set and jointed in neat cement slurry and pointed in coloured cement to match, laid over including cement screed bed of cement mortar 1:6 of 15 mm thick complete all as specified and as directed.

Material and Labour 20-25 mm thick machine cut Polished kota stone as in flooring , treads of staircase laying down and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over bedding layer of 15mm thick in CM 1:6 complete all as specified and directed.

Material and Labour 20-25 mm thick machine cut Polished kota stone as in skirting / riser of staircase, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over a backing coat of 10mm thick in CM 1:4 complete all as specified and as directed.

Material and Labour for vitrified ceramic tilies 10 mm thick (square/rectangle) , light shade, area of each tiles n.exc 0.36 sqm each in floors and jointed in neat cement slurry and pointed in white or coloured cement to match over including providing screed bed or bedding layer of cement mortar 1:6, 15mm thick complete all as specified and as directed

Material and Labourfor vitrified ceramic tiles 10 mm thick (square/rectangle) light shade, area of each tiles n.exc 0.36 sqm each in skirting / dados and jointed in neat cement slurry and pointed in white or coloured cement to match over including rendering 10mm thick on brick/concrete surface in CM 1:4 to receive tiles in skirting/dados complete all as specified and as directed

Taking down chowkats or frames with shutters (without taking off shutters from frames) of size not exceeding 1.5 Sqm each complete all as specified and as directed

Taking down chowkhats or frames with shutters (without taking off shutters from frames) of size exceeding 1.5 sqm and not exc 4 sqm each complete all as specified and as directed

Supply and fix Solid PVC door frame of size 50 x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube, all as specified and shown in Section 8 of MES Schedule Part-II 2020 complete all as specified and as directed

Supply and fix Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawings given in Section 8 of MES Schedule Part-II 2020 as applicable complete all as specified and as directed

Supply and fix steel windows (fly proof and glazed shutter) made with galvanised steel colour coated/ powder coated ( Base steel as per IS 513 'D', galvanised as per IS 277 with zinc of 120gm/sqm) with total coating thickness of 0.60mm. ( outside for glazing and inside gauged shutter) Sections for frame should be of 72mmx55mm, section for mullion should be 72mm x 50mm section for shutter frame should be 47mmx 20mm,and section for fixing glass bead should be 12mm x 12mm and section for fly mesh shutter frame should be 40mm x 20mm mesh fixing should be of 18mm x 0.6mm. Stainless steel wire mesh of 0.45mm dia and ave width of aperture 1.4mm shall be used for fly proofing . 4mm thick plain sheet glass to be used for glazing of glazed shutters including 10mm powder coated square saftey grills, locking arrangement and all necessery accessories etc, completed all as specified and directed .

Supply and fix PVC solid ventilator frame size 55 X 47mm with wall thickness of 5mm made out of extruded 5mm PVC sheet, mitre cut at two corners and jointed with 2 Nos of 150mm long brackets of 15 x 15mm MS square tube the two vatted profiles are to be reinforced with 19 x 19mm MS squre tube the 50% of bottom portion is fixed with 4mm pin headed glass and balance 50% of top portion is fixed with 4mm thick pin headed glass lowers and cover with 0.36mm dia stainless steel wire mesh at top portion including necessary PVC beading with screws and 3 Nos 12mm dia MS guard, bars fixed in ventilator frame including two coats of synthetic enamel paint over a coat of red oxide primer to MS guard bars etc all as per specified and directed.

Supply and fix 125 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed.

Material and labour for plain cement concrete 1:3:6, type C1 (using 20 mm graded stone aggregate) as in coping, bed plates, filling back hollow portion of chowkats complete all as specified and as directed

Cutting holes in brick wall built in cement mortor for inserting hold fast and making good the disturbed portion in cement mortor 1:3 depth of embeded portion exc half brick & n.exc one brick all as directed.

Supply and fix 35 mm thick factory made second class hardwood, plain framed panelled shutters (any number of panel) with panels of timber flat on both sides(feather edged) or of veneered particle board medium density wood particle board with commercial veneering on both faces. complete all as directed and specified.

Supply and fix 30 mm 2nd Class hard wood factory made glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Part-I section 8 clause 8.24(a) etc completed all as specified and directed .

Supply and fix Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc all as specified and directed.

Supply and fix 150 mm extruded aluminium alloy hands, fabricated type, anodised complete all as specified and directed.

Supply and fix 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed .

Supply and fix butt hinges of 100mm size extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type C-21 complete all as specified and as directed

Supply and fix mild steel sliding bolt 300 mm long plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fix complete all as specified and as directed

Material and Labour for applying new wood surface two coats of synthetic enamel paint over a coat of pink primer on wood or wood based material over 10 cm width or girth including preparation of new wood surface

Supply and fixed in repairs 2nd class hard wood plain small fittings such as brackets of any type , latch and hinge blocks, shaped door and window stoppers and the like , including all necessary labours, articles not exc 200 cu cm each complete all as specified and as directed

Material and Labour for one coat of creosote oil painting to old tiles or slate battens, any size and spacing, prepared and treated all over (measured overall on one side only, spaces not deducted) etc complete all as specified and directed.

Supply and fixed in repair aluminium powder coated (fancy type) tubular curtain rod and bracket 20mm dia complete all as specified and as directed.

Dismantling water tanks exc. 500 and n. exc 1000 litres and removing to store etc complete all as specified and directed.

Supply and fix rotational moulded polyethyiene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity etc complete all as specified and directed.

Dismantling water tanks exc. 250 and n. exc 500 litres and removing to store etc complete all as specified and directed.

Supply and fix rotational moulded polyethyiene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity etc complete all as specified and directed.

Supply and fixed in repairs 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. .(Minimum weight 20mm-210 gms.) etc complete all as specified and directed.

Supply and fixed in repairs for 20mm gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed etc complete all as specified and directed.

Supply and fixed in repairs vitreous china wash down water closet squatting pan, Orissa pattern of size 580x440mm with integral foot rest , colour white with and including P trap, lime concrete bedding and making necessary connection to soil pipes and flushing cistern etc.,complete all as specified and as directed.

Supply and fixed in repairs chromium plated shower roses 125mm size with or without swivel joint including fixing to steel pipe or union etc.complete all as specified and directed.

Supply and fix in repairs Towel rail 600mm long of PTMT fixed with and including CP brass screws and wooden/plastic cleats. (Minimum weight 190 gms)

Taking up or down steel tubing 15mm bore and connections including cleaning for refixing or removal to store / taken on credit complete all as specified and as directed.

Supply and fix tubes, ‘medium grade’ galvanised, 15 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.

Refixing old steel tubing of 15 mm bore and connections in new or old position (walls, ceilings, floors etc.) etc complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm complete all as specified and directed.

Refixing old steel tubing of 20 mm bore and connections in new or old position (walls, ceilings, floors etc.) etc complete all as specified and directed.

Supply and fix for tubes, ‘medium grade’ galvanised, 20 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.

Supply and fix in repairs CP bib tap 15mm bore fancy type with crutch or butterfly handle, screwed for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fixed in repairs stop valve / angle cock fancy type cast copper alloy chromium plated with capstan head serewed down for 15 mm dia iron pipe.

Supply and fixPVC (SWR) Nahani /Floor trap, 75 mm dia of out let, plain with grating including jointing to waste pipe with solvent and cement concrete type B1 (1:2:4) & including removing old trap and fixing of stainless steel grating in ground shape etc complete all as specified and as directed.

Supply and fix in repairs PVC 10 ltrs capacity symphonic action type low level flushing cistern including flush pipe, cantilever brackets incluiding taking down existing cistern etc complete fixed in repairs .

Supply and fix PVC connections, 15mm size with PTMT nuts of length 450mm all as directed.

Supply and fix 110 mm bore UPVC Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches including taking down of old pipes.

Supply and fixing UPVC/PVC (SWR) junction single (single T ) equal or unequal 110mm dia with access doors complete all as directed.

Supply and fix110mm dia vent cowl UPVC/PVC (SWR) all as directed.

Supply and fix 110mm bore UPVC/PVC (SWR) plain bends, any radius all as directed.

Supply and fixin repairs Vitreous China wash basin, white, flat back, size 550x400mm excluding ditto but including brackets including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe etc complete all as specified and directed.

Supply and fixing pillar taps cast copper alloy fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm bore fixed in repairs etc complete all as specified and directed.

Supply and fix 4mm dia Plain mild steel wire, galvanised class 3, in mosquito net and fixing in straining bolts , hook and eyes fencing including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and tying wire, galvanised iron staples or steel pins, etc. as directed be measured

Excavation in post holes or similar holes n.exc 0.50 cum and getting out/returning, filling in and ramming removing surplus soil to a distance n.exc 50 m in soft/loose soil all as specified and directed.

Material and Labour PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation and mass concrete all as specified and directed.

Supply and fix steel structure/frame made of MS box/pipe sections ERW or induction butt weld tubes conforming to IS-1161-1979 grade st 240 as in columns,purlins and truss complete fitting as directed including one shop coat of red oxide primer and two coats of synthetic enamel paint complete all as directed.

E/M PORTIONS

Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and seperating the serviceable items like fan regulators and light fittings for re-use under respective items and removal of unserviceable material out of site for taking into credit and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified and directed.

Material and Labour for Point wiring with 1.5 Sq mm copper conductor single core FRLSH PVC insulated unsheathed 1100 Volts multistranded drawn through and including rigid PVC conduit concealed/ surface as per site requirment and conduit accessories of suitable dia medium grade and pressed steel terminal boxes of 2 mm thick MS of suitable size duly painted with red oxide metal primer including fixing/grouting sunken/ surface as per site requirement covered suitable for fixing switches / sockets/ regulators etc including running up of 1.5 Sq mm copper conductor FRLSH PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly all as specified and directed. :-

One light point/Bell point controlled by one, one way switch 5 amps, SP

One Ceiling Fan / exhaust fan point controlled by one, one way switch and regulator

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board .

One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

Description as per item No. 108 here in before but using 4.0 Sqmm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 Volts grade for 5 Pin 15 Amps switch socket combination point on independent board including running of 4.0 Sq mm copper conductor FRLSH PVC insulated cable as earth continuity conductor all as specified and directed.

Supply and fix switch piano single pole flush type 6 amps, 230 volts all as specified and directed.

Supply and fix switch socket combination flush type multipurpose 3 pin 6 amps 2 in 1 230 Volts all as specified and directed.

Supply and fix switch socket combination 2 in 1 multipurpose 5 pin 6/16 amps flush type complete all as specified and directed.

Supply and fix bell push piano type of 6 Amps SP, 230 volts AC complete all as specified and as directed.

Supply and fix bell ding dong type working on 230 volts single pole AC supply complete all as specified and as directed.

Supply and fix electronic ceiling fan regulator stepped type heavy duty suitable to work on 230 volts complete all as specified and directed.

Supply and fix lamp holder insulated body surface bakelite with back plate suitable for angle / batten fittings fixed with PVC round blocks all as specified and directed.

Supply and fix ceiling rose three terminal surface bakelite type AC 50 Hz 230 volts of size 65 x 50 mm complete all as specified and directed.

Supply and fix LED tube light fitting 20 Watts , 230 volts, box type, epoxy powder coaded with reflector cover channel, with electronic drive, bipin holders, connector block, internally pre wired etc with necessary mounting arrangements including all accessories with new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting all as specified and directed.

Supply and fix LED security Light fitting 1x35 Watt complete with Bracket made out GI pipe med grade 25mm of L Shape 1.5 Mtr long incl clamps and nuts botls etc , all as specified and directed.

Supply and fix sheet metal enclosure MCB DB SPN 8 way with 200 amps rated bus bar 240 volts double door with magnetic locking system complete all as specified and directed.

Supply and fix MCB SPN 240 volts suitable for fixing in MCB DB of capacity 40 / 63 amps complete all as specified and directed.

Supply and fix MCB SP 6 to 32 Amps 240 volts for fixing on MCB DB's all as specified and directed.

Material and labour for sub main wiring with two runs of single core FRLSH PVC multi stranded unsheathed copper conductor cable of size 4 square mm and drawing through PVC conduit of 20mm dia with accessories on surface in wall/roof along with one run of 4 square mm FRLSH PVC insulated unsheathed multi stranded 1100 volts grade with copper conductor cable as earth continuity conductor connected to earth and earth dolly, connecting to main board including removing the existing wiring and making good the disturbed wall surfaces to match with the surroundings complete all as specified and directed. Note: 3 runs of 4 Square mm cable and 1 run of PVC conduit with accessories shall be measured as 1 unit of running metre.

Material and labour for sub main wiring with two runs of single core FRLSH PVC multistranded stranded unsheathed copper conductor cable of size 6 square mm and drawing through PVC conduit of 20mm dia with accessories on surface in wall/roof along with one run of 6 square mm FRLSH PVC insulated unsheathed multi stranded 1100 volts grade with copper conductor cable as earth continuity conductor connected to earth and earth dolly, connecting to main board including removing the existing wiring and making good the disturbed wall surfaces to match with the surroundings complete all as specified and directed. Note: 3 runs of 6 Square mm cable and 1 run of PVC conduit with accessories shall be measured as 1 unit of running metre.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground to a depth not less than 2.25 mtrs below ground level with top edge of earth plate not less than 1.5 mtrs below normal ground level connected to GI earth wire 4 mm dia drawn through and including GI protection pipe of light grade 15 mm bore by means of bolts, nuts, check nuts and washers including excavation earth work provisioning of PCC chamber made of PCC 1:3:6 RCC cover funnel with wiremesh 20mm dia watering pipe Medium grade, GI protection pipe 20mm dia bore all as specified in Electrical Plate No.3 of SSR Part I, 2009 all as specified and directed.

Supply and fix Mild steel rod for ceiling fans of 3 mtr long duly screwed threads with check nuts & pin for ceiling fan including hooks for fixing fan complete all as specified and as directed

Supply and fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep, minimum air delivery not less than 220 CFM with service value 6.00 BEE, Five star rated with brushless direct current motor (BLDC) without remote all as specified and directed.

Supply and fix Heavy duty Exhaust fan, metal body, 300mm sweep, RPM not less than 1400 RPM, Air delivery not less than - 1300 CuM/Hr, 230 volts AC Supply with louvers including opening in wall and fixing arrangement with nut bolts and making good the disturbed surface all as specified and as directed.

Supply and fix GI Tubes of size 40mm, 'Medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Supply and fix Vertical type TPN DB 4 way double door with incoming MCCB FP 415 volts AC 3 phase 50 Hz, 16KA breaking capacity with fized magnetic setting for current ranging of capacity 100 Amps confirming to IS-13947 (P-2) IEC:947 made out of CRCA sheet housing with powder coating & confirming to IS 13032, IS 8623, BS 5486 accomdated suitably in a MS enclosure weather proof having hinged and robust locking arrangement duly powder coated complete all as specified and directed.

Supply and Laying LT UG cable of size 3.5 core x 25 sqmm in trenches /floors/on wall /service connections XLPE insulated, PVC sheathed and armoured 1100 volts grade with aluminium conductor complete all as specified and directed

Supply and Laying LT UG cable of size 2 core x 16 sqmm in trenches /floors/on wall /service connections XLPE insulated, PVC sheathed and armoured 1100 volts grade with aluminium conductor with necessary end terminal /cable gland as per site requirement including connecting to the main switches /cut outs MCB/MCCB with necessary lugs after cutting to required length and also including removing the existing unseviceable cable complete all as specified and directed

Excavation in trenches not exc 1.5 mtr width and not exc 1.5 mtr in depth and getting out in hard /dense soil for laying /taking out of LT UG cable complete all as specified and directed.

Returning , filling in incl spreading, leveling , watering and well ramming in layers not exc 25 cm thick in soils.

Removal of surplus soil to a distance not exc 50 mtr away and depositing where directed as a level not exc 1.5 mtr above the starting point all as directed.

Supply and lay unreinforced pre cast concrete cable covers class LV type-2, flat, size 250mm x 150mm x 40mm all as specified and directed.

Supply , spread and filling approved sand in cable trenches for cushioning of LT UG cable complete all as specified and directed.

Supply and lay G I tubing light grade in protection of cable at road crossing /hard standing/pole protection fixed with clamps as per site requirement etc all as specified and directed of size 50 mm dia bore.

Supply and fix recess mounting with perforated sheet with electronic driver luminaire 36 watts LED slim panel with central opal diffuser series mounted in ceiling surfaces including all accessories with new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make - Havells Cat No - STARTO2X2PLR36WLED840MOD incl driver LED DRIVER36V36WS, Wipro Cat No - CRCO23R036HP65G3 and Philips Cat No RC383B LED36S-6500 PSU OD WH PIR.

Taking down existing old vintage ceiling/exhaust fans and depositing to MES store yard as per directed .

C R R CONSTRUCTIONS

Sukhdevraj Sharma Engineers & Contractors Pvt Ltd