REPAIRS TO HARD STANDING COMPOUND WALL GATE FENCING DRAIN FOOTPATHS AND OTHER MISC WORKS AT AUNDH MIL STN UNDER GE MH AND RH KIRKEE

Amount

Demolition of brickwork or stone work/boulder masonary built in cement mortar or cement lime mortar all as specified

M&L for precast cement concrete, type C-1, 1:3:6 (20mm graded aggregate ) masonary with solid blocks, exc 10cm in width and setting in cement mortar (1:4) complete all as specified and directed.

All as per item No 2 above except blocks old serviceable bricks recovered from item No 1 above complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement morter 1:4 with water proofing compound complete all as specified and as directed.(Note : WPC shall be measured and paid separetely)

Supply only intergral water proofing compound.

M&L for preparation of new undecorated surface of wall and applying two coats of cement base paint over a coat of primer.

M&L preparation old decorated surfaces of walls and applying one coat of cement base paint all as specified.

M&L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces in cement morter 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new undecorated surface of wall and applying three coats of white wash on wall complete all as specified in SSR part-I (2009) and as directed.

M&L preparation old decorated surfaces of walls and applying one coat of white wash complete all as specified.

Dismantling fencing, wire mesh any type complete all as specified and directed by Engr in Charge

Dismantling of RCC post or struts carefully of any section embedded in natural ground incl taking out embedded portion and making good disturbed ground incl taking down/out worn out unserviceable old barbed wire, chain link fencing complete.

All as per item No. 13 here in before but embedded in concrete.

Excavation in post hole each n.exc 0.50 Cum getting out returning filling in and ramming earth around in layers n.exc 25cm watering and removed surplus soil to a distance n.exc 50m in soft/loose soil.

S&F Mild steel for posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0

S&F 15 mm dia of shank Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed.

M&L for cement concrete in foundation PCC 1:3:6 type C2 using 40mm graded stone agg for fencing post etc.

Supply only Chain link MS galvanised fencing, any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

S&F in repairs galvanised 2 strand barbed wire 2.24mm dia of wire and 2mm dia of barbed at 75mm spacing and straining and fixing to any type of strandre nails straining bolts, including securing or tying at crossing with and provn of galvanised MS wire staples or steel pins etc as specified.

All as per item No. 22 here in before but fixing only all old wire fit for reuse as directed.

S&F in repair Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

Dismantling structural steel work including doors, gates but excluding framed truss etc.

M&L for Rolled mild Steel Joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) (Fe 410 W (Grade E 250) quality A) complete all as specified and directed.

M&L for Rolled mild Steel for roof trusses (framed) tussed, purlins, crane gentries rails and fastenings and heavy brackets framing (Beam, tee angle channels or flat sections) including distnce pieces and cleats etc.(Fe 410 W (Grade E 250) quality A) complete all as specified and directed.

M&L for Rolled miled steel plate (plain or chequred) chanel square cut or notched (ordinary or counter shunk ) forming holes without any attachements (Fe 410 W (Grade E 250) quality A) complete all as specified and directed.

S&F Mild steel screw bolts (machine made) 11 to 15mm dia of neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10cm long.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old Roof sheet CGI/ PGI Sheet as specified and directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old Roof sheet CGI/ PGI Sheet complete all as specified and directed.

M&L for preparation of untreated new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint ( 1st grade quality ) over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old treated steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint ( 1st grade quality ) complete all as specified and as directed.

Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level)

M&L for cement concrete type D-2, 1:4:8 (40mm graded aggregate) 75 mm thick sub base or similar items all as specified and directed.

M&L fo Sand filling under floors or in foundation including watering and consolidation

M&L for 80mm thick coloured rubburised, glossy finish machine pressed interlocking pattern paver block any shape and size conforming to IS 15658-2006 of M-40 Grade incl all as specified and directed by Engineer-in Charge.

S&F Pre Polished Chequered cement concrete tiles glossy and rubburised finish 30cm x 30cm x 25mm thick, set, jointed and pointed in near cement slurry in floors including 15mm thick screed bed in CM 1:6 under tiles incl all as specified and directed by Engineer-in Charge.

M&L for PCC 1:3:6 type C-1 , 75 mm thick as in plinth protection, Path, floor construction joint after every 2 mtr interval and from wall will be filled by mastic of bitumin/Compound grade 'A' all as specified and directed.

M& for Forming Contraction (Dummy) joints 75 mm deep x 10mm wide, filled with sealing compound complete all as specified and directed by EIC.

Taking down PVC (SWR) pipes 75 mm dia single sockets and S&F in any length rubber ring joints, laid in trenches or in floor all as specified and directed.

M&L for Cement concrete type B2 (1:2:4) 40 mm graded aggregate as in surface channels and drains complete all as specified and directed.

Extra for fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc.

Demolition of cement concrete (re inforced) in roof floors, beams, staircase, landings, chajjas, pillars etc and similar suspended works and removing materials from site of work complete all as directed.

Separating scraping and cleaning of reinforcement (Demolition of concrete measure separately)

M&L for precast cement concrete type B-1 1:2:4 (20mm graded agg) set in CM 1:6 as in cover slabs for manholes etc.

S&F TMT bars 6 to 8mm dia bar, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Excavation in trenches n exc 1.50m wide and 1.50m depth for foundation, man hole etc and getting out in hard/dense soil.

Returing filling in including spreading leveling watering well ramming in layers n;exc 25cm thick with soil obtained from excavation

Removing excavated material exc. 250 m but n.exc. 500m and depositing where directed

M&L for B-1 1:2:4 (Nominal Mix), (20mm graded agg) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified

M&L for RCC B-1 1:2:4 (Nominal Mix), (20mm graded agg) in columns, pillars, piers, posts and struts all as specified

M&L for RCC type B-1 1:2:4 (Nominal Mix), (20mm graded agg) as in Beams, cantilevers, bressummers, lintels over 1.5m span.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter all as specified.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions all as specified

Formwork to sides of and soffits of floor or roof beams, lintels cantilevers all as specified

S&F of Mild TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Fe-410-W (Gde.E-250)

All as per item No 57 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

Dismantling floor, hearth or wall tiling including cement mortar bedding/complete and removing rubbish off the premises complete all as specified and directed.

M&L Coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick plastering in cm 1:4 all as specified.

Demolition of Stone slabs and tiles of any description or thickness laided bedded and pointed in cement mortar in floors, aprons etc.

M&L for 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete fixed over and including backing coat of 10mm thickin CM 1:4 all as specified

S&F in repair Drain cover of size 600x600mm thickness 60-70 mm with fine finished with perforated holes 20/25mm and set the same at the site including removing old from site in any position complete all as specified and directed by EIC

S&F in repairs Medium duty precast cover slab of size 300x300mm thickness 60-70 mm with fine finished with frame at the same at the place including removing old from site in any position complete all as specified and directed by EIC

kk construction

M/s IBEX Engineers and Contractors

s.k.engineers

ANJALI CONSTRUCTIONS

MAHESH DADAJI BACHHAV

J J ENTERPRISES

S.R.M.K Enterprises