REPAIR OF WOODEN/STEEL JOINERY, REPAIR TO LAGGING OF INTERNAL WATER SUPPLY FITTINGS, SUNKEN TREATMENT, PLUMBING STAKS, TANK CLEANING AND REPLACEMENT OF OTHER B/R MISC ITEMS OF MD/OTM ACCN , WELCOME MAINT AND OTHER WORKS AT JAK LI RC UNDER GE 970 EWS

Amount

Taking down chowkats or frames not exceeding 1.50 sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed.

Taking down chowkats or frames exceeding 1.50 sqm but not exceeding 4.00sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed.

Taking down shutters of any description not exceeding 1 sqm each, complete all as specified and directed.

Taking down shutters of any description exceeding 1 sqm but not exceeding 2Sqm each, complete all as specified and directed.

Demolition of brick work built in cement mortar , complete all as specified and directed.

M&L Labour for brick work with sub class `B’ bricks, straight on plan exceeding 6m mean radius built in CM 1:6 complete all as specified and directed.

Description all as per item No 06 above but except bricks , complete all as specified and directed.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over screed bed of 15 mm thick 1:3 , complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and directed.

S&F solid PVC door frame of size 50x47mm made of 5mm plain colour PVC sheet reinforced with MS square tube supply & fixing Sintex Polycon and equivalent complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length , complete all as specified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, , complete all as specified and directed. (Note: The unit rate quoted by contractor includes cost of glass & wiremesh and includes all other connected accessories Net opening will be measured for payment purpose.)

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (The unit rate quoted by contractor includes cost of 5mm thick tinted glass & stainless steel wiremesh and all other connected accessories Net opening will be measured for payment purpose.)

S&F factory made UPVC white colour fixed window made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick tinted glass glass (Note: The unit rate quoted by contractor includes cost of 5mm thick tinted glass and all other connected accessories Net opening will be measured for payment purpose.)

Supply and fixing factory made uPVC white colour Casement window frame with shutter single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension (Area of window upto 0.75 sqm.) comprising of uPVC multichambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (Note: The unit rate quoted by contractor includes cost of wiremesh and glass includes all other connected accessories Net opening will be measured for payment purpose.)

Supply and fixing factory made uPVC white colour Casement door shutter with frame with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in-Charge. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. The unit rate quoted by contractor includes cost of glass and includes all other connected accessories Net opening will be measured for payment purpose.

S&F of 12 mm thick Toughned Glass Door with patch fittings with cover plate of SS304 Grade including Decorative type Stainless steel 304 grade floor Spring, fixing/moving arrangement at top, Stainless steel 2 Nos H Type Handles of 450 MM suitable size as directed, Fin Connect Patch Lock etc in each door, including cutting holes in any size in floor and wall , complete all as specified and directed.

S&F 12mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required with patch fittings with cover plate of SS304 Grade, necessay accessories etc, complete all as specified and directed.

S&F Solar control film 50 micron thick reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified and directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings , complete all as specified and directed.

S&F in repair aluminium sheet powder coated of thickness not less than 4mm thick to be in sealed as panel in aluminium door including fixing complete all as specified and directed.

Supply and fixing for aluminium alloy anodized (powder coated) door fame and shutters with hollow aluminium anodized section as specified, shutter (two panels) fully glazed / partly glazed or fully panelled with and including 18mm thick (both side) prelaminated block board exterior grade / 5.5mm thick tinted or plain glass including aluminium alloy anodized snap type beads, dish type door handles, glazed clip joint cleats, rubber gasket, dead lock 4 levers, two numbers of aluminium alloy anodized tower bolts to each leaf, stainless steel hinges 3 Nos etc. including fixing frame to brick wall/ RCC members with rawl plugs complete all as specified and directed. Sections of doors shall be aluminium hollow sections as follows:- (a) Door frmae single groove 101mm x 44mm x 3mm thick. (b) Shutter top 83 mm x 44mm x 3mm thick. (c) Shutter bottom 114 mm x 44mm x 3mm thick. (d) Shutter vertical top 85 mm x 44mm x 3mm thick. (e) Shutter middle 83 mm x 44mm x 3mm thick. (f) Gauging clip weighing not less than 0.0978kg/metre. NOTE: (i) The rates shall be inclusive of supply & fixing of rubber packing / gasket, SS wire mesh & glass pane of sutiable size and all necessary arrangement to fixing frame with brick wall / concrete surface. (ii) The rates shall be inclusive to make good the damage portion of brick wall / concrete surface with PCC 1:3:6 & CM (1:3) to match with existing surface.

Material & labour Three Track powder coated anodised aluminum frame and shutters for windows and ventilators with for anodised aluminium shutters for windows and ventilators with for anodised aluminium shutter two Nos fully glazed 5.5 mm thick tinted or plain glass with one No shutter having stainless steel mosquito proofing net 0.63 mm dia with 1.40 mm aperature with and including necessary rubber packing aluminium beading and necessary locking arrangement and powder coating of any colour (Thickness or powder coating not less than 50 micron) complete all as specified and directed. Sections of window shall be aluminium sections as follows:- (a) Three track frame bottom and top section 92 mm x 31.75 mm x 1.3 mm thick with weight 1.065 KG per RM. (b) Three track frame bottom and top section 92 mm x 31.75 mm x 1.3 mm thick with weight 0.929 KG per RM. (c) Shutter bottom and top 40 mm x 18 mm x 1.55 mm thick with weight 0.547 Kg per RM. (d) Shutter sides 40 mm x 18 mm x 1.55 mm thick with weight 0.547 Kg per RM. NOTE: (i) The rates shall be inclusive of supply & fixing of rubber packing / gasket, SS wire mesh & glass pane of suitable size and all necessary arrangemetn to fixing frame with brick wall / concrete surface. (ii) The rates shall be inclusive to make good the damage portion of brick wall / concrete surface with PCC 1:3:6 & CM (1:3) to match with existing surface.

Supply & fixing powder coated aluminium windows and ventilator shutters,sliding or fixed type without sash bars , aluminium section weighting 0.55 kg / m including necessary joining cleats , glazing clips ,roller, rubber packing, anodised aluminium snap beading , screws,anodised aluminium fitting such as peg stays hinges,handle,locking device, louvers, rollers etc. complete all as specified. (Note:- Glass pane and mesh will be measured and paid separately )

S&F Aluminium Powder coated designer grill of 5.5 mm dia and aperture of 75 mm fixed with and including including cutting the grill to proper opening size for fixing and operation of handles and aluminium powder coated flat section of size 50 x 1.5 mm and suitable aluminium anodised frame F/H section complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames incl punching or drilling out glazing pins/spring clip and providing and fixing new ones, complete all as specified and directed.

S&F Sheet tinted glass 4.8mm thick tinted glass and glazing in squares complete all as specified and as direccted

S&FSheet glass 3mm thick, ordinary quality and glazing with oil putty in squares in square n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F Sheet glass 4mm thick, ordinary quality and glazing with oil putty in squares in square exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F figured glass pin headed type and glazing with oil putty in square n. exc 0.5 sqm in each pane 3mm thick glass complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples , complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples , complete all as specified and directed.

Taking down of existing aluminium door of any description including renewal of unserviceable parts and refixing in the same opening, complete all as specified and directed. Note :- Wire mesh and glass will be measured separately.

Taking down of existing aluminium windows of any description including renewal of unserviceable parts (rubber beeding, handle, wheel (roller), lock etc) and refixing in the same opening , complete all as specified and directed. Note :- Wire mesh and glass will be measured separately.

M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and directed.

M&L for PCC 1:3:6 type C-1(using 20mm graded stone agg) for bed block for fixing hold fast , complete all as specified and directed.

M&L Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one or more rebates including necessary s&f lugs, Butt hinges, lock strike plate, etc complete, size of frame 125x60mm incl bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either side complete all as specified and directed.

M&L Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one or more rebates including necessary s&f lugs, Butt hinges, lock strike plate, etc complete, size of frame 105 x 60mm incl bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either side complete all as specified and directed.

S&F 35 mm thick, factory made 2nd class hardwood glazed and skeleton shutters, open rebated and prepare to receive gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for secruing glass/gauge etc size of member of shutter as specified in SSR Part-I Section 8 Clause 8.20(a), fitted to chowkats , complete all as specified and directed.

S&F 35mm thick plain, frame 2nd class hard wood panelled shutter (any no of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers all as spd, complete all as specified and directed.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panesls, commercial type on bothe sides complete all as specified and as directed.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty incl making hole and fixing with cement , complete all as specified and directed.

S&F in repair door closer aluminium extruded section hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed, complete all as specified and directed.

S&F in repair MS mortice lock vertical type, 4 lever of size 100mm size , complete all as specified and directed.

S&F in repair mild steel 300mm, ordinary rat rail rod pattern springs, including roller and roller plate complete all as specified and directed.

S&F 18mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and as directed

M&L for 0.9mm thick decorative laminate type 1 of surface finish, colour and patters as approved, fixed with approved adhesive as per manufacturer's insturctions, complete all as specified and directed.

M&L for stainless steel telescopic channel for drawers not less than 45 cm long , complete all as specified and directed. Make : Hettich or equivalent .

S&F Push to open Magnetic Catches for kitchen cabinet doors complete all as specified Make Hettich or equivalent.

S&F Stainless sensys soft close 0 crank concealed slide on cabinet Hinge, a base of 12.5 (crank 0 degree) with mounting plate (shutter thickness 15-24mm) complete all as specified and directed

S&F Stainless Steel Decorative Cabinet Handle 100 mm complete all as specified and directed

S&F Floor door stopper of aluminum alloy body and tongue anodized with hard drawn steel spring fixed in floor of length 150mm , complete all as specified and directed.

S&F Stainless Steel butt hinges medium weight of size 100 mm fixed with stainless screws , complete all as specified and directed.

S&F Extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed .

S&F 200mm size aluminium anodised, barrel tower bolt of extruded section, complete all as specified and directed.

S & F 150 mm long aluminium anodized barrel tower bolts of extruded section lcomplete all as specified and as directed.

S&F 250 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified directed.

S&F door seal bottom with powder coated aluminium frame and black rubber, door air gap rubber shield, anti rust for gaps between the door and the floor fixing with screws, complete all as specified and directed.

S&F Decorative Stainless steel tubular curtain rail of 25mm dia incl six nos curtain ring per running mtr and one number of brackets on each end and one no of globe on each end of the rod per opening of door / window (make and materail approved by Engineer-in-charge) complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc raking out joints hacking for key scrabbing down water etc , complete all as specified and directed.

M&L for 15mm thick cement plaster in CM (1:4) on fair faces of brick or concrete surfaces using WPC where ever required as per manufacturerer's instructions and finishing the surface even and smooth (without using extra cement) etc. incl finishing even and fair, complete all as specified and directed. NOTE -WPC shall be measured and paid separetely.

M&L for rendering 15mm thick on fair faces of brick work in CM 1:6 finished even and fair without using extra cement, complete all as specified and directed.

M&L for applying two coats of synthetic eneamel painting over a coat of pink primer on new wooden surfaces exc 10 cm width or girth including preparation of surfaces, complete all as specified and directed.

M&L for two coats of synthetic enamel painting over a coat of red oxide zinc chrome primer on new steel surfaces over 10cm width or girth including preparation of surface, complete all as specified and directed.

Preparing new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted over & including a coat of primer, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall applying a layer of wall care putty 2mm thick (averaging) , Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed

M&L Lagging to pipes used in internal water supply (internal dia of pipe 20mm) or plumbing all round with,25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842 , complete all as specified and directed.

M&L Lagging to pipes used in internal water supply (internal dia of pipe 25mm) or plumbing all round with,25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842 all as specified and directed by the Engr-in-Charge.

Taking up or down GI Water Tubing/PPR pipes 15/16mm dia (bore) including Connections and Fittings, segregating serviceable Pipes & Fittings and Stacking properly at Site(s) for re-use, complete all as specified and as directed.

Description all as per ser Item No. 70 above but for 20mm dia (Bore), complete all as specified and directed.

Description all as per ser Item No. 70 above but for 25mm dia (Bore), complete all as specified and directed.

M&L refixing old steel tubing and connections 20mm received from item no 71 in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed.

Description all as per ser Item No. 73 but for 25mm dia (Bore)complete all as specified and as directed.

M&L for 3-layer PP-R (Polypropylene random copolymer) outer diameter of pipes 20 mm (Inner dia 14.40 mm) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors et ccomplete all as specified and as directed.

Description all as per ser Item No. 75 but outer diameter of pipes 25 mm (Inner dia 18.00 mm) ccomplete all as specified and as directed.

Description all as per ser Item No. 75 but outer diameter of pipes 32 mm (Inner dia 23.20 mm) ccomplete all as specified and as directed.

S&F in repair 20mm dia PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and as directed

S&F in repair 25mm dia PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and as directed

M&L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and as directed.

M&L for cleaning of water tank of capacity not exc 250 ltrs removing all scale and dirt etc. by brushing with iron brushes, removing green algae etc. by using bleaching powder, all from tanks and from mouths of circulating pipe etc. complete all as directed by Engineer -in- Charge. (Note : The Contractor will write date of cleaning on tank as complete all as specified and as directed.

Description all as per ser item No 81 above, but exc 250 ltrs and not exc 500 ltrs capacity complete all as specified and as directed.

Description all as per ser item No 81 above, but exc 500 ltrs and not exc 1000 ltrs capacitycomplete all as specified and as directed.

Description all as per ser item No 81 , but exc 1000 ltrs and not exc 2000 ltrs capacity complete all as specified and as directed.

S&F in repair 15 mm Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed.

Description all as per ser item No 85, but for 20mm dia (Bore) complete all as specified and as directed.

Description all as per ser item No 85, but for 25mm dia (Bore) complete all as specified and as directed.

M&L for preparing surface of sunken slab and applying 15mm thick cement plaster 1:3 cement sand mortar with integral water proofing compound both on floor & wall. The surface shall then be cured and allowed to dry then applying Epoxy Resin coating Polymer modified cementation coating like brush bond of Fosroc, Pidilite and Bostic as per manufacturers instructions both on floor as well as on wall and sunken floor shall be filled with graded cinder concrete upto top level to receive top flooring, incl providing 25mm dia GI spout pipe projecting 0.25mtr beyond the external face of wall complete all as specified and as directed.

M&L for 40mm thick PCC 1:2:4 type B-0 as in Sunken Portion of WC/Bath room (using 12.5mm graded stone aggregate) complete all as specifed and directed.

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and as directed.

M&L 100 mm thick PCC (1:4:8 ) type D-2 as in sub base finished even and rough complete all as specified and as directed.

M&L 75 mm thick PCC (1:4:8 ) type D-2 as in sub base finished even and rough complete all as specified and as directed.

M&L 75mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection incl finishing even and smooth w/o using extra cement complete all as specified and as directed.

M&L for 25mm thick PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) as in level course with finshining in cement concrete surface even and rough to receive screed bed complete complete all as specified and as directed.

M&L for brick work with sub class `B’ bricks, straight on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and as directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slab, floor slabs landings and sgh finished surfaces of concrete flat complete all as specified and as directed.

M&L for RCC 1:2:4 type B-1, Slab supported on walls,beams and columns in floors,roof, landing, balconies,in type B1(20mm graded aggregate) complete all as specified and as directed.

M & L for mild steel TMT bars ,10mm dia and over , cut to length , bent to shspe required incl cranking , bending spirally for hooping for coloumns , hooking ends andbionding with (annealed) not less than 0.90 mm dia all a specified and directed

Dismantling floor, hearth, wall tiling including taking down plastering in cement mortor removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for double charged premium quality Vitrified tiles 9 to 10 mm thick light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding Layer in cement mortar 1:6 complete all as specified and directed.

M&L for double charged premium quality Vitrified tiles 9 to 10 mm thick light shade (square/ rectangular) polished, area of each tiles tiles not exceeding 0.36 sqm, in skirting/ dado or verticle surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick plaster in CM 1:4 complete all as specified and directed.

M&L Joint free Non-skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match complete all as specified and as directed

M&L Joint free Non-skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in skirting/dado or verticle surfaces with back coat of screed bed or bedding layer of 10 mm thick 1:4 and pointed in white or coloured cement to match complete all as specified.

M&L Joint free Non-skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match complete all as specified and as directed

M&L Glazed coloured ceramic tiles in verticle surfaces 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match with backcoat of screed bed or bedding layer 10mm thick 1:4 and pointed in white or coloured cement to match complete all as specified.

M&L Johnson Endura premium paving tiles of techno commercial or equivalent of size 40cm x 40cm x 10 mm thick, set, jointed and pointed in neat cement slurry in floors, laid over 15 mm thick bedding layer in Cement Mortar 1:6 complete all as specified and as directed.

S&F in repair 15mm dia bib taps CP Brass with Capstanhead, screwed down, screwed for iron pipe of bore 15mm complete.

S&F in repair 15mm dia bib taps, fancy type long body chromium plated cast copper alloy with crutch or butterfly handle complete all as specified and directed.

S & F in repair brass CP pillar taps fancy type for iron pipe of bore 15mm fancy type with capstan head.

S&F in repair brass Chromium plated Basin Mixer valve hot and cold screwed down for iron pipe complete all as specified and as directed.

S&F in repair Brass CP Wall mixer for mixing hot & cold water (3 in 1) screwed down for iron pipe and fixed bore of pipe 15mm complete all as specified and as directed.

S&F in repair Stop valves,15mm fancy type, chromium plated with long shank and cup (concealed type) cast copper alloy,screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

S&F in repair Brass chromium plated shower rose 125mm size with shower arm, including fixing to steel pipe or union complete all as specified and directed.

S&F PVC waste pipe 32mm dia of cup with over all length of pipe 90cm complete all as specified and directed.

S&F PVC urinal waste pipe 50 mm dia of cup with screw and over all length of pipe 90cm complete all as specified and directed.

S&F Soap Dish CP Stain Less Steel complete all as specified and directed.

S&F toilet paper holder with flat recessed type stainless steelcomplete all as specified and directed.

S&F Peg Set of 6 with base plate stainless steel complete all as specified and directed.

Supply & Fixing Corner Glass Shelf 300mm (with ABS Brackets)complete all as specified and directed.

S&F Brass CP Sink Mixer with regular spout for mixing hot & cold water screwed down for iron pipe and fixed bore of pipe 15mmcomplete all as specified and directed.

S&F Glass shelf 450 x 125 x 6MM (with ABS Bracket chromium plated bracket guard and SS railingcomplete all as specified and directed.

Supply& Fixing tubular towel Rail CP Brass, chromium plated D type with CP Brackets, 600 mm long between flanges all as specified.

S&F in repair vitreous China squatting pan, Orissa pattern incl PVC trap, size 580 x 440 mm white, with integral foot rests squat pattern closet also includes setting the trap and pan in cement concrete (1 cement, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing (thickness as indicated) and making good floor complete all as specified incl cutting to the flush pipe and necessary repair to the floor complete all as specified and directed.

S&F Vitreous China wash downwater closet pan (pedestal pattern), white (including fixing bolts & flush pipe, plastic water closet seat,black, closed pattern with bottom, and cover and mild steel chromium plated or aluminised hinging device etc.) complete all as specified and directed.

S&F one piece floor mounted vitreous china EWC with integrated flushing cistern, soft closing seat cover and necessary nut/bolt for fixing complete all as specified and directed.

Supply & fixing PVC Flushing Cistern 10 litre capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle including 32mm dia PVC Flush Pipe, a Pair of MS Brackets,CP flush bend including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 including taking down unserviceable Flushing Cistern and connected Items of any description, complete all as specified and as directed.

S&F wash hand basin of vitreous china counter sunk size 560mm x 410mm x 180mm, PVC waste pipe 32mm dia, waste coupling brass chromium plated and including cutting complete all as specified and directed.

S&F Vitreous China Urinal, full stall type, including, urinal spreader, waste coupling and waste pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, grating and Union for discharge pipe complete all as specified and as directed.

Supply and fixing sinks with out drainage board made of stainless steel 0.75mm thick kitchen or laboratory, overall size 430mm x 510mm bowl size 430mm x 380mm x 203mm complete all as specified and directed.

S & F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F stainless steel plate rack of size 24 x 30 x 10 inch of best quality including necessary stain less steel screws, rawl plugs and washers complete all as specified and directed.

S&F in repair PVC Connections 15mm size with PTMT Nuts of length 450mm and fixed, complete all as specified and as directed.

S&F in repair PVC Connections 600mm long complete all as specified.

S&F in repair Aluminium Grip (Hot & Cold) connections pipe for Basin Mixer/Geyser/Hot and Cold connection pipe Hose Pipe of length 600mm long fixed, complete all as specified and as directed.

Dismantling of PVC / CI pipe 100mm dia jointed in cement mortar and taking out of trench if required complete all as specified.

Dismantling of PVC / CI pipe 75mm dia or less jointed in cement mortar and taking out of trench if required complete all as specified.

S&F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls and making good with cement mortor 1:3 complete all as specified and directed.

S&F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in trenches or in floorsand making good with cement mortor 1:3 or with PCC 1:2:4 complete all as specified and directed.

S&F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls and making good with cement mortor 1:3 or with PCC 1:2:4 complete all as specified and directed.

S&F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in trenches or in floors and making good with cement mortor 1:3 or with PCC 1:2:4 complete all as directed.

S&F in repair PVC 110 mm bore Bend complete all as specified and as directed.

S&F in repair PVC (SWR) junction single, (Single T) equal or unequal with access door in 110 mm bore complete all as specified and directed.

S&F in repair PVC 75 mm bore Bend complete all as specified and as directed.

S&F in repair PVC 75 mm bore Bend with access door complete all as specified and as directed.

S&F in repair PVC (SWR) junction single, (Single T) equal or unequal with access door in 75 mm bore complete all as specified and directed.

S&F in repair PVC (SWR) vent cowl 110 mm bore complete all as specified and as directed.

S & F in repairs for PVC (SWR) floor/Nahani trap 75 mm dia outlet, plain with grating including jointing with solvent cement to waste pipe, fixed in cement concrete type B-1 (1:2:4)

S&F Box type steel window (Fatory made) outer frame made out ERW tube 'P' section 65mm x 45mm x 25mm and shutter with glazed openable shutter of ERW tube 'P' section 50 mm x 35mm x 20 mm openable (double) shutter with glazed openable shutter on (external side) and wire gauzed openable shutter on (Internal side) with steel pintal hinges, steel handle 100 mm long, mild steel tower bolt 02 nos on each shutter, stopper of 'Z' section and its locking arrangement at mild steel hook and eye including 0.36mm dia nominal dia of stainless steel wire cloth avg width of aperture 1.40mm dia, 4 mm thick sheet glass window & 4mm figured glass for ventilators and guard bars (MS square bar 10mm dia), all as specified and as directedby Engr-in-Charge. Note. The quoted rate against the above item shall also include (i) For provn of one shop coat of zinc chromate primer on all exposed steel surfacces and one oat tar on the ends of steel frame in contact with bricks/concrete surface. (ii) 04 Nos MS Steel Lugs of 20 x 5mm, MS flat 20 cm long over all welded to frames. (iii) PCC block for embedding lugs. (iv) 0.36 mm dia SS wire mesh. (v) 4mm thick sheet glass for window. (vi) Guard bars.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) any thickness, including cover fillets but without frame work complete all as specified and directed.

S&F Powder coated galvanised iron frame work for seamless ceiling size 600mm x 600mm with main runner 38 x 24 x 0.90mm thick, cross tee 29 x 24 x 0.90mm thick and wall angle 24 x 24 x 0.90mm thick duly suspended with 6mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip complete all as specified and as directed.

S&F 6mm thick Non Asbestos fibre cement building boards/Pre Laminated self embossed texture designer E-Board classic (Size 0.60M x 0.60M/0.60M x 1.2 M), HPSC (High pressure steam cured) to be fixed or laid/inserted to existing/new timber/GI/Aluminium/MS framework with screws as in ceiling complete all as specified and directed.

Supply only WPC complete all as specified and directed.

M&L for 2mm thick wall care putty on wall complete all as specified and as directed

Dismantling water tanks of capacity exc 250 but not exc 500 ltr capacitycomplete all as specified and directed.

Supply & Fixing rotational moulded polythene water storage tanks tripple layer (cylindrical vertical with closed top) hoisted and fixed in postion 500 ltrs capacity with and including 25mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram complete all as specified and directed.

Dismantling water tanks of capacity exc 500 but not exc 1000 ltr capacitycomplete all as specified and directed.

Supply & Fixing rotational moulded polythene water storage tanks tripple layer (cylindrical vertical with closed top) hoisted and fixed in postion 1000 ltrs capacity with and including 25mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram complete all as specified and directed.

Dismantling water tanks of capacity exc 1000 but n.exc 2000ltrs complete all as specified and directed.

Supply & Fixing rotational moulded polythene water storage tanks tripple layer (cylindrical vertical with closed top) hoisted and fixed in postion 2000 ltrs capacity with and including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram complete all as specified and directed.

M&L Preparation of old plastered or painted surfaces of wall by complete removing with mechanical means/grinding of existing treatment by grinder machine (scrubbing, washing down etc) complete all as specified and directed.

M&L for applying one coat of wall putty of minimum 2 mm thick over & above complete treated surface as item No. 163 complete all as specified and directed.

M&L for applying two coats of oil bound distemper over item no 164 complete all as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over item no 2 complete all as specified and directed

M&L for complete removal of existing surface and applying two coat of Oil Bound Distemper over a coat of primer on old decorated/undecorated surfaces of Ceiling complete all as specified and as directed.

M&L for 2mm thick wall care putty on ceiling complete all as specified and as directed

Preparation of old decorated surfaces of wall and applying one coats of oil bound distemper complete all as specified complete all as specified and directed.

Prepration of old surfaces of ceiling and applying one coats of OBD complete all as specified and directed.

Preparation of old decorated surfaces of wall and applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over item no 2 complete all as specified and directed

Preparation of old decorated surfaces of wall and applying one coats of cement base paint complete all as specified complete all as specified and directed.

M&L for preperation of old painted steel surfaces and applying one coat of synthetic enamel paint over 10 cm in width or girth complete all as specified and directed.

M&L for preparation of old steel or iron surfaces of any description including removal of rubbish from roof surface as in roofing (corrugated /semi corrugated), exceeding 10 cms width or girth and applying one coat of synthetic enamel paint in approved colour & pattern complete all as specified and directed.

M&L for preperation of old painted wooden surfaces and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for Rendering 5mm thick in cement plaster 1:3 on ceiling surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of new plaster surface of wall and applying 2mm thick of wall putty, complete all as specified and directed.

M&L for preparation of new plaster surface of ceiling and applying 2mm thick of wall putty, complete all as specified and directed.

M&L for prepration of new plastered surfaces of ceiling and applying two coats of OBD complete all as specified and directed.

Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 complete all as specified

M&L for coloured non skid ceramic tiles 7 to 8 mm thick, area of each tile exc 0.11 sqm but n. exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in colored cement to match Shade, pattern, laying etc of tiles complete all as specified

M&L for viterified tiles light shade 10 mm thick (square/rectangular) polished , area of each tile n. exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in colored cement to match, pattern, laying etc of tiles and Shade, Colour shall be decided by Engr in Charge complete all as specified

S&F in repair angle cock, long shank fancy type C.P. cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions and fixed 15mm borecomplete all as specified and directed.

S&F stainless steel grating doom 100/75mm dia with or without hole as directed .(Min.weight 25gms) complete all as specified and directed.

S&F in repairs vitreous china wash basin pedestal type white, flat back, size 600 x 480 mm excluding taps, waste, chain & plug and porcelain stopper but including brackets, 32 mm bore waste coupling complete all as specified and directed.

Notes :- Amount of Credit Schedule for Schedule 'A' Part-ll shall be deducted from total quoted amount of BOQ to arrive at the contract sum

M/S BILAL AHMAD SOFI (BID ID -3373619)

M/S BASHIR AHMAD TANTARY (BID ID -3378814)

SOFI CONSTRUCTIONS (BID ID -3377399)

G N Constructions (BID ID -3378721)

M/S JAN BUILDERS (BID ID -3378091)

M/s A B CONSTRUCTION (BID ID -3377518)

M/s Nasir Rasool Dar (BID ID -3378205)

MEGA CONCRETE CONSTRUCTION ENGINEERS AND CONTRACTORS (BID ID -3378427)